* READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
@ 2012-01-25 1:57 Kevin Shanahan
2012-01-25 5:22 ` Nandigama, Nagalakshmi
0 siblings, 1 reply; 5+ messages in thread
From: Kevin Shanahan @ 2012-01-25 1:57 UTC (permalink / raw)
To: linux-scsi
[-- Attachment #1: Type: text/plain, Size: 7791 bytes --]
Hi,
I wonder if someone can tell me what's going on with this new SAS
controller. I swapped out my old Marvell based controller for a new
Intel RS25GB008 and it seems that it never detects all the disks
correctly (there are 4 attached to this controller).
Trying to pull out the relevant bits of dmesg (full version attached):
[ 4.197386] mpt2sas version 10.100.00.00 loaded
[ 4.197501] scsi2 : Fusion MPT SAS Host
[ 4.197825] mpt2sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.197835] mpt2sas 0000:01:00.0: setting latency timer to 64
[ 4.197840] mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (8146696 kB)
[ 4.197933] mpt2sas 0000:01:00.0: irq 47 for MSI/MSI-X
[ 4.197938] mpt2sas 0000:01:00.0: irq 48 for MSI/MSI-X
[ 4.197943] mpt2sas 0000:01:00.0: irq 49 for MSI/MSI-X
[ 4.197948] mpt2sas 0000:01:00.0: irq 50 for MSI/MSI-X
[ 4.197981] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 47
[ 4.197983] mpt2sas0-msix1: PCI-MSI-X enabled: IRQ 48
[ 4.197984] mpt2sas0-msix2: PCI-MSI-X enabled: IRQ 49
[ 4.197986] mpt2sas0-msix3: PCI-MSI-X enabled: IRQ 50
[ 4.197987] mpt2sas0: iomem(0x00000000dfef0000), mapped(0xffffc900122e0000), size(65536)
[ 4.197989] mpt2sas0: ioport(0x000000000000de00), size(256)
[ 4.440008] mpt2sas0: sending message unit reset !!
[ 4.446683] mpt2sas0: message unit reset: SUCCESS
[ 4.590327] mpt2sas0: Allocated physical memory: size(11195 kB)
[ 4.590330] mpt2sas0: Current Controller Queue Depth(4859), Max Controller Queue Depth(5120)
[ 4.590332] mpt2sas0: Scatter Gather Elements per IO(128)
[ 4.790353] mpt2sas0: LSISAS2308: FWVersion(09.00.00.00), ChipRevision(0x01), BiosVersion(07.17.03.00)
[ 4.790356] mpt2sas0: Intel(R) RAID Controller RS25GB008
[ 4.790358] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ)
[ 4.790423] mpt2sas0: sending port enable !!
[ 4.792873] mpt2sas0: host_add: handle(0x0001), sas_addr(0x500605b003f34c80), phys(8)
[ 4.803344] mpt2sas0: port enable: SUCCESS
[ 4.814391] scsi 2:0:0:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.814397] scsi 2:0:0:0: SATA: handle(0x0009), sas_addr(0x4433221100000000), phy(0), device_name(0x4ee250019f620672)
[ 4.814400] scsi 2:0:0:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(0)
[ 4.814489] scsi 2:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.814498] scsi 2:0:0:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.820459] sd 2:0:0:0: [sdc] physical block alignment offset: 4096
[ 4.820465] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.820468] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 4.829459] scsi 2:0:1:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.829465] scsi 2:0:1:0: SATA: handle(0x000a), sas_addr(0x4433221101000000), phy(1), device_name(0x4ee250010e9c0673)
[ 4.829468] scsi 2:0:1:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(1)
[ 4.829546] scsi 2:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.829551] scsi 2:0:1:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.837538] sd 2:0:1:0: [sdd] physical block alignment offset: 4096
[ 4.837543] sd 2:0:1:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.837545] sd 2:0:1:0: [sdd] 4096-byte physical blocks
[ 4.844069] scsi 2:0:2:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.844075] scsi 2:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221102000000), phy(2), device_name(0x4ee25001c81a5bc7)
[ 4.844078] scsi 2:0:2:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(2)
[ 4.844153] scsi 2:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.844158] scsi 2:0:2:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.851179] sd 2:0:2:0: [sde] physical block alignment offset: 4096
[ 4.851184] sd 2:0:2:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.851186] sd 2:0:2:0: [sde] 4096-byte physical blocks
[ 4.851459] sd 2:0:0:0: [sdc] Write Protect is off
[ 4.851463] sd 2:0:0:0: [sdc] Mode Sense: 7f 00 00 08
[ 4.857728] scsi 2:0:3:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.857734] scsi 2:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221103000000), phy(3), device_name(0x4ee250010d1e0673)
[ 4.857737] scsi 2:0:3:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(3)
[ 4.857809] scsi 2:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.857814] scsi 2:0:3:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.858145] port-2:0: remove: sas_addr(0x4433221100000000)
[ 4.858154] port-2:0: remove: sas_addr(0x4433221100000000), phy(0)
[ 4.862435] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.862589] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.862592] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862594] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862623] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.862626] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862628] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862655] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.862902] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863127] sdc: detected capacity change from 3000592982016 to 0
[ 4.863199] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.863201] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863203] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863222] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.863223] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863226] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863251] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.863477] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863702] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 4.864690] sd 2:0:3:0: [sdf] physical block alignment offset: 4096
[ 4.864695] sd 2:0:3:0: [sdf] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.864698] sd 2:0:3:0: [sdf] 4096-byte physical blocks
[ 4.876736] sd 2:0:1:0: [sdd] Write Protect is off
[ 4.876740] sd 2:0:1:0: [sdd] Mode Sense: 7f 00 00 08
[ 4.885584] sd 2:0:2:0: [sde] Write Protect is off
[ 4.885588] sd 2:0:2:0: [sde] Mode Sense: 7f 00 00 08
[ 4.891538] sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.897125] sd 2:0:3:0: [sdf] Write Protect is off
[ 4.897129] sd 2:0:3:0: [sdf] Mode Sense: 7f 00 00 08
[ 4.900113] sd 2:0:2:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.910240] sd 2:0:3:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.974155] sdf: sdf1
[ 4.975438] sdd: sdd1
[ 4.983617] sde: sde1
[ 5.026685] sd 2:0:3:0: [sdf] Attached SCSI disk
[ 5.032538] sd 2:0:1:0: [sdd] Attached SCSI disk
[ 5.039178] sd 2:0:2:0: [sde] Attached SCSI disk
[ 5.039528] mpt2sas0: removing handle(0x0009), sas_addr(0x4433221100000000)
[ 5.039532] mpt2sas0: failure at drivers/scsi/mpt2sas/mpt2sas_transport.c:705/mpt2sas_transport_port_add()!
Usually if I hot-unplug and re-plug the disk in question it will be
detected properly, but next reboot I have the same problem again.
Does anything there point towards a hardware/software problem? I
notice there's a newer RS25GB008 bios available, though I'll need to
source a UEFI board in order to install it.
Thanks,
Kevin.
[-- Attachment #2: mpt2sas.dmesg --]
[-- Type: text/plain, Size: 53052 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.1-1-ARCH (tobias@T-POWA-LX) (gcc version 4.6.2 20111223 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Jan 13 06:50:31 CET 2012
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=5515e1a5-fb53-4e28-984b-d242814b1aaf ro quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bdce0000 (usable)
[ 0.000000] BIOS-e820: 00000000bdce0000 - 00000000bdce3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bdce3000 - 00000000bdcf0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bdcf0000 - 00000000bdd00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000240000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.4 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. G41MT-S2P/G41MT-S2P, BIOS F3 05/30/2011
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x240000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-through
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 0C0000000 mask FC0000000 uncachable
[ 0.000000] 2 base 0BE000000 mask FFE000000 uncachable
[ 0.000000] 3 base 0BDE00000 mask FFFE00000 uncachable
[ 0.000000] 4 base 100000000 mask F00000000 write-back
[ 0.000000] 5 base 200000000 mask FC0000000 write-back
[ 0.000000] 6 base 0BDD00000 mask FFFF00000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000bdd00000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xbdce0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000f5210] f5210
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[ 0.000000] init_memory_mapping: 0000000000000000-00000000bdce0000
[ 0.000000] 0000000000 - 00bdc00000 page 2M
[ 0.000000] 00bdc00000 - 00bdce0000 page 4k
[ 0.000000] kernel direct mapping tables up to bdce0000 @ 1fffb000-20000000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000240000000
[ 0.000000] 0100000000 - 0240000000 page 2M
[ 0.000000] kernel direct mapping tables up to 240000000 @ bdcd6000-bdce0000
[ 0.000000] RAMDISK: 37896000 - 37c43000
[ 0.000000] ACPI: RSDP 00000000000f6c70 00014 (v00 GBT )
[ 0.000000] ACPI: RSDT 00000000bdce3040 0003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: FACP 00000000bdce30c0 00074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: DSDT 00000000bdce3180 04195 (v01 GBT GBTUACPI 00001000 MSFT 0100000C)
[ 0.000000] ACPI: FACS 00000000bdce0000 00040
[ 0.000000] ACPI: HPET 00000000bdce7480 00038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
[ 0.000000] ACPI: MCFG 00000000bdce7500 0003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: TAMG 00000000bdce7540 06352 (v01 GBT GBT B0 5455312E BG?? 00020101)
[ 0.000000] ACPI: APIC 00000000bdce7380 00084 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: SSDT 00000000bdcee1e0 003AB (v01 PmRef CpuPm 00003000 INTL 20040311)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000240000000
[ 0.000000] Initmem setup node 0 0000000000000000-0000000240000000
[ 0.000000] NODE_DATA [000000023fffb000 - 000000023fffffff]
[ 0.000000] [ffffea0000000000-ffffea0008ffffff] PMD -> [ffff880237600000-ffff88023f5fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00240000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x000bdce0
[ 0.000000] 0: 0x00100000 -> 0x00240000
[ 0.000000] On node 0 totalpages: 2088046
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3913 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 16320 pages used for memmap
[ 0.000000] DMA32 zone: 757024 pages, LIFO batch:31
[ 0.000000] Normal zone: 20480 pages used for memmap
[ 0.000000] Normal zone: 1290240 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bdce0000 - 00000000bdce3000
[ 0.000000] PM: Registered nosave memory: 00000000bdce3000 - 00000000bdcf0000
[ 0.000000] PM: Registered nosave memory: 00000000bdcf0000 - 00000000bdd00000
[ 0.000000] PM: Registered nosave memory: 00000000bdd00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at bdd00000 (gap: bdd00000:22300000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88023fc00000 s82048 r8192 d24448 u524288
[ 0.000000] pcpu-alloc: s82048 r8192 d24448 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2051177
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=5515e1a5-fb53-4e28-984b-d242814b1aaf ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 8139660k/9437184k available (4279k kernel code, 1085000k absent, 212524k reserved, 4601k data, 728k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:4352 nr_irqs:712 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 67108864 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2666.967 MHz processor.
[ 0.003337] Calibrating delay loop (skipped), value calculated using timer frequency.. 5336.18 BogoMIPS (lpj=8889890)
[ 0.003340] pid_max: default: 32768 minimum: 301
[ 0.003362] Security Framework initialized
[ 0.003367] AppArmor: AppArmor disabled by boot time parameter
[ 0.007195] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.010429] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.011915] Mount-cache hash table entries: 256
[ 0.012048] Initializing cgroup subsys cpuacct
[ 0.012054] Initializing cgroup subsys memory
[ 0.012061] Initializing cgroup subsys devices
[ 0.012063] Initializing cgroup subsys freezer
[ 0.012064] Initializing cgroup subsys net_cls
[ 0.012066] Initializing cgroup subsys blkio
[ 0.012097] CPU: Physical Processor ID: 0
[ 0.012098] CPU: Processor Core ID: 0
[ 0.012100] mce: CPU supports 6 MCE banks
[ 0.012107] CPU0: Thermal monitoring enabled (TM2)
[ 0.012111] using mwait in idle threads.
[ 0.013188] ACPI: Core revision 20110623
[ 0.015356] ftrace: allocating 16773 entries in 66 pages
[ 0.017052] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.051280] CPU0: Intel(R) Core(TM)2 Quad CPU Q9450 @ 2.66GHz stepping 07
[ 0.053330] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.053330] ... version: 2
[ 0.053330] ... bit width: 40
[ 0.053330] ... generic registers: 2
[ 0.053330] ... value mask: 000000ffffffffff
[ 0.053330] ... max period: 000000007fffffff
[ 0.053330] ... fixed-purpose events: 3
[ 0.053330] ... event mask: 0000000700000003
[ 0.070120] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.096674] Booting Node 0, Processors #1
[ 0.096677] smpboot cpu 1: start_ip = 99000
[ 0.193348] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.213349] #2
[ 0.213351] smpboot cpu 2: start_ip = 99000
[ 0.309997] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.329996] #3 Ok.
[ 0.329998] smpboot cpu 3: start_ip = 99000
[ 0.426656] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.433310] Brought up 4 CPUs
[ 0.433313] Total of 4 processors activated (21342.39 BogoMIPS).
[ 0.436801] devtmpfs: initialized
[ 0.440441] PM: Registering ACPI NVS region at bdce0000 (12288 bytes)
[ 0.440661] print_constraints: dummy:
[ 0.440702] NET: Registered protocol family 16
[ 0.440802] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.440805] ACPI: bus type pci registered
[ 0.440862] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.440864] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.477147] PCI: Using configuration type 1 for base access
[ 0.477645] bio: create slab <bio-0> at 0
[ 0.477645] ACPI: Added _OSI(Module Device)
[ 0.477645] ACPI: Added _OSI(Processor Device)
[ 0.477645] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.477645] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.477645] ACPI: EC: Look up EC in DSDT
[ 0.480607] ACPI Warning: Incorrect checksum in table [TAMG] - 0xE7, should be 0xE6 (20110623/tbutils-314)
[ 0.480700] ACPI: SSDT 00000000bdced900 0022A (v01 PmRef Cpu0Ist 00003000 INTL 20040311)
[ 0.480834] ACPI: Dynamic OEM Table Load:
[ 0.480837] ACPI: SSDT (null) 0022A (v01 PmRef Cpu0Ist 00003000 INTL 20040311)
[ 0.480921] ACPI: SSDT 00000000bdceddc0 00152 (v01 PmRef Cpu1Ist 00003000 INTL 20040311)
[ 0.481053] ACPI: Dynamic OEM Table Load:
[ 0.481056] ACPI: SSDT (null) 00152 (v01 PmRef Cpu1Ist 00003000 INTL 20040311)
[ 0.481143] ACPI: SSDT 00000000bdcedf20 00152 (v01 PmRef Cpu2Ist 00003000 INTL 20040311)
[ 0.481272] ACPI: Dynamic OEM Table Load:
[ 0.481275] ACPI: SSDT (null) 00152 (v01 PmRef Cpu2Ist 00003000 INTL 20040311)
[ 0.481360] ACPI: SSDT 00000000bdcee080 00152 (v01 PmRef Cpu3Ist 00003000 INTL 20040311)
[ 0.481490] ACPI: Dynamic OEM Table Load:
[ 0.481492] ACPI: SSDT (null) 00152 (v01 PmRef Cpu3Ist 00003000 INTL 20040311)
[ 0.481584] ACPI: Interpreter enabled
[ 0.481587] ACPI: (supports S0 S3 S4 S5)
[ 0.481600] ACPI: Using IOAPIC for interrupt routing
[ 0.484506] ACPI: No dock devices found.
[ 0.484508] HEST: Table not found.
[ 0.484511] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.484550] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.484640] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
[ 0.484642] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
[ 0.484644] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.484646] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
[ 0.484648] pci_root PNP0A03:00: host bridge window [mem 0xbdd00000-0xfebfffff]
[ 0.484657] pci 0000:00:00.0: [8086:2e30] type 0 class 0x000600
[ 0.484688] pci 0000:00:01.0: [8086:2e31] type 1 class 0x000604
[ 0.484711] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.484713] pci 0000:00:01.0: PME# disabled
[ 0.484725] pci 0000:00:02.0: [8086:2e32] type 0 class 0x000300
[ 0.484734] pci 0000:00:02.0: reg 10: [mem 0xdf400000-0xdf7fffff 64bit]
[ 0.484740] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.484745] pci 0000:00:02.0: reg 20: [io 0xff00-0xff07]
[ 0.484792] pci 0000:00:1b.0: [8086:27d8] type 0 class 0x000403
[ 0.484804] pci 0000:00:1b.0: reg 10: [mem 0xdfff8000-0xdfffbfff 64bit]
[ 0.484849] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.484852] pci 0000:00:1b.0: PME# disabled
[ 0.484868] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[ 0.484913] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.484916] pci 0000:00:1c.0: PME# disabled
[ 0.484934] pci 0000:00:1c.2: [8086:27d4] type 1 class 0x000604
[ 0.484978] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.484982] pci 0000:00:1c.2: PME# disabled
[ 0.485002] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[ 0.485035] pci 0000:00:1d.0: reg 20: [io 0xfe00-0xfe1f]
[ 0.485059] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[ 0.485092] pci 0000:00:1d.1: reg 20: [io 0xfd00-0xfd1f]
[ 0.485116] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[ 0.485150] pci 0000:00:1d.2: reg 20: [io 0xfc00-0xfc1f]
[ 0.485173] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[ 0.485207] pci 0000:00:1d.3: reg 20: [io 0xfb00-0xfb1f]
[ 0.485237] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[ 0.485251] pci 0000:00:1d.7: reg 10: [mem 0xdffff000-0xdffff3ff]
[ 0.485316] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 0.485362] pci 0000:00:1f.0: [8086:27b8] type 0 class 0x000601
[ 0.485432] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f)
[ 0.485436] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f)
[ 0.485465] pci 0000:00:1f.2: [8086:27c0] type 0 class 0x000101
[ 0.485476] pci 0000:00:1f.2: reg 10: [io 0x0000-0x0007]
[ 0.485483] pci 0000:00:1f.2: reg 14: [io 0x0000-0x0003]
[ 0.485489] pci 0000:00:1f.2: reg 18: [io 0x0000-0x0007]
[ 0.485496] pci 0000:00:1f.2: reg 1c: [io 0x0000-0x0003]
[ 0.485503] pci 0000:00:1f.2: reg 20: [io 0xf800-0xf80f]
[ 0.485526] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.485529] pci 0000:00:1f.2: PME# disabled
[ 0.485541] pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05
[ 0.485585] pci 0000:00:1f.3: reg 20: [io 0x0500-0x051f]
[ 0.485640] pci 0000:01:00.0: [1000:0087] type 0 class 0x000107
[ 0.485650] pci 0000:01:00.0: reg 10: [io 0xde00-0xdeff]
[ 0.485661] pci 0000:01:00.0: reg 14: [mem 0xdfef0000-0xdfefffff 64bit]
[ 0.485672] pci 0000:01:00.0: reg 1c: [mem 0xdfe80000-0xdfebffff 64bit]
[ 0.485685] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000fffff pref]
[ 0.485707] pci 0000:01:00.0: supports D1 D2
[ 0.485726] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.485728] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.485731] pci 0000:00:01.0: bridge window [mem 0xdfd00000-0xdfefffff]
[ 0.485789] pci 0000:02:00.0: [8086:10d3] type 0 class 0x000200
[ 0.485811] pci 0000:02:00.0: reg 10: [mem 0xdfcc0000-0xdfcdffff]
[ 0.485827] pci 0000:02:00.0: reg 14: [mem 0xdfc00000-0xdfc7ffff]
[ 0.485843] pci 0000:02:00.0: reg 18: [io 0xcf00-0xcf1f]
[ 0.485860] pci 0000:02:00.0: reg 1c: [mem 0xdfcfc000-0xdfcfffff]
[ 0.485905] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0003ffff pref]
[ 0.485954] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.485960] pci 0000:02:00.0: PME# disabled
[ 0.485998] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.486001] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
[ 0.486004] pci 0000:00:1c.0: bridge window [mem 0xdfc00000-0xdfcfffff]
[ 0.486055] pci 0000:03:00.0: [1969:1073] type 0 class 0x000200
[ 0.486076] pci 0000:03:00.0: reg 10: [mem 0xdfbc0000-0xdfbfffff 64bit]
