From: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
To: linux-scsi@vger.kernel.org
Cc: James.Bottomley@HansenPartnership.com, dab@hp.com,
mikem@beardog.cce.hp.com
Subject: [PATCH 09/24] hpsa: hpsa factor out hpsa_find_board_params
Date: Thu, 27 May 2010 15:13:27 -0500 [thread overview]
Message-ID: <20100527201327.3116.43162.stgit@beardog.cce.hp.com> (raw)
In-Reply-To: <20100527200301.3116.78973.stgit@beardog.cce.hp.com>
From: Stephen M. Cameron <scameron@beardog.cce.hp.com>
hpsa: hpsa factor out hpsa_find_board_params
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
---
drivers/scsi/hpsa.c | 46 +++++++++++++++++++++++++---------------------
1 files changed, 25 insertions(+), 21 deletions(-)
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 3745047..b69eaad 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -3356,6 +3356,30 @@ static int __devinit hpsa_find_cfgtables(struct ctlr_info *h)
return 0;
}
+/* Interrogate the hardware for some limits:
+ * max commands, max SG elements without chaining, and with chaining,
+ * SG chain block size, etc.
+ */
+static void __devinit hpsa_find_board_params(struct ctlr_info *h)
+{
+ h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands));
+ h->nr_cmds = h->max_commands - 4; /* Allow room for some ioctls */
+ h->maxsgentries = readl(&(h->cfgtable->MaxScatterGatherElements));
+ /*
+ * Limit in-command s/g elements to 32 save dma'able memory.
+ * Howvever spec says if 0, use 31
+ */
+ h->max_cmd_sg_entries = 31;
+ if (h->maxsgentries > 512) {
+ h->max_cmd_sg_entries = 32;
+ h->chainsize = h->maxsgentries - h->max_cmd_sg_entries + 1;
+ h->maxsgentries--; /* save one for chain pointer */
+ } else {
+ h->maxsgentries = 31; /* default to traditional values */
+ h->chainsize = 0;
+ }
+}
+
static int __devinit hpsa_pci_init(struct ctlr_info *h)
{
int i, prod_index, err;
@@ -3397,27 +3421,7 @@ static int __devinit hpsa_pci_init(struct ctlr_info *h)
err = hpsa_find_cfgtables(h);
if (err)
goto err_out_free_res;
-
- h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands));
- h->maxsgentries = readl(&(h->cfgtable->MaxScatterGatherElements));
-
- /*
- * Limit in-command s/g elements to 32 save dma'able memory.
- * Howvever spec says if 0, use 31
- */
-
- h->max_cmd_sg_entries = 31;
- if (h->maxsgentries > 512) {
- h->max_cmd_sg_entries = 32;
- h->chainsize = h->maxsgentries - h->max_cmd_sg_entries + 1;
- h->maxsgentries--; /* save one for chain pointer */
- } else {
- h->maxsgentries = 31; /* default to traditional values */
- h->chainsize = 0;
- }
-
- /* Allow room for some ioctls */
- h->nr_cmds = h->max_commands - 4;
+ hpsa_find_board_params(h);
if ((readb(&h->cfgtable->Signature[0]) != 'C') ||
(readb(&h->cfgtable->Signature[1]) != 'I') ||
next prev parent reply other threads:[~2010-05-27 20:08 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-05-27 20:12 [PATCH 00/24] hpsa updates for May 2010 Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 01/24] hpsa: save pdev pointer in per hba structure early to avoid passing it around so much Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 02/24] hpsa: factor out hpsa_lookup_board_id Stephen M. Cameron
2010-05-27 20:12 ` [PATCH 03/24] hpsa: factor out hpsa_board_disabled Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 04/24] hpsa: remove redundant board_id parameter from hpsa_interrupt_mode Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 05/24] hpsa: factor out hpsa_find_memory_BAR Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 06/24] hpsa: factor out hpsa_wait_for_board_ready Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 07/24] hpsa: factor out hpsa_find_cfgtables Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 08/24] hpsa: fix leak of ioremapped memory Stephen M. Cameron
2010-05-28 19:12 ` Rolf Eike Beer
2010-06-01 12:55 ` scameron
2010-05-27 20:13 ` Stephen M. Cameron [this message]
2010-05-27 20:13 ` [PATCH 10/24] hpsa: factor out hpsa-CISS-signature-present Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 11/24] hpsa: factor out hpsa_enable_scsi_prefetch Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 12/24] hpsa: factor out hpsa_p600_dma_prefetch_quirk Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 13/24] hpsa: factor out hpsa_enter_simple_mode Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 14/24] hpsa: check that simple mode is supported Stephen M. Cameron
2010-05-27 20:13 ` [PATCH 15/24] hpsa: clean up debug ifdefs Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 16/24] hpsa: mark hpsa_mark_hpsa_put_ctlr_into_performant_mode as __devinit Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 17/24] hpsa: factor out hpsa_wait_for_mode_change_ack Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 18/24] hpsa: remove unused variable trans_offset Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 19/24] hpsa: factor out hpsa_enter_performant_mode Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 20/24] hpsa: remove unused firm_ver member of the per-hba structure Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 21/24] hpsa: Add hpsa.txt to Documentation/scsi Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 22/24] hpsa: expose controller firmware revision via /sys Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 23/24] hpsa: fix block fetch table problem Stephen M. Cameron
2010-05-27 20:14 ` [PATCH 24/24] hpsa: add entry to MAINTAINERS Stephen M. Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100527201327.3116.43162.stgit@beardog.cce.hp.com \
--to=scameron@beardog.cce.hp.com \
--cc=James.Bottomley@HansenPartnership.com \
--cc=dab@hp.com \
--cc=linux-scsi@vger.kernel.org \
--cc=mikem@beardog.cce.hp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).