From: "Gerald Nowitzky" <Nowitzky@igne.de>
To: linux-driver@qlogic.com, linux-scsi@vger.kernel.org
Subject: Re: QLA2xxx on Dell M600
Date: Tue, 24 Feb 2009 11:37:13 +0100 [thread overview]
Message-ID: <167a01c9966b$daf18c20$0a00a8c0@ALDI2> (raw)
Here is the excerpt for the ql's from my lspci -vvv
09:00.0 Fibre Channel: QLogic Corp. ISP2432-based 4Gb Fibre Channel to PCI
Express HBA (rev 03)
Subsystem: QLogic Corp. Device 015b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at de3f8000 (64-bit, non-prefetchable) [size=16K]
Expansion ROM at de300000 [disabled] [size=256K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s
<4us, L1 <1us
ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 2048 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency
L0 <4us, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [64] Message Signalled Interrupts: Mask- 64bit+
Queue=0/4 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [74] Vital Product Data <?>
Capabilities: [7c] MSI-X: Enable- Mask- TabSize=16
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [138] Power Budgeting <?>
Kernel driver in use: qla2xxx
Kernel modules: qla2xxx
09:00.1 Fibre Channel: QLogic Corp. ISP2432-based 4Gb Fibre Channel to PCI
Express HBA (rev 03)
Subsystem: QLogic Corp. Device 015b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 6
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at de3fc000 (64-bit, non-prefetchable) [size=16K]
Expansion ROM at de500000 [disabled] [size=256K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [4c] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s
<4us, L1 <1us
ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency
L0 <4us, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [64] Message Signalled Interrupts: Mask- 64bit+
Queue=0/4 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [74] Vital Product Data <?>
Capabilities: [7c] MSI-X: Enable- Mask- TabSize=16
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [138] Power Budgeting <?>
Kernel modules: qla2xxx
----- Original Message -----
From: Gerald Nowitzky
To: linux-driver@qlogic.com ; linux-scsi@vger.kernel.org
Sent: Tuesday, February 24, 2009 11:30 AM
Subject: QLA2xxx on Dell M600
Hello!
I tried to use the qla2xxx on 2.6.28.7 with Dell Blade M600 and QME2472
Mezzanine Card, using x86 / 64 bit.
It OOPSes. The OOPS was introduced with 2.6.27.1 (qla2xxx 8.02.01-k7) . The
older 2.6.26.8 (qla2xxx 8.02.01-k4) works fine.
(Gerald)
[ 18.162122] QLogic Fibre Channel HBA Driver: 8.02.01-k9
[ 18.162180] qla2xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ
18
[ 18.162330] qla2xxx 0000:09:00.0: Found an ISP2432, irq 18, iobase
0xffffc200
1259c000
[ 18.162570] qla2xxx 0000:09:00.0: Configuring PCI space...
[ 18.162575] qla2xxx 0000:09:00.0: setting latency timer to 64
[ 18.195046] qla2xxx 0000:09:00.0: Configure NVRAM parameters...
[ 18.205078] usb usb2: suspend_rh (auto-stop)
[ 18.206352] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms
status 0x
301
[ 18.230605] BUG: unable to handle kernel NULL pointer dereference at
00000000
00000000
[ 18.231190] IP: [<ffffffff81230ce7>] strncpy+0x9/0x23
[ 18.231190] PGD 42bc2a067 PUD 42c139067 PMD 0
[ 18.231190] Oops: 0000 [#1] SMP
[ 18.231190] last sysfs file:
/sys/devices/pci0000:00/0000:00:03.0/0000:08:00.
0/host0/target0:1:0/0:1:0:0/type
[ 18.231190] CPU 3
[ 18.231190] Modules linked in: qla2xxx(+)
[ 18.231190] Pid: 1432, comm: modprobe Not tainted 2.6.28.7 #4
[ 18.231190] RIP: 0010:[<ffffffff81230ce7>] [<ffffffff81230ce7>]
strncpy+0x9/
0x23
[ 18.231190] RSP: 0018:ffff88042bccd9f8 EFLAGS: 00010202
[ 18.231190] RAX: 00000000000005b0 RBX: 0000000000000010 RCX:
ffff88042b83ab17
[ 18.231190] RDX: 000000000000004f RSI: 0000000000000000 RDI:
ffff88042b83ab17
[ 18.231190] RBP: ffff88042bccd9f8 R08: 0000000000000000 R09:
ffff88042c130000
[ 18.231190] R10: 0000000000000000 R11: ffff88042b838690 R12:
ffff88042b83ab06
[ 18.231190] R13: ffff88042b838690 R14: ffff88042d2851e0 R15:
0000000000000000
[ 18.231190] FS: 00007f95a58606f0(0000) GS:ffff88042e447700(0000)
