[PATCH V6 3/3] scsi: retry report-luns when reported LU count requres more memory

Rob Evers
2014-12-16T16:01:23Z

Update scsi_report_lun_scan to initially always report up to 511 LUs,
as the previous default max_report_luns did. Retry in a loop if not
enough memory is available for the number of LUs reported. Parameter
max_report_luns is removed as it is no longer used.

Signed-off-by: Rob Evers <revers@redhat.com>
---
drivers/scsi/scsi_scan.c | 41 +++++++++++------------------------------
1 file changed, 11 insertions(+), 30 deletions(-)

diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c
index 8db1f6f..88eee50 100644
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
@@ -99,20 +99,6 @@ char scsi_scan_type[6] = SCSI_SCAN_TYPE_DEFAULT;
module_param_string(scan, scsi_scan_type, sizeof(scsi_scan_type), S_IRUGO);
MODULE_PARM_DESC(scan, "sync, async or none");

-/*
- * max_scsi_report_luns: the maximum number of LUNS that will be
- * returned from the REPORT LUNS command. 8 times this value must
- * be allocated. In theory this could be up to an 8 byte value, but
- * in practice, the maximum number of LUNs suppored by any device
- * is about 16k.
- */
-static unsigned int max_scsi_report_luns = 511;
-
-module_param_named(max_report_luns, max_scsi_report_luns, uint, S_IRUGO|S_IWUSR);
-MODULE_PARM_DESC(max_report_luns,
- "REPORT LUNS maximum number of LUNS received (should be"
- " between 1 and 16384)");
-
static unsigned int scsi_inq_timeout = SCSI_TIMEOUT/HZ + 18;

module_param_named(inq_timeout, scsi_inq_timeout, uint, S_IRUGO|S_IWUSR);
@@ -1399,15 +1385,11 @@ static int scsi_report_lun_scan(struct scsi_target *starget, int bflags,

/*
* Allocate enough to hold the header (the same size as one scsi_lun)
- * plus the max number of luns we are requesting.
- *
- * Reallocating and trying again (with the exact amount we need)
- * would be nice, but then we need to somehow limit the size
- * allocated based on the available memory and the limits of
- * kmalloc - we don't want a kmalloc() failure of a huge value to
- * prevent us from finding any LUNs on this target.
+ * plus the number of luns we are requesting. 511 was the default
+ * value of the now removed max_report_luns parameter.
*/
- length = (max_scsi_report_luns + 1) * sizeof(struct scsi_lun);
+ length = (511 + 1) * sizeof(struct scsi_lun);
+retry:
lun_data = kmalloc(length, GFP_KERNEL |
(sdev->host->unchecked_isa_dma ? __GFP_DMA : 0));
if (!lun_data) {
@@ -1473,17 +1455,16 @@ static int scsi_report_lun_scan(struct scsi_target *starget, int bflags,
/*
* Get the length from the first four bytes of lun_data.
*/
+ if (get_unaligned_be32(lun_data->scsi_lun) +
+ sizeof(struct scsi_lun) > length) {
+ length = get_unaligned_be32(lun_data->scsi_lun) +
+ sizeof(struct scsi_lun);
+ kfree(lun_data);
+ goto retry;
+ }
length = get_unaligned_be32(lun_data->scsi_lun);

num_luns = (length / sizeof(struct scsi_lun));
- if (num_luns > max_scsi_report_luns) {
- sdev_printk(KERN_WARNING, sdev,
- "Only %d (max_scsi_report_luns)"
- " of %d luns reported, try increasing"
- " max_scsi_report_luns.\n",
- max_scsi_report_luns, num_luns);
- num_luns = max_scsi_report_luns;
- }

SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev,
"scsi scan: REPORT LUN scan\n"));
--
1.8.3.1