From: "Michael W. Shaffer" <mwshaffer@yahoo.com>
To: Andrew Vasquez <praka@users.sourceforge.net>
Cc: linux-scsi@vger.kernel.org
Subject: Re: No LUNs detected with 2.6.1-mm4 qla2xxx / qla2300
Date: Mon, 19 Jan 2004 08:09:58 -0800 (PST) [thread overview]
Message-ID: <20040119160958.60827.qmail@web10407.mail.yahoo.com> (raw)
In-Reply-To: <20040119052701.GA16779@praka.local.home>
Ok, I don't know if this was the 'right' fix, but I noticed
that the Kconfig file in the qla2xxx directory was different
in the -b9 resync patchset, so I tried copying the old one
back from the plain 2.6.1-mm4 tree, and now I got the
modules built and installed. After enabling debugging and
rebooting -- we now have LUNs! Attached is the output from
/var/log/messages showing the -b9 module loading and finding
the Nexsan arrays and their associated disk volumes. There
are supposed to be two LUNs per array as shown, and now I
have disk devices /dev/sdb - /dev/sde as expected. The
unknown partition table comments are correct also, since
I'm using the raw devices without any partitioning as
members of RAID1 mirror sets.
A couple of minor points:
- It appears that the patched driver still reports itself
as v8.00.00b8-debug, rather than b9.
- Someone noted this on the list before I think, but I also
noticed it: when you unload and re-load the qla2300 module,
it appears to not be decrementing some counter. The first
time, you get /proc/scsi/qla2xxx/2 and /proc/scsi/qla2xxx/3,
and the second time you get /4 and /5, and so forth, each
time you re-load. The logical names of the scsi devices
are not affected, just the numbers in the /proc/scsi/qla2xxx
directory.
/var/log/messages
-----------------------------------------------------------
Jan 19 07:55:14 thing2 kernel: QLogic Fibre Channel HBA Driver (f88bd000)
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: Found an ISP2312, irq
25, iobase 0xf8895000
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: Configuring PCI
space...
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: Configure NVRAM
parameters...
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: Verifying loaded RISC
code...
Jan 19 07:55:20 thing2 kernel: scsi(2): **** Load RISC code ****
Jan 19 07:55:20 thing2 kernel: scsi(2): Verifying Checksum of loaded RISC
code.
Jan 19 07:55:20 thing2 kernel: scsi(2): Checksum OK, start firmware.
Jan 19 07:55:20 thing2 kernel: scsi(2): Issue init firmware.
Jan 19 07:55:20 thing2 kernel: scsi(2): Asynchronous LIP RESET (f8f7).
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: LIP reset occured
(f8f7).
Jan 19 07:55:20 thing2 kernel: qla2300 0000:01:02.0: Waiting for LIP to
complete...
Jan 19 07:55:21 thing2 kernel: scsi(2): LIP occured (f8f7).
Jan 19 07:55:21 thing2 kernel: qla2300 0000:01:02.0: LIP occured (f8f7).
Jan 19 07:55:21 thing2 kernel: scsi(2): Asynchronous LOOP UP (2 Gbps).
Jan 19 07:55:21 thing2 kernel: qla2300 0000:01:02.0: LOOP UP detected (2
Gbps).
Jan 19 07:55:21 thing2 kernel: scsi(2): Asynchronous PORT UPDATE.
Jan 19 07:55:21 thing2 kernel: scsi(2): Port database changed ffff 0006.
Jan 19 07:55:21 thing2 kernel: scsi(2): F/W Ready - OK
Jan 19 07:55:21 thing2 kernel: scsi(2): fw_state=3 curr time=fffe433e.
Jan 19 07:55:21 thing2 kernel: qla2300 0000:01:02.0: Topology - (Loop), Host
Loop address 0x1
Jan 19 07:55:21 thing2 kernel: scsi(2): Configure loop -- dpc flags =0x80040
Jan 19 07:55:22 thing2 kernel: qla2x00_mailbox_command(2): **** FAILED.
mbx0=4006, mbx1=7e, mbx2=0, cmd=6a ****
Jan 19 07:55:22 thing2 kernel: qla2x00_get_port_name(2): failed=102.
Jan 19 07:55:22 thing2 kernel: scsi(2): MBC_GET_PORT_NAME Failed, No FL Port
Jan 19 07:55:22 thing2 kernel: scsi(2): Alloc Target 0 @ f7a4b800
Jan 19 07:55:22 thing2 kernel: scsi(2): Assigning target ID=00 @ f7a4b800 to
loop id=0x0000, port state=0x4, port down retry=60
Jan 19 07:55:22 thing2 kernel: scsi(2): Alloc Lun 0 @ tgt 0.
Jan 19 07:55:22 thing2 kernel: scsi(2): Alloc Lun 1 @ tgt 0.
