* Re: adaptec 3405 + 4 sas disks: synchronize_callback: synchronize failed, status = 226
2008-07-14 11:19 ` Mark Salyzyn
@ 2008-07-14 11:45 ` Arkadiusz Miskiewicz
0 siblings, 0 replies; 3+ messages in thread
From: Arkadiusz Miskiewicz @ 2008-07-14 11:45 UTC (permalink / raw)
To: Mark Salyzyn; +Cc: Linux-Scsi, AACRAID, Achim Leubner
On Monday 14 July 2008, Mark Salyzyn wrote:
> 226 means CT_ERROR, a generic response to the CT_FLUSH_CACHE command
> to the controller when the action could not be performed.
>
> The action is to flush all the controller's cache to the targets in
> response to a SCSI SYNCHRONIZE_CACHE command. I expect that you are
> running with a degraded array, or incompatible drives?
It's in "Optimal" state and I have no idea which drives are "incompatible".
Is this list published somewhere (I was looking at 3405 download section at
adaptec.com)?
# ./arcconf64 getconfig 1 al
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 3405
Controller Serial Number : 8C0210064E7
Temperature : 46 C/ 114 F (Normal)
Installed memory : 128 MB
Copyback : Disabled
Background consistency check : Disabled
Automatic Failover : Enabled
Global task priority : High
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/0
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (15728)
Firmware : 5.2-0 (15728)
Driver : 1.1-5 (2449)
Boot Flash : 5.2-0 (15728)
--------------------------------------------------------
Controller Battery Information
--------------------------------------------------------
Status : Optimal
Over temperature : No
Capacity remaining : 99 percent
Time remaining (at current draw) : 3 days, 1 hours, 11 minutes
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : RAID
RAID level : 10
Status of logical device : Optimal
Size : 571392 MB
Stripe-unit size : 256 KB
Read-cache mode : Enabled
Write-cache mode : Enabled (write-back)
Write-cache setting : Enabled (write-back) when
protected by battery
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (0,0)
3LM4DRD200009842S4XD
Group 0, Segment 1 : Present (0,1)
3LM4DRDZ00009842RNGC
Group 1, Segment 0 : Present (0,2)
3LM4DS0P00009808RMV7
Group 1, Segment 1 : Present (0,3)
3LM48ABH00009842SXEE
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,0
Reported Location : Enclosure 0, Slot 0
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DRD200009842S4XD
World-wide name : 5000C5000A4B3558
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #1
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,1
Reported Location : Enclosure 0, Slot 1
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DRDZ00009842RNGC
World-wide name : 5000C5000A4B3800
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #2
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,2
Reported Location : Enclosure 0, Slot 2
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DS0P00009808RMV7
World-wide name : 5000C5000A4B3074
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #3
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,3
Reported Location : Enclosure 0, Slot 3
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM48ABH00009842SXEE
World-wide name : 5000C5000A4B39B4
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #4
Device is an Enclosure services device
Reported Channel,Device : 2,0
Enclosure ID : 0
Type : SES2
Vendor : ADAPTEC
Model : Virtual SGPIO 0
Firmware : 0001
Status of Enclosure services device
Temperature : Normal
Command completed successfully.
>
> Make sure your drive and controller firmware is as up-to-date as
> possible.
Controller firmware is up to date. Disks firmware is 002 according to
arcconf, unfortunately seagate doesn't seem to publish firmware on their
site, so I don't know if it's old or new.
>
> Sincerely -- Mark Salyzyn
>
> On Jul 14, 2008, at 2:09 AM, Arkadiusz Miskiewicz wrote:
> > Hello,
> >
> > I'm running 2.6.24.3 kernel and I'm getting few error messages
> > comming from
> > aacraid driver. Hardware is adaptec 3405 running firmware 15728 + 4
> > SAS 300GB
> > harddisks configured in single raid10 array.
> >
> > [167674.161866] synchronize_callback: synchronize failed, status = 226
> > [168977.738031] synchronize_callback: synchronize failed, status = 226
> > [172180.752140] synchronize_callback: synchronize failed, status = 226
> > [177494.855145] synchronize_callback: synchronize failed, status = 226
> > [189594.477223] synchronize_callback: synchronize failed, status = 226
> > [191411.881236] synchronize_callback: synchronize failed, status = 226
> > [217130.596663] synchronize_callback: synchronize failed, status = 226
> > [219236.032362] synchronize_callback: synchronize failed, status = 226
> >
> > What does 226 mean and what does it indicate (serious problem?) ?
> >
> > ps. would be good if prefix was added to these messages to know
> > where these
> > come from
> > --
> > Arkadiusz Miśkiewicz PLD/Linux Team
> > arekm / maven.pl http://ftp.pld-linux.org/
--
Arkadiusz Miśkiewicz PLD/Linux Team
arekm / maven.pl http://ftp.pld-linux.org/
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 3+ messages in thread