From: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
To: linux-scsi@vger.kernel.org
Cc: James.Bottomley@HansenPartnership.com, dab@hp.com,
mikem@beardog.cce.hp.com
Subject: [PATCH 07/24] hpsa: factor out hpsa_find_cfgtables
Date: Thu, 27 May 2010 15:13:17 -0500 [thread overview]
Message-ID: <20100527201317.3116.58539.stgit@beardog.cce.hp.com> (raw)
In-Reply-To: <20100527200301.3116.78973.stgit@beardog.cce.hp.com>
From: Stephen M. Cameron <scameron@beardog.cce.hp.com>
hpsa: factor out hpsa_find_cfgtables
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
---
drivers/scsi/hpsa.c | 50 ++++++++++++++++++++++++++++++--------------------
1 files changed, 30 insertions(+), 20 deletions(-)
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 12b1625..3ed0fd7 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -3325,12 +3325,39 @@ static int __devinit hpsa_wait_for_board_ready(struct ctlr_info *h)
return -ENODEV;
}
-static int __devinit hpsa_pci_init(struct ctlr_info *h)
+static int __devinit hpsa_find_cfgtables(struct ctlr_info *h)
{
u64 cfg_offset;
u32 cfg_base_addr;
u64 cfg_base_addr_index;
u32 trans_offset;
+
+ /* get the address index number */
+ cfg_base_addr = readl(h->vaddr + SA5_CTCFG_OFFSET);
+ cfg_base_addr &= (u32) 0x0000ffff;
+ cfg_base_addr_index = find_PCI_BAR_index(h->pdev, cfg_base_addr);
+ if (cfg_base_addr_index == -1) {
+ dev_warn(&h->pdev->dev, "cannot find cfg_base_addr_index\n");
+ return -ENODEV;
+ }
+ cfg_offset = readl(h->vaddr + SA5_CTMEM_OFFSET);
+ h->cfgtable = remap_pci_mem(pci_resource_start(h->pdev,
+ cfg_base_addr_index) + cfg_offset,
+ sizeof(h->cfgtable));
+ if (!h->cfgtable)
+ return -ENOMEM;
+ /* Find performant mode table. */
+ trans_offset = readl(&(h->cfgtable->TransMethodOffset));
+ h->transtable = remap_pci_mem(pci_resource_start(h->pdev,
+ cfg_base_addr_index)+cfg_offset+trans_offset,
+ sizeof(*h->transtable));
+ if (!h->transtable)
+ return -ENOMEM;
+ return 0;
+}
+
+static int __devinit hpsa_pci_init(struct ctlr_info *h)
+{
int i, prod_index, err;
prod_index = hpsa_lookup_board_id(h->pdev, &h->board_id);
@@ -3364,26 +3391,9 @@ static int __devinit hpsa_pci_init(struct ctlr_info *h)
err = hpsa_wait_for_board_ready(h);
if (err)
goto err_out_free_res;
-
- /* get the address index number */
- cfg_base_addr = readl(h->vaddr + SA5_CTCFG_OFFSET);
- cfg_base_addr &= (u32) 0x0000ffff;
- cfg_base_addr_index = find_PCI_BAR_index(h->pdev, cfg_base_addr);
- if (cfg_base_addr_index == -1) {
- dev_warn(&h->pdev->dev, "cannot find cfg_base_addr_index\n");
- err = -ENODEV;
+ err = hpsa_find_cfgtables(h);
+ if (err)
goto err_out_free_res;
- }
-
- cfg_offset = readl(h->vaddr + SA5_CTMEM_OFFSET);
- h->cfgtable = remap_pci_mem(pci_resource_start(h->pdev,
- cfg_base_addr_index) + cfg_offset,
- sizeof(h->cfgtable));
- /* Find performant mode table. */
- trans_offset = readl(&(h->cfgtable->TransMethodOffset));
- h->transtable = remap_pci_mem(pci_resource_start(h->pdev,
- cfg_base_addr_index)+cfg_offset+trans_offset,
- sizeof(*h->transtable));
h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands));
h->maxsgentries = readl(&(h->cfgtable->MaxScatterGatherElements));
next prev parent reply other threads:[~2010-05-27 20:08 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-05-27 20:12 [PATCH 00/24] hpsa updates for May 2010 Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 01/24] hpsa: save pdev pointer in per hba structure early to avoid passing it around so much Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 02/24] hpsa: factor out hpsa_lookup_board_id Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 03/24] hpsa: factor out hpsa_board_disabled Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 04/24] hpsa: remove redundant board_id parameter from hpsa_interrupt_mode Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 05/24] hpsa: factor out hpsa_find_memory_BAR Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 06/24] hpsa: factor out hpsa_wait_for_board_ready Stephen M. Cameron
2010-05-27 20:13 ` Stephen M. Cameron [this message]
2010-05-27 20:13 ` [PATCH 08/24] hpsa: fix leak of ioremapped memory Stephen M. Cameron
2010-05-28 19:12 ` Rolf Eike Beer
2010-06-01 12:55 ` scameron
2010-05-27 20:13 ` [PATCH 09/24] hpsa: hpsa factor out hpsa_find_board_params Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 10/24] hpsa: factor out hpsa-CISS-signature-present Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 11/24] hpsa: factor out hpsa_enable_scsi_prefetch Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 12/24] hpsa: factor out hpsa_p600_dma_prefetch_quirk Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 13/24] hpsa: factor out hpsa_enter_simple_mode Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 14/24] hpsa: check that simple mode is supported Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 15/24] hpsa: clean up debug ifdefs Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 16/24] hpsa: mark hpsa_mark_hpsa_put_ctlr_into_performant_mode as __devinit Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 17/24] hpsa: factor out hpsa_wait_for_mode_change_ack Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 18/24] hpsa: remove unused variable trans_offset Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 19/24] hpsa: factor out hpsa_enter_performant_mode Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 20/24] hpsa: remove unused firm_ver member of the per-hba structure Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 21/24] hpsa: Add hpsa.txt to Documentation/scsi Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 22/24] hpsa: expose controller firmware revision via /sys Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 23/24] hpsa: fix block fetch table problem Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 24/24] hpsa: add entry to MAINTAINERS Stephen M. Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100527201317.3116.58539.stgit@beardog.cce.hp.com \
--to=scameron@beardog.cce.hp.com \
--cc=James.Bottomley@HansenPartnership.com \
--cc=dab@hp.com \
--cc=linux-scsi@vger.kernel.org \
--cc=mikem@beardog.cce.hp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).