Jan 19 07:55:22 thing2 kernel: scsi(2): LOOP READY
Jan 19 07:55:22 thing2 kernel: DEBUG: detect hba 2 at address = f6c9c1b8
Jan 19 07:55:22 thing2 kernel: scsi2 : qla2xxx
Jan 19 07:55:22 thing2 kernel: qla2300 0000:01:02.0:
Jan 19 07:55:22 thing2 kernel: QLogic Fibre Channel HBA Driver:
8.00.00b8-debug
Jan 19 07:55:22 thing2 kernel: QLogic QLA2340 -
Jan 19 07:55:22 thing2 kernel: ISP2312: PCI (66 MHz) @ 0000:01:02.0 hdma-,
host#=2, fw=3.02.20 IPX
Jan 19 07:55:22 thing2 kernel: Vendor: NEXSAN Model: ATAboy(821DFC56)
Rev: 5020
Jan 19 07:55:22 thing2 kernel: Type: Direct-Access
ANSI SCSI revision: 04
Jan 19 07:55:22 thing2 kernel: qla2300 0000:01:02.0: scsi(2:0:0:0): Enabled
tagged queuing, queue depth 32.
Jan 19 07:55:23 thing2 kernel: SCSI device sdb: 3904296875 512-byte hdwr
sectors (1999000 MB)
Jan 19 07:55:23 thing2 kernel: SCSI device sdb: drive cache: write back
Jan 19 07:55:23 thing2 kernel: sdb: unknown partition table
Jan 19 07:55:23 thing2 kernel: Attached scsi disk sdb at scsi2, channel 0,
id 0, lun 0
Jan 19 07:55:23 thing2 kernel: Attached scsi generic sg2 at scsi2, channel
0, id 0, lun 0, type 0
Jan 19 07:55:23 thing2 kernel: scsi(2:0:0) UNDERRUN status detected
0x15-0x800.
Jan 19 07:55:23 thing2 kernel: Vendor: NEXSAN Model: ATAboy(821DFC56)
Rev: 5020
Jan 19 07:55:23 thing2 kernel: Type: Direct-Access
ANSI SCSI revision: 04
Jan 19 07:55:23 thing2 kernel: qla2300 0000:01:02.0: scsi(2:0:0:1): Enabled
tagged queuing, queue depth 32.
Jan 19 07:55:23 thing2 kernel: SCSI device sdc: 196367187 512-byte hdwr
sectors (100540 MB)
Jan 19 07:55:23 thing2 kernel: SCSI device sdc: drive cache: write back
Jan 19 07:55:23 thing2 kernel: sdc: unknown partition table
Jan 19 07:55:23 thing2 kernel: Attached scsi disk sdc at scsi2, channel 0,
id 0, lun 1
Jan 19 07:55:23 thing2 kernel: Attached scsi generic sg3 at scsi2, channel
0, id 0, lun 1, type 0
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: Found an ISP2312, irq
25, iobase 0xf889b000
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: Configuring PCI
space...
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: Configure NVRAM
parameters...
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: Verifying loaded RISC
code...
Jan 19 07:55:24 thing2 kernel: scsi(3): **** Load RISC code ****
Jan 19 07:55:24 thing2 kernel: scsi(3): Verifying Checksum of loaded RISC
code.
Jan 19 07:55:24 thing2 kernel: scsi(3): Checksum OK, start firmware.
Jan 19 07:55:24 thing2 kernel: scsi(3): Issue init firmware.
Jan 19 07:55:24 thing2 kernel: scsi(3): Asynchronous LIP RESET (f8f7).
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: LIP reset occured
(f8f7).
Jan 19 07:55:24 thing2 kernel: qla2300 0000:01:03.0: Waiting for LIP to
complete...
Jan 19 07:55:25 thing2 kernel: scsi(3): LIP occured (f8f7).
Jan 19 07:55:25 thing2 kernel: qla2300 0000:01:03.0: LIP occured (f8f7).
Jan 19 07:55:25 thing2 kernel: scsi(3): Asynchronous LOOP UP (2 Gbps).
Jan 19 07:55:25 thing2 kernel: qla2300 0000:01:03.0: LOOP UP detected (2
Gbps).
Jan 19 07:55:25 thing2 kernel: scsi(3): Asynchronous PORT UPDATE.
Jan 19 07:55:25 thing2 kernel: scsi(3): Port database changed ffff 0006.
Jan 19 07:55:25 thing2 kernel: scsi(3): F/W Ready - OK
Jan 19 07:55:25 thing2 kernel: scsi(3): fw_state=3 curr time=fffe51b1.
Jan 19 07:55:25 thing2 kernel: qla2300 0000:01:03.0: Topology - (Loop), Host
Loop address 0x1
Jan 19 07:55:25 thing2 kernel: scsi(3): Configure loop -- dpc flags =0x80040
Jan 19 07:55:25 thing2 kernel: qla2x00_mailbox_command(3): **** FAILED.
mbx0=4006, mbx1=7e, mbx2=0, cmd=6a ****
Jan 19 07:55:25 thing2 kernel: qla2x00_get_port_name(3): failed=102.
Jan 19 07:55:25 thing2 kernel: scsi(3): MBC_GET_PORT_NAME Failed, No FL Port
Jan 19 07:55:25 thing2 kernel: scsi(3): Alloc Target 0 @ f6cf1800
Jan 19 07:55:25 thing2 kernel: scsi(3): Assigning target ID=00 @ f6cf1800 to
loop id=0x0000, port state=0x4, port down retry=60
Jan 19 07:55:26 thing2 kernel: scsi(3): Alloc Lun 0 @ tgt 0.
Jan 19 07:55:26 thing2 kernel: scsi(3): Alloc Lun 1 @ tgt 0.
Jan 19 07:55:26 thing2 kernel: scsi(3): LOOP READY
Jan 19 07:55:26 thing2 kernel: DEBUG: detect hba 3 at address = f6bf01b8
Jan 19 07:55:26 thing2 kernel: scsi3 : qla2xxx
Jan 19 07:55:26 thing2 kernel: qla2300 0000:01:03.0:
Jan 19 07:55:26 thing2 kernel: QLogic Fibre Channel HBA Driver:
8.00.00b8-debug
Jan 19 07:55:26 thing2 kernel: QLogic QLA2340 -
Jan 19 07:55:26 thing2 kernel: ISP2312: PCI (66 MHz) @ 0000:01:03.0 hdma-,
host#=3, fw=3.02.20 IPX
Jan 19 07:55:26 thing2 kernel: Vendor: NEXSAN Model: ATAboy(821DFC55)
Rev: 5020
Jan 19 07:55:26 thing2 kernel: Type: Direct-Access
ANSI SCSI revision: 04
Jan 19 07:55:26 thing2 kernel: qla2300 0000:01:03.0: scsi(3:0:0:0): Enabled
tagged queuing, queue depth 32.
Jan 19 07:55:26 thing2 kernel: SCSI device sdd: 3904296875 512-byte hdwr
sectors (1999000 MB)
Jan 19 07:55:26 thing2 kernel: SCSI device sdd: drive cache: write back
Jan 19 07:55:26 thing2 kernel: sdd: unknown partition table
Jan 19 07:55:26 thing2 kernel: Attached scsi disk sdd at scsi3, channel 0,
id 0, lun 0
Jan 19 07:55:26 thing2 kernel: Attached scsi generic sg4 at scsi3, channel
0, id 0, lun 0, type 0
Jan 19 07:55:27 thing2 kernel: scsi(3:0:0) UNDERRUN status detected
0x15-0x800.
Jan 19 07:55:27 thing2 kernel: Vendor: NEXSAN Model: ATAboy(821DFC55)
Rev: 5020
Jan 19 07:55:27 thing2 kernel: Type: Direct-Access
ANSI SCSI revision: 04
Jan 19 07:55:27 thing2 kernel: qla2300 0000:01:03.0: scsi(3:0:0:1): Enabled
tagged queuing, queue depth 32.
Jan 19 07:55:27 thing2 kernel: SCSI device sde: 196367187 512-byte hdwr
sectors (100540 MB)
Jan 19 07:55:27 thing2 kernel: SCSI device sde: drive cache: write back
Jan 19 07:55:27 thing2 kernel: sde: unknown partition table
Jan 19 07:55:27 thing2 kernel: Attached scsi disk sde at scsi3, channel 0,
id 0, lun 1
Jan 19 07:55:27 thing2 kernel: Attached scsi generic sg5 at scsi3, channel
0, id 0, lun 1, type 0
----------------------------------------------------
__________________________________
Do you Yahoo!?
Yahoo! Hotjobs: Enter the "Signing Bonus" Sweepstakes
http://hotjobs.sweepstakes.yahoo.com/signingbonus
next prev parent reply other threads:[~2004-01-19 16:09 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-01-18 23:25 No LUNs detected with 2.6.1-mm4 qla2xxx / qla2300 Michael W. Shaffer
2004-01-19 5:27 ` Andrew Vasquez
2004-01-19 6:36 ` Michael W. Shaffer
2004-01-19 8:24 ` Michael W. Shaffer
2004-01-19 16:09 ` Michael W. Shaffer [this message]
-- strict thread matches above, loose matches on Subject: below --
2004-01-19 16:55 Andrew Vasquez
2004-01-19 17:06 ` James Bottomley
2004-01-19 17:38 Andrew Vasquez
2004-01-19 21:42 ` Michael W. Shaffer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040119160958.60827.qmail@web10407.mail.yahoo.com \
--to=mwshaffer@yahoo.com \
--cc=linux-scsi@vger.kernel.org \
--cc=praka@users.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox