From: Saurav Kashyap <saurav.kashyap@qlogic.com>
To: jbottomley@parallels.com
Cc: giridhar.malavali@qlogic.com, saurav.kashyap@qlogic.com,
andrew.vasquez@qlogic.com, linux-scsi@vger.kernel.org
Subject: [PATCH V2 02/20] qla2xxx: Add handling for boot indication progress AENs for ISPFX00.
Date: Mon, 16 Dec 2013 22:28:25 -0500 [thread overview]
Message-ID: <1387250923-1041-3-git-send-email-saurav.kashyap@qlogic.com> (raw)
In-Reply-To: <1387250923-1041-1-git-send-email-saurav.kashyap@qlogic.com>
From: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
---
drivers/scsi/qla2xxx/qla_def.h | 2 +-
drivers/scsi/qla2xxx/qla_mr.c | 3 +++
2 files changed, 4 insertions(+), 1 deletions(-)
diff --git a/drivers/scsi/qla2xxx/qla_def.h b/drivers/scsi/qla2xxx/qla_def.h
index 859c63a..02ad5d8 100644
--- a/drivers/scsi/qla2xxx/qla_def.h
+++ b/drivers/scsi/qla2xxx/qla_def.h
@@ -808,7 +808,7 @@ struct mbx_cmd_32 {
Notification */
#define MBA_FW_POLL_STATE 0x8600 /* Firmware in poll diagnostic state */
#define MBA_FW_RESET_FCT 0x8502 /* Firmware reset factory defaults */
-
+#define MBA_FW_INIT_INPROGRESS 0x8500 /* Firmware boot in progress */
/* 83XX FCoE specific */
#define MBA_IDC_AEN 0x8200 /* FCoE: NIC Core state change AEN */
diff --git a/drivers/scsi/qla2xxx/qla_mr.c b/drivers/scsi/qla2xxx/qla_mr.c
index ba6f8b1..6ca4807 100644
--- a/drivers/scsi/qla2xxx/qla_mr.c
+++ b/drivers/scsi/qla2xxx/qla_mr.c
@@ -997,6 +997,9 @@ qlafx00_init_fw_ready(scsi_qla_host_t *vha)
break;
default:
+ if ((aenmbx & 0xFF00) == MBA_FW_INIT_INPROGRESS)
+ break;
+
/* If fw is apparently not ready. In order to continue,
* we might need to issue Mbox cmd, but the problem is
* that the DoorBell vector values that come with the
--
1.7.7
next prev parent reply other threads:[~2013-12-17 4:01 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-12-17 3:28 [PATCH V2 00/20] qla2xxx: Patches for 3.13 scsi "misc" branch Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 01/20] qla2xxx: Add mutex around optrom calls to serialize accesses Saurav Kashyap
2013-12-17 3:28 ` Saurav Kashyap [this message]
2013-12-17 3:28 ` [PATCH V2 03/20] qla2xxx: Replace constant value for IOCTL IOCB abort execution status with a macro for ISPFX00 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 04/20] qla2xxx: Use proper message for Non owner reset ACK Timeout Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 05/20] qla2xxx: Remove init control block related dead code for ISPFX00 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 06/20] qla2xxx: Select correct request queue for error type IOCB " Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 07/20] qla2xxx: Enable the Flash Access Control (FAC) mailbox command Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 08/20] qla2xxx: Properly handle 32 bit mailbox register for ISPFX00 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 09/20] qla2xxx: Set host can_queue value based on available resources Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 10/20] scsi_transport_fc: Add 32Gbps speed definition Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 11/20] qla2xxx: Add support for ISP2071 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 12/20] qla2xxx: Remove Marker type IOCB logic for ISPFX00 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 13/20] qla2xxx: Remove ISP_ABORT_NEEDED and ISP_ABORT_RETRY checks from watchdog function for ISP8044 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 14/20] qla2xxx: Add changes in the IOCB structures to adjust driver source codes to ISPFX00 firmware spec Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 15/20] qla2xxx: Avoid poisoning in the response queue for ISPFX00 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 16/20] qla2xxx: Simplify the ISPFX00 interrupt handler code " Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 17/20] qla2xxx: Read capture firmware dump on mailbox timeout for ISP8044 and ISP82XX Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 18/20] qla2xxx: Correctly set the read_optrom pointer for ISP8044 Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 19/20] qla2xxx: Fix multiqueue MSI-X registration Saurav Kashyap
2013-12-17 3:28 ` [PATCH V2 20/20] qla2xxx: Update the driver version to 8.07.00.02-k Saurav Kashyap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1387250923-1041-3-git-send-email-saurav.kashyap@qlogic.com \
--to=saurav.kashyap@qlogic.com \
--cc=andrew.vasquez@qlogic.com \
--cc=giridhar.malavali@qlogic.com \
--cc=jbottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).