* Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-05 16:50 Stefan Berder
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Berder @ 2005-01-05 16:50 UTC (permalink / raw)
To: linux-scsi
[-- Attachment #1: Type: text/plain, Size: 1653 bytes --]
Hi all,
I got some strange problems with the megaraid driver under linux.
The box I'm running is a dell poweredge 6450 with a PERC3/DC raid
controller and Adaptec AIC-7899P controllers. I got 2x36GB (RAID1) scsi
hdd inside the box an 13x36GB (RAID5) in a dell hdd bay, debian sarge is
the system.
I got various problems :
- I found a debian install iso on the linux.dell;com site to install the
box. It's a 2.4.28 kernel, and the box is working fine with this kernel.
When I switch to a 2.4.28 kernel based on the configuration file
provided with the install kernel and removing some useless things,
adding netfilter, the box boots but hdds got really poor performances :
brucelee:~/src# hdparm -t -T /dev/sda /dev/sdb
/dev/sda:
Timing cached reads: 724 MB in 2.00 seconds = 362.00 MB/sec
Timing buffered disk reads: 12 MB in 3.56 seconds = 3.37 MB/sec
/dev/sdb:
Timing cached reads: 668 MB in 2.00 seconds = 334.00 MB/sec
Timing buffered disk reads: 12 MB in 3.19 seconds = 3.76 MB/sec
- When I compile a 2.6.10 kernel, I got 2 problems, first when I use the
megaraid legacy I get a kernel panic during boot with something about
"data cache" before. When I use the new megaraid (megaraid_mm and
megaraid_mbox) during the kernel scsi probe it says that some command
hangs and timeouts, then it does a lot of timeouts...
lspci and dmesg attached
--
#=- Stefan Berder tel : 6 14 80 -=#
#=- Ingénieur système et réseau 01 53 95 14 80 -=#
#=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
#=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 10722 bytes --]
brucelee:~/src# lspci -vx
0000:00:00.0 Host bridge: ServerWorks CNB20HE Host Bridge (rev 21)
Flags: fast devsel
00: 66 11 08 00 00 00 00 00 21 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:00.1 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01)
Flags: bus master, medium devsel, latency 32
00: 66 11 08 00 47 01 00 22 01 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
0000:00:00.2 Host bridge: ServerWorks CNB20HE Host Bridge
Flags: medium devsel
00: 66 11 06 00 42 01 00 22 00 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:00.3 Host bridge: ServerWorks CNB20HE Host Bridge
Flags: medium devsel
00: 66 11 06 00 42 01 00 22 00 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:04.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC (rev 7a) (prog-if 00 [VGA])
Subsystem: Dell: Unknown device 00a2
Flags: bus master, VGA palette snoop, stepping, medium devsel, latency 32
Memory at fc000000 (32-bit, prefetchable) [size=16M]
I/O ports at ec00 [size=256]
Memory at fbeff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 1
00: 02 10 59 47 a7 00 90 02 7a 00 00 03 08 20 00 00
10: 08 00 00 fc 01 ec 00 00 00 f0 ef fb 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 00 00 5c 00 00 00 00 00 00 00 ff 00 08 00
0000:00:05.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Dell: Unknown device 00a2
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
BIST result: 00
I/O ports at e800 [disabled] [size=256]
Memory at fbefe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00: 05 90 cf 00 16 01 b0 02 01 00 00 01 08 20 80 80
10: 01 e8 00 00 04 e0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 f0 fb dc 00 00 00 00 00 00 00 0b 01 28 19
0000:00:05.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Dell: Unknown device 00a2
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
BIST result: 00
I/O ports at e400 [disabled] [size=256]
Memory at fbefd000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00: 05 90 cf 00 16 01 b0 02 01 00 00 01 08 20 80 80
10: 01 e4 00 00 04 d0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 f0 fb dc 00 00 00 00 00 00 00 0a 02 28 19
0000:00:07.0 System peripheral: American Megatrends Inc. MegaRAC (rev 04)
Subsystem: American Megatrends Inc. Dell Remote Assistant Card 2
Flags: bus master, medium devsel, latency 32, IRQ 21
BIST result: 00
I/O ports at e080 [size=128]
Memory at fbefc000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=16K]
00: 1e 10 63 90 17 01 00 02 04 00 80 08 08 20 00 80
10: 81 e0 00 00 00 c0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 67 07
30: 00 00 f0 fb 00 00 00 00 00 00 00 00 05 01 00 00
0000:00:08.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Dell PowerEdge 2550
Flags: bus master, medium devsel, latency 32, IRQ 26
Memory at fbefb000 (32-bit, non-prefetchable) [size=4K]
I/O ports at e040 [size=64]
Memory at fbd00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 20 00 00
10: 00 b0 ef fb 41 e0 00 00 00 00 d0 fb 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 9b 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 08 38
0000:00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 50)
Subsystem: ServerWorks OSB4 South Bridge
Flags: bus master, medium devsel, latency 0
00: 66 11 00 02 07 00 00 02 50 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 00 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at 08b0 [size=16]
00: 66 11 11 02 05 00 00 02 00 8a 01 01 00 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: b1 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: ServerWorks OSB4/CSB5 OHCI USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 31
Memory at fbefa000 (32-bit, non-prefetchable) [size=4K]
00: 66 11 20 02 17 01 80 02 04 10 03 0c 08 20 80 00
10: 00 a0 ef fb 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 20 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 50
0000:03:09.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 32
Bus: primary=03, secondary=04, subordinate=05, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: faa00000-facfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
Capabilities: [dc] Power Management version 1
00: 11 10 26 00 07 01 b0 02 05 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 03 04 05 20 c1 c1 80 22
20: a0 fa c0 fa 01 f0 f1 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:03:0a.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 32
Bus: primary=03, secondary=06, subordinate=07, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fa700000-fa9fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000eff00000
Capabilities: [dc] Power Management version 1
00: 86 80 54 b1 07 01 b0 02 00 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 03 06 07 20 b1 b1 80 22
20: 70 fa 90 fa 01 e8 f1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:03:0b.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Server Adapter (PILA8470B)
Flags: bus master, medium devsel, latency 32, IRQ 25
Memory at fa5ff000 (32-bit, non-prefetchable) [size=4K]
I/O ports at acc0 [size=64]
Memory at fa400000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 20 00 00
10: 00 f0 5f fa c1 ac 00 00 00 00 40 fa 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 0c 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 08 38
0000:04:00.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=04, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fac00000-facfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
Capabilities: [dc] Power Management version 1
00: 11 10 26 00 07 01 90 02 05 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 04 05 05 20 f1 01 80 22
20: c0 fa c0 fa 01 f0 f1 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:04:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3 SCSI Processor (rev 06)
Subsystem: American Megatrends Inc. QLA12160 on AMI MegaRAID
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 27
I/O ports at cc00 [size=256]
Memory at faaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fab00000 [disabled] [size=128K]
Capabilities: [44] Power Management version 1
00: 77 10 16 12 17 01 b0 02 06 00 00 01 08 20 00 00
10: 01 cc 00 00 00 f0 af fa 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 93 84
30: 00 00 b0 fa 44 00 00 00 00 00 00 00 0b 01 40 00
0000:05:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20)
Subsystem: Dell PowerEdge RAID Controller 3/DC
Flags: bus master, medium devsel, latency 32, IRQ 23
Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fac00000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
00: 1e 10 60 19 16 01 90 02 20 00 04 01 08 20 00 00
10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 93 04
30: 00 00 c0 fa 80 00 00 00 00 00 00 00 0a 01 00 00
0000:06:00.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=06, secondary=07, subordinate=07, sec-latency=32
Memory behind bridge: fa900000-fa9fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000eff00000
Capabilities: [dc] Power Management version 1
00: 86 80 54 b1 07 01 90 02 00 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 06 07 07 20 f1 01 80 22
20: 90 fa 90 fa 01 e8 f1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:06:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3 SCSI Processor (rev 06)
Subsystem: American Megatrends Inc. QLA12160 on AMI MegaRAID
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 28
I/O ports at bc00 [size=256]
Memory at fa7ff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fa800000 [disabled] [size=128K]
Capabilities: [44] Power Management version 1
00: 77 10 16 12 17 01 b0 02 06 00 00 01 08 20 00 00
10: 01 bc 00 00 00 f0 7f fa 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 93 84
30: 00 00 80 fa 44 00 00 00 00 00 00 00 05 01 40 00
0000:07:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20)
Subsystem: Dell PowerEdge RAID Controller 3/DC
Flags: bus master, medium devsel, latency 32, IRQ 24
Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fa900000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
00: 1e 10 60 19 16 01 90 02 20 00 04 01 08 20 00 00
10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 93 04
30: 00 00 90 fa 80 00 00 00 00 00 00 00 0b 01 00 00
[-- Attachment #3: dmesg.txt --]
[-- Type: text/plain, Size: 15184 bytes --]
brucelee:~/src# dmesg
Linux version 2.4.28-bruce2.4 (root@brucelee) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 SMP Wed Jan 5 13:39:01 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003fffe000 (usable)
BIOS-e820: 000000003fffe000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 262142
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32766 pages.
ACPI: RSDP (v000 DELL ) @ 0x000fdcb0
ACPI: RSDT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdcc4
ACPI: FADT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdcf0
ACPI: MADT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdd64
ACPI: DSDT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 Pentium(tm) Pro APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 17
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: POWEREDGE A2 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
I/O APIC #3 Version 17 at 0xFEC01000.
Enabling APIC mode: Flat. Using 2 I/O APICs
Processors: 2
Kernel command line: auto BOOT_IMAGE=Linux ro root=802
Initializing CPU#0
Detected 699.336 MHz processor.
Console: colour VGA+ 80x50
Calibrating delay loop... 1395.91 BogoMIPS
Memory: 1032112k/1048568k available (2290k kernel code, 16072k reserved, 758k data, 132k init, 131064k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2923.06 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1395.91 BogoMIPS
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Cascades) stepping 01
Total of 2 processors activated (2791.83 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-2, 2-5, 2-10, 2-11, 2-13 not connected.
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 48.
number of IO-APIC #2 registers: 16.
number of IO-APIC #3 registers: 16.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 000 00 1 0 0 0 0 0 0 00
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 0D000000
....... : arbitration: 0D
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 1 1 0 1 0 1 1 89
01 003 03 1 1 0 1 0 1 1 91
02 003 03 1 1 0 1 0 1 1 99
03 003 03 1 1 0 1 0 1 1 A1
04 003 03 1 1 0 1 0 1 1 A9
05 003 03 1 1 0 1 0 1 1 B1
06 003 03 1 1 0 1 0 1 1 B9
07 003 03 1 1 0 1 0 1 1 C1
08 003 03 1 1 0 1 0 1 1 C9
09 003 03 1 1 0 1 0 1 1 D1
0a 003 03 1 1 0 1 0 1 1 D9
0b 003 03 1 1 0 1 0 1 1 E1
0c 003 03 1 1 0 1 0 1 1 E9
0d 003 03 1 1 0 1 0 1 1 32
0e 003 03 1 1 0 1 0 1 1 3A
0f 003 03 1 1 0 1 0 1 1 42
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 1:0
IRQ17 -> 1:1
IRQ18 -> 1:2
IRQ19 -> 1:3
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ22 -> 1:6
IRQ23 -> 1:7
IRQ24 -> 1:8
IRQ25 -> 1:9
IRQ26 -> 1:10
IRQ27 -> 1:11
IRQ28 -> 1:12
IRQ29 -> 1:13
IRQ30 -> 1:14
IRQ31 -> 1:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 699.2856 MHz.
..... host bus clock speed is 99.8976 MHz.
cpu: 0, clocks: 998976, slice: 332992
CPU0<T0:998976,T1:665984,D:0,S:332992,C:998976>
cpu: 1, clocks: 998976, slice: 332992
CPU1<T0:998976,T1:332992,D:0,S:332992,C:998976>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfc7ee, last bus=16
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Discovered primary peer bus 03 [IRQ]
PCI: Discovered primary peer bus 10 [IRQ]
PCI: Using IRQ router ServerWorks [1166/0200] at 00:0f.0
PCI->APIC IRQ transform: (B0,I5,P0) -> 17
PCI->APIC IRQ transform: (B0,I5,P1) -> 18
PCI->APIC IRQ transform: (B0,I7,P0) -> 21
PCI->APIC IRQ transform: (B0,I8,P0) -> 26
PCI->APIC IRQ transform: (B0,I15,P0) -> 31
PCI->APIC IRQ transform: (B3,I11,P0) -> 25
PCI->APIC IRQ transform: (B4,I1,P0) -> 27
PCI->APIC IRQ transform: (B5,I0,P0) -> 23
PCI->APIC IRQ transform: (B6,I1,P0) -> 28
PCI->APIC IRQ transform: (B7,I0,P0) -> 24
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
HP CISS Driver (v 2.4.52)
Intel(R) PRO/100 Network Driver - version 2.3.43-k1
Copyright (c) 2004 Intel Corporation
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
cpu cycle saver enabled
e100: selftest OK.
e100: eth1: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
cpu cycle saver enabled
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: no supported devices found.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] Initialized radeon 1.7.0 20020828 on minor 1
[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:pio, hdd:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
megaraid: v2.10.3 (Release Date: Thu Apr 8 16:16:05 EDT 2004)
megaraid: found 0x101e:0x1960:bus 5:slot 0:func 0
scsi2:Found MegaRAID controller at 0xf8808000, IRQ:23
megaraid: [1.57:3.13] detected 2 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: found 0x101e:0x1960:bus 7:slot 0:func 0
scsi3:Found MegaRAID controller at 0xf880a000, IRQ:24
megaraid: [161J:3.17] detected 0 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: Cluster driver, initiator id:14
scsi2 : LSI Logic MegaRAID 1.57 254 commands 16 targs 5 chans 7 luns
scsi3 : LSI Logic MegaRAID 161J 254 commands 16 targs 5 chans 7 luns
scsi2: scanning scsi channel 0 for logical drives.
Vendor: MegaRAID Model: LD0 RAID1 34678R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
Vendor: MegaRAID Model: LD1 RAID5 46780R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
scsi2: scanning scsi channel 1 for logical drives.
scsi2: scanning scsi channel 2 for logical drives.
scsi2: scanning scsi channel 4 [P0] for physical devices.
Vendor: DELL Model: 1x4 U2W SCSI BP Rev: 1.27
Type: Processor ANSI SCSI revision: 02
scsi2: scanning scsi channel 5 [P1] for physical devices.
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
scsi3: scanning scsi channel 0 for logical drives.
scsi3: scanning scsi channel 1 for logical drives.
scsi3: scanning scsi channel 2 for logical drives.
scsi3: scanning scsi channel 4 [P0] for physical devices.
scsi3: scanning scsi channel 5 [P1] for physical devices.
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi2, channel 0, id 1, lun 0
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
Partition check:
sda: sda1 sda2
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: sdb1
es1371: version v0.32 time 13:43:04 Jan 5 2005
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xf880c000, IRQ 31
host/usb-ohci.c: usb-00:0f.2, ServerWorks OSB4/CSB5 OHCI USB Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 152 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ds: no socket drivers loaded!
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding Swap: 1000424k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04Aborted Command
e100: eth0 NIC Link is Up 100 Mbps Full duplex
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-05 17:07 Mukker, Atul
2005-01-05 18:08 ` Stefan Berder
0 siblings, 1 reply; 10+ messages in thread
From: Mukker, Atul @ 2005-01-05 17:07 UTC (permalink / raw)
To: 'Stefan Berder', 'linux-scsi@vger.kernel.org'
Please attach the dmesg output from the megaraid_mm and megaraid_mbox
drivers as well. Also, all files from /proc/megaraid2 directory from 2.4
kernel driver
Thanks
-Atul Mukker
LSI Logic Corporation
> -----Original Message-----
> From: Stefan Berder [mailto:sbe@oleane.net]
> Sent: Wednesday, January 05, 2005 11:50 AM
> To: linux-scsi@vger.kernel.org
> Subject: Problem with megaraid and PERC3/dc on a poweredge 6450
>
> Hi all,
> I got some strange problems with the megaraid driver under linux.
> The box I'm running is a dell poweredge 6450 with a PERC3/DC
> raid controller and Adaptec AIC-7899P controllers. I got
> 2x36GB (RAID1) scsi hdd inside the box an 13x36GB (RAID5) in
> a dell hdd bay, debian sarge is the system.
>
> I got various problems :
> - I found a debian install iso on the linux.dell;com site to
> install the box. It's a 2.4.28 kernel, and the box is working
> fine with this kernel.
> When I switch to a 2.4.28 kernel based on the configuration
> file provided with the install kernel and removing some
> useless things, adding netfilter, the box boots but hdds got
> really poor performances :
> brucelee:~/src# hdparm -t -T /dev/sda /dev/sdb
>
> /dev/sda:
> Timing cached reads: 724 MB in 2.00 seconds = 362.00 MB/sec
> Timing buffered disk reads: 12 MB in 3.56 seconds = 3.37 MB/sec
>
> /dev/sdb:
> Timing cached reads: 668 MB in 2.00 seconds = 334.00 MB/sec
> Timing buffered disk reads: 12 MB in 3.19 seconds = 3.76 MB/sec
>
> - When I compile a 2.6.10 kernel, I got 2 problems, first
> when I use the megaraid legacy I get a kernel panic during
> boot with something about "data cache" before. When I use the
> new megaraid (megaraid_mm and
> megaraid_mbox) during the kernel scsi probe it says that some
> command hangs and timeouts, then it does a lot of timeouts...
>
> lspci and dmesg attached
> --
> #=- Stefan Berder tel : 6 14 80 -=#
> #=- Ingénieur système et réseau 01 53 95 14 80 -=#
> #=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
> #=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Problem with megaraid and PERC3/dc on a poweredge 6450
2005-01-05 17:07 Mukker, Atul
@ 2005-01-05 18:08 ` Stefan Berder
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Berder @ 2005-01-05 18:08 UTC (permalink / raw)
To: Mukker, Atul; +Cc: 'linux-scsi@vger.kernel.org'
[-- Attachment #1: Type: text/plain, Size: 618 bytes --]
On Wed, 5 Jan 2005 12:07:06 -0500
"Mukker, Atul" <Atulm@lsil.com> wrote:
> Please attach the dmesg output from the megaraid_mm and megaraid_mbox
> drivers as well. Also, all files from /proc/megaraid2 directory from
> 2.4 kernel driver
Attachment follows
Under 2.6.10, the 2 megaraid drivers hang in a kernel panic. I'll get a
dump tomorrow.
Stefan
--
#=- Stefan Berder tel : 6 14 80 -=#
#=- Ingénieur système et réseau 01 53 95 14 80 -=#
#=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
#=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 10722 bytes --]
brucelee:~/src# lspci -vx
0000:00:00.0 Host bridge: ServerWorks CNB20HE Host Bridge (rev 21)
Flags: fast devsel
00: 66 11 08 00 00 00 00 00 21 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:00.1 Host bridge: ServerWorks CNB20HE Host Bridge (rev 01)
Flags: bus master, medium devsel, latency 32
00: 66 11 08 00 47 01 00 22 01 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
0000:00:00.2 Host bridge: ServerWorks CNB20HE Host Bridge
Flags: medium devsel
00: 66 11 06 00 42 01 00 22 00 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:00.3 Host bridge: ServerWorks CNB20HE Host Bridge
Flags: medium devsel
00: 66 11 06 00 42 01 00 22 00 00 00 06 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:04.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC (rev 7a) (prog-if 00 [VGA])
Subsystem: Dell: Unknown device 00a2
Flags: bus master, VGA palette snoop, stepping, medium devsel, latency 32
Memory at fc000000 (32-bit, prefetchable) [size=16M]
I/O ports at ec00 [size=256]
Memory at fbeff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 1
00: 02 10 59 47 a7 00 90 02 7a 00 00 03 08 20 00 00
10: 08 00 00 fc 01 ec 00 00 00 f0 ef fb 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 00 00 5c 00 00 00 00 00 00 00 ff 00 08 00
0000:00:05.0 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Dell: Unknown device 00a2
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
BIST result: 00
I/O ports at e800 [disabled] [size=256]
Memory at fbefe000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00: 05 90 cf 00 16 01 b0 02 01 00 00 01 08 20 80 80
10: 01 e8 00 00 04 e0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 f0 fb dc 00 00 00 00 00 00 00 0b 01 28 19
0000:00:05.1 SCSI storage controller: Adaptec AIC-7899P U160/m (rev 01)
Subsystem: Dell: Unknown device 00a2
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
BIST result: 00
I/O ports at e400 [disabled] [size=256]
Memory at fbefd000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
00: 05 90 cf 00 16 01 b0 02 01 00 00 01 08 20 80 80
10: 01 e4 00 00 04 d0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 a2 00
30: 00 00 f0 fb dc 00 00 00 00 00 00 00 0a 02 28 19
0000:00:07.0 System peripheral: American Megatrends Inc. MegaRAC (rev 04)
Subsystem: American Megatrends Inc. Dell Remote Assistant Card 2
Flags: bus master, medium devsel, latency 32, IRQ 21
BIST result: 00
I/O ports at e080 [size=128]
Memory at fbefc000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fbf00000 [disabled] [size=16K]
00: 1e 10 63 90 17 01 00 02 04 00 80 08 08 20 00 80
10: 81 e0 00 00 00 c0 ef fb 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 67 07
30: 00 00 f0 fb 00 00 00 00 00 00 00 00 05 01 00 00
0000:00:08.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Dell PowerEdge 2550
Flags: bus master, medium devsel, latency 32, IRQ 26
Memory at fbefb000 (32-bit, non-prefetchable) [size=4K]
I/O ports at e040 [size=64]
Memory at fbd00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 20 00 00
10: 00 b0 ef fb 41 e0 00 00 00 00 d0 fb 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 9b 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 08 38
0000:00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 50)
Subsystem: ServerWorks OSB4 South Bridge
Flags: bus master, medium devsel, latency 0
00: 66 11 00 02 07 00 00 02 50 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 00 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 64
I/O ports at 08b0 [size=16]
00: 66 11 11 02 05 00 00 02 00 8a 01 01 00 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: b1 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: ServerWorks OSB4/CSB5 OHCI USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 31
Memory at fbefa000 (32-bit, non-prefetchable) [size=4K]
00: 66 11 20 02 17 01 80 02 04 10 03 0c 08 20 80 00
10: 00 a0 ef fb 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 20 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 50
0000:03:09.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 32
Bus: primary=03, secondary=04, subordinate=05, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: faa00000-facfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
Capabilities: [dc] Power Management version 1
00: 11 10 26 00 07 01 b0 02 05 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 03 04 05 20 c1 c1 80 22
20: a0 fa c0 fa 01 f0 f1 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:03:0a.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 32
Bus: primary=03, secondary=06, subordinate=07, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fa700000-fa9fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000eff00000
Capabilities: [dc] Power Management version 1
00: 86 80 54 b1 07 01 b0 02 00 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 03 06 07 20 b1 b1 80 22
20: 70 fa 90 fa 01 e8 f1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:03:0b.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corp. EtherExpress PRO/100+ Server Adapter (PILA8470B)
Flags: bus master, medium devsel, latency 32, IRQ 25
Memory at fa5ff000 (32-bit, non-prefetchable) [size=4K]
I/O ports at acc0 [size=64]
Memory at fa400000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
00: 86 80 29 12 17 01 90 02 08 00 00 02 08 20 00 00
10: 00 f0 5f fa c1 ac 00 00 00 00 40 fa 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 0c 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 08 38
0000:04:00.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 05) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=04, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fac00000-facfffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f7f00000
Capabilities: [dc] Power Management version 1
00: 11 10 26 00 07 01 90 02 05 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 04 05 05 20 f1 01 80 22
20: c0 fa c0 fa 01 f0 f1 f7 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:04:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3 SCSI Processor (rev 06)
Subsystem: American Megatrends Inc. QLA12160 on AMI MegaRAID
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 27
I/O ports at cc00 [size=256]
Memory at faaff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fab00000 [disabled] [size=128K]
Capabilities: [44] Power Management version 1
00: 77 10 16 12 17 01 b0 02 06 00 00 01 08 20 00 00
10: 01 cc 00 00 00 f0 af fa 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 93 84
30: 00 00 b0 fa 44 00 00 00 00 00 00 00 0b 01 40 00
0000:05:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20)
Subsystem: Dell PowerEdge RAID Controller 3/DC
Flags: bus master, medium devsel, latency 32, IRQ 23
Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fac00000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
00: 1e 10 60 19 16 01 90 02 20 00 04 01 08 20 00 00
10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 93 04
30: 00 00 c0 fa 80 00 00 00 00 00 00 00 0a 01 00 00
0000:06:00.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=06, secondary=07, subordinate=07, sec-latency=32
Memory behind bridge: fa900000-fa9fffff
Prefetchable memory behind bridge: 00000000e8000000-00000000eff00000
Capabilities: [dc] Power Management version 1
00: 86 80 54 b1 07 01 90 02 00 00 04 06 00 20 01 00
10: 00 00 00 00 00 00 00 00 06 07 07 20 f1 01 80 22
20: 90 fa 90 fa 01 e8 f1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 06 00
0000:06:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3 SCSI Processor (rev 06)
Subsystem: American Megatrends Inc. QLA12160 on AMI MegaRAID
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 28
I/O ports at bc00 [size=256]
Memory at fa7ff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fa800000 [disabled] [size=128K]
Capabilities: [44] Power Management version 1
00: 77 10 16 12 17 01 b0 02 06 00 00 01 08 20 00 00
10: 01 bc 00 00 00 f0 7f fa 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 1e 10 93 84
30: 00 00 80 fa 44 00 00 00 00 00 00 00 05 01 40 00
0000:07:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20)
Subsystem: Dell PowerEdge RAID Controller 3/DC
Flags: bus master, medium devsel, latency 32, IRQ 24
Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fa900000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
00: 1e 10 60 19 16 01 90 02 20 00 04 01 08 20 00 00
10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 93 04
30: 00 00 90 fa 80 00 00 00 00 00 00 00 0b 01 00 00
[-- Attachment #3: dmesg-2.4.28.txt --]
[-- Type: text/plain, Size: 15184 bytes --]
brucelee:~/src# dmesg
Linux version 2.4.28-bruce2.4 (root@brucelee) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 SMP Wed Jan 5 13:39:01 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003fffe000 (usable)
BIOS-e820: 000000003fffe000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
hm, page 000fe000 reserved twice.
hm, page 000ff000 reserved twice.
hm, page 000f0000 reserved twice.
On node 0 totalpages: 262142
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32766 pages.
ACPI: RSDP (v000 DELL ) @ 0x000fdcb0
ACPI: RSDT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdcc4
ACPI: FADT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdcf0
ACPI: MADT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x000fdd64
ACPI: DSDT (v001 DELL PE6450 0x00000002 MSFT 0x0100000a) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 Pentium(tm) Pro APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 17
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: DELL Product ID: POWEREDGE A2 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
I/O APIC #3 Version 17 at 0xFEC01000.
Enabling APIC mode: Flat. Using 2 I/O APICs
Processors: 2
Kernel command line: auto BOOT_IMAGE=Linux ro root=802
Initializing CPU#0
Detected 699.336 MHz processor.
Console: colour VGA+ 80x50
Calibrating delay loop... 1395.91 BogoMIPS
Memory: 1032112k/1048568k available (2290k kernel code, 16072k reserved, 758k data, 132k init, 131064k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2923.06 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1395.91 BogoMIPS
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Cascades) stepping 01
Total of 2 processors activated (2791.83 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-2, 2-5, 2-10, 2-11, 2-13 not connected.
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 48.
number of IO-APIC #2 registers: 16.
number of IO-APIC #3 registers: 16.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 000 00 1 0 0 0 0 0 0 00
0e 003 03 0 0 0 0 0 1 1 79
0f 003 03 0 0 0 0 0 1 1 81
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 000F0011
....... : max redirection entries: 000F
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 0D000000
....... : arbitration: 0D
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 1 1 0 1 0 1 1 89
01 003 03 1 1 0 1 0 1 1 91
02 003 03 1 1 0 1 0 1 1 99
03 003 03 1 1 0 1 0 1 1 A1
04 003 03 1 1 0 1 0 1 1 A9
05 003 03 1 1 0 1 0 1 1 B1
06 003 03 1 1 0 1 0 1 1 B9
07 003 03 1 1 0 1 0 1 1 C1
08 003 03 1 1 0 1 0 1 1 C9
09 003 03 1 1 0 1 0 1 1 D1
0a 003 03 1 1 0 1 0 1 1 D9
0b 003 03 1 1 0 1 0 1 1 E1
0c 003 03 1 1 0 1 0 1 1 E9
0d 003 03 1 1 0 1 0 1 1 32
0e 003 03 1 1 0 1 0 1 1 3A
0f 003 03 1 1 0 1 0 1 1 42
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 1:0
IRQ17 -> 1:1
IRQ18 -> 1:2
IRQ19 -> 1:3
IRQ20 -> 1:4
IRQ21 -> 1:5
IRQ22 -> 1:6
IRQ23 -> 1:7
IRQ24 -> 1:8
IRQ25 -> 1:9
IRQ26 -> 1:10
IRQ27 -> 1:11
IRQ28 -> 1:12
IRQ29 -> 1:13
IRQ30 -> 1:14
IRQ31 -> 1:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 699.2856 MHz.
..... host bus clock speed is 99.8976 MHz.
cpu: 0, clocks: 998976, slice: 332992
CPU0<T0:998976,T1:665984,D:0,S:332992,C:998976>
cpu: 1, clocks: 998976, slice: 332992
CPU1<T0:998976,T1:332992,D:0,S:332992,C:998976>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfc7ee, last bus=16
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Discovered primary peer bus 03 [IRQ]
PCI: Discovered primary peer bus 10 [IRQ]
PCI: Using IRQ router ServerWorks [1166/0200] at 00:0f.0
PCI->APIC IRQ transform: (B0,I5,P0) -> 17
PCI->APIC IRQ transform: (B0,I5,P1) -> 18
PCI->APIC IRQ transform: (B0,I7,P0) -> 21
PCI->APIC IRQ transform: (B0,I8,P0) -> 26
PCI->APIC IRQ transform: (B0,I15,P0) -> 31
PCI->APIC IRQ transform: (B3,I11,P0) -> 25
PCI->APIC IRQ transform: (B4,I1,P0) -> 27
PCI->APIC IRQ transform: (B5,I0,P0) -> 23
PCI->APIC IRQ transform: (B6,I1,P0) -> 28
PCI->APIC IRQ transform: (B7,I0,P0) -> 24
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
HP CISS Driver (v 2.4.52)
Intel(R) PRO/100 Network Driver - version 2.3.43-k1
Copyright (c) 2004 Intel Corporation
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
cpu cycle saver enabled
e100: selftest OK.
e100: eth1: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
cpu cycle saver enabled
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: no supported devices found.
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] Initialized radeon 1.7.0 20020828 on minor 1
[drm:drm_init] *ERROR* Cannot initialize the agpgart module.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:pio, hdd:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-cdrom driver.
hda: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
megaraid: v2.10.3 (Release Date: Thu Apr 8 16:16:05 EDT 2004)
megaraid: found 0x101e:0x1960:bus 5:slot 0:func 0
scsi2:Found MegaRAID controller at 0xf8808000, IRQ:23
megaraid: [1.57:3.13] detected 2 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: found 0x101e:0x1960:bus 7:slot 0:func 0
scsi3:Found MegaRAID controller at 0xf880a000, IRQ:24
megaraid: [161J:3.17] detected 0 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: Cluster driver, initiator id:14
scsi2 : LSI Logic MegaRAID 1.57 254 commands 16 targs 5 chans 7 luns
scsi3 : LSI Logic MegaRAID 161J 254 commands 16 targs 5 chans 7 luns
scsi2: scanning scsi channel 0 for logical drives.
Vendor: MegaRAID Model: LD0 RAID1 34678R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
Vendor: MegaRAID Model: LD1 RAID5 46780R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
scsi2: scanning scsi channel 1 for logical drives.
scsi2: scanning scsi channel 2 for logical drives.
scsi2: scanning scsi channel 4 [P0] for physical devices.
Vendor: DELL Model: 1x4 U2W SCSI BP Rev: 1.27
Type: Processor ANSI SCSI revision: 02
scsi2: scanning scsi channel 5 [P1] for physical devices.
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
scsi3: scanning scsi channel 0 for logical drives.
scsi3: scanning scsi channel 1 for logical drives.
scsi3: scanning scsi channel 2 for logical drives.
scsi3: scanning scsi channel 4 [P0] for physical devices.
scsi3: scanning scsi channel 5 [P1] for physical devices.
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi2, channel 0, id 1, lun 0
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
Partition check:
sda: sda1 sda2
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: sdb1
es1371: version v0.32 time 13:43:04 Jan 5 2005
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xf880c000, IRQ 31
host/usb-ohci.c: usb-00:0f.2, ServerWorks OSB4/CSB5 OHCI USB Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 152 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ds: no socket drivers loaded!
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 132k freed
Adding Swap: 1000424k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04Aborted Command
e100: eth0 NIC Link is Up 100 Mbps Full duplex
[-- Attachment #4: proc-megaraid-2.4.28.tar.bz2 --]
[-- Type: application/octet-stream, Size: 426 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-05 19:03 Mukker, Atul
2005-01-06 10:49 ` Stefan Berder
0 siblings, 1 reply; 10+ messages in thread
From: Mukker, Atul @ 2005-01-05 19:03 UTC (permalink / raw)
To: 'Stefan Berder', Mukker, Atul
Cc: 'linux-scsi@vger.kernel.org'
The proc files are empty! Try copying to a different location before
creating tarball.
-Atul Mukker
> -----Original Message-----
> From: Stefan Berder [mailto:sbe@oleane.net]
> Sent: Wednesday, January 05, 2005 1:09 PM
> To: Mukker, Atul
> Cc: 'linux-scsi@vger.kernel.org'
> Subject: Re: Problem with megaraid and PERC3/dc on a poweredge 6450
>
> On Wed, 5 Jan 2005 12:07:06 -0500
> "Mukker, Atul" <Atulm@lsil.com> wrote:
>
> > Please attach the dmesg output from the megaraid_mm and
> megaraid_mbox
> > drivers as well. Also, all files from /proc/megaraid2 directory from
> > 2.4 kernel driver
>
> Attachment follows
> Under 2.6.10, the 2 megaraid drivers hang in a kernel panic.
> I'll get a dump tomorrow.
>
> Stefan
> --
> #=- Stefan Berder tel : 6 14 80 -=#
> #=- Ingénieur système et réseau 01 53 95 14 80 -=#
> #=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
> #=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Problem with megaraid and PERC3/dc on a poweredge 6450
2005-01-05 19:03 Mukker, Atul
@ 2005-01-06 10:49 ` Stefan Berder
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Berder @ 2005-01-06 10:49 UTC (permalink / raw)
To: Mukker, Atul; +Cc: 'linux-scsi@vger.kernel.org'
[-- Attachment #1: Type: text/plain, Size: 454 bytes --]
On Wed, 5 Jan 2005 14:03:57 -0500
"Mukker, Atul" <Atulm@lsil.com> wrote:
> The proc files are empty! Try copying to a different location before
> creating tarball.
should be ok now ::)
Stef
--
#=- Stefan Berder tel : 6 14 80 -=#
#=- Ingénieur système et réseau 01 53 95 14 80 -=#
#=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
#=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
[-- Attachment #2: proc-megaraid-2.4.28.tar.bz2 --]
[-- Type: application/octet-stream, Size: 1843 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-06 14:13 Mukker, Atul
2005-01-06 17:13 ` Stefan Berder
0 siblings, 1 reply; 10+ messages in thread
From: Mukker, Atul @ 2005-01-06 14:13 UTC (permalink / raw)
To: 'Stefan Berder'; +Cc: 'linux-scsi@vger.kernel.org'
Thanks for the files. Both of these controllers should work with the new
drivers, megaraid_mbox and megaraid_mm. Now, I am waiting on the kernel
messages, before suggesting a prognosis. I am sure you know how to collect
the messages by re-directing them to a serial console?
Thanks
-------------
Atul Mukker
Architect, Drivers and BIOS
LSI Logic Corporation
> -----Original Message-----
> From: Stefan Berder [mailto:sbe@oleane.net]
> Sent: Thursday, January 06, 2005 5:49 AM
> To: Mukker, Atul
> Cc: 'linux-scsi@vger.kernel.org'
> Subject: Re: Problem with megaraid and PERC3/dc on a poweredge 6450
>
> On Wed, 5 Jan 2005 14:03:57 -0500
> "Mukker, Atul" <Atulm@lsil.com> wrote:
>
> > The proc files are empty! Try copying to a different
> location before
> > creating tarball.
> should be ok now ::)
>
> Stef
> --
> #=- Stefan Berder tel : 6 14 80 -=#
> #=- Ingénieur système et réseau 01 53 95 14 80 -=#
> #=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
> #=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Problem with megaraid and PERC3/dc on a poweredge 6450
2005-01-06 14:13 Problem with megaraid and PERC3/dc on a poweredge 6450 Mukker, Atul
@ 2005-01-06 17:13 ` Stefan Berder
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Berder @ 2005-01-06 17:13 UTC (permalink / raw)
To: Mukker, Atul; +Cc: 'linux-scsi@vger.kernel.org'
[-- Attachment #1: Type: text/plain, Size: 802 bytes --]
On Thu, 6 Jan 2005 09:13:32 -0500
"Mukker, Atul" <Atulm@lsil.com> wrote:
> Thanks for the files. Both of these controllers should work with the
> new drivers, megaraid_mbox and megaraid_mm. Now, I am waiting on the
> kernel messages, before suggesting a prognosis. I am sure you know how
> to collect the messages by re-directing them to a serial console?
Done, a weird thing is that the megaraid_mm driver no more panics ...
but it does some timeout things I don't have in 2.4.28 with megaraid2.
Sorry for the noise ...
Stefan
--
#=- Stefan Berder tel : 6 14 80 -=#
#=- Ingénieur système et réseau 01 53 95 14 80 -=#
#=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
#=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
[-- Attachment #2: 2.6.10-megaraid_mm-boot.txt --]
[-- Type: text/plain, Size: 24590 bytes --]
Linux version 2.6.10-bruce2.6 (root@brucelee) (gcc version 3.3.4 (Debian 1:3.3.5
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003fffe000 (usable)
BIOS-e820: 000000003fffe000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:10 APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 17
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 3, version 17, address 0xfec01000, GSI 16-31
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux ro root=802 console=tty0 console=ttyS0,960
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 699.583 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x50
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034324k/1048568k available (2595k kernel code, 13668k reserved, 1204k )
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
tbxface-0118 [02] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:....................................................
Table [DSDT](id F004) - 767 Objects with 95 Devices 245 Methods 66 Regions
ACPI Namespace successfully loaded at root c051c680
evxfevnt-0094 [03] acpi_enable : Transition to ACPI mode successful
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2927.35 usecs.
task migration cache decay timeout: 3 msecs.
Booting processor 1/0 eip 2000
Initializing CPU#1
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Cascades) stepping 01
Total of 2 processors activated (2777.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc7ee, last bus=16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
evgpeblk-0979 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0987 [06] ev_create_gpe_block : Found 1 Wake, Enabled 0 Runtime GPEsk
evgpeblk-0979 [06] ev_create_gpe_block : GPE 20 to 3F [_GPE] 4 regs on int 0x9
evgpeblk-0987 [06] ev_create_gpe_block : Found 1 Wake, Enabled 1 Runtime GPEsk
Completing Region/Field/Buffer/Package initialization:..........................
Initialized 66/66 Regions 0/0 Fields 17/17 Buffers 13/15 Packages (776 nodes)
Executing all Device _STA and_INI methods:...................................[A3
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
..[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
..................
101 Devices found containing: 101 _STA, 0 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
[ACPI Debug] Integer: 0x00000003
ACPI: PCI Root Bridge [PCI1] (00:03)
PCI: Probing PCI hardware (bus 03)
[ACPI Debug] Integer: 0x00000010
ACPI: PCI Root Bridge [PCI2] (00:10)
PCI: Probing PCI hardware (bus 10)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 6 7 9 *10 11 12 14)
ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK9] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 5 6 7 *10 11 12 14)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
[ACPI Debug] String: [0x09] "MEM _CRS."
[ACPI Debug] Buffer: [0x4A]highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
testing md5
test 1:
d41d8cd98f00b204e9800998ecf8427e
pass
test 2:
0cc175b9c0f1b6a831c399e269772661
pass
test 3:
900150983cd24fb0d6963f7d28e17f72
pass
test 4:
f96b697d7cb7938d525a2f31aaf161d0
pass
test 5:
c3fcd3d76192e4007dfb496cca67e13b
pass
test 6:
d174ab98d277d9f5a5611c2c9f419d9f
pass
test 7:
57edf4a22be3c955ac49da2e2107b67a
pass
testing md5 across pages
test 1:
c3fcd3d76192e4007dfb496cca67e13b
pass
testing sha1
failed to load transform for sha1
testing des ECB encryption
test 1 (64 bit key):
c95744256a5ed31d
pass
test 2 (64 bit key):
f79c892a338f4a8b
pass
test 3 (64 bit key):
690f5b0d9a26939b
pass
test 4 (64 bit key):
c95744256a5ed31df79c892a338f4a8bb49926f71fe1d490
pass
test 5 (64 bit key):
setkey() failed flags=100100
c95744256a5ed31d
pass
testing des ECB encryption across pages (chunking)
test 1 (64 bit key):
page 0
c95744256a5ed31d
pass
page 1
f79c892a338f4a8b
pass
test 2 (64 bit key):
page 0
c95744256a5ed31df79c892a338f
pass
page 1
4a8bb49926f71fe1d490
pass
page 2
f79c892a338f4a8b
pass
test 3 (64 bit key):
page 0
c957
pass
page 1
44
pass
page 2
256a5e
pass
page 3
d31df79c892a338f4a8bb49926f71fe1d490
pass
test 4 (64 bit key):
page 0
c957
pass
page 1
4425
pass
page 2
6a5e
pass
page 3
d31d
pass
page 4
f79c892a338f4a8b
pass
test 5 (64 bit key):
page 0
c9
pass
page 1
57
pass
page 2
44
pass
page 3
25
pass
page 4
6a
pass
page 5
5e
pass
page 6
d3
pass
page 7
1d
pass
testing des ECB decryption
test 1 (64 bit key):
0123456789abcde7
pass
test 2 (64 bit key):
01a1d6d039776742
pass
testing des ECB decryption across pages (chunking)
test 1 (64 bit key):
page 0
0123456789abcde7
pass
page 1
a3997bcaaf69a0f5
pass
test 2 (64 bit key):
page 0
012345
pass
page 1
6789abcde7a3997bcaaf69a0
pass
page 2
f5
pass
testing des CBC encryption
test 1 (64 bit key):
ccd173ffab2039f4acd8aefddfd8a1eb468e91157888ba68
pass
test 2 (64 bit key):
e5c7cdde872bf27c
pass
test 3 (64 bit key):
43e934008c389c0f
pass
test 4 (64 bit key):
683788499a7c05f6
pass
testing des CBC encryption across pages (chunking)
test 1 (64 bit key):
page 0
ccd173ffab2039f4acd8aefddf
pass
page 1
d8a1eb468e91157888ba68
pass
testing des CBC decryption
test 1 (64 bit key):
4e6f772069732074
pass
test 2 (64 bit key):
68652074696d6520
pass
test 3 (64 bit key):
666f7220616c6c20
pass
testing des CBC decryption across pages (chunking)
test 1 (64 bit key):
page 0
666f7220
pass
page 1
616c6c20
pass
testing des3_ede ECB encryption
test 1 (192 bit key):
18d748e563620572
pass
test 2 (192 bit key):
c07d2a0fa566fa30
pass
test 3 (192 bit key):
e1ef62c332fe825b
pass
testing des3_ede ECB encryption across pages (chunking)
testing des3_ede ECB decryption
test 1 (192 bit key):
736f6d6564617461
pass
test 2 (192 bit key):
7371756967676c65
pass
test 3 (192 bit key):
0000000000000000
pass
testing des3_ede ECB decryption across pages (chunking)
testing md4
failed to load transform for md4
testing sha256
failed to load transform for sha256
testing blowfish ECB encryption
test 1 (64 bit key):
4ef997456198dd78
pass
test 2 (64 bit key):
a790795108ea3cae
pass
test 3 (64 bit key):
e87a244e2cc85e82
pass
test 4 (128 bit key):
93142887ee3be15c
pass
test 5 (168 bit key):
e6f51ed79b9db21f
pass
test 6 (448 bit key):
c04504012e4e1f53
pass
testing blowfish ECB encryption across pages (chunking)
testing blowfish ECB decryption
test 1 (64 bit key):
0000000000000000
pass
test 2 (64 bit key):
0123456789abcdef
pass
test 3 (64 bit key):
fedcba9876543210
pass
test 4 (128 bit key):
fedcba9876543210
pass
test 5 (168 bit key):
fedcba9876543210
pass
test 6 (448 bit key):
fedcba9876543210
pass
testing blowfish ECB decryption across pages (chunking)
testing blowfish CBC encryption
test 1 (128 bit key):
6b77b4d63006dee605b156e27403979358deb9e7154616d959f1652bd5ff92cc
pass
testing blowfish CBC encryption across pages (chunking)
testing blowfish CBC decryption
test 1 (128 bit key):
37363534333231204e6f77206973207468652074696d6520666f722000000000
pass
testing blowfish CBC decryption across pages (chunking)
testing twofish ECB encryption
failed to load transform for twofish ECB
testing twofish ECB decryption
failed to load transform for twofish ECB
testing twofish CBC encryption
failed to load transform for twofish CBC
testing twofish CBC decryption
failed to load transform for twofish CBC
testing serpent ECB encryption
failed to load transform for serpent ECB
testing serpent ECB decryption
failed to load transform for serpent ECB
testing tnepres ECB encryption
failed to load transform for tnepres ECB
testing tnepres ECB decryption
failed to load transform for tnepres ECB
testing aes ECB encryption
test 1 (128 bit key):
69c4e0d86a7b0430d8cdb78070b4c55a
pass
test 2 (192 bit key):
dda97ca4864cdfe06eaf70a0ec0d7191
pass
test 3 (256 bit key):
8ea2b7ca516745bfeafc49904b496089
pass
testing aes ECB encryption across pages (chunking)
testing aes ECB decryption
test 1 (128 bit key):
00112233445566778899aabbccddeeff
pass
test 2 (192 bit key):
00112233445566778899aabbccddeeff
pass
test 3 (256 bit key):
00112233445566778899aabbccddeeff
pass
testing aes ECB decryption across pages (chunking)
testing cast5 ECB encryption
failed to load transform for cast5 ECB
testing cast5 ECB decryption
failed to load transform for cast5 ECB
testing cast6 ECB encryption
failed to load transform for cast6 ECB
testing cast6 ECB decryption
failed to load transform for cast6 ECB
testing arc4 ECB encryption
failed to load transform for arc4 ECB
testing arc4 ECB decryption
failed to load transform for arc4 ECB
testing tea ECB encryption
failed to load transform for tea ECB
testing tea ECB decryption
failed to load transform for tea ECB
testing xtea ECB encryption
failed to load transform for xtea ECB
testing xtea ECB decryption
failed to load transform for xtea ECB
testing khazad ECB encryption
failed to load transform for khazad ECB
testing khazad ECB decryption
failed to load transform for khazad ECB
testing anubis ECB encryption
failed to load transform for anubis ECB
testing anubis ECB decryption
failed to load transform for anubis ECB
testing anubis CBC encryption
failed to load transform for anubis CBC
testing anubis CBC decryption
failed to load transform for anubis CBC
testing sha384
failed to load transform for sha384
testing sha512
failed to load transform for sha512
testing wp512
failed to load transform for wp512
testing wp384
failed to load transform for wp384
testing wp256
failed to load transform for wp256
testing deflate compression
failed to load transform for deflate
testing crc32c
testing crc32c initialized to 00000000: pass
testing crc32c setkey returns 12345678 : pass
testing crc32c using update/final:
0e2c157f:OK e980ebf6:OK de74bded:OK d579c862:OK ba979ad0:OK 2b29d913:OK
testing crc32c using incremental accumulator:
24c5d375:OK
testing crc32c using digest:
24c5d375:OK
pass
crc32c test complete
testing michael_mic
failed to load transform for michael_mic
vesafb: probe of vesafb0 failed with error -6
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
elevator: using anticipatory as default io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 26 (level, low) -> IRQ 26
e100: eth0: e100_probe: addr 0xfbefb000, irq 26, MAC addr 00:B0:D0:EA:24:FE
ACPI: PCI interrupt 0000:03:0b.0[A] -> GSI 25 (level, low) -> IRQ 25
e100: eth1: e100_probe: addr 0xfa5ff000, irq 25, MAC addr 00:02:B3:65:5E:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:pio, hdd:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:00:05.1[B] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
qla1280: Skipping AMI SubSys Vendor ID Chip
qla1280: Skipping AMI SubSys Vendor ID Chip
megaraid cmm: 2.20.2.3 (Release Date: Thu Dec 9 19:02:14 EST 2004)
megaraid: 2.20.4.1 (Release Date: Thu Nov 4 17:44:59 EST 2004)
megaraid: probe new device 0x101e:0x1960:0x1028:0x0493: bus 5:slot 0:func 0
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 23 (level, low) -> IRQ 23
megaraid: fw version:[1.57] bios version:[3.13]
scsi2 : LSI Logic MegaRAID driver
scsi[2]: scanning scsi channel 0 [Phy 0] for non-raid devices
Vendor: DELL Model: 1x4 U2W SCSI BP Rev: 1.27
Type: Processor ANSI SCSI revision: 02
scsi[2]: scanning scsi channel 1 [Phy 1] for non-raid devices
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
megaraid: aborting-90 cmd=a0 <c=1 t=15 l=0>
megaraid abort: 90:0[1:15], fw owner
megaraid: reseting the host...
megaraid: 1 outstanding commands. Max wait 180 sec
megaraid mbox: Wait for 1 commands to complete:180
megaraid mbox: Wait for 1 commands to complete:175
megaraid mbox: Wait for 1 commands to complete:170
megaraid mbox: Wait for 1 commands to complete:165
megaraid mbox: Wait for 1 commands to complete:160
megaraid mbox: Wait for 1 commands to complete:155
megaraid mbox: Wait for 1 commands to complete:150
megaraid mbox: Wait for 1 commands to complete:145
megaraid mbox: Wait for 1 commands to complete:140
megaraid mbox: Wait for 1 commands to complete:135
megaraid mbox: Wait for 1 commands to complete:130
megaraid mbox: Wait for 1 commands to complete:125
megaraid mbox: Wait for 1 commands to complete:120
megaraid mbox: reset sequence completed sucessfully
megaraid: aborting-91 cmd=a0 <c=1 t=15 l=0>
megaraid abort: 91:0[1:15], fw owner
megaraid: reseting the host...
megaraid: 1 outstanding commands. Max wait 180 sec
megaraid mbox: Wait for 1 commands to complete:180
megaraid mbox: Wait for 1 commands to complete:175
megaraid mbox: Wait for 1 commands to complete:170
megaraid mbox: Wait for 1 commands to complete:165
megaraid mbox: Wait for 1 commands to complete:160
megaraid mbox: Wait for 1 commands to complete:155
megaraid mbox: Wait for 1 commands to complete:150
megaraid mbox: reset sequence completed sucessfully
megaraid: aborting-92 cmd=a0 <c=1 t=15 l=0>
megaraid abort: 92:0[1:15], fw owner
megaraid: reseting the host...
megaraid: 1 outstanding commands. Max wait 180 sec
megaraid mbox: Wait for 1 commands to complete:180
megaraid mbox: reset sequence completed sucessfully
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
scsi[2]: scanning scsi channel 2 [virtual] for logical drives
Vendor: MegaRAID Model: LD0 RAID1 34678R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
Vendor: MegaRAID Model: LD1 RAID5 46780R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
megaraid: probe new device 0x101e:0x1960:0x1028:0x0493: bus 7:slot 0:func 0
ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 24 (level, low) -> IRQ 24
megaraid: fw version:[161J] bios version:[3.17]
megaraid: cluster firmware, initiator ID: 14
scsi3 : LSI Logic MegaRAID driver
scsi[3]: scanning scsi channel 0 [Phy 0] for non-raid devices
scsi[3]: scanning scsi channel 1 [Phy 1] for non-raid devices
scsi[3]: scanning scsi channel 2 [virtual] for logical drives
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
sda: sda1 sda2
Attached scsi disk sda at scsi2, channel 2, id 0, lun 0
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
sdb: sdb1
Attached scsi disk sdb at scsi2, channel 2, id 1, lun 0
ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:0f.2[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:0f.2: ServerWorks OSB4/CSB5 OHCI USB Controller
ohci_hcd 0000:00:0f.2: irq 10, pci mem 0xfbefa000
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 180 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 240k freed
INIT: version 2.86 booting
mount: wrong fs type, bad option, bad superblock on tmpfs,
or too many mounted file systems
Setting disc parameters: done.
Activating swap.Adding 1000424k swap on /dev/sda1. Priority:-1 extents:1
Checking root file system...
fsck 1.35 (28-Feb-2004)
/dev/sda2: cleanEXT3 FS on sda2, , 57469/4316928 internal journal
files, 379442/8627456 blocks
mount: wrong fs type, bad option, bad superblock on tmpfs,
or too many mounted file systems
System time was Thu Jan 6 18:08:35 UTC 2005.
Setting the System Clock using the Hardware Clock as reference...
System Clock set. System local time is now Thu Jan 6 18:08:37 UTC 2005.
Calculating module dependencies... done.
Loading modules...
e100
FATAL: Module e100 not found.
All modules loaded.
Creating device-mapper devices...done.
Checking all file systems...
fsck 1.35 (28-Feb-2004)
Setting kernel variables ...
... done.
Mounting local filesystems...
Cleaning /tmp /var/run /var/lock.
mount: wrong fs type, bad option, bad superblock on tmpfs,
or too many mounted file systems
Running 0dns-down to make sure resolv.conf is ok...done.
Cleaning: /etc/network/ifstate.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces...e100: eth0: e100_watchdog: link up, 100Mbps, fx
done.
Loading the saved-state of the serial devices...
/dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A
/dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A
Setting the System Clock using the Hardware Clock as reference...
...
[-- Attachment #3: 2.6.10-megaraid-boot.txt --]
[-- Type: text/plain, Size: 21718 bytes --]
Linux version 2.6.10-bruce2.6 (root@brucelee) (gcc version 3.3.4 (Debian 1:3.3.5
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003fffe000 (usable)
BIOS-e820: 000000003fffe000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:10 APIC version 17
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 17
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-15
ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16])
IOAPIC[1]: apic_id 3, version 17, address 0xfec01000, GSI 16-31
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux ro root=802 console=ttyS0,9600
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 699.574 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x50
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034324k/1048568k available (2597k kernel code, 13668k reserved, 1202k )
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
tbxface-0118 [02] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:....................................................
Table [DSDT](id F004) - 767 Objects with 95 Devices 245 Methods 66 Regions
ACPI Namespace successfully loaded at root c051c680
evxfevnt-0094 [03] acpi_enable : Transition to ACPI mode successful
CPU0: Intel Pentium III (Cascades) stepping 01
per-CPU timeslice cutoff: 2927.35 usecs.
task migration cache decay timeout: 3 msecs.
Booting processor 1/0 eip 2000
Initializing CPU#1
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 1024K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Cascades) stepping 01
Total of 2 processors activated (2777.08 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc7ee, last bus=16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
evgpeblk-0979 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0987 [06] ev_create_gpe_block : Found 1 Wake, Enabled 0 Runtime GPEsk
evgpeblk-0979 [06] ev_create_gpe_block : GPE 20 to 3F [_GPE] 4 regs on int 0x9
evgpeblk-0987 [06] ev_create_gpe_block : Found 1 Wake, Enabled 1 Runtime GPEsk
Completing Region/Field/Buffer/Package initialization:..........................
Initialized 66/66 Regions 0/0 Fields 17/17 Buffers 13/15 Packages (776 nodes)
Executing all Device _STA and_INI methods:...................................[A3
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
.[ACPI Debug] Integer: 0x00000003
..[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
.[ACPI Debug] Integer: 0x00000010
..................
101 Devices found containing: 101 _STA, 0 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
[ACPI Debug] Integer: 0x00000003
ACPI: PCI Root Bridge [PCI1] (00:03)
PCI: Probing PCI hardware (bus 03)
[ACPI Debug] Integer: 0x00000010
ACPI: PCI Root Bridge [PCI2] (00:10)
PCI: Probing PCI hardware (bus 10)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 *10 11 12 14)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNK6] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 3 4 5 6 7 9 *10 11 12 14)
ACPI: PCI Interrupt Link [LNK8] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNK9] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14) *0, disabled.
ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 5 6 7 *10 11 12 14)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
[ACPI Debug] String: [0x09] "MEM _CRS."
[ACPI Debug] Buffer: [0x4A]highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
testing md5
test 1:
d41d8cd98f00b204e9800998ecf8427e
pass
test 2:
0cc175b9c0f1b6a831c399e269772661
pass
test 3:
900150983cd24fb0d6963f7d28e17f72
pass
test 4:
f96b697d7cb7938d525a2f31aaf161d0
pass
test 5:
c3fcd3d76192e4007dfb496cca67e13b
pass
test 6:
d174ab98d277d9f5a5611c2c9f419d9f
pass
test 7:
57edf4a22be3c955ac49da2e2107b67a
pass
testing md5 across pages
test 1:
c3fcd3d76192e4007dfb496cca67e13b
pass
testing sha1
failed to load transform for sha1
testing des ECB encryption
test 1 (64 bit key):
c95744256a5ed31d
pass
test 2 (64 bit key):
f79c892a338f4a8b
pass
test 3 (64 bit key):
690f5b0d9a26939b
pass
test 4 (64 bit key):
c95744256a5ed31df79c892a338f4a8bb49926f71fe1d490
pass
test 5 (64 bit key):
setkey() failed flags=100100
c95744256a5ed31d
pass
testing des ECB encryption across pages (chunking)
test 1 (64 bit key):
page 0
c95744256a5ed31d
pass
page 1
f79c892a338f4a8b
pass
test 2 (64 bit key):
page 0
c95744256a5ed31df79c892a338f
pass
page 1
4a8bb49926f71fe1d490
pass
page 2
f79c892a338f4a8b
pass
test 3 (64 bit key):
page 0
c957
pass
page 1
44
pass
page 2
256a5e
pass
page 3
d31df79c892a338f4a8bb49926f71fe1d490
pass
test 4 (64 bit key):
page 0
c957
pass
page 1
4425
pass
page 2
6a5e
pass
page 3
d31d
pass
page 4
f79c892a338f4a8b
pass
test 5 (64 bit key):
page 0
c9
pass
page 1
57
pass
page 2
44
pass
page 3
25
pass
page 4
6a
pass
page 5
5e
pass
page 6
d3
pass
page 7
1d
pass
testing des ECB decryption
test 1 (64 bit key):
0123456789abcde7
pass
test 2 (64 bit key):
01a1d6d039776742
pass
testing des ECB decryption across pages (chunking)
test 1 (64 bit key):
page 0
0123456789abcde7
pass
page 1
a3997bcaaf69a0f5
pass
test 2 (64 bit key):
page 0
012345
pass
page 1
6789abcde7a3997bcaaf69a0
pass
page 2
f5
pass
testing des CBC encryption
test 1 (64 bit key):
ccd173ffab2039f4acd8aefddfd8a1eb468e91157888ba68
pass
test 2 (64 bit key):
e5c7cdde872bf27c
pass
test 3 (64 bit key):
43e934008c389c0f
pass
test 4 (64 bit key):
683788499a7c05f6
pass
testing des CBC encryption across pages (chunking)
test 1 (64 bit key):
page 0
ccd173ffab2039f4acd8aefddf
pass
page 1
d8a1eb468e91157888ba68
pass
testing des CBC decryption
test 1 (64 bit key):
4e6f772069732074
pass
test 2 (64 bit key):
68652074696d6520
pass
test 3 (64 bit key):
666f7220616c6c20
pass
testing des CBC decryption across pages (chunking)
test 1 (64 bit key):
page 0
666f7220
pass
page 1
616c6c20
pass
testing des3_ede ECB encryption
test 1 (192 bit key):
18d748e563620572
pass
test 2 (192 bit key):
c07d2a0fa566fa30
pass
test 3 (192 bit key):
e1ef62c332fe825b
pass
testing des3_ede ECB encryption across pages (chunking)
testing des3_ede ECB decryption
test 1 (192 bit key):
736f6d6564617461
pass
test 2 (192 bit key):
7371756967676c65
pass
test 3 (192 bit key):
0000000000000000
pass
testing des3_ede ECB decryption across pages (chunking)
testing md4
failed to load transform for md4
testing sha256
failed to load transform for sha256
testing blowfish ECB encryption
test 1 (64 bit key):
4ef997456198dd78
pass
test 2 (64 bit key):
a790795108ea3cae
pass
test 3 (64 bit key):
e87a244e2cc85e82
pass
test 4 (128 bit key):
93142887ee3be15c
pass
test 5 (168 bit key):
e6f51ed79b9db21f
pass
test 6 (448 bit key):
c04504012e4e1f53
pass
testing blowfish ECB encryption across pages (chunking)
testing blowfish ECB decryption
test 1 (64 bit key):
0000000000000000
pass
test 2 (64 bit key):
0123456789abcdef
pass
test 3 (64 bit key):
fedcba9876543210
pass
test 4 (128 bit key):
fedcba9876543210
pass
test 5 (168 bit key):
fedcba9876543210
pass
test 6 (448 bit key):
fedcba9876543210
pass
testing blowfish ECB decryption across pages (chunking)
testing blowfish CBC encryption
test 1 (128 bit key):
6b77b4d63006dee605b156e27403979358deb9e7154616d959f1652bd5ff92cc
pass
testing blowfish CBC encryption across pages (chunking)
testing blowfish CBC decryption
test 1 (128 bit key):
37363534333231204e6f77206973207468652074696d6520666f722000000000
pass
testing blowfish CBC decryption across pages (chunking)
testing twofish ECB encryption
failed to load transform for twofish ECB
testing twofish ECB decryption
failed to load transform for twofish ECB
testing twofish CBC encryption
failed to load transform for twofish CBC
testing twofish CBC decryption
failed to load transform for twofish CBC
testing serpent ECB encryption
failed to load transform for serpent ECB
testing serpent ECB decryption
failed to load transform for serpent ECB
testing tnepres ECB encryption
failed to load transform for tnepres ECB
testing tnepres ECB decryption
failed to load transform for tnepres ECB
testing aes ECB encryption
test 1 (128 bit key):
69c4e0d86a7b0430d8cdb78070b4c55a
pass
test 2 (192 bit key):
dda97ca4864cdfe06eaf70a0ec0d7191
pass
test 3 (256 bit key):
8ea2b7ca516745bfeafc49904b496089
pass
testing aes ECB encryption across pages (chunking)
testing aes ECB decryption
test 1 (128 bit key):
00112233445566778899aabbccddeeff
pass
test 2 (192 bit key):
00112233445566778899aabbccddeeff
pass
test 3 (256 bit key):
00112233445566778899aabbccddeeff
pass
testing aes ECB decryption across pages (chunking)
testing cast5 ECB encryption
failed to load transform for cast5 ECB
testing cast5 ECB decryption
failed to load transform for cast5 ECB
testing cast6 ECB encryption
failed to load transform for cast6 ECB
testing cast6 ECB decryption
failed to load transform for cast6 ECB
testing arc4 ECB encryption
failed to load transform for arc4 ECB
testing arc4 ECB decryption
failed to load transform for arc4 ECB
testing tea ECB encryption
failed to load transform for tea ECB
testing tea ECB decryption
failed to load transform for tea ECB
testing xtea ECB encryption
failed to load transform for xtea ECB
testing xtea ECB decryption
failed to load transform for xtea ECB
testing khazad ECB encryption
failed to load transform for khazad ECB
testing khazad ECB decryption
failed to load transform for khazad ECB
testing anubis ECB encryption
failed to load transform for anubis ECB
testing anubis ECB decryption
failed to load transform for anubis ECB
testing anubis CBC encryption
failed to load transform for anubis CBC
testing anubis CBC decryption
failed to load transform for anubis CBC
testing sha384
failed to load transform for sha384
testing sha512
failed to load transform for sha512
testing wp512
failed to load transform for wp512
testing wp384
failed to load transform for wp384
testing wp256
failed to load transform for wp256
testing deflate compression
failed to load transform for deflate
testing crc32c
testing crc32c initialized to 00000000: pass
testing crc32c setkey returns 12345678 : pass
testing crc32c using update/final:
0e2c157f:OK e980ebf6:OK de74bded:OK d579c862:OK ba979ad0:OK 2b29d913:OK
testing crc32c using incremental accumulator:
24c5d375:OK
testing crc32c using digest:
24c5d375:OK
pass
crc32c test complete
testing michael_mic
failed to load transform for michael_mic
vesafb: probe of vesafb0 failed with error -6
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
elevator: using anticipatory as default io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 26 (level, low) -> IRQ 26
e100: eth0: e100_probe: addr 0xfbefb000, irq 26, MAC addr 00:B0:D0:EA:24:FE
ACPI: PCI interrupt 0000:03:0b.0[A] -> GSI 25 (level, low) -> IRQ 25
e100: eth1: e100_probe: addr 0xfa5ff000, irq 25, MAC addr 00:02:B3:65:5E:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SvrWks OSB4: IDE controller at PCI slot 0000:00:0f.1
SvrWks OSB4: chipset revision 0
SvrWks OSB4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:pio, hdd:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X CD-ROM drive, 128kB Cache, (U)DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:00:05.1[B] -> GSI 18 (level, low) -> IRQ 18
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec aic7899 Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
qla1280: Skipping AMI SubSys Vendor ID Chip
qla1280: Skipping AMI SubSys Vendor ID Chip
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 23 (level, low) -> IRQ 23
megaraid: found 0x101e:0x1960:bus 5:slot 0:func 0
scsi2:Found MegaRAID controller at 0xf8810000, IRQ:23
megaraid: [1.57:3.13] detected 2 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
scsi2 : LSI Logic MegaRAID 1.57 254 commands 16 targs 5 chans 7 luns
scsi2: scanning scsi channel 0 for logical drives.
Vendor: MegaRAID Model: LD0 RAID1 34678R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
Vendor: MegaRAID Model: LD1 RAID5 46780R Rev: 1.57
Type: Direct-Access ANSI SCSI revision: 02
scsi2: scanning scsi channel 1 for logical drives.
scsi2: scanning scsi channel 2 for logical drives.
scsi2: scanning scsi channel 4 [P0] for physical devices.
Vendor: DELL Model: 1x4 U2W SCSI BP Rev: 1.27
Type: Processor ANSI SCSI revision: 02
scsi2: scanning scsi channel 5 [P1] for physical devices.
Vendor: Dell Model: 12 BAY U2W CU Rev: 0209
Type: Processor ANSI SCSI revision: 03
megaraid: ABORTING-81 cmd=a0 <c=5 t=15 l=0>
megaraid: ABORTING-81[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-81 cmd=a0 <c=5 t=15 l=0>
megaraid: RESET-81[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-81 cmd=a0 <c=5 t=15 l=0>
megaraid: RESET-81[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-81 cmd=a0 <c=5 t=15 l=0>
megaraid: RESET-81[7d], fw owner.
scsi: Device offlined - not ready after error recovery: host 2 channel 5 id 15 0
megaraid: ABORTING-82 cmd=12 <c=5 t=15 l=1>
megaraid: ABORTING-82[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-82 cmd=12 <c=5 t=15 l=1>
megaraid: RESET-82[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-82 cmd=12 <c=5 t=15 l=1>
megaraid: RESET-82[7d], fw owner.
megaraid: reservation reset failed.
megaraid: RESET-82 cmd=12 <c=5 t=15 l=1>
megaraid: RESET-82[7d], fw owner.
scsi: Device offlined - not ready after error recovery: host 2 channel 5 id 15 1
ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 24 (level, low) -> IRQ 24
megaraid: found 0x101e:0x1960:bus 7:slot 0:func 0
scsi3:Found MegaRAID controller at 0xf8812000, IRQ:24
megaraid: [161J:3.17] detected 0 logical drives.
megaraid: channel[0] is raid.
megaraid: channel[1] is raid.
megaraid: Cluster driver, initiator id:14
scsi3 : LSI Logic MegaRAID 161J 254 commands 16 targs 5 chans 7 luns
scsi3: scanning scsi channel 0 for logical drives.
scsi3: scanning scsi channel 1 for logical drives.
scsi3: scanning scsi channel 2 for logical drives.
scsi3: scanning scsi channel 4 [P0] for physical devices.
scsi3: scanning scsi channel 5 [P1] for physical devices.
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
SCSI device sda: 71020544 512-byte hdwr sectors (36363 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
sda: sda1 sda2
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
SCSI device sdb: 710205440 512-byte hdwr sectors (363625 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
sdb:<4>megaraid: aborted cmd 82[7d] complete.
Unable to handle kernel paging request at virtual address 3d15fa49
printing eip:
c02d3ace
*pde = 00000000
Oops: 0000 [#1]
SMP
Modules linked in:
CPU: 1
EIP: 0060:[<c02d3ace>] Not tainted VLI
EFLAGS: 00010046 (2.6.10-bruce2.6)
EIP is at mega_cmd_done+0xee/0x3a0
eax: 45445359 ebx: c199bff0 ecx: f7d1a228 edx: f7c4f400
esi: f7d07b40 edi: 0000007c ebp: f7d1a25c esp: c1973ea4
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1972000 task=c1945520)
Stack: c0500c0c c0500c0c 00000000 c18178c0 00000000 c18178c0 c199c000 f7eaa000
c18178c0 f7eab000 f7d1a228 00000001 c1973ef5 00000282 c02d396a f7d1a228
c1973ef4 00000001 00000000 0001ab50 0000007c 000005b8 00000000 bdf77930
Call Trace:
[<c02d396a>] megaraid_isr_memmapped+0xca/0x140
[<c0117c13>] scheduler_tick+0x123/0x480
[<c0136a50>] handle_IRQ_event+0x30/0x70
[<c0136b70>] __do_IRQ+0xe0/0x140
[<c0120e7a>] __do_softirq+0xba/0xd0
[<c0104b89>] do_IRQ+0x19/0x30
[<c01030b2>] common_interrupt+0x1a/0x20
[<c0100710>] default_idle+0x0/0x40
[<c010073c>] default_idle+0x2c/0x40
[<c01007cb>] cpu_idle+0x3b/0x50
Code: 4c 24 1c 8b 43 7c 89 54 24 18 89 44 24 24 eb 0d 90 90 90 90 90 90 90 90 9
<0>Kernel panic - not syncing: Fatal exception in interrupt
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-06 19:31 Mukker, Atul
2005-01-07 8:48 ` Stefan Berder
0 siblings, 1 reply; 10+ messages in thread
From: Mukker, Atul @ 2005-01-06 19:31 UTC (permalink / raw)
To: 'Stefan Berder', Mukker, Atul
Cc: 'linux-scsi@vger.kernel.org'
The target 15/Channel 1 on your first controller ( bus 5:slot 0:func 0, fw
version:[1.57] bios version:[3.13]) seems to be behaving erratically. Can
you tell me what kind of device you have on this address?
Also, why do you have two versions of the FW on your controllers?
Thanks
-Atul
> -----Original Message-----
> From: Stefan Berder [mailto:sbe@oleane.net]
> Sent: Thursday, January 06, 2005 12:14 PM
> To: Mukker, Atul
> Cc: 'linux-scsi@vger.kernel.org'
> Subject: Re: Problem with megaraid and PERC3/dc on a poweredge 6450
>
> On Thu, 6 Jan 2005 09:13:32 -0500
> "Mukker, Atul" <Atulm@lsil.com> wrote:
>
> > Thanks for the files. Both of these controllers should work
> with the
> > new drivers, megaraid_mbox and megaraid_mm. Now, I am
> waiting on the
> > kernel messages, before suggesting a prognosis. I am sure
> you know how
> > to collect the messages by re-directing them to a serial console?
>
> Done, a weird thing is that the megaraid_mm driver no more panics ...
> but it does some timeout things I don't have in 2.4.28 with megaraid2.
>
> Sorry for the noise ...
>
> Stefan
>
> --
> #=- Stefan Berder tel : 6 14 80 -=#
> #=- Ingénieur système et réseau 01 53 95 14 80 -=#
> #=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
> #=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Problem with megaraid and PERC3/dc on a poweredge 6450
2005-01-06 19:31 Mukker, Atul
@ 2005-01-07 8:48 ` Stefan Berder
0 siblings, 0 replies; 10+ messages in thread
From: Stefan Berder @ 2005-01-07 8:48 UTC (permalink / raw)
To: Mukker, Atul; +Cc: 'linux-scsi@vger.kernel.org'
On Thu, 6 Jan 2005 14:31:14 -0500
"Mukker, Atul" <Atulm@lsil.com> wrote:
> The target 15/Channel 1 on your first controller ( bus 5:slot 0:func
> 0, fw version:[1.57] bios version:[3.13]) seems to be behaving
> erratically. Can you tell me what kind of device you have on this
> address?
In fact there shouldn't be anything there ...
on the channel 0 I go 2 SCSI disks and on the channel 1 I got a 13 SCSI
disks bay, so the target 15 should be empty ...
> Also, why do you have two versions of the FW on your controllers?
I was wondering too, this box is an old one that was no more used. The
firmwares were like that at the begnining. It was my next task to
upgrade the FW too the same version.
--
#=- Stefan Berder tel : 6 14 80 -=#
#=- Ingénieur système et réseau 01 53 95 14 80 -=#
#=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
#=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
* RE: Problem with megaraid and PERC3/dc on a poweredge 6450
@ 2005-01-07 13:59 Mukker, Atul
0 siblings, 0 replies; 10+ messages in thread
From: Mukker, Atul @ 2005-01-07 13:59 UTC (permalink / raw)
To: 'Stefan Berder', Mukker, Atul
Cc: 'linux-scsi@vger.kernel.org'
Can you upgrade to the latest FW on both controllers and re-test?
-Atul Mukker
> -----Original Message-----
> From: Stefan Berder [mailto:sbe@oleane.net]
> Sent: Friday, January 07, 2005 3:48 AM
> To: Mukker, Atul
> Cc: 'linux-scsi@vger.kernel.org'
> Subject: Re: Problem with megaraid and PERC3/dc on a poweredge 6450
>
> On Thu, 6 Jan 2005 14:31:14 -0500
> "Mukker, Atul" <Atulm@lsil.com> wrote:
>
> > The target 15/Channel 1 on your first controller ( bus
> 5:slot 0:func
> > 0, fw version:[1.57] bios version:[3.13]) seems to be behaving
> > erratically. Can you tell me what kind of device you have on this
> > address?
> In fact there shouldn't be anything there ...
> on the channel 0 I go 2 SCSI disks and on the channel 1 I got
> a 13 SCSI disks bay, so the target 15 should be empty ...
>
> > Also, why do you have two versions of the FW on your controllers?
> I was wondering too, this box is an old one that was no more
> used. The firmwares were like that at the begnining. It was
> my next task to upgrade the FW too the same version.
>
> --
> #=- Stefan Berder tel : 6 14 80 -=#
> #=- Ingénieur système et réseau 01 53 95 14 80 -=#
> #=- TRANSPAC / DO-DAE-ADMG mail : sbe@oleane.net -=#
> #=- /(bb|[^b]{2})/ stefan.berder@francetelecom.com -=#
>
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2005-01-07 13:59 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-01-06 14:13 Problem with megaraid and PERC3/dc on a poweredge 6450 Mukker, Atul
2005-01-06 17:13 ` Stefan Berder
-- strict thread matches above, loose matches on Subject: below --
2005-01-07 13:59 Mukker, Atul
2005-01-06 19:31 Mukker, Atul
2005-01-07 8:48 ` Stefan Berder
2005-01-05 19:03 Mukker, Atul
2005-01-06 10:49 ` Stefan Berder
2005-01-05 17:07 Mukker, Atul
2005-01-05 18:08 ` Stefan Berder
2005-01-05 16:50 Stefan Berder
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox