From: Michael Stone <mstone@mathom.us>
To: linux-scsi@vger.kernel.org
Subject: aic79xx dumping card state
Date: Thu, 09 Nov 2006 19:45:09 -0500 [thread overview]
Message-ID: <20061110004508.GF2667@mathom.us> (raw)
How to debug? Kernel is 2.6.18.1, I think the other details are in the
dmesg output:
ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 16 (level, low) -> IRQ 21
scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 39320A Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
Vendor: SC U320/ Model: SATA16R Rev: R0.0
Type: Direct-Access ANSI SCSI revision: 03
target2:0:0: asynchronous
scsi2:A:0:0: Tagged Queuing enabled. Depth 32
target2:0:0: Beginning Domain Validation
target2:0:0: wide asynchronous
target2:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 127)
target2:0:0: Ending Domain Validation
SCSI device sdb: 4095967232 1024-byte hdwr sectors (4194270 MB)
sdb: Write Protect is off
sdb: Mode Sense: cd 00 00 08
SCSI device sdb: drive cache: write back
SCSI device sdb: 4095967232 1024-byte hdwr sectors (4194270 MB)
sdb: Write Protect is off
sdb: Mode Sense: cd 00 00 08
SCSI device sdb: drive cache: write back
sdb: unknown partition table
sd 2:0:0:0: Attached scsi disk sdb
At this point I try to dd from /dev/sdb, don't get very far before:
sd 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x28 0x0 0x0 0x0 0x28 0x70
0x0 0x1 0x0 0x0
scsi2: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi2: Dumping Card State at program address 0x3b Mode 0x22
Card was paused
INTSTAT[0x0] SELOID[0x0] SELID[0x0] HS_MAILBOX[0x0]
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
SCSISIGI[0x24]:(P_DATAOUT_DT|BSYI) SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE)
SCSISEQ0[0x40]:(ENSELO) SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI)
SEQCTL0[0x0] SEQINTCTL[0x0] SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]:(SELECTOUT_QFROZEN)
QFREEZE_COUNT[0x0] KERNEL_QFREEZE_COUNT[0x0] MK_MESSAGE_SCB[0xff00]
MK_MESSAGE_SCSIID[0xff] SSTAT0[0x10]:(SELINGO)
SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x80]:(PACKETIZED)
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x40]
SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff CURRSCB 0x3 NEXTSCB 0xff00
qinstart = 90 qinfifonext = 90
QINFIFO:
WAITING_TID_QUEUES:
0 ( 0x3 )
Pending list:
3 FIFO_USE[0x0] SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7]
Total 1
Kernel Free SCB list: 2 1 0
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
Sequencer On QFreeze and Complete list:
scsi2: FIFO0 Free, LONGJMP == 0x8271, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEP
TRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
scsi2: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEP
TRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
LQIN: 0x8 0x0 0x0 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x
0 0x0
scsi2: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
scsi2: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi2: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
SIMODE0[0xc]:(ENOVERRUN|ENIOERR)
CCSCBCTL[0x4]:(CCSCBDIR)
scsi2: REG0 == 0x3, SINDEX = 0x102, DINDEX = 0x102
scsi2: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
CDB 3 1 0 0 0 0
STACK: 0x24 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi2:0:0:0: Cmd aborted from QINFIFO
sd 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0
0x0 0x0
scsi2: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi2: Dumping Card State at program address 0x3b Mode 0x22
Card was paused
INTSTAT[0x0] SELOID[0x0] SELID[0x0] HS_MAILBOX[0x0]
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
SCSISIGI[0x24]:(P_DATAOUT_DT|BSYI) SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE)
SCSISEQ0[0x40]:(ENSELO) SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI)
SEQCTL0[0x0] SEQINTCTL[0x0] SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]:(SELECTOUT_QFROZEN)
QFREEZE_COUNT[0x0] KERNEL_QFREEZE_COUNT[0x0] MK_MESSAGE_SCB[0xff00]
MK_MESSAGE_SCSIID[0xff] SSTAT0[0x10]:(SELINGO)
SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x80]:(PACKETIZED)
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x40]
SCB Count = 4 CMDS_PENDING = 0 LASTSCB 0xffff CURRSCB 0x3 NEXTSCB 0xff00
qinstart = 90 qinfifonext = 91
QINFIFO: 0x3
WAITING_TID_QUEUES:
Pending list:
3 FIFO_USE[0x0] SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7]
Total 1
Kernel Free SCB list: 2 1 0
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
Sequencer On QFreeze and Complete list:
scsi2: FIFO0 Free, LONGJMP == 0x8271, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEP
TRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
scsi2: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEP
TRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
LQIN: 0x8 0x0 0x0 0x3 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x
0 0x0
scsi2: LQISTATE = 0x1, LQOSTATE = 0x1a, OPTIONMODE = 0x52
scsi2: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi2: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
SIMODE0[0xc]:(ENOVERRUN|ENIOERR)
CCSCBCTL[0x4]:(CCSCBDIR)
scsi2: REG0 == 0x3, SINDEX = 0x102, DINDEX = 0x102
scsi2: SCBPTR == 0xff03, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
CDB 3 1 0 0 0 0
STACK: 0x24 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi2:0:0:0: Cmd aborted from QINFIFO
sd 2:0:0:0: Attempting to queue a TARGET RESET message:CDB: 0x28 0x0 0x0
0x0 0x2
8 0x70 0x0 0x1 0x0 0x0
scsi2: Device reset code sleeping
scsi2: Device reset timer expired (active 1)
scsi2: Device reset returning 0x2003
Recovery SCB completes
sd 2:0:0:0: scsi: Device offlined - not ready after error recovery
sd 2:0:0:0: SCSI error: return code = 0x00020000
end_request: I/O error, dev sdb, sector 20704
Buffer I/O error on device sdb, logical block 2588
Buffer I/O error on device sdb, logical block 2589
Buffer I/O error on device sdb, logical block 2590
Buffer I/O error on device sdb, logical block 2591
Buffer I/O error on device sdb, logical block 2592
Buffer I/O error on device sdb, logical block 2593
Buffer I/O error on device sdb, logical block 2594
sd 2:0:0:0: rejecting I/O to offline device
Buffer I/O error on device sdb, logical block 2588
Buffer I/O error on device sdb, logical block 2595
Buffer I/O error on device sdb, logical block 2596
next reply other threads:[~2006-11-10 0:45 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-10 0:45 Michael Stone [this message]
2006-11-10 15:01 ` aic79xx dumping card state Jaco van der Schyff
2006-11-10 15:39 ` Michael Stone
2006-11-10 17:09 ` Jaco van der Schyff
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061110004508.GF2667@mathom.us \
--to=mstone@mathom.us \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox