linux-scsi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ondrej Zary <linux@rainbow-software.org>
To: linux-scsi@vger.kernel.org
Subject: [PATCH 22/36] aha1542: clean up cmd variables
Date: Fri,  6 Feb 2015 23:11:43 +0100	[thread overview]
Message-ID: <1423260717-15944-23-git-send-email-linux@rainbow-software.org> (raw)
In-Reply-To: <1423260717-15944-1-git-send-email-linux@rainbow-software.org>

Make sure that there's no variable named cmd

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
---
 drivers/scsi/aha1542.c |   53 ++++++++++++++++++++++--------------------------
 1 file changed, 24 insertions(+), 29 deletions(-)

diff --git a/drivers/scsi/aha1542.c b/drivers/scsi/aha1542.c
index 1615865..dbe4659 100644
--- a/drivers/scsi/aha1542.c
+++ b/drivers/scsi/aha1542.c
@@ -124,7 +124,7 @@ static inline bool wait_mask(u16 port, u8 mask, u8 allof, u8 noneof, int timeout
    routine does not send something out while we are in the middle of this.
    Fortunately, it is only at boot time that multi-byte messages
    are ever sent. */
-static int aha1542_outb(unsigned int base, u8 cmd)
+static int aha1542_outb(unsigned int base, u8 val)
 {
 	unsigned long flags;
 
@@ -138,13 +138,13 @@ static int aha1542_outb(unsigned int base, u8 cmd)
 			spin_unlock_irqrestore(&aha1542_lock, flags);
 			continue;
 		}
-		outb(cmd, DATA(base));
+		outb(val, DATA(base));
 		spin_unlock_irqrestore(&aha1542_lock, flags);
 		return 0;
 	}
 }
 
-static int aha1542_out(unsigned int base, u8 *cmdp, int len)
+static int aha1542_out(unsigned int base, u8 *buf, int len)
 {
 	unsigned long flags;
 
@@ -155,7 +155,7 @@ static int aha1542_out(unsigned int base, u8 *cmdp, int len)
 			printk(KERN_ERR "aha1542_out failed(%d): ", len + 1);
 			return 1;
 		}
-		outb(*cmdp++, DATA(base));
+		outb(*buf++, DATA(base));
 	}
 	spin_unlock_irqrestore(&aha1542_lock, flags);
 	if (!wait_mask(INTRFLAGS(base), INTRMASK, HACC, 0, 0))
@@ -167,7 +167,7 @@ static int aha1542_out(unsigned int base, u8 *cmdp, int len)
 /* Only used at boot time, so we do not need to worry about latency as much
    here */
 
-static int aha1542_in(unsigned int base, u8 *cmdp, int len, int timeout)
+static int aha1542_in(unsigned int base, u8 *buf, int len, int timeout)
 {
 	unsigned long flags;
 
@@ -179,7 +179,7 @@ static int aha1542_in(unsigned int base, u8 *cmdp, int len, int timeout)
 				printk(KERN_ERR "aha1542_in failed(%d): ", len + 1);
 			return 1;
 		}
-		*cmdp++ = inb(DATA(base));
+		*buf++ = inb(DATA(base));
 	}
 	spin_unlock_irqrestore(&aha1542_lock, flags);
 	return 0;
@@ -244,8 +244,7 @@ static int makecode(unsigned hosterr, unsigned scsierr)
 static int aha1542_test_port(int bse, struct Scsi_Host *shpnt)
 {
 	u8 inquiry_result[4];
-	u8 *cmdp;
-	int len;
+	int i;
 
 	/* Quick and dirty test for presence of the card. */
 	if (inb(STATUS(bse)) == 0xff)
@@ -273,13 +272,10 @@ static int aha1542_test_port(int bse, struct Scsi_Host *shpnt)
 
 	aha1542_outb(bse, CMD_INQUIRY);
 
-	len = 4;
-	cmdp = &inquiry_result[0];
-
-	while (len--) {
+	for (i = 0; i < 4; i++) {
 		if (!wait_mask(STATUS(bse), DF, DF, 0, 0))
 			return 0;
-		*cmdp++ = inb(DATA(bse));
+		inquiry_result[i] = inb(DATA(bse));
 	}
 
 	/* Reading port should reset DF */
@@ -463,7 +459,6 @@ static int aha1542_queuecommand_lck(Scsi_Cmnd * SCpnt, void (*done) (Scsi_Cmnd *
 {
 	struct aha1542_hostdata *aha1542 = shost_priv(SCpnt->device->host);
 	u8 direction;
-	u8 *cmd = (u8 *) SCpnt->cmnd;
 	u8 target = SCpnt->device->id;
 	u8 lun = SCpnt->device->lun;
 	unsigned long flags;
@@ -480,28 +475,28 @@ static int aha1542_queuecommand_lck(Scsi_Cmnd * SCpnt, void (*done) (Scsi_Cmnd *
 	    }
 	);
 
-	if (*cmd == REQUEST_SENSE) {
+	if (*SCpnt->cmnd == REQUEST_SENSE) {
 		/* Don't do the command - we have the sense data already */
 		SCpnt->result = 0;
 		done(SCpnt);
 		return 0;
 	}
 #ifdef DEBUG
-	if (*cmd == READ_10 || *cmd == WRITE_10)
-		i = xscsi2int(cmd + 2);
-	else if (*cmd == READ_6 || *cmd == WRITE_6)
-		i = scsi2int(cmd + 2);
+	if (*SCpnt->cmnd == READ_10 || *SCpnt->cmnd == WRITE_10)
+		i = xscsi2int(SCpnt->cmnd + 2);
+	else if (*SCpnt->cmnd == READ_6 || *SCpnt->cmnd == WRITE_6)
+		i = scsi2int(SCpnt->cmnd + 2);
 	else
 		i = -1;
 	if (done)
-		printk(KERN_DEBUG "aha1542_queuecommand: dev %d cmd %02x pos %d len %d ", target, *cmd, i, bufflen);
+		printk(KERN_DEBUG "aha1542_queuecommand: dev %d cmd %02x pos %d len %d ", target, *SCpnt->cmnd, i, bufflen);
 	else
-		printk(KERN_DEBUG "aha1542_command: dev %d cmd %02x pos %d len %d ", target, *cmd, i, bufflen);
+		printk(KERN_DEBUG "aha1542_command: dev %d cmd %02x pos %d len %d ", target, *SCpnt->cmnd, i, bufflen);
 	printk(KERN_DEBUG "aha1542_queuecommand: dumping scsi cmd:");
 	for (i = 0; i < SCpnt->cmd_len; i++)
-		printk("%02x ", cmd[i]);
+		printk("%02x ", SCpnt->cmnd[i]);
 	printk("\n");
-	if (*cmd == WRITE_10 || *cmd == WRITE_6)
+	if (*SCpnt->cmnd == WRITE_10 || *SCpnt->cmnd == WRITE_6)
 		return 0;	/* we are still testing, so *don't* write */
 #endif
 	/* Use the outgoing mailboxes in a round-robin fashion, because this
@@ -540,12 +535,12 @@ static int aha1542_queuecommand_lck(Scsi_Cmnd * SCpnt, void (*done) (Scsi_Cmnd *
 	ccb[mbo].cdblen = SCpnt->cmd_len;
 
 	direction = 0;
-	if (*cmd == READ_10 || *cmd == READ_6)
+	if (*SCpnt->cmnd == READ_10 || *SCpnt->cmnd == READ_6)
 		direction = 8;
-	else if (*cmd == WRITE_10 || *cmd == WRITE_6)
+	else if (*SCpnt->cmnd == WRITE_10 || *SCpnt->cmnd == WRITE_6)
 		direction = 16;
 
-	memcpy(ccb[mbo].cdb, cmd, ccb[mbo].cdblen);
+	memcpy(ccb[mbo].cdb, SCpnt->cmnd, ccb[mbo].cdblen);
 
 	if (bufflen) {
 		struct scatterlist *sg;
@@ -617,15 +612,15 @@ static void setup_mailboxes(int bse, struct Scsi_Host *shpnt)
 	struct mailbox *mb = aha1542->mb;
 	struct ccb *ccb = aha1542->ccb;
 
-	u8 cmd[5] = { CMD_MBINIT, AHA1542_MAILBOXES, 0, 0, 0};
+	u8 mb_cmd[5] = { CMD_MBINIT, AHA1542_MAILBOXES, 0, 0, 0};
 
 	for (i = 0; i < AHA1542_MAILBOXES; i++) {
 		mb[i].status = mb[AHA1542_MAILBOXES + i].status = 0;
 		any2scsi(mb[i].ccbptr, isa_virt_to_bus(&ccb[i]));
 	};
 	aha1542_intr_reset(bse);	/* reset interrupts, so they don't block */
-	any2scsi((cmd + 2), isa_virt_to_bus(mb));
-	if (aha1542_out(bse, cmd, 5))
+	any2scsi((mb_cmd + 2), isa_virt_to_bus(mb));
+	if (aha1542_out(bse, mb_cmd, 5))
 		printk(KERN_ERR "aha1542_detect: failed setting up mailboxes\n");
 	aha1542_intr_reset(bse);
 }
-- 
Ondrej Zary


  parent reply	other threads:[~2015-02-06 22:16 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-02-06 22:11 [PATCH 0/36] aha1542: Various improvements Ondrej Zary
2015-02-06 22:11 ` [PATCH 01/36] aha1542: Stop using scsi_module.c Ondrej Zary
2015-02-06 22:11 ` [PATCH 02/36] aha1542: remove dead code Ondrej Zary
2015-02-06 22:11 ` [PATCH 03/36] aha1542: Remove SCSI_BUF_PA, SCSI_SG_PA, AHA1542_SCATTER and AHA1542_CMDLUN Ondrej Zary
2015-02-06 22:11 ` [PATCH 04/36] aha1542: Remove HOSTDATA macro Ondrej Zary
2015-02-06 22:11 ` [PATCH 05/36] aha1542: Convert aha1542_intr_reset to function Ondrej Zary
2015-02-06 22:11 ` [PATCH 06/36] aha1542: Use u8 instead of unchar Ondrej Zary
2015-02-06 22:11 ` [PATCH 07/36] aha1542: Reorder functions to remove forward declarations Ondrej Zary
2015-02-06 22:11 ` [PATCH 08/36] aha1542: remove empty aha1542_stat Ondrej Zary
2015-02-06 22:11 ` [PATCH 09/36] aha1542: Use BIT() macro Ondrej Zary
2015-02-06 22:11 ` [PATCH 10/36] aha1542: Remove WAIT and WAITd macros Ondrej Zary
2015-02-06 22:11 ` [PATCH 11/36] aha1542: Unify aha1542_in and aha1542_in1 Ondrej Zary
2015-02-06 22:11 ` [PATCH 12/36] aha1542: Split aha1542_out Ondrej Zary
2015-02-06 22:11 ` [PATCH 13/36] aha1542: Remove unneeded gotos Ondrej Zary
2015-02-06 22:11 ` [PATCH 14/36] aha1542: remove useless code from aha1542_test_port Ondrej Zary
2015-02-06 22:11 ` [PATCH 15/36] aha1542: Remove aha1542_restart Ondrej Zary
2015-02-06 22:11 ` [PATCH 16/36] aha1542: Merge aha1542_host_reset and aha1542_bus_reset Ondrej Zary
2015-02-06 22:11 ` [PATCH 17/36] aha1542: split out code from aha1542_hw_init Ondrej Zary
2015-02-06 22:11 ` [PATCH 18/36] aha1542: Call wait_mask from aha1542_out Ondrej Zary
2015-02-06 22:11 ` [PATCH 19/36] aha1542: rework hw_init Ondrej Zary
2015-02-06 22:11 ` [PATCH 20/36] aha1542: rework configuration parameters Ondrej Zary
2015-02-06 22:11 ` [PATCH 21/36] aha1542: Simplify aha1542_biosparam Ondrej Zary
2015-02-06 22:11 ` Ondrej Zary [this message]
2015-02-06 22:11 ` [PATCH 23/36] aha1524: Use struct scsi_cmnd Ondrej Zary
2015-02-06 22:11 ` [PATCH 24/36] aha1542: Always name Scsi_Host variables sh Ondrej Zary
2015-02-06 22:11 ` [PATCH 25/36] aha1542: fix include guard and remove useless changelog Ondrej Zary
2015-02-06 22:11 ` [PATCH 26/36] aha1542: " Ondrej Zary
2015-02-06 22:11 ` [PATCH 27/36] aha1542: cleanup includes Ondrej Zary
2015-02-06 22:11 ` [PATCH 28/36] aha1542: Pass struct Scsi_Host * to functions Ondrej Zary
2015-02-06 22:11 ` [PATCH 29/36] aha1542: Change aha1542_set_bus_times parameters Ondrej Zary
2015-02-06 22:11 ` [PATCH 30/36] aha1542: Use shost_printk instead of printk Ondrej Zary
2015-02-06 22:11 ` [PATCH 31/36] aha1542: remove DEB macro and simplify debug code Ondrej Zary
2015-02-06 22:11 ` [PATCH 32/36] aha1542: Use print_hex_dump_bytes in " Ondrej Zary
2015-02-06 22:11 ` [PATCH 33/36] aha1542: Don't reduce functionality with DEBUG enabled Ondrej Zary
2015-02-06 22:11 ` [PATCH 34/36] aha1542: rework locking Ondrej Zary
2015-02-06 22:11 ` [PATCH 35/36] aha1542: Fix bus reset Ondrej Zary
2015-02-06 22:11 ` [PATCH 36/36] aha1542: remove loop from aha1542_outb Ondrej Zary
2015-04-06 15:21 ` [PATCH 0/36] aha1542: Various improvements Christoph Hellwig

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1423260717-15944-23-git-send-email-linux@rainbow-software.org \
    --to=linux@rainbow-software.org \
    --cc=linux-scsi@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).