Re: Linux 2.6.18-rc6

Re: Linux 2.6.18-rc6

[Olaf Hering]

[-- Attachment #1: Type: text/plain, Size: 5695 bytes --]

On Sun, Sep 03, Linus Torvalds wrote:

> 
> Things are definitely calming down, and while I'm not ready to call it a 
> final 2.6.18 yet, this migt be the last -rc.

There is a regression on LVD drives (?) since early 2.6.18rc

http://www.kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=60eef25701d25e99c991dd0f4a9f3832a0c3ad3e

I get a machine check on an older B&W G3.

<5>SCSI subsystem initialized
<6>st: Version 20050830, fixed bufsize 32768, s/g segs 256
<6>loop: loaded (max 8 devices)
<3>pmac_zilog 0.00013000:ch-b: irda_setup timed out on get_version byte
<6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<4>        <Adaptec 2940B Ultra2 SCSI adapter>
<4>        aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
<4>
<5>  Vendor: IBM       Model: DDRS-39130D       Rev: DC2A
<5>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
<6> target0:0:0: Beginning Domain Validation
<6> target0:0:0: wide asynchronous
<4>Machine check in kernel mode.
<4>Caused by (from SRR1=49030): Transfer error ack signal
<4>Oops: Machine check, sig: 7 [#1]
<4>
<4>Modules linked in: aic7xxx scsi_transport_spi cpufreq_ondemand loop nfs nfs_acl lockd sunrpc sg st sd_mod sr_mod scsi_mod ide_cd cdrom
<4>NIP: D21F03A0 LR: D20D9494 CTR: D21F0388
<4>REGS: cf5059f0 TRAP: 0200   Not tainted  (2.6.18-rc6-20060905-default)
<4>MSR: 00049030 <EE,ME,IR,DR>  CR: 22022242  XER: 00000000
<4>TASK = cf1d9990[963] 'insmod' THREAD: cf504000
<6>GPR00: 000000FF CF505AA0 CF1D9990 CF513400 CF505A6C CF564C00 CF564D00 00000000 
<6>GPR08: 00000001 D105C000 CF64D400 00000000 F2841C80 100290EC 0000000F D22BFB50 
<6>GPR16: 0000001E D229EDD0 CFC52500 D229EDA8 CF5139CC CF513818 CF5138BC CF513400 
<6>GPR24: CF513800 CF5139A0 FFFFFFFF C37C0000 CF5139A0 CF513800 CF513000 CF513C00 
<4>NIP [D21F03A0] ahc_linux_get_signalling+0x18/0xa8 [aic7xxx]
<4>LR [D20D9494] spi_dv_device+0x338/0x51c [scsi_transport_spi]
<4>Call Trace:
<4>[CF505AA0] [D20D9364] spi_dv_device+0x208/0x51c [scsi_transport_spi] (unreliable)
<4>[CF505AF0] [D21F0808] ahc_linux_slave_configure+0xfc/0x114 [aic7xxx]
<4>[CF505B30] [D20B71D8] scsi_probe_and_add_lun+0x8d4/0xa40 [scsi_mod]
<4>[CF505B90] [D20B78F8] __scsi_scan_target+0xd8/0x630 [scsi_mod]
<4>[CF505C20] [D20B7E9C] scsi_scan_channel+0x4c/0x9c [scsi_mod]
<4>[CF505C40] [D20B7FD4] scsi_scan_host_selected+0xe8/0x140 [scsi_mod]
<4>[CF505C70] [D21F3998] ahc_linux_register_host+0x344/0x35c [aic7xxx]
<4>[CF505D10] [D21F468C] ahc_linux_pci_dev_probe+0x1a8/0x1c8 [aic7xxx]
<4>[CF505D80] [C016A49C] pci_device_probe+0x6c/0xa0
<4>[CF505DA0] [C01F0AF4] driver_probe_device+0x60/0xf4
<4>[CF505DC0] [C01F0CC4] __driver_attach+0x8c/0xf0
<4>[CF505DE0] [C01F0424] bus_for_each_dev+0x50/0x94
<4>[CF505E10] [C01F0A08] driver_attach+0x24/0x34
<4>[CF505E20] [C01F000C] bus_add_driver+0x78/0x128
<4>[CF505E40] [C01F0FC4] driver_register+0xa0/0xb4
<4>[CF505E50] [C016A2C8] __pci_register_driver+0x4c/0x8c
<4>[CF505E60] [D21F44CC] ahc_linux_pci_init+0x20/0x38 [aic7xxx]
<4>[CF505E70] [D105A3C0] ahc_linux_init+0x3c0/0x530 [aic7xxx]
<4>[CF505EA0] [C004EB50] sys_init_module+0x1368/0x14f8
<4>[CF505F40] [C00125A4] ret_from_syscall+0x0/0x40
<4>--- Exception: c01 at 0xff698a4
<4>    LR = 0x10001100
<4>Instruction dump:
<4>38600000 4e800020 38600000 4e800020 4e800020 4e800020 814302ac 800a0000 
<4>2f800000 409e0018 812a0004 8809001f <0c000000> 4c00012c 48000028 812a0004 
<4> scsi0: PCI error Interrupt at seqaddr = 0x8
<4>scsi0: Signaled a Target Abort


Here is the dmesg from a working 2.6.16 kernel:

...
SCSI subsystem initialized
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
        <Adaptec 2940B Ultra2 SCSI adapter>
        aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs

  Vendor: IBM       Model: DDRS-39130D       Rev: DC2A
  Type:   Direct-Access                      ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
 target0:0:0: Beginning Domain Validation
 target0:0:0: wide asynchronous
 target0:0:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
 target0:0:0: Domain Validation skipping write tests
 target0:0:0: Ending Domain Validation
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
sda: Write Protect is off
sda: Mode Sense: e5 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
sda: Write Protect is off
sda: Mode Sense: e5 00 00 08
SCSI device sda: drive cache: write back
 sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
  Vendor: IBM       Model: DNES-318350W      Rev: SA30
  Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:2:0: Tagged Queuing enabled.  Depth 32
 target0:0:2: Beginning Domain Validation
 target0:0:2: wide asynchronous
 target0:0:2: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
 target0:0:2: Domain Validation skipping write tests
 target0:0:2: Ending Domain Validation
SCSI device sdb: 35843670 512-byte hdwr sectors (18352 MB)
sdb: Write Protect is off
sdb: Mode Sense: c3 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 35843670 512-byte hdwr sectors (18352 MB)
sdb: Write Protect is off
sdb: Mode Sense: c3 00 00 08
SCSI device sdb: drive cache: write back
 sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sdb13
sd 0:0:2:0: Attached scsi disk sdb
sd 0:0:2:0: Attached scsi generic sg1 type 0
mesh: configured for synchronous 5 MB/s
mesh: performing initial bus reset...
scsi1 : MESH
ReiserFS: sda4: found reiserfs format "3.6" with standard journal
ReiserFS: sda4: using ordered data mode
...


[-- Attachment #2: boot.msg --]
[-- Type: text/plain, Size: 11378 bytes --]

<6>Using PowerMac machine description
<4>Total memory = 256MB; using 512kB for hash table (at cff80000)
<5>Linux version 2.6.18-rc6-20060905-default (geeko@buildhost) (gcc version 4.1.2 20060731 (prerelease) (SUSE Linux)) #1 Sun Sep 3 10:14:34 UTC 2006
<4>Found initrd at 0xc3086000:0xc36574f8
<6>Found a Paddington mac-io controller, rev: 0, mapped at 0xfdf80000
<6>PowerMac motherboard: Blue&White G3
<6>Found Grackle (MPC106) PCI host bridge at 0x0000000080000000. Firmware bus number: 0->1
<4>nvram: OF partition at 0x140
<4>nvram: XP partition at 0x11b0
<4>nvram: NR partition at 0x12b0
<7>Top of RAM: 0x10000000, Total RAM: 0x10000000
<7>Memory hole size: 0MB
<7>On node 0 totalpages: 65536
<7>  DMA zone: 65536 pages, LIFO batch:15
<4>Built 1 zonelists.  Total pages: 65536
<5>Kernel command line: root=/dev/sda4  quiet sysrq=1 video=aty128fb:1024x768@85 
<6>irq: Found primary Apple PIC /pci@80000000/pci-bridge@d/mac-io@5 for 64 irqs
<6>irq: System has 64 possible interrupts
<4>PID hash table entries: 2048 (order: 11, 8192 bytes)
<4>GMT Delta read from XPRAM: 0 minutes, DST: off
<7>time_init: decrementer frequency = 24.934500 MHz
<7>time_init: processor frequency   = 400.000000 MHz
<4>Console: colour dummy device 80x25
<4>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<7>High memory: 0k
<6>Memory: 248320k/262144k available (3588k kernel code, 13628k reserved, 524k data, 452k bss, 192k init)
<7>Calibrating delay loop... 49.79 BogoMIPS (lpj=99584)
<6>Security Framework v1.0.0 initialized
<4>Mount-cache hash table entries: 512
<4>device-tree: Duplicate name in /cpus/PowerPC,750@0, renamed to "l2-cache#1"
<6>checking if image is initramfs... it is
<4>Freeing initrd memory: 5957k freed
<6>NET: Registered protocol family 16
<6>PCI: Probing PCI hardware
<3>PCI: Cannot allocate resource region 0 of PCI bridge 1
<6>PCI: bridge 1 resource 0 moved to 7ff000..7fffff
<3>PCI: Cannot allocate resource region 0 of device 0000:01:01.0
<3>PCI: Cannot allocate resource region 1 of device 0000:01:01.0
<3>PCI: Cannot allocate resource region 2 of device 0000:01:01.0
<3>PCI: Cannot allocate resource region 3 of device 0000:01:01.0
<3>PCI: Cannot allocate resource region 4 of device 0000:01:01.0
<3>PCI: Cannot allocate resource region 1 of device 0000:00:10.0
<3>PCI: Cannot allocate resource region 0 of device 0000:01:04.0
<4>PCI: Enabling device 0000:01:04.0 (0010 -> 0013)
<7>Registering pmac pic with sysfs...
<6>usbcore: registered new driver usbfs
<6>usbcore: registered new driver hub
<6>NET: Registered protocol family 2
<4>IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
<4>TCP established hash table entries: 8192 (order: 3, 32768 bytes)
<4>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP: Hash tables configured (established 8192 bind 4096)
<6>TCP reno registered
<4>Thermal assist unit using timers, shrink_timer: 500 jiffies
<6>audit: initializing netlink socket (disabled)
<5>audit(1157465930.056:1): initialized
<5>VFS: Disk quotas dquot_6.5.1
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>Initializing Cryptographic API
<6>io scheduler noop registered
<6>io scheduler anticipatory registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<4>PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
<6>aty128fb: Found Open Firmware ROM Image
<6>aty128fb: BIOS not located, guessing timings.
<6>aty128fb: Rage128 RE PCI [chip rev 0x2] 16M 128-bit SDR SGRAM (1:1)
<4>Console: switching to colour frame buffer device 128x48
<6>fb0: ATY Rage128 frame buffer device on Rage128 RE PCI
<6>Generic RTC Driver v1.07
<6>Macintosh non-volatile memory driver v1.1
<6>pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
<6>ttyS0 at MMIO 0x80813020 (irq = 16) is a Z85c30 ESCC - Serial port
<6>ttyS1 at MMIO 0x80813000 (irq = 17) is a Z85c30 ESCC - Infrared port
<4>RAMDISK driver initialized: 16 RAM disks of 123456K size 1024 blocksize
<6>MacIO PCI driver attached to Paddington chipset
<4>Can't request resource 0 for MacIO device 0.00000000:power-mg
<6>input: Macintosh mouse button emulation as /class/input/input0
<4>Macintosh CUDA driver v0.5 for Unified ADB.
<6>apm_emu: Requires a machine with a PMU.
<6>adb: starting probe task...
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>CMD646: IDE controller at PCI slot 0000:01:01.0
<6>CMD646: chipset revision 7
<6>CMD646: chipset revision 0x07, UltraDMA Capable
<6>CMD646: 100% native mode on irq 26
<6>    ide0: BM-DMA at 0x7ff020-0x7ff027, BIOS settings: hda:pio, hdb:pio
<6>    ide1: BM-DMA at 0x7ff028-0x7ff02f, BIOS settings: hdc:pio, hdd:pio
<7>Probing IDE interface ide0...
<7>adb devices:
<6>adb: finished probe task...
<7>Probing IDE interface ide1...
<6>ide2: Found Apple Heathrow ATA controller, bus ID 0, irq 32
<7>Probing IDE interface ide2...
<4>hde: MATSHITAPD-2 LF-D110, ATAPI CD/DVD-ROM drive
<4>hdf: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
<6>hde: Enabling MultiWord DMA 2
<4>ide2 at 0xd101c000-0xd101c007,0xd101c160 on irq 32
<7>Probing IDE interface ide0...
<7>Probing IDE interface ide1...
<7>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
<6>ohci_hcd 0000:01:06.0: OHCI Host Controller
<6>ohci_hcd 0000:01:06.0: new USB bus registered, assigned bus number 1
<6>ohci_hcd 0000:01:06.0: irq 28, io mem 0x80880000
<6>usb usb1: new device found, idVendor=0000, idProduct=0000
<6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: OHCI Host Controller
<6>usb usb1: Manufacturer: Linux 2.6.18-rc6-20060905-default ohci_hcd
<6>usb usb1: SerialNumber: 0000:01:06.0
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>usb 1-2: new full speed USB device using ohci_hcd and address 2
<6>usb 1-2: new device found, idVendor=05ac, idProduct=1001
<6>usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2: Product: Hub in Apple USB Keyboard
<6>usb 1-2: Manufacturer: Alps Electric
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>hub 1-2:1.0: USB hub found
<6>hub 1-2:1.0: 3 ports detected
<6>usb 1-2.1: new low speed USB device using ohci_hcd and address 3
<6>usb 1-2.1: new device found, idVendor=05ac, idProduct=0202
<6>usb 1-2.1: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2.1: Product: Apple USB Keyboard
<6>usb 1-2.1: Manufacturer: Alps Electric
<6>usb 1-2.1: configuration #1 chosen from 1 choice
<6>usb 1-2.2: new low speed USB device using ohci_hcd and address 4
<6>usb 1-2.2: new device found, idVendor=05ac, idProduct=0307
<6>usb 1-2.2: new device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-2.2: Product: Apple Optical USB Mouse
<6>usb 1-2.2: Manufacturer: Logitech
<6>usb 1-2.2: configuration #1 chosen from 1 choice
<6>usbcore: registered new driver hiddev
<6>input: Alps Electric Apple USB Keyboard as /class/input/input1
<6>input: USB HID v1.00 Keyboard [Alps Electric Apple USB Keyboard] on usb-0000:01:06.0-2.1
<6>input: Logitech Apple Optical USB Mouse as /class/input/input2
<6>input: USB HID v1.10 Mouse [Logitech Apple Optical USB Mouse] on usb-0000:01:06.0-2.2
<6>usbcore: registered new driver usbhid
<6>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
<6>usbcore: registered new driver appletouch
<6>mice: PS/2 mouse device common for all mice
<6>md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
<6>md: bitmap version 4.39
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 17
<4>Freeing unused kernel memory: 192k init
<6>hde: ATAPI DVD-ROM DVD-RAM drive, 2048kB Cache, DMA
<6>Uniform CD-ROM driver Revision: 3.20
<5>SCSI subsystem initialized
<6>st: Version 20050830, fixed bufsize 32768, s/g segs 256
<6>loop: loaded (max 8 devices)
<3>pmac_zilog 0.00013000:ch-b: irda_setup timed out on get_version byte
<6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<4>        <Adaptec 2940B Ultra2 SCSI adapter>
<4>        aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
<4>
<5>  Vendor: IBM       Model: DDRS-39130D       Rev: DC2A
<5>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
<6> target0:0:0: Beginning Domain Validation
<6> target0:0:0: wide asynchronous
<4>Machine check in kernel mode.
<4>Caused by (from SRR1=49030): Transfer error ack signal
<4>Oops: Machine check, sig: 7 [#1]
<4>
<4>Modules linked in: aic7xxx scsi_transport_spi cpufreq_ondemand loop nfs nfs_acl lockd sunrpc sg st sd_mod sr_mod scsi_mod ide_cd cdrom
<4>NIP: D21F03A0 LR: D20D9494 CTR: D21F0388
<4>REGS: cf5059f0 TRAP: 0200   Not tainted  (2.6.18-rc6-20060905-default)
<4>MSR: 00049030 <EE,ME,IR,DR>  CR: 22022242  XER: 00000000
<4>TASK = cf1d9990[963] 'insmod' THREAD: cf504000
<6>GPR00: 000000FF CF505AA0 CF1D9990 CF513400 CF505A6C CF564C00 CF564D00 00000000 
<6>GPR08: 00000001 D105C000 CF64D400 00000000 F2841C80 100290EC 0000000F D22BFB50 
<6>GPR16: 0000001E D229EDD0 CFC52500 D229EDA8 CF5139CC CF513818 CF5138BC CF513400 
<6>GPR24: CF513800 CF5139A0 FFFFFFFF C37C0000 CF5139A0 CF513800 CF513000 CF513C00 
<4>NIP [D21F03A0] ahc_linux_get_signalling+0x18/0xa8 [aic7xxx]
<4>LR [D20D9494] spi_dv_device+0x338/0x51c [scsi_transport_spi]
<4>Call Trace:
<4>[CF505AA0] [D20D9364] spi_dv_device+0x208/0x51c [scsi_transport_spi] (unreliable)
<4>[CF505AF0] [D21F0808] ahc_linux_slave_configure+0xfc/0x114 [aic7xxx]
<4>[CF505B30] [D20B71D8] scsi_probe_and_add_lun+0x8d4/0xa40 [scsi_mod]
<4>[CF505B90] [D20B78F8] __scsi_scan_target+0xd8/0x630 [scsi_mod]
<4>[CF505C20] [D20B7E9C] scsi_scan_channel+0x4c/0x9c [scsi_mod]
<4>[CF505C40] [D20B7FD4] scsi_scan_host_selected+0xe8/0x140 [scsi_mod]
<4>[CF505C70] [D21F3998] ahc_linux_register_host+0x344/0x35c [aic7xxx]
<4>[CF505D10] [D21F468C] ahc_linux_pci_dev_probe+0x1a8/0x1c8 [aic7xxx]
<4>[CF505D80] [C016A49C] pci_device_probe+0x6c/0xa0
<4>[CF505DA0] [C01F0AF4] driver_probe_device+0x60/0xf4
<4>[CF505DC0] [C01F0CC4] __driver_attach+0x8c/0xf0
<4>[CF505DE0] [C01F0424] bus_for_each_dev+0x50/0x94
<4>[CF505E10] [C01F0A08] driver_attach+0x24/0x34
<4>[CF505E20] [C01F000C] bus_add_driver+0x78/0x128
<4>[CF505E40] [C01F0FC4] driver_register+0xa0/0xb4
<4>[CF505E50] [C016A2C8] __pci_register_driver+0x4c/0x8c
<4>[CF505E60] [D21F44CC] ahc_linux_pci_init+0x20/0x38 [aic7xxx]
<4>[CF505E70] [D105A3C0] ahc_linux_init+0x3c0/0x530 [aic7xxx]
<4>[CF505EA0] [C004EB50] sys_init_module+0x1368/0x14f8
<4>[CF505F40] [C00125A4] ret_from_syscall+0x0/0x40
<4>--- Exception: c01 at 0xff698a4
<4>    LR = 0x10001100
<4>Instruction dump:
<4>38600000 4e800020 38600000 4e800020 4e800020 4e800020 814302ac 800a0000 
<4>2f800000 409e0018 812a0004 8809001f <0c000000> 4c00012c 48000028 812a0004 
<4> scsi0: PCI error Interrupt at seqaddr = 0x8
<4>scsi0: Signaled a Target Abort
<6>mesh: configured for synchronous 5 MB/s
<6>mesh: performing initial bus reset...
<6>scsi1 : MESH
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new driver usb-storage
<6>USB Mass Storage support registered.
<7>ieee1394: Initialized config rom entry `ip1394'
<6>ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
<6>ieee1394: sbp2: Try serialize_io=0 for better performance
<6>eth0: BMAC+ at 00:50:e4:30:77:1f

Re: Linux 2.6.18-rc6

[James Bottomley]

On Tue, 2006-09-05 at 14:26 +0200, Olaf Hering wrote:
> <4>Machine check in kernel mode.
> <4>Caused by (from SRR1=49030): Transfer error ack signal
> <4>Oops: Machine check, sig: 7 [#1]
[...]
> <4> scsi0: PCI error Interrupt at seqaddr = 0x8

Is this actually a PCI bus error?  In which case it's probably the
ahc_inb(,SBLKCTL) of ahc_linux_get_signalling().  Can you verify this?
And what happens when you try to cat /proc/scsi_host/host<n>/signalling
for this card?

James

Re: Linux 2.6.18-rc6

[Benjamin Herrenschmidt]

On Tue, 2006-09-05 at 16:01 -0500, James Bottomley wrote:
> On Tue, 2006-09-05 at 14:26 +0200, Olaf Hering wrote:
> > <4>Machine check in kernel mode.
> > <4>Caused by (from SRR1=49030): Transfer error ack signal
> > <4>Oops: Machine check, sig: 7 [#1]
> [...]
> > <4> scsi0: PCI error Interrupt at seqaddr = 0x8
> 
> Is this actually a PCI bus error?  In which case it's probably the
> ahc_inb(,SBLKCTL) of ahc_linux_get_signalling().  Can you verify this?
> And what happens when you try to cat /proc/scsi_host/host<n>/signalling
> for this card?

Yes, it's a PCI error.

Ben.

Re: Linux 2.6.18-rc6

[James Bottomley]

On Wed, 2006-09-06 at 08:20 +1000, Benjamin Herrenschmidt wrote:
> Yes, it's a PCI error.

Thanks, and the cat of /proc/scsi_host/host<n>/signalling?

My suspicion is the register doesn't actually exist on this card so it
doesn't actually respond on the bus.  However, on my equivalent
everything works; largely I think because the only PC's I have don't
know how to signal a PCI error.

James

Re: Linux 2.6.18-rc6

[Benjamin Herrenschmidt]

On Tue, 2006-09-05 at 18:22 -0500, James Bottomley wrote:
> On Wed, 2006-09-06 at 08:20 +1000, Benjamin Herrenschmidt wrote:
> > Yes, it's a PCI error.
> 
> Thanks, and the cat of /proc/scsi_host/host<n>/signalling?
> 
> My suspicion is the register doesn't actually exist on this card so it
> doesn't actually respond on the bus.  However, on my equivalent
> everything works; largely I think because the only PC's I have don't
> know how to signal a PCI error.

Olaf will tell us (I don't have the hardware) but it's indeed a typical
thing .... From my experience, Adaptec tend to very easily throw PCI
aborts at you if it doesn't like something in a register access (which
isn't necessarily a bad thing btw, other vendors are more lenient tho),
and Macs are well known to Machine Check the box when getting a PCI
error while most x86 boxes silently ignore them...

Ben.

Re: Linux 2.6.18-rc6

[Olaf Hering]

On Tue, Sep 05, James Bottomley wrote:

> On Tue, 2006-09-05 at 14:26 +0200, Olaf Hering wrote:
> > <4>Machine check in kernel mode.
> > <4>Caused by (from SRR1=49030): Transfer error ack signal
> > <4>Oops: Machine check, sig: 7 [#1]
> [...]
> > <4> scsi0: PCI error Interrupt at seqaddr = 0x8
> 
> Is this actually a PCI bus error?  In which case it's probably the
> ahc_inb(,SBLKCTL) of ahc_linux_get_signalling().  Can you verify this?
> And what happens when you try to cat /proc/scsi_host/host<n>/signalling
> for this card?

This causes another machine check because it runs ahc_inb(ahc, SBLKCTL) again.
With debug I get:

CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=32
CONFIG_AIC7XXX_RESET_DELAY_MS=5000
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=2047
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y


<4>ahc_pci:1:4:0: hardware scb 64 bytes; kernel scb 52 bytes; ahc_dma 8 bytes
<6>scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<4>        <Adaptec 2940B Ultra2 SCSI adapter>
<4>        aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
<4>
<5>  Vendor: IBM       Model: DDRS-39130D       Rev: DC2A
<5>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
<6> target0:0:0: Beginning Domain Validation
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0xc0
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x20
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x2
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_OUT PHASEMIS in Message-in phase
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x2
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x3
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1
<4>scsi0:A:0:0: Asserting ATN for response
<4>scsi0:A:0:0: INITIATOR_MSG_IN PHASEMIS in Message-out phase
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x3
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x45
<4>scsi0:A:0:0: INITIATOR_MSG_OUT byte 0x0
<4>scsi0:A:0:0: INITIATOR_MSG_OUT PHASEMIS in Message-in phase
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x3
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x1
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x45
<4>scsi0:A:0:0: INITIATOR_MSG_IN byte 0x0
<6> target0:0:0: wide asynchronous
<4>scsi0:A:0:0: INITIATOR_MSG_IN PHASEMIS in Command phase
<4>Machine check in kernel mode.
<4>Caused by (from SRR1=49030): Transfer error ack signal
<4>Oops: Machine check, sig: 7 [#1]
<4>
<4>Modules linked in: aic7xxx scsi_transport_spi cpufreq_ondemand loop nfs nfs_acl lockd sunrpc sg st sd_mod sr_mod scsi_mod ide_cd cdrom
<4>NIP: D21F0604 LR: D20D9494 CTR: D21F05EC
<4>REGS: cf80d9f0 TRAP: 0200   Not tainted  (2.6.18-rc6-20060905-default)
<4>MSR: 00049030 <EE,ME,IR,DR>  CR: 22022242  XER: 00000000
<4>TASK = cf7e8760[963] 'insmod' THREAD: cf80c000
<6>GPR00: 000000FF CF80DAA0 CF7E8760 CEA58400 CF80DA6C CEA58000 CEA58100 00000000
<6>GPR08: 00000001 D105C000 CF6E3C00 00000000 2155D240 100290EC 0000000F D22C0498
<6>GPR16: 0000001E D229F258 C373D500 D229F230 CEA589CC CEA58818 CEA588BC CEA58400
<6>GPR24: CEA58800 CEA589A0 FFFFFFFF C37C2000 CEA589A0 CEA58800 CEA59C00 CEA58C00
<4>NIP [D21F0604] ahc_linux_get_signalling+0x18/0xa8 [aic7xxx]
<4>LR [D20D9494] spi_dv_device+0x338/0x51c [scsi_transport_spi]
<4>Call Trace:
<4>[CF80DAA0] [D20D9364] spi_dv_device+0x208/0x51c [scsi_transport_spi] (unreliable)
<4>[CF80DAF0] [D21F0A6C] ahc_linux_slave_configure+0xfc/0x114 [aic7xxx]
<4>[CF80DB30] [D20B71D8] scsi_probe_and_add_lun+0x8d4/0xa40 [scsi_mod]
<4>[CF80DB90] [D20B78F8] __scsi_scan_target+0xd8/0x630 [scsi_mod]
<4>[CF80DC20] [D20B7E9C] scsi_scan_channel+0x4c/0x9c [scsi_mod]
<4>[CF80DC40] [D20B7FD4] scsi_scan_host_selected+0xe8/0x140 [scsi_mod]
<4>[CF80DC70] [D21F3CA4] ahc_linux_register_host+0x344/0x35c [aic7xxx]
<4>[CF80DD10] [D21F4998] ahc_linux_pci_dev_probe+0x1a8/0x1c8 [aic7xxx]
<4>[CF80DD80] [C016A49C] pci_device_probe+0x6c/0xa0
<4>[CF80DDA0] [C01F0AF4] driver_probe_device+0x60/0xf4
<4>[CF80DDC0] [C01F0CC4] __driver_attach+0x8c/0xf0
<4>[CF80DDE0] [C01F0424] bus_for_each_dev+0x50/0x94
<4>[CF80DE10] [C01F0A08] driver_attach+0x24/0x34
<4>[CF80DE20] [C01F000C] bus_add_driver+0x78/0x128
<4>[CF80DE40] [C01F0FC4] driver_register+0xa0/0xb4
<4>[CF80DE50] [C016A2C8] __pci_register_driver+0x4c/0x8c
<4>[CF80DE60] [D21F47D8] ahc_linux_pci_init+0x20/0x38 [aic7xxx]
<4>[CF80DE70] [D105A3C0] ahc_linux_init+0x3c0/0x530 [aic7xxx]
<4>[CF80DEA0] [C004EB50] sys_init_module+0x1368/0x14f8
<4>[CF80DF40] [C00125A4] ret_from_syscall+0x0/0x40
<4>--- Exception: c01 at 0xff698a4
<4>    LR = 0x10001100
<4>Instruction dump:
<4>38600000 4e800020 38600000 4e800020 4e800020 4e800020 814302ac 800a0000
<4>2f800000 409e0018 812a0004 8809001f <0c000000> 4c00012c 48000028 812a0004
<4> scsi0: PCI error Interrupt at seqaddr = 0x8
<4>scsi0: Signaled a Target Abort

Re: Linux 2.6.18-rc6

[Olaf Hering]

On Tue, Sep 05, James Bottomley wrote:

> On Wed, 2006-09-06 at 08:20 +1000, Benjamin Herrenschmidt wrote:
> > Yes, it's a PCI error.
> 
> Thanks, and the cat of /proc/scsi_host/host<n>/signalling?
> 
> My suspicion is the register doesn't actually exist on this card so it
> doesn't actually respond on the bus.  However, on my equivalent
> everything works; largely I think because the only PC's I have don't
> know how to signal a PCI error.

Where is that area mapped?
It crashes already if I read port 0.
Everything works if I also add the second hunk to disable signalling.

Index: linux-2.6.17/drivers/scsi/aic7xxx/aic7xxx_osm.c
===================================================================
--- linux-2.6.17.orig/drivers/scsi/aic7xxx/aic7xxx_osm.c
+++ linux-2.6.17/drivers/scsi/aic7xxx/aic7xxx_osm.c
@@ -2539,8 +2539,15 @@ static void ahc_linux_set_iu(struct scsi
 static void ahc_linux_get_signalling(struct Scsi_Host *shost)
 {
        struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata;
-       u8 mode = ahc_inb(ahc, SBLKCTL);
+       int i;
+       u8 mode;
+       for (i=0;i!=SBLKCTL;i++) {
+               printk("i 0x%02x ",i);
+               mode = ahc_inb(ahc, i);
+               printk("m 0x%02x\n",mode);
 
+       }
+       mode = ahc_inb(ahc, SBLKCTL);
        if (mode & ENAB40)
                spi_signalling(shost) = SPI_SIGNAL_LVD;
        else if (mode & ENAB20)
@@ -2566,8 +2573,8 @@ static struct spi_function_template ahc_
        .show_iu        = 1,
        .set_qas        = ahc_linux_set_qas,
        .show_qas       = 1,
-#endif
        .get_signalling = ahc_linux_get_signalling,
+#endif
 };
 
 

Re: Linux 2.6.18-rc6

[James Bottomley]

On Wed, 2006-09-06 at 13:01 +0200, Olaf Hering wrote:
> This causes another machine check because it runs ahc_inb(ahc, SBLKCTL) again.
> With debug I get:

Exactly.  It's not a card state problem; the register simply doesn't
exist.  It looks like from the source code, it only exists on twin or U2
and above chipsets (i.e. those supporting LVD).

Try this patch, which should deduce the bus type for U and below without
resorting to the SBLKCTL register.

James

diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.c b/drivers/scsi/aic7xxx/aic7xxx_osm.c
index e5bb4d8..0b3c01a 100644
--- a/drivers/scsi/aic7xxx/aic7xxx_osm.c
+++ b/drivers/scsi/aic7xxx/aic7xxx_osm.c
@@ -2539,15 +2539,23 @@ #endif
 static void ahc_linux_get_signalling(struct Scsi_Host *shost)
 {
 	struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata;
-	u8 mode = ahc_inb(ahc, SBLKCTL);
+	u8 mode;
 
-	if (mode & ENAB40)
-		spi_signalling(shost) = SPI_SIGNAL_LVD;
-	else if (mode & ENAB20)
+	if (!(ahc->features & AHC_ULTRA2)) {
+		/* non-LVD chipset, may not have SBLKCTL reg */
 		spi_signalling(shost) = 
 			ahc->features & AHC_HVD ?
 			SPI_SIGNAL_HVD :
 			SPI_SIGNAL_SE;
+		return;
+	}
+
+	mode = ahc_inb(ahc, SBLKCTL);
+
+	if (mode & ENAB40)
+		spi_signalling(shost) = SPI_SIGNAL_LVD;
+	else if (mode & ENAB20)
+		spi_signalling(shost) = SPI_SIGNAL_SE;
 	else
 		spi_signalling(shost) = SPI_SIGNAL_UNKNOWN;
 }

Re: Linux 2.6.18-rc6

[Olaf Hering]

On Wed, Sep 06, James Bottomley wrote:

> On Wed, 2006-09-06 at 13:01 +0200, Olaf Hering wrote:
> > This causes another machine check because it runs ahc_inb(ahc, SBLKCTL) again.
> > With debug I get:
> 
> Exactly.  It's not a card state problem; the register simply doesn't
> exist.  It looks like from the source code, it only exists on twin or U2
> and above chipsets (i.e. those supporting LVD).
> 
> Try this patch, which should deduce the bus type for U and below without
> resorting to the SBLKCTL register.
> 
> James
> 
> diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.c b/drivers/scsi/aic7xxx/aic7xxx_osm.c
> index e5bb4d8..0b3c01a 100644
> --- a/drivers/scsi/aic7xxx/aic7xxx_osm.c
> +++ b/drivers/scsi/aic7xxx/aic7xxx_osm.c
> @@ -2539,15 +2539,23 @@ #endif
>  static void ahc_linux_get_signalling(struct Scsi_Host *shost)
>  {
>  	struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata;
> -	u8 mode = ahc_inb(ahc, SBLKCTL);
> +	u8 mode;
>  
> -	if (mode & ENAB40)
> -		spi_signalling(shost) = SPI_SIGNAL_LVD;
> -	else if (mode & ENAB20)
> +	if (!(ahc->features & AHC_ULTRA2)) {

This does not work: ahc_linux_get_signalling: f 56f6

echo $(( 0x56f6 & 0x00002 )) gives 2, and the ahc_inb is called.

Re: Linux 2.6.18-rc6

[James Bottomley]

On Thu, 2006-09-07 at 11:15 +0200, Olaf Hering wrote:
> This does not work: ahc_linux_get_signalling: f 56f6
> 
> echo $(( 0x56f6 & 0x00002 )) gives 2, and the ahc_inb is called.

Erm, there's something else going on then:  An ultra 2 card has to have
this register.  It's used to signal mode changes in
ahc_handle_scsiint().  The piece of code in there will trigger and read
this register for any ultra 2 + controller every time there's an error
(just to see if the bus mode changed).

James

Re: Linux 2.6.18-rc6

[Doug Ledford]

[-- Attachment #1: Type: text/plain, Size: 1120 bytes --]

On Thu, 2006-09-07 at 09:04 -0500, James Bottomley wrote:
> On Thu, 2006-09-07 at 11:15 +0200, Olaf Hering wrote:
> > This does not work: ahc_linux_get_signalling: f 56f6
> > 
> > echo $(( 0x56f6 & 0x00002 )) gives 2, and the ahc_inb is called.
> 
> Erm, there's something else going on then:  An ultra 2 card has to have
> this register.  It's used to signal mode changes in
> ahc_handle_scsiint().  The piece of code in there will trigger and read
> this register for any ultra 2 + controller every time there's an error
> (just to see if the bus mode changed).

Sorry for my belated response, but this usually happens when you access
an aic chipset too soon after a chip reset.  Try putting a delay before
whatever access is causing this to see if it make s difference.  Common
problems include after a chip reset, touching any register will cause
the card to reset, etc.

-- 
Doug Ledford <dledford@redhat.com>
              GPG KeyID: CFBFF194
              http://people.redhat.com/dledford

Infiniband specific RPMs available at
              http://people.redhat.com/dledford/Infiniband

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]

Re: Linux 2.6.18-rc6

[Olaf Hering]

On Fri, Sep 15, Doug Ledford wrote:

> Sorry for my belated response, but this usually happens when you access
> an aic chipset too soon after a chip reset.  Try putting a delay before
> whatever access is causing this to see if it make s difference.  Common
> problems include after a chip reset, touching any register will cause
> the card to reset, etc.

I put a ssleep(1) before the ahc_inb(ahc, SBLKCTL);
Does not help. Is it possible that the card loses some of its features
during reset and something needs to be done to reenable them?

Re: Linux 2.6.18-rc6

[Olaf Hering]

On Fri, Sep 15, Doug Ledford wrote:

> On Thu, 2006-09-07 at 09:04 -0500, James Bottomley wrote:
> > On Thu, 2006-09-07 at 11:15 +0200, Olaf Hering wrote:
> > > This does not work: ahc_linux_get_signalling: f 56f6
> > > 
> > > echo $(( 0x56f6 & 0x00002 )) gives 2, and the ahc_inb is called.
> > 
> > Erm, there's something else going on then:  An ultra 2 card has to have
> > this register.  It's used to signal mode changes in
> > ahc_handle_scsiint().  The piece of code in there will trigger and read
> > this register for any ultra 2 + controller every time there's an error
> > (just to see if the bus mode changed).
> 
> Sorry for my belated response, but this usually happens when you access
> an aic chipset too soon after a chip reset.  Try putting a delay before
> whatever access is causing this to see if it make s difference.  Common
> problems include after a chip reset, touching any register will cause
> the card to reset, etc.

As pointed out in private mail, this patch fixes the machine check for
me. Thanks Doug.

Maybe the AHC_ULTRA2 feature check is needed as well for other cards.

---
 drivers/scsi/aic7xxx/aic7xxx_osm.c |    9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

Index: linux-2.6.18-rc7/drivers/scsi/aic7xxx/aic7xxx_osm.c
===================================================================
--- linux-2.6.18-rc7.orig/drivers/scsi/aic7xxx/aic7xxx_osm.c
+++ linux-2.6.18-rc7/drivers/scsi/aic7xxx/aic7xxx_osm.c
@@ -2539,7 +2539,14 @@ static void ahc_linux_set_iu(struct scsi
 static void ahc_linux_get_signalling(struct Scsi_Host *shost)
 {
 	struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata;
-	u8 mode = ahc_inb(ahc, SBLKCTL);
+	unsigned long flags;
+	u8 mode;
+
+	ahc_lock(ahc, &flags);
+	ahc_pause(ahc);
+	mode = ahc_inb(ahc, SBLKCTL);
+	ahc_unpause(ahc);
+	ahc_unlock(ahc, &flags);
 
 	if (mode & ENAB40)
 		spi_signalling(shost) = SPI_SIGNAL_LVD;

Re: Linux 2.6.18-rc6

[James Bottomley]

On Sun, 2006-09-17 at 07:38 +0200, Olaf Hering wrote:
> As pointed out in private mail, this patch fixes the machine check for
> me. Thanks Doug.
> 
> Maybe the AHC_ULTRA2 feature check is needed as well for other cards.

It is ... the non ULTRA2 non twin cards might not have this register
(and if they do, it doesn't reflect the LVD/SE bus setting).

This is a pretty significant alteration, so it's not a -rc candidate,
but I'll put it in scsi-misc and see how it works out.

James

Re: Linux 2.6.18-rc6

[Doug Ledford]

[-- Attachment #1: Type: text/plain, Size: 1701 bytes --]

On Sun, 2006-09-17 at 09:05 -0500, James Bottomley wrote:
> On Sun, 2006-09-17 at 07:38 +0200, Olaf Hering wrote:
> > As pointed out in private mail, this patch fixes the machine check for
> > me. Thanks Doug.
> > 
> > Maybe the AHC_ULTRA2 feature check is needed as well for other cards.
> 
> It is ... the non ULTRA2 non twin cards might not have this register
> (and if they do, it doesn't reflect the LVD/SE bus setting).
> 
> This is a pretty significant alteration, so it's not a -rc candidate,
> but I'll put it in scsi-misc and see how it works out.

No, it's present on all cards.  Reading it for signaling may not be
needed on non-ultra 2 cards (as far as LVD goes), but it won't hurt.
However, all the other places this particular register is touched in the
driver, the card is already paused.  Olaf's problem may be that this is
one of the registers that require the sequencer be paused before you
touch it.  Depending on the chipset, if you touch a pause only register,
it either pukes up like Olaf is seeing or auto pauses the chip.  I had
thought that all the Ultra2 chipsets did autopause, but maybe the
current driver disables that (and even if it did autopause, you would
still need an unpause or else the card stops until the next time
something happens that includes a pause/unpause pair).  Anyway, I asked
Olaf to try wrapping the read in an ahc_lock/unlock and pause/unpause
pair to see if it makes a difference.  We'll see.

-- 
Doug Ledford <dledford@redhat.com>
              GPG KeyID: CFBFF194
              http://people.redhat.com/dledford

Infiniband specific RPMs available at
              http://people.redhat.com/dledford/Infiniband

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]

Re: Linux 2.6.18-rc6

[Doug Ledford]

[-- Attachment #1: Type: text/plain, Size: 2628 bytes --]

On Sun, 2006-09-17 at 07:38 +0200, Olaf Hering wrote:
> On Fri, Sep 15, Doug Ledford wrote:
> 
> > On Thu, 2006-09-07 at 09:04 -0500, James Bottomley wrote:
> > > On Thu, 2006-09-07 at 11:15 +0200, Olaf Hering wrote:
> > > > This does not work: ahc_linux_get_signalling: f 56f6
> > > > 
> > > > echo $(( 0x56f6 & 0x00002 )) gives 2, and the ahc_inb is called.
> > > 
> > > Erm, there's something else going on then:  An ultra 2 card has to have
> > > this register.  It's used to signal mode changes in
> > > ahc_handle_scsiint().  The piece of code in there will trigger and read
> > > this register for any ultra 2 + controller every time there's an error
> > > (just to see if the bus mode changed).
> > 
> > Sorry for my belated response, but this usually happens when you access
> > an aic chipset too soon after a chip reset.  Try putting a delay before
> > whatever access is causing this to see if it make s difference.  Common
> > problems include after a chip reset, touching any register will cause
> > the card to reset, etc.
> 
> As pointed out in private mail, this patch fixes the machine check for
> me. Thanks Doug.

Hehehe, everyone ignore my last email, I hadn't seen this one ;-)
You're welcome.

> Maybe the AHC_ULTRA2 feature check is needed as well for other cards.
> 
> ---
>  drivers/scsi/aic7xxx/aic7xxx_osm.c |    9 ++++++++-
>  1 file changed, 8 insertions(+), 1 deletion(-)
> 
> Index: linux-2.6.18-rc7/drivers/scsi/aic7xxx/aic7xxx_osm.c
> ===================================================================
> --- linux-2.6.18-rc7.orig/drivers/scsi/aic7xxx/aic7xxx_osm.c
> +++ linux-2.6.18-rc7/drivers/scsi/aic7xxx/aic7xxx_osm.c
> @@ -2539,7 +2539,14 @@ static void ahc_linux_set_iu(struct scsi
>  static void ahc_linux_get_signalling(struct Scsi_Host *shost)
>  {
>  	struct ahc_softc *ahc = *(struct ahc_softc **)shost->hostdata;
> -	u8 mode = ahc_inb(ahc, SBLKCTL);
> +	unsigned long flags;
> +	u8 mode;
> +
> +	ahc_lock(ahc, &flags);
> +	ahc_pause(ahc);
> +	mode = ahc_inb(ahc, SBLKCTL);
> +	ahc_unpause(ahc);
> +	ahc_unlock(ahc, &flags);
>  
>  	if (mode & ENAB40)
>  		spi_signalling(shost) = SPI_SIGNAL_LVD;
> -
> To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
-- 
Doug Ledford <dledford@redhat.com>
              GPG KeyID: CFBFF194
              http://people.redhat.com/dledford

Infiniband specific RPMs available at
              http://people.redhat.com/dledford/Infiniband

[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]