knlGS:00000
00000000000
[ 18.231190] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 18.231190] CR2: 0000000000000000 CR3: 000000042c18d000 CR4:
00000000000006a0
[ 18.231190] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ 18.231190] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7:
0000000000000400
[ 18.231190] Process modprobe (pid: 1432, threadinfo ffff88042bccc000,
task ff
ff88042cef6cc0)
[ 18.231190] Stack:
[ 18.231190] ffff88042bccda28 ffffffffa0003376 ffff88042c130000
ffff88042b838
690
[ 18.231190] ffff88042d285000 ffff88042b838690 ffff88042bccda78
ffffffffa0006
764
[ 18.231190] ffff88042bccda78 ffffffffa0015a0f ffff88042c130000
ffff88042dcd9
1b0
[ 18.231190] Call Trace:
[ 18.231190] [<ffffffffa0003376>] qla2x00_set_model_info+0xec/0x121
[qla2xxx]
[ 18.231190] [<ffffffffa0006764>] qla24xx_nvram_config+0x2da/0x5f1
[qla2xxx]
[ 18.231190] [<ffffffffa0015a0f>] ? qla24xx_get_flash_version+0x1e5/0x296
[ql
a2xxx]
[ 18.231190] [<ffffffffa00071a7>] qla2x00_initialize_adapter+0x169/0x388
[qla
2xxx]
[ 18.231190] [<ffffffff81026697>] ? x86_swiotlb_alloc_coherent+0x1b/0x3c
[ 18.231190] [<ffffffffa001bd71>] qla2x00_probe_one+0xbac/0xefd [qla2xxx]
[ 18.231190] [<ffffffff810bba6d>] ? ifind+0x60/0x78
[ 18.231190] [<ffffffff810bb784>] ? iput+0x2f/0x65
[ 18.231190] [<ffffffff8102f720>] ? task_rq_lock+0x40/0x75
[ 18.231190] [<ffffffff8102f133>] ? task_rq_unlock+0xc/0xe
[ 18.231190] [<ffffffff81034eb9>] ? set_cpus_allowed_ptr+0x10a/0x117
[ 18.231190] [<ffffffff8123e0a0>] ? pci_match_id+0x1f/0x43
[ 18.231190] [<ffffffff8123e8f9>] pci_device_probe+0xb6/0x10f
[ 18.231190] [<ffffffff810f802b>] ? sysfs_create_link+0xe/0x13
[ 18.231190] [<ffffffff812bf922>] driver_probe_device+0xd9/0x169
[ 18.231190] [<ffffffff812bfa14>] __driver_attach+0x62/0x8c
[ 18.231190] [<ffffffff812bf9b2>] ? __driver_attach+0x0/0x8c
[ 18.231190] [<ffffffff812bf9b2>] ? __driver_attach+0x0/0x8c
[ 18.231190] [<ffffffff812bf1a0>] bus_for_each_dev+0x4a/0x79
[ 18.246322] [<ffffffff812bf753>] driver_attach+0x1c/0x1e
[ 18.246322] [<ffffffff812beaf2>] bus_add_driver+0xb5/0x207
[ 18.246322] [<ffffffff812bfca3>] driver_register+0x93/0x10a
[ 18.246322] [<ffffffffa0030000>] ? qla2x00_module_init+0x0/0x131
[qla2xxx]
[ 18.246322] [<ffffffff8123eb9e>] __pci_register_driver+0x63/0x9d
[ 18.246322] [<ffffffffa0030000>] ? qla2x00_module_init+0x0/0x131
[qla2xxx]
[ 18.246322] [<ffffffffa0030101>] qla2x00_module_init+0x101/0x131
[qla2xxx]
[ 18.246322] [<ffffffff81009058>] _stext+0x58/0x139
[ 18.246322] [<ffffffff81021eb2>] ? __send_IPI_dest_field+0x5c/0x64
[ 18.246322] [<ffffffff8101a652>] ? native_smp_send_reschedule+0x3b/0x3d
[ 18.246322] [<ffffffff8102d438>] ? smp_send_reschedule+0xa/0xc
[ 18.246322] [<ffffffff8102ee65>] ? resched_task+0x7b/0x7f
[ 18.246322] [<ffffffff8102f133>] ? task_rq_unlock+0xc/0xe
[ 18.246322] [<ffffffff81032b09>] ? try_to_wake_up+0x218/0x22a
[ 18.246322] [<ffffffff8105d8da>] sys_init_module+0x9f/0x1ad
[ 18.246322] [<ffffffff8100bf6b>] system_call_fastpath+0x16/0x1b
[ 18.246322] Code: ff e9 29 ff ff ff 90 90 55 48 89 fa 48 89 e5 8a 06 48
ff c6
88 02 48 ff c2 84 c0 75 f2 c9 48 89 f8 c3 55 48 89 f9 48 89 e5 eb 10 <8a>
06 3c
01 88 01 48 83 de ff 48 ff c1 48 ff ca 48 85 d2 75 eb
[ 18.246322] RIP [<ffffffff81230ce7>] strncpy+0x9/0x23
[ 18.246322] RSP <ffff88042bccd9f8>
[ 18.246322] CR2: 0000000000000000
[ 18.255936] ---[ end trace 2127ef5a187ff23f ]---
[ 18.257613] modprobe used greatest stack depth: 4128 bytes left
next reply other threads:[~2009-02-24 10:37 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-02-24 10:37 Gerald Nowitzky [this message]
-- strict thread matches above, loose matches on Subject: below --
2009-02-24 11:00 QLA2xxx on Dell M600 Gerald Nowitzky
[not found] <166d01c9966a$f0d6f990$0a00a8c0@ALDI2>
2009-02-24 15:49 ` Andrew Vasquez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='167a01c9966b$daf18c20$0a00a8c0@ALDI2' \
--to=nowitzky@igne.de \
--cc=linux-driver@qlogic.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox