Re: mvsas errors in 3.0

public inbox for linux-scsi@vger.kernel.org
 help / color / mirror / Atom feed

* Re: mvsas errors in 3.0
       [not found] <201109162002.13801.thomas@fjellstrom.ca>
@ 2011-09-19  4:18 ` Thomas Fjellstrom
  2011-09-23  1:40   ` mvsas errors in 3.0, URGENT Thomas Fjellstrom
  0 siblings, 1 reply; 2+ messages in thread
From: Thomas Fjellstrom @ 2011-09-19  4:18 UTC (permalink / raw)
  To: Linux Kernel List; +Cc: linux-scsi

On September 16, 2011, Thomas Fjellstrom wrote:
> Hi, its me again.
> 
> Just updated to 3.0 last night, after the card had locked up twice in as many
> days. However, I just heard some unsettling noises come from my raid array,
> like one of the disks was being re-initialized several times. spinning up and
> down a few times, etc.
> 
> When I got to look at the logs, I find this:
> 
> [21051.403115] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 2084:Release slot [0] tag[0], task [ffff88013ed982c0]:
> [21051.403134] sas: sas_ata_task_done: SAS error 8a
> [21051.407099] sas: Enter sas_scsi_recover_host
> [21051.407099] ata14: sas eh calling libata cmd error handler
> [21051.407099] ata9: sas eh calling libata port error handler
> [21051.407099] ata10: sas eh calling libata port error handler
> [21051.407099] ata11: sas eh calling libata port error handler
> [21051.407099] ata12: sas eh calling libata port error handler
> [21051.407099] ata13: sas eh calling libata port error handler
> [21051.407099] ata14: sas eh calling libata port error handler
> [21051.407099] sas: sas_ata_task_done: SAS error 8a
> [21051.407099] ata14: failed to read log page 10h (errno=-5)
> [21051.414118] ata14.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6
> [21051.414118] ata14.00: failed command: READ FPDMA QUEUED
> [21051.417174] ata14.00: cmd 60/10:00:b0:a9:37/00:00:0e:00:00/40 tag 0 ncq 8192 in
> [21051.417180]          res 01/04:00:f8:e4:c6/00:00:47:00:00/40 Emask 0x3 (HSM violation)
> [21051.419797] ata14.00: status: { ERR }
> [21051.421106] ata14.00: error: { ABRT }
> [21051.422427] ata14: hard resetting link
> [21051.422434] sas: sas_ata_hard_reset: Found ATA device.
> [21051.422446] sas: sas_ata_task_done: SAS error 8a
> [21051.422476] sas: sas_ata_task_done: SAS error 8a
> [21051.422484] ata14.00: both IDENTIFYs aborted, assuming NODEV
> [21051.422491] ata14.00: revalidation failed (errno=-2)
> [21053.443487] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21055.460022] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21055.631886] sas: sas_form_port: phy6 belongs to port5 already(1)!
> [21056.420060] ata14: hard resetting link
> [21056.420070] sas: sas_ata_hard_reset: Found ATA device.
> [21056.486683] ata14.00: configured for UDMA/133
> [21056.486708] ata14: EH complete
> [21056.486718] ata15: sas eh calling libata port error handler
> [21056.486735] sas: --- Exit sas_scsi_recover_host
> [21056.665913] sas: sas_ata_task_done: SAS error 8a
> [21056.665947] sas: Enter sas_scsi_recover_host
> [21056.665958] ata14: sas eh calling libata cmd error handler
> [21056.665973] ata9: sas eh calling libata port error handler
> [21056.665996] ata10: sas eh calling libata port error handler
> [21056.666011] ata11: sas eh calling libata port error handler
> [21056.666024] ata12: sas eh calling libata port error handler
> [21056.666035] ata13: sas eh calling libata port error handler
> [21056.666047] ata14: sas eh calling libata port error handler
> [21056.666066] sas: sas_ata_task_done: SAS error 8a
> [21056.666079] ata14: failed to read log page 10h (errno=-5)
> [21056.667428] ata14.00: exception Emask 0x1 SAct 0x1 SErr 0x0 action 0x6
> [21056.668777] ata14.00: failed command: READ FPDMA QUEUED
> [21056.670091] ata14.00: cmd 60/08:00:a8:ed:2e/00:00:10:00:00/40 tag 0 ncq 4096 in
> [21056.670095]          res 01/04:00:20:59:6d/00:00:02:00:00/40 Emask 0x3 (HSM violation)
> [21056.672687] ata14.00: status: { ERR }
> [21056.674070] ata14.00: error: { ABRT }
> [21056.675399] ata14: hard resetting link
> [21056.675405] sas: sas_ata_hard_reset: Found ATA device.
> [21056.675418] sas: sas_ata_task_done: SAS error 8a
> [21056.675480] sas: sas_ata_task_done: SAS error 8a
> [21056.675489] ata14.00: both IDENTIFYs aborted, assuming NODEV
> [21056.675496] ata14.00: revalidation failed (errno=-2)
> [21057.512008] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21058.624012] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21059.564016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21060.676016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21061.616006] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21061.672045] ata14: hard resetting link
> [21061.672055] sas: sas_ata_hard_reset: Found ATA device.
> [21061.672116] sas: sas_ata_task_done: SAS error 2
> [21061.672193] sas: sas_ata_task_done: SAS error 2
> [21061.672208] ata14.00: both IDENTIFYs aborted, assuming NODEV
> [21061.672216] ata14.00: revalidation failed (errno=-2)
> [21062.728006] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21064.324014] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21064.780018] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21066.376015] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21066.672061] ata14: hard resetting link
> [21066.672070] sas: sas_ata_hard_reset: Found ATA device.
> [21066.672124] sas: sas_ata_task_done: SAS error 2
> [21066.672168] sas: sas_ata_task_done: SAS error 2
> [21066.672183] ata14.00: both IDENTIFYs aborted, assuming NODEV
> [21066.672190] ata14.00: revalidation failed (errno=-2)
> [21066.673517] ata14.00: disabled
> [21066.673542] ata14: EH complete
> [21066.673550] ata15: sas eh calling libata port error handler
> [21066.673570] sas: --- Exit sas_scsi_recover_host
> [21066.673690] sd 8:0:5:0: [sdi] Unhandled error code
> [21066.673697] sd 8:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [21066.673707] sd 8:0:5:0: [sdi] CDB: Read(10): 28 00 10 2e ed a8 00 00 08 00
> [21066.673738] end_request: I/O error, dev sdi, sector 271510952
> [21066.679965] sd 8:0:5:0: [sdi] Unhandled error code
> [21066.679971] sd 8:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [21066.679979] sd 8:0:5:0: [sdi] CDB: Write(10): 2a 00 00 00 00 02 00 00 05 00
> [21066.679997] end_request: I/O error, dev sdi, sector 2
> [21066.686083] end_request: I/O error, dev sdi, sector 2
> [21066.690044] md: super_written gets error=-5, uptodate=0
> [21066.690044] md/raid:md1: Disk failure on sdi, disabling device.
> [21066.690044] md/raid:md1: Operation continuing on 6 devices.
> [21066.742358] RAID conf printout:
> [21066.742361]  --- level:5 rd:7 wd:6
> [21066.742363]  disk 0, o:1, dev:sdf
> [21066.742364]  disk 1, o:1, dev:sdg
> [21066.742366]  disk 2, o:1, dev:sdd
> [21066.742367]  disk 3, o:1, dev:sde
> [21066.742369]  disk 4, o:1, dev:sdj
> [21066.742370]  disk 5, o:0, dev:sdi
> [21066.742371]  disk 6, o:1, dev:sdh
> [21066.745218] RAID conf printout:
> [21066.745227]  --- level:5 rd:7 wd:6
> [21066.745234]  disk 0, o:1, dev:sdf
> [21066.745240]  disk 1, o:1, dev:sdg
> [21066.745245]  disk 2, o:1, dev:sdd
> [21066.745249]  disk 3, o:1, dev:sde
> [21066.745264]  disk 4, o:1, dev:sdj
> [21066.745269]  disk 6, o:1, dev:sdh
> [21066.832016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21068.428013] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21068.895664] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21070.480008] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21070.936016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21072.532018] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21072.988016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21074.584017] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21075.040016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21076.636009] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21077.092020] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21077.886806] sas: sas_form_port: phy6 belongs to port5 already(1)!
> [21098.260007] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21100.312016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21100.512833] sas: sas_form_port: phy6 belongs to port5 already(1)!
> [21119.388007] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21121.472339] sd 8:0:5:0: [sdi] Synchronizing SCSI cache
> [21121.472460] sd 8:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [21121.472474] sd 8:0:5:0: [sdi] Stopping disk
> [21121.472512] sd 8:0:5:0: [sdi] START_STOP FAILED
> [21121.472521] sd 8:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [21124.632016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21133.336022] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21135.424511] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21137.440016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [21138.137603] sas: phy-8:6 added to port-8:5, phy_mask:0x40 ( 600000000000000)
> [21138.137636] sas: DOING DISCOVERY on port 5, pid:235
> [21138.140579] sas: Enter sas_scsi_recover_host
> [21138.140584] ata9: sas eh calling libata port error handler
> [21138.140595] ata10: sas eh calling libata port error handler
> [21138.140600] ata11: sas eh calling libata port error handler
> [21138.140605] ata12: sas eh calling libata port error handler
> [21138.140609] ata13: sas eh calling libata port error handler
> [21138.140614] ata15: sas eh calling libata port error handler
> [21138.140619] ata16: sas eh calling libata port error handler
> [21138.140627] sas: sas_ata_hard_reset: Found ATA device.
> [21138.167643] ata16.00: ATA-8: ST31000528AS, CC34, max UDMA/133
> [21138.167649] ata16.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [21138.207197] ata16.00: configured for UDMA/133
> [21138.207217] sas: --- Exit sas_scsi_recover_host
> [21138.207436] scsi 8:0:7:0: Direct-Access     ATA      ST31000528AS     CC34 PQ: 0 ANSI: 5
> [21138.207899] sd 8:0:7:0: Attached scsi generic sg8 type 0
> [21138.208030] sd 8:0:7:0: [sdk] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [21138.208220] sd 8:0:7:0: [sdk] Write Protect is off
> [21138.208229] sd 8:0:7:0: [sdk] Mode Sense: 00 3a 00 00
> [21138.208281] sd 8:0:7:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [21138.208380] sas: DONE DISCOVERY on port 5, pid:235, result:0
> [21138.225975]  sdk: unknown partition table
> [21138.226482] sd 8:0:7:0: [sdk] Attached SCSI disk
> [72609.206763] sd 8:0:7:0: [sdk] Synchronizing SCSI cache
> [72609.206890] sd 8:0:7:0: [sdk]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [72609.206904] sd 8:0:7:0: [sdk] Stopping disk
> [72609.206935] sd 8:0:7:0: [sdk] START_STOP FAILED
> [72609.206941] sd 8:0:7:0: [sdk]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [72612.720016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [72614.772017] mvsas 0000:04:00.0: Phy6 : No sig fis
> [72616.824016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [72618.876020] mvsas 0000:04:00.0: Phy6 : No sig fis
> [72620.064059] sas: phy-8:6 added to port-8:5, phy_mask:0x40 ( 600000000000000)
> [72620.064569] sas: DOING DISCOVERY on port 5, pid:227
> [72620.067073] sas: Enter sas_scsi_recover_host
> [72620.067083] ata9: sas eh calling libata port error handler
> [72620.067105] ata10: sas eh calling libata port error handler
> [72620.067120] ata11: sas eh calling libata port error handler
> [72620.067133] ata12: sas eh calling libata port error handler
> [72620.067144] ata13: sas eh calling libata port error handler
> [72620.067157] ata15: sas eh calling libata port error handler
> [72620.067168] ata17: sas eh calling libata port error handler
> [72620.067180] sas: sas_ata_hard_reset: Found ATA device.
> [72620.094238] ata17.00: ATA-8: ST31000528AS, CC34, max UDMA/133
> [72620.094249] ata17.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [72620.133748] ata17.00: configured for UDMA/133
> [72620.133770] sas: --- Exit sas_scsi_recover_host
> [72620.133922] scsi 8:0:8:0: Direct-Access     ATA      ST31000528AS     CC34 PQ: 0 ANSI: 5
> [72620.134411] sd 8:0:8:0: [sdk] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
> [72620.134423] sd 8:0:8:0: Attached scsi generic sg8 type 0
> [72620.134596] sas: DONE DISCOVERY on port 5, pid:227, result:0
> [72620.134655] sd 8:0:8:0: [sdk] Write Protect is off
> [72620.134664] sd 8:0:8:0: [sdk] Mode Sense: 00 3a 00 00
> [72620.134754] sd 8:0:8:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [72620.152891]  sdk: unknown partition table
> [72620.153465] sd 8:0:8:0: [sdk] Attached SCSI disk
> [76711.440019] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76713.492006] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76715.544016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76717.599362] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76719.648015] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76721.700012] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76722.598654] sas: sas_form_port: phy6 belongs to port5 already(1)!
> [76725.900016] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76727.952017] mvsas 0000:04:00.0: Phy6 : No sig fis
> [76728.103256] sas: sas_form_port: phy6 belongs to port5 already(1)!
> 
> So, it seems to have at least recovered this time, rather than locking up,
> unfortunately now my raid5 array is rebuilding. Thankfully it seems to have
> been able to use the mdraid bitmap feature, as it only took 20 minutes.
> 

So now 20+ hours after that, I get another error, and the card has locked up,
but this time without trying to reinitialize anything.

[257834.976018] sas: command 0xffff880223a45480, task 0xffff880104a07940, timed out: BLK_EH_NOT_HANDLED
[258000.920151] INFO: task nfsd:12690 blocked for more than 120 seconds.
[258000.921453] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.922715] nfsd            D ffff880223cb5120     0 12690      2 0x00000000
[258000.922727]  ffff880223cb5120 0000000000000046 0000000000000282 0000000000000900
[258000.922740]  ffff880224ee1650 0000000000012800 ffff88010bccbfd8 ffff88010bccbfd8
[258000.922750]  0000000000012800 ffff880223cb5120 0000000000012800 0000000000012800
[258000.922760] Call Trace:
[258000.922777]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.922789]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.922801]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.922811]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.922821]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.922831]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.922841]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.922850]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.922861]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.922872]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.922900]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.922910]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.922922]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.922931]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.922940]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.922949]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.923005]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.923016]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.923036]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.923056]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.923076]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.923101]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.923120]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.923146]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.923165]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.923181]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.923189]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.923199]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.923209]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.923217]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.923224] INFO: task nfsd:12691 blocked for more than 120 seconds.
[258000.924573] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.925920] nfsd            D ffff880185575610     0 12691      2 0x00000000
[258000.925931]  ffff880185575610 0000000000000046 0000000000000246 0000000000000001
[258000.925942]  ffff880185574f20 0000000000012800 ffff880185e83fd8 ffff880185e83fd8
[258000.925952]  0000000000012800 ffff880185575610 0000000000012800 0000000000012800
[258000.925961] Call Trace:
[258000.925972]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.925981]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.925990]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.925999]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.926008]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.926017]  [<ffffffff810b5137>] ? page_waitqueue+0x3/0x6d
[258000.926026]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.926035]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.926044]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.926065]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.926074]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.926085]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.926094]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.926102]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.926111]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.926158]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.926168]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.926187]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.926205]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.926225]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.926249]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.926267]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.926290]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.926309]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.926325]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.926332]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.926341]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.926350]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.926358]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.926364] INFO: task nfsd:12692 blocked for more than 120 seconds.
[258000.927690] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.929054] nfsd            D ffff880185574f20     0 12692      2 0x00000000
[258000.929064]  ffff880185574f20 0000000000000046 ffff88010291b140 ffffffff812b9ec3
[258000.929075]  ffff880226db8f60 0000000000012800 ffff8801f930ffd8 ffff8801f930ffd8
[258000.929085]  0000000000012800 ffff880185574f20 0000000000012800 0000000000012800
[258000.929095] Call Trace:
[258000.929104]  [<ffffffff812b9ec3>] ? tcp_established_options+0x2d/0xa4
[258000.929114]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.929122]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.929132]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.929141]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.929150]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.929159]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.929169]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.929178]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.929187]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.929197]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.929217]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.929228]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.929240]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.929249]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.929257]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.929266]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.929313]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.929323]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.929342]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.929361]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.929380]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.929404]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.929423]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.929446]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.929464]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.929482]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.929490]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.929498]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.929508]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.929516]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.929522] INFO: task nfsd:12693 blocked for more than 120 seconds.
[258000.930827] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.932153] nfsd            D ffff880185574830     0 12693      2 0x00000000
[258000.932163]  ffff880185574830 0000000000000046 ffffffff81008032 ffffffff81008626
[258000.932173]  ffff880226db8f60 0000000000012800 ffff88010c937fd8 ffff88010c937fd8
[258000.932183]  0000000000012800 ffff880185574830 0000000000012800 0000000000012800
[258000.932192] Call Trace:
[258000.932200]  [<ffffffff81008032>] ? load_TLS+0x7/0xa
[258000.932208]  [<ffffffff81008626>] ? __switch_to+0xc9/0x1fb
[258000.932218]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.932226]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.932235]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.932244]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.932253]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.932262]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.932272]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.932280]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.932289]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.932299]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.932319]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.932328]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.932340]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.932349]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.932357]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.932366]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.932412]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.932423]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.932441]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.932460]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.932479]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.932487]  [<ffffffff8133cbae>] ? reschedule_interrupt+0xe/0x20
[258000.932511]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.932530]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.932553]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.932571]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.932589]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.932596]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.932605]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.932614]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.932621]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.932628] INFO: task nfsd:12694 blocked for more than 120 seconds.
[258000.933933] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.935218] nfsd            D ffff880185574140     0 12694      2 0x00000000
[258000.935227]  ffff880185574140 0000000000000046 0000000000000000 ffff880223ecc000
[258000.935237]  ffff880226db8f60 0000000000012800 ffff8801965ddfd8 ffff8801965ddfd8
[258000.935247]  0000000000012800 ffff880185574140 0000000000012800 0000000000012800
[258000.935256] Call Trace:
[258000.935266]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.935274]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.935283]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.935292]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.935301]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.935310]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.935320]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.935328]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.935338]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.935348]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.935367]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.935377]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.935389]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.935398]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.935406]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.935415]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.935461]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.935471]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.935490]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.935508]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.935527]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.935551]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.935570]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.935592]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.935611]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.935628]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.935636]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.935645]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.935654]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.935661]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.935668] INFO: task nfsd:12695 blocked for more than 120 seconds.
[258000.936997] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.938388] nfsd            D ffff880224ee1650     0 12695      2 0x00000000
[258000.938397]  ffff880224ee1650 0000000000000046 ffff880159118540 ffffffffa04b680b
[258000.938408]  ffff880185574830 0000000000012800 ffff880215ff1fd8 ffff880215ff1fd8
[258000.938418]  0000000000012800 ffff880224ee1650 0000000000012800 0000000000012800
[258000.938427] Call Trace:
[258000.938443]  [<ffffffffa04b680b>] ? br_dev_queue_push_xmit+0x72/0x76 [bridge]
[258000.938454]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.938462]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.938472]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.938480]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.938489]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.938498]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.938508]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.938516]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.938526]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.938535]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.938546]  [<ffffffff810bb63c>] ? __free_one_page+0x214/0x295
[258000.938555]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.938566]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.938575]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.938583]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.938592]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.938638]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.938648]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.938667]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.938686]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.938705]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.938729]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.938747]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.938770]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.938788]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.938806]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.938813]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.938822]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.938831]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.938838]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.938845] INFO: task nfsd:12697 blocked for more than 120 seconds.
[258000.940156] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.941464] nfsd            D ffff880224ee0870     0 12697      2 0x00000000
[258000.941473]  ffff880224ee0870 0000000000000046 0000000000000282 0000000000000600
[258000.941483]  ffff880226d460c0 0000000000012800 ffff88014107ffd8 ffff88014107ffd8
[258000.941493]  0000000000012800 ffff880224ee0870 0000000000012800 0000000000012800
[258000.941503] Call Trace:
[258000.941512]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258000.941521]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258000.941530]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258000.941539]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258000.941548]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258000.941557]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258000.941566]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258000.941575]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258000.941584]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258000.941594]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.941613]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258000.941623]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258000.941635]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258000.941644]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258000.941652]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258000.941661]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258000.941707]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258000.941717]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258000.941736]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258000.941754]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258000.941773]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258000.941797]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258000.941816]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258000.941838]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258000.941857]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258000.941874]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258000.941882]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.941890]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.941899]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.941907]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258000.941920] INFO: task kworker/2:3:19027 blocked for more than 120 seconds.
[258000.943279] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258000.944625] kworker/2:3     D ffff8801ad9f4100     0 19027      2 0x00000000
[258000.944636]  ffff8801ad9f4100 0000000000000046 ffff88017ac3e580 00000000d7744850
[258000.944646]  ffff8801a608cf20 0000000000012800 ffff88009cbe7fd8 ffff88009cbe7fd8
[258000.944656]  0000000000012800 ffff8801ad9f4100 0000000000012800 0000000000012800
[258000.944666] Call Trace:
[258000.944677]  [<ffffffff81071f28>] ? arch_local_irq_save+0x14/0x1d
[258000.944724]  [<ffffffffa050f1c1>] ? xlog_wait+0x4f/0x65 [xfs]
[258000.944733]  [<ffffffff8103f0a4>] ? try_to_wake_up+0x199/0x199
[258000.944781]  [<ffffffffa0511b47>] ? _xfs_log_force_lsn+0x1cf/0x205 [xfs]
[258000.944830]  [<ffffffffa051bde9>] ? _xfs_trans_commit+0x110/0x20d [xfs]
[258000.944878]  [<ffffffffa052c530>] ? trace_xfs_irele+0x3b/0x3b [xfs]
[258000.944925]  [<ffffffffa052c530>] ? trace_xfs_irele+0x3b/0x3b [xfs]
[258000.944972]  [<ffffffffa052c56d>] ? xfs_sync_worker+0x3d/0x70 [xfs]
[258000.944982]  [<ffffffff8105b943>] ? process_one_work+0x193/0x28f
[258000.944992]  [<ffffffff8105cacf>] ? worker_thread+0xef/0x172
[258000.945001]  [<ffffffff8105c9e0>] ? manage_workers.clone.17+0x15b/0x15b
[258000.945010]  [<ffffffff8105c9e0>] ? manage_workers.clone.17+0x15b/0x15b
[258000.945019]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258000.945027]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258000.945036]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258000.945044]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258120.944114] INFO: task nfsd:12690 blocked for more than 120 seconds.
[258120.945449] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258120.946730] nfsd            D ffff880223cb5120     0 12690      2 0x00000000
[258120.946742]  ffff880223cb5120 0000000000000046 0000000000000282 0000000000000900
[258120.946755]  ffff880224ee1650 0000000000012800 ffff88010bccbfd8 ffff88010bccbfd8
[258120.946766]  0000000000012800 ffff880223cb5120 0000000000012800 0000000000012800
[258120.946776] Call Trace:
[258120.946793]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258120.946805]  [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[258120.946817]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258120.946828]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258120.946838]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258120.946847]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258120.946858]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258120.946867]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258120.946879]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258120.946890]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258120.946917]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258120.946929]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258120.946941]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258120.946950]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258120.946959]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258120.946969]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258120.947027]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258120.947039]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258120.947061]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258120.947082]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258120.947104]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258120.947130]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258120.947150]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258120.947178]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258120.947198]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258120.947218]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258120.947227]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258120.947238]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258120.947249]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258120.947259]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13
[258120.947268] INFO: task nfsd:12691 blocked for more than 120 seconds.
[258120.948607] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[258120.949975] nfsd            D ffff880185575610     0 12691      2 0x00000000
[258120.949988]  ffff880185575610 0000000000000046 0000000000000246 0000000000000001
[258120.950001]  ffff880185574f20 0000000000012800 ffff880185e83fd8 ffff880185e83fd8
[258120.950012]  0000000000012800 ffff880185575610 0000000000012800 0000000000012800
[258120.950024] Call Trace:
[258120.950035]  [<ffffffff8100e342>] ? read_tsc+0x5/0x14
[258120.950046]  [<ffffffff810b5eac>] ? lock_page+0x20/0x20
[258120.950056]  [<ffffffff8133576b>] ? io_schedule+0x5b/0x75
[258120.950066]  [<ffffffff810b5eb5>] ? sleep_on_page+0x9/0x10
[258120.950076]  [<ffffffff81335cee>] ? __wait_on_bit_lock+0x3c/0x85
[258120.950087]  [<ffffffff810b5137>] ? page_waitqueue+0x3/0x6d
[258120.950097]  [<ffffffff810b5e86>] ? __lock_page+0x5d/0x63
[258120.950107]  [<ffffffff810600ad>] ? autoremove_wake_function+0x2a/0x2a
[258120.950118]  [<ffffffff8111b14f>] ? __generic_file_splice_read+0x245/0x409
[258120.950141]  [<ffffffffa0624aaa>] ? put_cred+0x1c/0x1c [nfsd]
[258120.950151]  [<ffffffff81154d1d>] ? find_acceptable_alias+0x1f/0xe4
[258120.950163]  [<ffffffff8111a071>] ? page_cache_pipe_buf_release+0x12/0x12
[258120.950174]  [<ffffffff810383fc>] ? need_resched+0x1a/0x23
[258120.950183]  [<ffffffff8103840a>] ? should_resched+0x5/0x24
[258120.950193]  [<ffffffff8111b350>] ? generic_file_splice_read+0x3d/0x65
[258120.950242]  [<ffffffffa0526366>] ? xfs_file_splice_read+0xe5/0x12f [xfs]
[258120.950253]  [<ffffffff8111a1c7>] ? splice_direct_to_actor+0xb6/0x178
[258120.950274]  [<ffffffffa062591b>] ? dget+0x1e/0x1e [nfsd]
[258120.950293]  [<ffffffffa0625d79>] ? nfsd_vfs_read.clone.5+0x75/0x129 [nfsd]
[258120.950315]  [<ffffffffa0626703>] ? nfsd_read+0x1ca/0x231 [nfsd]
[258120.950340]  [<ffffffffa062d2ab>] ? nfsd3_proc_read+0xd0/0x111 [nfsd]
[258120.950360]  [<ffffffffa06227c6>] ? nfsd_dispatch+0xdf/0x1bd [nfsd]
[258120.950384]  [<ffffffffa056bcee>] ? svc_process+0x3d5/0x5e9 [sunrpc]
[258120.950404]  [<ffffffffa0622028>] ? nfsd_shutdown+0x28/0x28 [nfsd]
[258120.950423]  [<ffffffffa0622110>] ? nfsd+0xe8/0x131 [nfsd]
[258120.950432]  [<ffffffff8105fc0b>] ? kthread+0x7a/0x82
[258120.950442]  [<ffffffff8133ce24>] ? kernel_thread_helper+0x4/0x10
[258120.950452]  [<ffffffff8105fb91>] ? kthread_worker_fn+0x149/0x149
[258120.950461]  [<ffffffff8133ce20>] ? gs_change+0x13/0x13

The only questionable message before that is from kvm:

[180085.863989] kvm: page allocation failure: order:1, mode:0x20

Which is about 21 hours before the sas error. So it is (probably?) not related.

-- 
Thomas Fjellstrom
thomas@fjellstrom.ca

^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: mvsas errors in 3.0, URGENT
  2011-09-19  4:18 ` mvsas errors in 3.0 Thomas Fjellstrom
@ 2011-09-23  1:40   ` Thomas Fjellstrom
  0 siblings, 0 replies; 2+ messages in thread
From: Thomas Fjellstrom @ 2011-09-23  1:40 UTC (permalink / raw)
  To: Linux Kernel List; +Cc: linux-scsi, Xiangliang Yu, yxlraid

On September 18, 2011, Thomas Fjellstrom wrote:
> On September 16, 2011, Thomas Fjellstrom wrote:
> > Hi, its me again.
> > 
> > Just updated to 3.0 last night, after the card had locked up twice in as
> > many days. However, I just heard some unsettling noises come from my
> > raid array, like one of the disks was being re-initialized several
> > times. spinning up and down a few times, etc.
> > 
> > When I got to look at the logs, I find this:
> > 
[snip logs]
> > 
> > So, it seems to have at least recovered this time, rather than locking
> > up, unfortunately now my raid5 array is rebuilding. Thankfully it seems
> > to have been able to use the mdraid bitmap feature, as it only took 20
> > minutes.
> 
> So now 20+ hours after that, I get another error, and the card has locked
> up, but this time without trying to reinitialize anything.
> 
[snip logs]
> 
> The only questionable message before that is from kvm:
> 
> [180085.863989] kvm: page allocation failure: order:1, mode:0x20
> 
> Which is about 21 hours before the sas error. So it is (probably?) not
> related.


All right, new event just now. Drive started kicking on and off like before,
but this time, the kernel/card has decided to kick ALL of the drives in
succession.

logs from this go-round:

[336077.612307] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 2084:Release slot [6] tag[6], task [ffff8801d308c540]:
[336077.612332] sas: sas_ata_task_done: SAS error 8a
[336077.612366] sas: Enter sas_scsi_recover_host
[336077.612385] ata14: sas eh calling libata cmd error handler
[336077.612401] ata9: sas eh calling libata port error handler
[336077.612426] ata10: sas eh calling libata port error handler
[336077.612440] ata11: sas eh calling libata port error handler
[336077.612454] ata12: sas eh calling libata port error handler
[336077.612467] ata13: sas eh calling libata port error handler
[336077.612479] ata14: sas eh calling libata port error handler
[336077.612493] ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[336077.613795] ata14.00: failed command: FLUSH CACHE EXT
[336077.615073] ata14.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336077.615078]          res 01/04:00:f8:13:9d/00:00:26:00:00/40 Emask 0x12 (ATA bus error)
[336077.617623] ata14.00: status: { ERR }
[336077.618915] ata14.00: error: { ABRT }
[336077.620225] ata14: hard resetting link
[336077.620233] sas: sas_ata_hard_reset: Found ATA device.
[336077.622279] sas: sas_ata_task_done: SAS error 8a
[336077.622395] sas: sas_ata_task_done: SAS error 8a
[336077.622408] ata14.00: both IDENTIFYs aborted, assuming NODEV
[336077.622419] ata14.00: revalidation failed (errno=-2)
[336079.622296] sd 0:0:5:0: [sdi] Synchronizing SCSI cache
[336082.620081] ata14: hard resetting link
[336082.620101] sas: sas_ata_hard_reset: Found ATA device.
[336082.620131] ata14.00: failed to IDENTIFY (I/O error, err_mask=0x41)
[336082.620140] ata14.00: revalidation failed (errno=-5)
[336087.620036] ata14: hard resetting link
[336087.620048] sas: sas_ata_hard_reset: Found ATA device.
[336087.620078] ata14.00: failed to IDENTIFY (I/O error, err_mask=0x41)
[336087.620087] ata14.00: revalidation failed (errno=-5)
[336087.621409] ata14.00: disabled
[336087.621431] ata14: EH complete
[336087.621441] ata15: sas eh calling libata port error handler
[336087.621458] sas: --- Exit sas_scsi_recover_host
[336087.621532] md: super_written gets error=-5, uptodate=0
[336087.621543] md/raid:md1: Disk failure on sdi, disabling device.
[336087.621548] md/raid:md1: Operation continuing on 6 devices.
[336087.633709] sd 0:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336087.633726] sd 0:0:5:0: [sdi] Stopping disk
[336087.633753] sd 0:0:5:0: [sdi] START_STOP FAILED
[336087.633760] sd 0:0:5:0: [sdi]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336087.729909] RAID conf printout:
[336087.729919]  --- level:5 rd:7 wd:6
[336087.729927]  disk 0, o:1, dev:sdf
[336087.729933]  disk 1, o:1, dev:sdg
[336087.729939]  disk 2, o:1, dev:sdd
[336087.729944]  disk 3, o:1, dev:sde
[336087.729950]  disk 4, o:1, dev:sdj
[336087.729955]  disk 5, o:0, dev:sdi
[336087.729960]  disk 6, o:1, dev:sdh
[336087.780031] RAID conf printout:
[336087.780042]  --- level:5 rd:7 wd:6
[336087.780051]  disk 0, o:1, dev:sdf
[336087.780058]  disk 1, o:1, dev:sdg
[336087.780064]  disk 2, o:1, dev:sdd
[336087.780075]  disk 3, o:1, dev:sde
[336087.780081]  disk 4, o:1, dev:sdj
[336087.780087]  disk 6, o:1, dev:sdh
[336092.088009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336094.140009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336101.140008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336103.192008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336105.244008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336126.672008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336128.724020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336130.776027] mvsas 0000:04:00.0: Phy6 : No sig fis
[336132.828019] mvsas 0000:04:00.0: Phy6 : No sig fis
[336134.880020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336136.932028] mvsas 0000:04:00.0: Phy6 : No sig fis
[336138.984011] mvsas 0000:04:00.0: Phy6 : No sig fis
[336141.036007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336143.088028] mvsas 0000:04:00.0: Phy6 : No sig fis
[336145.140016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336147.192015] mvsas 0000:04:00.0: Phy6 : No sig fis
[336149.244008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336151.296008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336153.348016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336155.036013] sas: phy-0:6 added to port-0:5, phy_mask:0x40 ( 600000000000000)
[336155.039108] sas: DOING DISCOVERY on port 5, pid:241
[336155.040784] sas: couldn't normalize sense
[336155.040882] sas: couldn't normalize sense
[336155.041323] sas: couldn't normalize sense
[336155.041360] sas: couldn't normalize sense
[336155.041385] sas: couldn't normalize sense
[336155.041397] sas: DONE DISCOVERY on port 5, pid:241, result:-70
[336155.400022] mvsas 0000:04:00.0: Phy6 : No sig fis
[336157.036020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336157.452015] mvsas 0000:04:00.0: Phy6 : No sig fis
[336159.088011] mvsas 0000:04:00.0: Phy6 : No sig fis
[336159.504015] mvsas 0000:04:00.0: Phy6 : No sig fis
[336161.140019] mvsas 0000:04:00.0: Phy6 : No sig fis
[336161.556007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336163.192028] mvsas 0000:04:00.0: Phy6 : No sig fis
[336163.614344] mvsas 0000:04:00.0: Phy6 : No sig fis
[336165.052912] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336169.083708] mvsas 0000:04:00.0: Phy6 : No sig fis
[336171.094357] mvsas 0000:04:00.0: Phy6 : No sig fis
[336173.144028] mvsas 0000:04:00.0: Phy6 : No sig fis
[336175.196016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336177.248009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336178.764591] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336179.300010] mvsas 0000:04:00.0: Phy6 : No sig fis
[336180.772010] mvsas 0000:04:00.0: Phy6 : No sig fis
[336181.376430] mvsas 0000:04:00.0: Phy6 : No sig fis
[336182.824021] mvsas 0000:04:00.0: Phy6 : No sig fis
[336183.404026] mvsas 0000:04:00.0: Phy6 : No sig fis
[336184.876009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336185.456027] mvsas 0000:04:00.0: Phy6 : No sig fis
[336186.104503] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336186.928025] mvsas 0000:04:00.0: Phy6 : No sig fis
[336187.508027] mvsas 0000:04:00.0: Phy6 : No sig fis
[336188.104009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336189.016735] mvsas 0000:04:00.0: Phy6 : No sig fis
[336189.560026] mvsas 0000:04:00.0: Phy6 : No sig fis
[336190.156010] mvsas 0000:04:00.0: Phy6 : No sig fis
[336191.032009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336191.612007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336191.954511] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336204.656009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336206.708027] mvsas 0000:04:00.0: Phy6 : No sig fis
[336208.760017] mvsas 0000:04:00.0: Phy6 : No sig fis
[336210.592819] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336215.904035] sas: command 0xffff880132eb5b80, task 0xffff88018ecb7640, timed out: BLK_EH_NOT_HANDLED
[336215.904053] sas: command 0xffff88022310c280, task 0xffff88018ecb7d40, timed out: BLK_EH_NOT_HANDLED
[336215.904071] sas: command 0xffff88022310c480, task 0xffff88018ecb72c0, timed out: BLK_EH_NOT_HANDLED
[336215.904087] sas: command 0xffff880101c4a9c0, task 0xffff8801be42ae00, timed out: BLK_EH_NOT_HANDLED
[336215.904101] sas: command 0xffff880101c4adc0, task 0xffff88018ecb7480, timed out: BLK_EH_NOT_HANDLED
[336215.904115] sas: command 0xffff8800c16acd80, task 0xffff88018ecb7100, timed out: BLK_EH_NOT_HANDLED
[336215.904243] sas: Enter sas_scsi_recover_host
[336215.904251] sas: trying to find task 0xffff88018ecb7d40
[336215.904259] sas: sas_scsi_find_task: aborting task 0xffff88018ecb7d40
[336215.904273] sas: sas_scsi_find_task: querying task 0xffff88018ecb7d40
[336215.904282] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336215.904295] sas: sas_scsi_find_task: task 0xffff88018ecb7d40 failed to abort
[336215.904303] sas: task 0xffff88018ecb7d40 is not at LU: I_T recover
[336215.904311] sas: I_T nexus reset for dev 0500000000000000
[336216.019328] sas: sas_form_port: phy5 belongs to port4 already(1)!
[336216.436020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336218.112077] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[4]:rc= 0
[336218.112097] sas: I_T 0500000000000000 recovered
[336218.112107] sas: sas_ata_task_done: SAS error 8d
[336218.112123] sas: trying to find task 0xffff88018ecb72c0
[336218.112130] sas: sas_scsi_find_task: aborting task 0xffff88018ecb72c0
[336218.112142] sas: sas_scsi_find_task: querying task 0xffff88018ecb72c0
[336218.112151] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336218.112163] sas: sas_scsi_find_task: task 0xffff88018ecb72c0 failed to abort
[336218.112171] sas: task 0xffff88018ecb72c0 is not at LU: I_T recover
[336218.112178] sas: I_T nexus reset for dev 0700000000000000
[336218.252109] sas: sas_form_port: phy7 belongs to port6 already(1)!
[336218.488009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336218.692478] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336220.320045] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[6]:rc= 0
[336220.320065] sas: I_T 0700000000000000 recovered
[336220.320075] sas: sas_ata_task_done: SAS error 8d
[336220.320090] sas: trying to find task 0xffff8801be42ae00
[336220.320097] sas: sas_scsi_find_task: aborting task 0xffff8801be42ae00
[336220.320109] sas: sas_scsi_find_task: querying task 0xffff8801be42ae00
[336220.320118] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336220.320130] sas: sas_scsi_find_task: task 0xffff8801be42ae00 failed to abort
[336220.320138] sas: task 0xffff8801be42ae00 is not at LU: I_T recover
[336220.320145] sas: I_T nexus reset for dev 0200000000000000
[336220.461268] sas: sas_form_port: phy2 belongs to port2 already(1)!
[336220.540007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336221.112022] mvsas 0000:04:00.0: Phy6 : No sig fis
[336222.528044] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[2]:rc= 0
[336222.528064] sas: I_T 0200000000000000 recovered
[336222.528074] sas: sas_ata_task_done: SAS error 8d
[336222.528092] sas: trying to find task 0xffff88018ecb7480
[336222.528100] sas: sas_scsi_find_task: aborting task 0xffff88018ecb7480
[336222.528112] sas: sas_scsi_find_task: querying task 0xffff88018ecb7480
[336222.528121] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336222.528133] sas: sas_scsi_find_task: task 0xffff88018ecb7480 failed to abort
[336222.528141] sas: task 0xffff88018ecb7480 is not at LU: I_T recover
[336222.528148] sas: I_T nexus reset for dev 0100000000000000
[336222.668186] sas: sas_form_port: phy1 belongs to port1 already(1)!
[336222.672128] mvsas 0000:04:00.0: Phy6 : No sig fis
[336223.164010] mvsas 0000:04:00.0: Phy6 : No sig fis
[336224.736650] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[1]:rc= 0
[336224.724018] mvsas 0000:04:00.0: Phy6 : No sig fis
[336224.770012] sas: I_T 0100000000000000 recovered
[336224.770023] sas: sas_ata_task_done: SAS error 8d
[336224.770038] sas: trying to find task 0xffff88018ecb7640
[336224.770045] sas: sas_scsi_find_task: aborting task 0xffff88018ecb7640
[336224.770059] sas: sas_scsi_find_task: querying task 0xffff88018ecb7640
[336224.770068] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336224.770081] sas: sas_scsi_find_task: task 0xffff88018ecb7640 failed to abort
[336224.770089] sas: task 0xffff88018ecb7640 is not at LU: I_T recover
[336224.770096] sas: I_T nexus reset for dev 0300000000000000
[336224.893130] sas: sas_form_port: phy3 belongs to port3 already(1)!
[336225.216016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336226.776017] mvsas 0000:04:00.0: Phy6 : No sig fis
[336226.976056] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[3]:rc= 0
[336226.976077] sas: I_T 0300000000000000 recovered
[336226.976086] sas: sas_ata_task_done: SAS error 8d
[336226.976100] sas: trying to find task 0xffff88018ecb7100
[336226.976107] sas: sas_scsi_find_task: aborting task 0xffff88018ecb7100
[336226.976119] sas: sas_scsi_find_task: querying task 0xffff88018ecb7100
[336226.976128] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1747:mvs_query_task:rc= 5
[336226.976140] sas: sas_scsi_find_task: task 0xffff88018ecb7100 failed to abort
[336226.976148] sas: task 0xffff88018ecb7100 is not at LU: I_T recover
[336226.976155] sas: I_T nexus reset for dev 0000000000000000
[336227.115496] sas: sas_form_port: phy0 belongs to port0 already(1)!
[336227.268016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336228.828006] mvsas 0000:04:00.0: Phy6 : No sig fis
[336229.184058] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[0]:rc= 0
[336229.184078] sas: I_T 0000000000000000 recovered
[336229.184126] sas: sas_ata_task_done: SAS error 8d
[336229.184142] ata9: sas eh calling libata port error handler
[336229.184160] ata9.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336229.185461] ata9.00: failed command: FLUSH CACHE EXT
[336229.186719] ata9.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336229.186725]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336229.189330] ata9.00: status: { ERR }
[336229.190637] ata9.00: error: { ABRT }
[336229.191928] ata9: hard resetting link
[336229.332843] sas: sas_form_port: phy0 belongs to port0 already(1)!
[336229.362079] mvsas 0000:04:00.0: Phy6 : No sig fis
[336230.231814] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336231.396036] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[0]:rc= 0
[336231.396057] sas: sas_ata_hard_reset: Found ATA device.
[336231.396123] sas: sas_ata_task_done: SAS error 2
[336231.396375] sas: sas_ata_task_done: SAS error 2
[336231.396398] ata9.00: both IDENTIFYs aborted, assuming NODEV
[336231.396408] ata9.00: revalidation failed (errno=-2)
[336236.396046] ata9: hard resetting link
[336236.536967] sas: sas_form_port: phy0 belongs to port0 already(1)!
[336238.604053] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[0]:rc= 0
[336238.604073] sas: sas_ata_hard_reset: Found ATA device.
[336238.605307] sas: sas_ata_task_done: SAS error 2
[336238.605345] ata9.00: both IDENTIFYs aborted, assuming NODEV
[336238.605357] ata9.00: revalidation failed (errno=-2)
[336240.043050] sas: phy-0:6 added to port-0:5, phy_mask:0x40 ( 600000000000000)
[336240.043087] sas: DOING DISCOVERY on port 5, pid:241
[336240.043284] sas: couldn't normalize sense
[336240.043419] sas: couldn't normalize sense
[336240.044275] sas: couldn't normalize sense
[336240.044544] sas: couldn't normalize sense
[336240.044571] sas: couldn't normalize sense
[336240.044582] sas: DONE DISCOVERY on port 5, pid:241, result:-70
[336242.043419] mvsas 0000:04:00.0: Phy6 : No sig fis
[336243.604046] ata9: hard resetting link
[336243.745079] sas: sas_form_port: phy0 belongs to port0 already(1)!
[336244.092008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336244.279844] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336245.812054] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[0]:rc= 0
[336245.812074] sas: sas_ata_hard_reset: Found ATA device.
[336245.813309] sas: sas_ata_task_done: SAS error 2
[336245.813328] ata9.00: both IDENTIFYs aborted, assuming NODEV
[336245.813337] ata9.00: revalidation failed (errno=-2)
[336245.814641] ata9.00: disabled
[336245.814670] ata9: EH complete
[336245.814680] ata10: sas eh calling libata port error handler
[336245.814697] ata10.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336245.815988] ata10.00: failed command: FLUSH CACHE EXT
[336245.817315] ata10.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336245.817320]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336245.819970] ata10.00: status: { ERR }
[336245.821318] ata10.00: error: { ABRT }
[336245.821332] ata10: hard resetting link
[336245.961948] sas: sas_form_port: phy1 belongs to port1 already(1)!
[336246.144015] mvsas 0000:04:00.0: Phy6 : No sig fis
[336246.335759] mvsas 0000:04:00.0: Phy6 : No sig fis
[336248.028054] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[1]:rc= 0
[336248.028074] sas: sas_ata_hard_reset: Found ATA device.
[336248.029238] sas: sas_ata_task_done: SAS error 2
[336248.029261] ata10.00: both IDENTIFYs aborted, assuming NODEV
[336248.029270] ata10.00: revalidation failed (errno=-2)
[336248.196020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336248.384016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336248.576916] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336250.248019] mvsas 0000:04:00.0: Phy6 : No sig fis
[336250.436009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336251.004009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336252.300029] mvsas 0000:04:00.0: Phy6 : No sig fis
[336252.488004] mvsas 0000:04:00.0: Phy6 : No sig fis
[336253.028066] ata10: hard resetting link
[336253.056499] mvsas 0000:04:00.0: Phy6 : No sig fis
[336253.210941] sas: sas_form_port: phy1 belongs to port1 already(1)!
[336254.352012] mvsas 0000:04:00.0: Phy6 : No sig fis
[336254.540025] mvsas 0000:04:00.0: Phy6 : No sig fis
[336255.236072] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[1]:rc= 0
[336255.216024] mvsas 0000:04:00.0: Phy6 : No sig fis
[336255.261731] sas: sas_ata_hard_reset: Found ATA device.
[336255.262912] sas: sas_ata_task_done: SAS error 2
[336255.262928] ata10.00: both IDENTIFYs aborted, assuming NODEV
[336255.262937] ata10.00: revalidation failed (errno=-2)
[336256.441487] mvsas 0000:04:00.0: Phy6 : No sig fis
[336256.592011] mvsas 0000:04:00.0: Phy6 : No sig fis
[336257.268022] mvsas 0000:04:00.0: Phy6 : No sig fis
[336257.890198] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336258.456008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336258.644027] mvsas 0000:04:00.0: Phy6 : No sig fis
[336259.320009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336259.888012] mvsas 0000:04:00.0: Phy6 : No sig fis
[336260.260040] ata10: hard resetting link
[336260.400925] sas: sas_form_port: phy1 belongs to port1 already(1)!
[336260.508008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336260.696016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336261.372023] mvsas 0000:04:00.0: Phy6 : No sig fis
[336261.940009] mvsas 0000:04:00.0: Phy6 : No sig fis
[336262.134525] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336262.468065] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[1]:rc= 0
[336262.468085] sas: sas_ata_hard_reset: Found ATA device.
[336262.469277] sas: sas_ata_task_done: SAS error 2
[336262.469293] ata10.00: both IDENTIFYs aborted, assuming NODEV
[336262.469303] ata10.00: revalidation failed (errno=-2)
[336262.470547] ata10.00: disabled
[336262.470574] ata10: EH complete
[336262.470584] ata11: sas eh calling libata port error handler
[336262.470600] ata11.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336262.471840] ata11.00: failed command: FLUSH CACHE EXT
[336262.473107] ata11.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336262.473112]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336262.475588] ata11.00: status: { ERR }
[336262.476877] ata11.00: error: { ABRT }
[336262.478130] ata11: hard resetting link
[336262.618411] sas: sas_form_port: phy2 belongs to port2 already(1)!
[336262.632358] mvsas 0000:04:00.0: Phy6 : No sig fis
[336262.748013] mvsas 0000:04:00.0: Phy6 : No sig fis
[336263.424007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336263.992007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336264.624020] mvsas 0000:04:00.0: Phy6 : No sig fis
[336264.684012] mvsas 0000:04:00.0: Phy6 : No sig fis
[336264.729914] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[2]:rc= 0
[336264.729938] sas: sas_ata_hard_reset: Found ATA device.
[336264.731152] sas: sas_ata_task_done: SAS error 2
[336264.731168] ata11.00: both IDENTIFYs aborted, assuming NODEV
[336264.731178] ata11.00: revalidation failed (errno=-2)
[336264.800016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336265.476014] mvsas 0000:04:00.0: Phy6 : No sig fis
[336266.044007] mvsas 0000:04:00.0: Phy6 : No sig fis
[336266.740249] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336269.728057] ata11: hard resetting link
[336269.868007] sas: sas_form_port: phy2 belongs to port2 already(1)!
[336270.931312] sas: phy-0:6 added to port-0:5, phy_mask:0x40 ( 600000000000000)
[336270.931348] sas: DOING DISCOVERY on port 5, pid:234
[336270.933271] sas: DONE DISCOVERY on port 5, pid:234, result:0
[336271.936042] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[2]:rc= 0
[336271.936062] sas: sas_ata_hard_reset: Found ATA device.
[336271.937244] sas: sas_ata_task_done: SAS error 2
[336271.937261] ata11.00: both IDENTIFYs aborted, assuming NODEV
[336271.937270] ata11.00: revalidation failed (errno=-2)
[336273.524008] mvsas 0000:04:00.0: Phy6 : No sig fis
[336275.576025] mvsas 0000:04:00.0: Phy6 : No sig fis
[336275.694665] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336276.936088] ata11: hard resetting link
[336276.971509] sas: sas_form_port: phy2 belongs to port2 already(1)!
[336277.638416] mvsas 0000:04:00.0: Phy6 : No sig fis
[336278.280016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336279.144039] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[2]:rc= 0
[336279.144059] sas: sas_ata_hard_reset: Found ATA device.
[336279.145261] sas: sas_ata_task_done: SAS error 2
[336279.145279] ata11.00: both IDENTIFYs aborted, assuming NODEV
[336279.145288] ata11.00: revalidation failed (errno=-2)
[336279.146535] ata11.00: disabled
[336279.146564] ata11: EH complete
[336279.146574] ata12: sas eh calling libata port error handler
[336279.146590] ata12.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336279.147804] ata12.00: failed command: FLUSH CACHE EXT
[336279.149073] ata12.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336279.149078]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336279.151637] ata12.00: status: { ERR }
[336279.152933] ata12.00: error: { ABRT }
[336279.154183] ata12: hard resetting link
[336279.277325] sas: sas_form_port: phy3 belongs to port3 already(1)!
[336279.680712] mvsas 0000:04:00.0: Phy6 : No sig fis
[336280.332023] mvsas 0000:04:00.0: Phy6 : No sig fis
[336281.360053] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[3]:rc= 0
[336281.360072] sas: sas_ata_hard_reset: Found ATA device.
[336281.361255] sas: sas_ata_task_done: SAS error 2
[336281.361271] ata12.00: both IDENTIFYs aborted, assuming NODEV
[336281.361280] ata12.00: revalidation failed (errno=-2)
[336281.732028] mvsas 0000:04:00.0: Phy6 : No sig fis
[336282.384019] mvsas 0000:04:00.0: Phy6 : No sig fis
[336283.784025] mvsas 0000:04:00.0: Phy6 : No sig fis
[336284.436016] mvsas 0000:04:00.0: Phy6 : No sig fis
[336285.836018] mvsas 0000:04:00.0: Phy6 : No sig fis
[336286.360058] ata12: hard resetting link
[336286.483412] sas: sas_form_port: phy3 belongs to port3 already(1)!
[336286.488013] mvsas 0000:04:00.0: Phy6 : No sig fis
[336287.096103] sas: sas_form_port: phy6 belongs to port5 already(1)!
[336288.568067] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[3]:rc= 0
[336288.568087] sas: sas_ata_hard_reset: Found ATA device.
[336288.569263] sas: sas_ata_task_done: SAS error 2
[336288.569279] ata12.00: both IDENTIFYs aborted, assuming NODEV
[336288.569288] ata12.00: revalidation failed (errno=-2)
[336293.568068] ata12: hard resetting link
[336293.691475] sas: sas_form_port: phy3 belongs to port3 already(1)!
[336295.776058] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[3]:rc= 0
[336295.776078] sas: sas_ata_hard_reset: Found ATA device.
[336295.777251] sas: sas_ata_task_done: SAS error 2
[336295.777268] ata12.00: both IDENTIFYs aborted, assuming NODEV
[336295.777277] ata12.00: revalidation failed (errno=-2)
[336295.778477] ata12.00: disabled
[336295.778505] ata12: EH complete
[336295.778515] ata13: sas eh calling libata port error handler
[336295.778531] ata13.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336295.779727] ata13.00: failed command: FLUSH CACHE EXT
[336295.780959] ata13.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336295.780964]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336295.783398] ata13.00: status: { ERR }
[336295.784635] ata13.00: error: { ABRT }
[336295.785840] ata13: hard resetting link
[336295.908875] sas: sas_form_port: phy5 belongs to port4 already(1)!
[336297.992120] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[4]:rc= 0
[336297.992141] sas: sas_ata_hard_reset: Found ATA device.
[336297.993387] sas: sas_ata_task_done: SAS error 2
[336297.993424] ata13.00: both IDENTIFYs aborted, assuming NODEV
[336297.993436] ata13.00: revalidation failed (errno=-2)
[336302.992048] ata13: hard resetting link
[336303.114876] sas: sas_form_port: phy5 belongs to port4 already(1)!
[336305.200055] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[4]:rc= 0
[336305.200075] sas: sas_ata_hard_reset: Found ATA device.
[336305.201298] sas: sas_ata_task_done: SAS error 2
[336305.201316] ata13.00: both IDENTIFYs aborted, assuming NODEV
[336305.201325] ata13.00: revalidation failed (errno=-2)
[336310.200068] ata13: hard resetting link
[336310.322919] sas: sas_form_port: phy5 belongs to port4 already(1)!
[336312.408040] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[4]:rc= 0
[336312.408060] sas: sas_ata_hard_reset: Found ATA device.
[336312.409251] sas: sas_ata_task_done: SAS error 2
[336312.409269] ata13.00: both IDENTIFYs aborted, assuming NODEV
[336312.409277] ata13.00: revalidation failed (errno=-2)
[336312.410467] ata13.00: disabled
[336312.410498] ata13: EH complete
[336312.410509] ata15: sas eh calling libata port error handler
[336312.410524] ata15.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 t0
[336312.411712] ata15.00: failed command: FLUSH CACHE EXT
[336312.412941] ata15.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0
[336312.412946]          res 01/04:00:02:00:00/00:00:00:00:00/40 Emask 0x3 (HSM violation)
[336312.415324] ata15.00: status: { ERR }
[336312.416496] ata15.00: error: { ABRT }
[336312.417633] ata15: hard resetting link
[336312.558061] sas: sas_form_port: phy7 belongs to port6 already(1)!
[336314.624041] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[6]:rc= 0
[336314.624061] sas: sas_ata_hard_reset: Found ATA device.
[336314.625268] sas: sas_ata_task_done: SAS error 2
[336314.625284] ata15.00: both IDENTIFYs aborted, assuming NODEV
[336314.625293] ata15.00: revalidation failed (errno=-2)
[336319.628017] ata15: hard resetting link
[336319.770143] sas: sas_form_port: phy7 belongs to port6 already(1)!
[336321.836042] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[6]:rc= 0
[336321.836063] sas: sas_ata_hard_reset: Found ATA device.
[336321.837273] sas: sas_ata_task_done: SAS error 2
[336321.837298] ata15.00: both IDENTIFYs aborted, assuming NODEV
[336321.837307] ata15.00: revalidation failed (errno=-2)
[336326.836070] ata15: hard resetting link
[336326.977246] sas: sas_form_port: phy7 belongs to port6 already(1)!
[336329.048032] /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/drivers/scsi/mvsas/mv_sas.c 1701:mvs_I_T_nexus_reset for device[6]:rc= 0
[336329.048052] sas: sas_ata_hard_reset: Found ATA device.
[336329.049249] sas: sas_ata_task_done: SAS error 2
[336329.049271] ata15.00: both IDENTIFYs aborted, assuming NODEV
[336329.049280] ata15.00: revalidation failed (errno=-2)
[336329.050385] ata15.00: disabled
[336329.050412] ata15: EH complete
[336329.050420] sas: --- Exit sas_scsi_recover_host
[336329.050667] sd 0:0:0:0: [sdd] Unhandled error code
[336329.050675] sd 0:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050686] sd 0:0:0:0: [sdd] CDB: Read(10): 28 00 3c 89 aa
[336329.050709] sd 0:0:0:0: [sdd] Unhandled error code
[336329.050719] sd 0:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050733] sd 0:0:0:0: [sdd] CDB: Write(10) 80 00 00 08 00
[336329.050749] end_request: I/O error, dev sdd, sector 1015655040
[336329.050772] sd 0:0:0:0: [sdd] Unhandled error code
[336329.050778] sd 0:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050786] sd 0:0:0:0: [sdd] CDB: Read(10): 28 00 73 0d 65 08 00 00 c0 00
[336329.050801] end_request: I/O error, dev sdd, sector 1930257672
[336329.050817] sd 0:0:0:0: [sdd] Unhandled error code
[336329.050823] sd 0:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050831] sd 0:0:0:0: [sdd] CDB: Read(10): 28 00 73 0d 65 e8 00 03 20 00
[336329.050845] end_request: I/O error, dev sdd, sector 1930257896
[336329.050905] sd 0:0:3:0: [sdg] Unhandled error code
[336329.050911] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050920] sd 0:0:3:0: [sdg] CDB: Read(10): 28 00 26 9c a8 78 00 00 08 00
[336329.050933] end_request: I/O error, dev sdg, sector 647800952
[336329.050947] sd 0:0:3:0: [sdg] Unhandled error code
[336329.050952] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.050961] sd 0:0:3:0: [sdg] CDB: Read(10): 28 00 26 9c a8 c8 00 00 08 00
[336329.050974] end_request: I/O error, dev sdg, sector 647801032
[336329.051082] sd 0:0:1:0: [sde] Unhandled error code
[336329.051087] sd 0:0:1:0: [sde]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051096] sd 0:0:1:0: [sde] CDB: Write(10): 2a 00 00 00 00 00 00 00 02 00
[336329.051109] end_request: I/O error, dev sde, sector 0
[336329.051117] end_request: I/O error, dev sde, sector 0
[336329.051123] md: super_written gets error=-5, uptodate=0
[336329.051133] md/raid:md1: Disk failure on sde, disabling device.
[336329.051137] md/raid:md1: Operation continuing on 5 devices.
[336329.051160] sd 0:0:1:0: [sde] Unhandled error code
[336329.051165] sd 0:0:1:0: [sde]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051174] sd 0:0:1:0: [sde] CDB: Read(10): 28 00 26 86 3d b0 00 00 10 00
[336329.051187] end_request: I/O error, dev sde, sector 646331824
[336329.051205] sd 0:0:1:0: [sde] Unhandled error code
[336329.051211] sd 0:0:1:0: [sde]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051219] sd 0:0:1:0: [sde] CDB: Read(10): 28 00 73 0d 65 08 00 04 00 00
[336329.051233] end_request: I/O error, dev sde, sector 1930257672
[336329.051250] sd 0:0:2:0: [sdf] Unhandled error code
[336329.051256] sd 0:0:2:0: [sdf]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051264] sd 0:0:2:0: [sdf] CDB: Write(10): 2a 00 00 00 00 00 00 00 02 00
[336329.051277] end_request: I/O error, dev sdf, sector 0
[336329.051285] end_request: I/O error, dev sdf, sector 0
[336329.051291] md: super_written gets error=-5, uptodate=0
[336329.051300] md/raid:md1: Disk failure on sdf, disabling device.
[336329.051303] md/raid:md1: Operation continuing on 4 devices.
[336329.051319] sd 0:0:2:0: [sdf] Unhandled error code
[336329.051325] sd 0:0:2:0: [sdf]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051333] sd 0:0:2:0: [sdf] CDB: Read(10): 28 00 73 0d 65 08 00 04 00 00
[336329.051347] end_request: I/O error, dev sdf, sector 1930257672
[336329.051364] sd 0:0:4:0: [sdh] Unhandled error code
[336329.051369] sd 0:0:4:0: [sdh]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051378] sd 0:0:4:0: [sdh] CDB: Write(10): 2a 00 00 00 00 00 00 00 02 00
[336329.051391] end_request: I/O error, dev sdh, sector 0
[336329.051398] end_request: I/O error, dev sdh, sector 0
[336329.051404] md: super_written gets error=-5, uptodate=0
[336329.051411] md/raid:md1: Disk failure on sdh, disabling device.
[336329.051415] md/raid:md1: Operation continuing on 3 devices.
[336329.051426] sd 0:0:4:0: [sdh] Unhandled error code
[336329.051432] sd 0:0:4:0: [sdh]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051440] sd 0:0:4:0: [sdh] CDB: Read(10): 28 00 26 9b e4 c0 00 00 08 00
[336329.051454] end_request: I/O error, dev sdh, sector 647750848
[336329.051470] sd 0:0:4:0: [sdh] Unhandled error code
[336329.051475] sd 0:0:4:0: [sdh]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051484] sd 0:0:4:0: [sdh] CDB: Read(10): 28 00 73 0d 65 b0 00 04 00 00
[336329.051497] end_request: I/O error, dev sdh, sector 1930257840
[336329.051514] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051519] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051528] sd 0:0:6:0: [sdj] CDB: Write(10): 2a 00 00 00 00 00 00 00 02 00
[336329.051541] end_request: I/O error, dev sdj, sector 0
[336329.051548] end_request: I/O error, dev sdj, sector 0
[336329.051553] md: super_written gets error=-5, uptodate=0
[336329.051561] md/raid:md1: Disk failure on sdj, disabling device.
[336329.051565] md/raid:md1: Operation continuing on 2 devices.
[336329.051576] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051581] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051590] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a5 90 00 00 08 00
[336329.051603] end_request: I/O error, dev sdj, sector 647800208
[336329.051615] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051620] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051629] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a6 18 00 00 08 00
[336329.051642] end_request: I/O error, dev sdj, sector 647800344
[336329.051653] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051659] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051667] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a6 28 00 00 08 00
[336329.051680] end_request: I/O error, dev sdj, sector 647800360
[336329.051691] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051697] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051705] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a0 b0 00 00 08 00
[336329.051719] end_request: I/O error, dev sdj, sector 647798960
[336329.051730] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051735] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051743] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a0 70 00 00 08 00
[336329.051757] end_request: I/O error, dev sdj, sector 647798896
[336329.051768] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051774] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051782] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c a0 00 00 00 20 00
[336329.051795] end_request: I/O error, dev sdj, sector 647798784
[336329.051807] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051812] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051821] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 26 9c 9f e8 00 00 10 00
[336329.051834] end_request: I/O error, dev sdj, sector 647798760
[336329.051845] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051850] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051859] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 69 32 95 60 00 00 08 00
[336329.051872] end_request: I/O error, dev sdj, sector 1764922720
[336329.051887] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051893] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051901] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 73 0d 62 e8 00 03 18 00
[336329.051915] end_request: I/O error, dev sdj, sector 1930257128
[336329.051932] sd 0:0:6:0: [sdj] Unhandled error code
[336329.051937] sd 0:0:6:0: [sdj]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.051946] sd 0:0:6:0: [sdj] CDB: Read(10): 28 00 73 0d 66 00 00 03 08 00
[336329.051959] end_request: I/O error, dev sdj, sector 1930257920
[336329.192371] : 2a 00 00 00 00 00 00 00 02 00
[336329.192388] end_request: I/O error, dev sdd, sector 0
[336329.195799] end_request: I/O error, dev sdd, sector 0
[336329.196244] md: super_written gets error=-5, uptodate=0
[336329.196244] md/raid:md1: Disk failure on sdd, disabling device.
[336329.196244] md/raid:md1: Operation continuing on 1 devices.
[336329.206083] sd 0:0:3:0: [sdg] Unhandled error code
[336329.206090] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.206104] sd 0:0:3:0: [sdg] CDB: Write(10): 2a 00 00 00 00 00 00 00 02 00
[336329.206175] end_request: I/O error, dev sdg, sector 0
[336329.209586] end_request: I/O error, dev sdg, sector 0
[336329.212880] md: super_written gets error=-5, uptodate=0
[336329.212888] md/raid:md1: Disk failure on sdg, disabling device.
[336329.212893] md/raid:md1: Operation continuing on 0 devices.
[336329.219534] sd 0:0:3:0: [sdg] Unhandled error code
[336329.219545] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.219562] sd 0:0:3:0: [sdg] CDB: Read(10):
[336329.219580] RAID conf printout:
[336329.219590]  --- level:5 rd:7 wd:0
[336329.219600]  disk 0, o:0, dev:sdf
[336329.219608]  28 00 3c 89 a9 c0 00 00 08 00
[336329.219642] end_request: I/O error, dev sdg, sector 1015654848
[336329.219663] sd 0:0:3:0: [sdg] Unhandled error code
[336329.219670] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.219682] sd 0:0:3:0: [sdg] CDB: Read(10): 28 00 73 0d 65 08 00 01 60 00
[336329.219710] end_request: I/O error, dev sdg, sector 1930257672
[336329.219728] sd 0:0:3:0: [sdg] Unhandled error code
[336329.219735] sd 0:0:3:0: [sdg]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[336329.219747] sd 0:0:3:0: [sdg] CDB: Read(10): 28 00 73 0d 66 88 00 02 80 00
[336329.219776] end_request: I/O error, dev sdg, sector 1930258056
[336329.222304]  disk 1, o:0, dev:sdg
[336329.222310]  disk 2, o:0, dev:sdd
[336329.222315]  disk 3, o:0, dev:sde
[336329.222321]  disk 4, o:0, dev:sdj
[336329.222326]  disk 6, o:0, dev:sdh
[336329.264049] RAID conf printout:
[336329.264058]  --- level:5 rd:7 wd:0
[336329.264065]  disk 1, o:0, dev:sdg
[336329.264071]  disk 2, o:0, dev:sdd
[336329.264076]  disk 3, o:0, dev:sde
[336329.264081]  disk 4, o:0, dev:sdj
[336329.264087]  disk 6, o:0, dev:sdh
[336329.264103] RAID conf printout:
[336329.264108]  --- level:5 rd:7 wd:0
[336329.264114]  disk 1, o:0, dev:sdg
[336329.264119]  disk 2, o:0, dev:sdd
[336329.264124]  disk 3, o:0, dev:sde
[336329.264129]  disk 4, o:0, dev:sdj
[336329.264134]  disk 6, o:0, dev:sdh
[336329.312133] RAID conf printout:
[336329.312142]  --- level:5 rd:7 wd:0
[336329.312149]  disk 1, o:0, dev:sdg
[336329.312155]  disk 2, o:0, dev:sdd
[336329.312160]  disk 3, o:0, dev:sde
[336329.312166]  disk 4, o:0, dev:sdj
[336329.312180] RAID conf printout:
[336329.312185]  --- level:5 rd:7 wd:0
[336329.312190]  disk 1, o:0, dev:sdg
[336329.312195]  disk 2, o:0, dev:sdd
[336329.312200]  disk 3, o:0, dev:sde
[336329.312205]  disk 4, o:0, dev:sdj
[336329.380056] RAID conf printout:
[336329.380065]  --- level:5 rd:7 wd:0
[336329.380072]  disk 1, o:0, dev:sdg
[336329.380077]  disk 2, o:0, dev:sdd
[336329.380083]  disk 3, o:0, dev:sde
[336329.380098] RAID conf printout:
[336329.380103]  --- level:5 rd:7 wd:0
[336329.380108]  disk 1, o:0, dev:sdg
[336329.380113]  disk 2, o:0, dev:sdd
[336329.380118]  disk 3, o:0, dev:sde
[336329.416082] RAID conf printout:
[336329.416092]  --- level:5 rd:7 wd:0
[336329.416100]  disk 1, o:0, dev:sdg
[336329.416107]  disk 2, o:0, dev:sdd
[336329.416121] RAID conf printout:
[336329.416126]  --- level:5 rd:7 wd:0
[336329.416131]  disk 1, o:0, dev:sdg
[336329.416137]  disk 2, o:0, dev:sdd
[336329.416312] RAID conf printout:
[336329.416322]  --- level:5 rd:7 wd:0
[336329.416330]  disk 1, o:0, dev:sdg
[336329.416346] RAID conf printout:
[336329.416352]  --- level:5 rd:7 wd:0
[336329.416357]  disk 1, o:0, dev:sdg
[336329.420507] RAID conf printout:
[336329.420515]  --- level:5 rd:7 wd:0
[336329.429210] XFS (md1): I/O error occurred: meta-data dev md1 block 0xe92f0bf8       ("xfs_trans_read_buf") error 5 buf count 4096
[336329.429341] Buffer I/O error on device md1, logical block 485972532
[336329.429348] lost page write due to I/O error on md1
[336329.429360] Buffer I/O error on device md1, logical block 485972533
[336329.429366] lost page write due to I/O error on md1
[336329.429374] Buffer I/O error on device md1, logical block 485972534
[336329.429380] lost page write due to I/O error on md1
[336329.429387] Buffer I/O error on device md1, logical block 485972535
[336329.429392] lost page write due to I/O error on md1
[336329.429399] Buffer I/O error on device md1, logical block 485972536
[336329.429405] lost page write due to I/O error on md1
[336329.429412] Buffer I/O error on device md1, logical block 485972537
[336329.429417] lost page write due to I/O error on md1
[336329.429424] Buffer I/O error on device md1, logical block 485972538
[336329.429430] lost page write due to I/O error on md1
[336329.429437] Buffer I/O error on device md1, logical block 485972539
[336329.429443] lost page write due to I/O error on md1
[336329.429450] Buffer I/O error on device md1, logical block 485972540
[336329.429456] lost page write due to I/O error on md1
[336329.429462] Buffer I/O error on device md1, logical block 485972541
[336329.429468] lost page write due to I/O error on md1
[336329.431515] XFS (md1): I/O error occurred: meta-data dev md1 block 0xe90ebca8       ("xlog_iodone") error 5 buf count 32768
[336329.431531] XFS (md1): xfs_do_force_shutdown(0x2) called from line 891 of file /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/fs/xfs/xfs_log.c.  Return address = 0xffffffffa050a758
[336329.431598] XFS (md1): Log I/O Error Detected.  Shutting down filesystem
[336329.431606] XFS (md1): Please umount the filesystem and rectify the problem(s)
[336359.520105] XFS (md1): xfs_log_force: error 5 returned.
[336389.600065] XFS (md1): xfs_log_force: error 5 returned.
[336419.680073] XFS (md1): xfs_log_force: error 5 returned.
[336449.760067] XFS (md1): xfs_log_force: error 5 returned.
[336479.840083] XFS (md1): xfs_log_force: error 5 returned.
[336509.920068] XFS (md1): xfs_log_force: error 5 returned.
[336533.065989] nfsd: non-standard errno: 5
[336540.000067] XFS (md1): xfs_log_force: error 5 returned.
[336570.080069] XFS (md1): xfs_log_force: error 5 returned.
[336600.160082] XFS (md1): xfs_log_force: error 5 returned.

So this time, I may have lost my entire raid array. I'm going to attempt to
reboot, or re-assemble the array at some point, probably tonight, to see
if my array is hosed or not.

-- 
Thomas Fjellstrom
thomas@fjellstrom.ca

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2011-09-23  1:41 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
     [not found] <201109162002.13801.thomas@fjellstrom.ca>
2011-09-19  4:18 ` mvsas errors in 3.0 Thomas Fjellstrom
2011-09-23  1:40   ` mvsas errors in 3.0, URGENT Thomas Fjellstrom

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox