From: Saurav Kashyap <saurav.kashyap@qlogic.com>
To: jbottomley@parallels.com
Cc: giridhar.malavali@qlogic.com, saurav.kashyap@qlogic.com,
andrew.vasquez@qlogic.com, linux-scsi@vger.kernel.org
Subject: [PATCH 07/20] qla2xxx: Enable the Flash Access Control (FAC) mailbox command.
Date: Fri, 13 Dec 2013 15:03:47 -0500 [thread overview]
Message-ID: <1386965040-20611-8-git-send-email-saurav.kashyap@qlogic.com> (raw)
In-Reply-To: <1386965040-20611-1-git-send-email-saurav.kashyap@qlogic.com>
From: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
---
drivers/scsi/qla2xxx/qla_init.c | 5 +----
1 files changed, 1 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c
index e7e5f4f..9b271cc 100644
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
@@ -1718,9 +1718,6 @@ enable_82xx_npiv:
spin_unlock_irqrestore(&ha->hardware_lock, flags);
}
- if (IS_QLA83XX(ha))
- goto skip_fac_check;
-
if (rval == QLA_SUCCESS && IS_FAC_REQUIRED(ha)) {
uint32_t size;
@@ -1733,7 +1730,7 @@ enable_82xx_npiv:
"Unsupported FAC firmware (%d.%02d.%02d).\n",
ha->fw_major_version, ha->fw_minor_version,
ha->fw_subminor_version);
-skip_fac_check:
+
if (IS_QLA83XX(ha)) {
ha->flags.fac_supported = 0;
rval = QLA_SUCCESS;
--
1.7.7
next prev parent reply other threads:[~2013-12-13 20:37 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-13 20:03 [PATCH 00/20] qla2xxx: Patches for scsi "misc" branch Saurav Kashyap
2013-12-13 20:03 ` [PATCH 01/20] qla2xxx: Add mutex around optrom calls to serialize accesses Saurav Kashyap
2013-12-13 20:03 ` [PATCH 02/20] qla2xxx: Add handling for boot indication progress AENs for ISPFX00 Saurav Kashyap
2013-12-13 20:03 ` [PATCH 03/20] qla2xxx: Replace constant value for IOCTL IOCB abort execution status with a macro " Saurav Kashyap
2013-12-13 20:03 ` [PATCH 04/20] qla2xxx: Use proper message for Non owner reset ACK Timeout Saurav Kashyap
2013-12-13 20:03 ` [PATCH 05/20] qla2xxx: Remove init control block related dead code for ISPFX00 Saurav Kashyap
2013-12-13 20:03 ` [PATCH 06/20] qla2xxx: Select correct request queue for error type IOCB " Saurav Kashyap
2013-12-13 20:03 ` Saurav Kashyap [this message]
2013-12-13 20:03 ` [PATCH 08/20] qla2xxx: Properly handle 32 bit mailbox register " Saurav Kashyap
2013-12-13 20:03 ` [PATCH 09/20] qla2xxx: Set host can_queue value based on available resources Saurav Kashyap
2013-12-13 20:03 ` [PATCH 10/20] scsi_transport_fc: Add 32Gbps speed definition Saurav Kashyap
2013-12-13 20:03 ` [PATCH 11/20] qla2xxx: Add support for ISP2701 Saurav Kashyap
2013-12-16 6:56 ` Bart Van Assche
2013-12-13 20:03 ` [PATCH 12/20] qla2xxx: Remove Marker type IOCB logic for ISPFX00 Saurav Kashyap
2013-12-13 20:03 ` [PATCH 13/20] qla2xxx: Remove ISP_ABORT_NEEDED and ISP_ABORT_RETRY checks from watchdog function for ISP8044 Saurav Kashyap
2013-12-13 20:03 ` [PATCH 14/20] qla2xxx: Add changes in the IOCB structures to adjust driver source codes to ISPFX00 firmware spec Saurav Kashyap
2013-12-13 20:03 ` [PATCH 15/20] qla2xxx: Avoid poisoining in the response queue for ISPFX00 Saurav Kashyap
2013-12-16 6:56 ` Bart Van Assche
2013-12-13 20:03 ` [PATCH 16/20] qla2xxx: Simplyfy the ISPFX00 interrupt handler code " Saurav Kashyap
2013-12-16 6:56 ` Bart Van Assche
2013-12-17 4:01 ` Saurav Kashyap
2013-12-13 20:03 ` [PATCH 17/20] qla2xxx: Read capture firmware dump on mailbox timeout for ISP8044 and ISP82XX Saurav Kashyap
2013-12-13 20:03 ` [PATCH 18/20] qla2xxx: Correctly set the read_optrom pointer for ISP8044 Saurav Kashyap
2013-12-13 20:03 ` [PATCH 19/20] qla2xxx: Fix multiqueue MSI-X registration Saurav Kashyap
2013-12-16 6:47 ` Bart Van Assche
2013-12-13 20:04 ` [PATCH 20/20] qla2xxx: Update the driver version to 8.07.00.02-k Saurav Kashyap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1386965040-20611-8-git-send-email-saurav.kashyap@qlogic.com \
--to=saurav.kashyap@qlogic.com \
--cc=andrew.vasquez@qlogic.com \
--cc=giridhar.malavali@qlogic.com \
--cc=jbottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).