[ 0.486087] pci 0000:03:00.0: reg 18: [io 0xbf00-0xbf7f]
[ 0.486157] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.486162] pci 0000:03:00.0: PME# disabled
[ 0.486188] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 0.486191] pci 0000:00:1c.2: bridge window [io 0xb000-0xbfff]
[ 0.486194] pci 0000:00:1c.2: bridge window [mem 0xdfb00000-0xdfbfffff]
[ 0.486248] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 0.486256] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.486258] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.486260] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.486262] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.486264] pci 0000:00:1e.0: bridge window [mem 0xbdd00000-0xfebfffff] (subtractive decode)
[ 0.486279] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.486353] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.486377] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[ 0.486402] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.486443] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.486446] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.486448] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.491471] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.491508] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.491549] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.491587] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.491623] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.491659] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.491695] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.491732] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.491818] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.491818] vgaarb: loaded
[ 0.491818] vgaarb: bridge control possible 0000:00:02.0
[ 0.491818] PCI: Using ACPI for IRQ routing
[ 0.496929] PCI: pci_cache_line_size set to 64 bytes
[ 0.496983] reserve RAM buffer: 000000000009e400 - 000000000009ffff
[ 0.496985] reserve RAM buffer: 00000000bdce0000 - 00000000bfffffff
[ 0.497070] NetLabel: Initializing
[ 0.497071] NetLabel: domain hash size = 128
[ 0.497073] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.497083] NetLabel: unlabeled traffic allowed by default
[ 0.497096] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.497099] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.497103] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.513371] Switching to clocksource hpet
[ 0.518851] pnp: PnP ACPI init
[ 0.518863] ACPI: bus type pnp registered
[ 0.518923] pnp 00:00: [bus 00-ff]
[ 0.518925] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.518927] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.518928] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.518930] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.518932] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[ 0.518934] pnp 00:00: [mem 0xbdd00000-0xfebfffff window]
[ 0.518975] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.519018] pnp 00:01: [io 0x0010-0x001f]
[ 0.519020] pnp 00:01: [io 0x0022-0x003f]
[ 0.519021] pnp 00:01: [io 0x0044-0x005f]
[ 0.519023] pnp 00:01: [io 0x0062-0x0063]
[ 0.519024] pnp 00:01: [io 0x0065-0x006f]
[ 0.519026] pnp 00:01: [io 0x0074-0x007f]
[ 0.519027] pnp 00:01: [io 0x0091-0x0093]
[ 0.519029] pnp 00:01: [io 0x00a2-0x00bf]
[ 0.519030] pnp 00:01: [io 0x00e0-0x00ef]
[ 0.519032] pnp 00:01: [io 0x04d0-0x04d1]
[ 0.519033] pnp 00:01: [io 0x0290-0x029f]
[ 0.519035] pnp 00:01: [io 0x0800-0x087f]
[ 0.519036] pnp 00:01: [io 0x0290-0x0294]
[ 0.519038] pnp 00:01: [io 0x0880-0x088f]
[ 0.519084] system 00:01: [io 0x04d0-0x04d1] has been reserved
[ 0.519086] system 00:01: [io 0x0290-0x029f] has been reserved
[ 0.519088] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.519090] system 00:01: [io 0x0290-0x0294] has been reserved
[ 0.519092] system 00:01: [io 0x0880-0x088f] has been reserved
[ 0.519095] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.519105] pnp 00:02: [dma 4]
[ 0.519106] pnp 00:02: [io 0x0000-0x000f]
[ 0.519108] pnp 00:02: [io 0x0080-0x0090]
[ 0.519109] pnp 00:02: [io 0x0094-0x009f]
[ 0.519112] pnp 00:02: [io 0x00c0-0x00df]
[ 0.519135] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.519171] pnp 00:03: [irq 0 disabled]
[ 0.519179] pnp 00:03: [irq 8]
[ 0.519180] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.519206] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.519226] pnp 00:04: [io 0x0070-0x0073]
[ 0.519252] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.519259] pnp 00:05: [io 0x0061]
[ 0.519284] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.519291] pnp 00:06: [io 0x00f0-0x00ff]
[ 0.519296] pnp 00:06: [irq 13]
[ 0.519321] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.519495] pnp 00:07: [io 0x03f8-0x03ff]
[ 0.519500] pnp 00:07: [irq 4]
[ 0.519551] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.519682] pnp 00:08: [io 0x0378-0x037f]
[ 0.519687] pnp 00:08: [irq 7]
[ 0.519730] pnp 00:08: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.519811] pnp 00:09: [io 0x0400-0x047f]
[ 0.519848] system 00:09: [io 0x0400-0x047f] has been reserved
[ 0.519850] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.519978] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[ 0.520038] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.520041] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.520154] pnp 00:0b: [mem 0x000d7000-0x000d7fff]
[ 0.520156] pnp 00:0b: [mem 0x000f0000-0x000f7fff]
[ 0.520157] pnp 00:0b: [mem 0x000f8000-0x000fbfff]
[ 0.520159] pnp 00:0b: [mem 0x000fc000-0x000fffff]
[ 0.520160] pnp 00:0b: [mem 0xbdce0000-0xbdceffff]
[ 0.520162] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[ 0.520163] pnp 00:0b: [mem 0x00100000-0xbdcdffff]
[ 0.520165] pnp 00:0b: [mem 0xbdcf0000-0xbdcfffff]
[ 0.520167] pnp 00:0b: [mem 0xfec00000-0xfec00fff]
[ 0.520168] pnp 00:0b: [mem 0xfed13000-0xfed1dfff]
[ 0.520170] pnp 00:0b: [mem 0xfed20000-0xfed8ffff]
[ 0.520171] pnp 00:0b: [mem 0xfee00000-0xfee00fff]
[ 0.520173] pnp 00:0b: [mem 0xffb00000-0xffb7ffff]
[ 0.520174] pnp 00:0b: [mem 0xfff00000-0xffffffff]
[ 0.520176] pnp 00:0b: [mem 0x000e0000-0x000effff]
[ 0.520191] pnp 00:0b: disabling [mem 0x000d7000-0x000d7fff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520194] pnp 00:0b: disabling [mem 0x000f0000-0x000f7fff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520196] pnp 00:0b: disabling [mem 0x000f8000-0x000fbfff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520199] pnp 00:0b: disabling [mem 0x000fc000-0x000fffff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520202] pnp 00:0b: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520205] pnp 00:0b: disabling [mem 0x000e0000-0x000effff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.520245] system 00:0b: [mem 0xbdce0000-0xbdceffff] could not be reserved
[ 0.520247] system 00:0b: [mem 0x00100000-0xbdcdffff] could not be reserved
[ 0.520250] system 00:0b: [mem 0xbdcf0000-0xbdcfffff] has been reserved
[ 0.520252] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.520254] system 00:0b: [mem 0xfed13000-0xfed1dfff] has been reserved
[ 0.520256] system 00:0b: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.520258] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.520261] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.520263] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.520265] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.520282] pnp 00:0c: [mem 0xffb80000-0xffbfffff]
[ 0.520314] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.520319] pnp: PnP ACPI: found 13 devices
[ 0.520320] ACPI: ACPI bus type pnp unregistered
[ 0.528892] PCI: max bus depth: 1 pci_try_num: 2
[ 0.528917] pci 0000:00:01.0: BAR 15: assigned [mem 0xbdd00000-0xbddfffff pref]
[ 0.528921] pci 0000:00:1c.0: BAR 15: assigned [mem 0xbde00000-0xbdefffff pref]
[ 0.528924] pci 0000:00:1c.2: BAR 15: assigned [mem 0xbdf00000-0xbe0fffff 64bit pref]
[ 0.528928] pci 0000:00:1c.0: BAR 15: assigned [mem 0xbe100000-0xbe3fffff pref]
[ 0.528931] pci 0000:01:00.0: BAR 6: assigned [mem 0xbdd00000-0xbddfffff pref]
[ 0.528933] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.528935] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.528938] pci 0000:00:01.0: bridge window [mem 0xdfd00000-0xdfefffff]
[ 0.528940] pci 0000:00:01.0: bridge window [mem 0xbdd00000-0xbddfffff pref]
[ 0.528944] pci 0000:02:00.0: BAR 6: assigned [mem 0xbe100000-0xbe13ffff pref]
[ 0.528946] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.528948] pci 0000:00:1c.0: bridge window [io 0xc000-0xcfff]
[ 0.528952] pci 0000:00:1c.0: bridge window [mem 0xdfc00000-0xdfcfffff]
[ 0.528955] pci 0000:00:1c.0: bridge window [mem 0xbe100000-0xbe3fffff pref]
[ 0.528960] pci 0000:00:1c.2: PCI bridge to [bus 03-03]
[ 0.528963] pci 0000:00:1c.2: bridge window [io 0xb000-0xbfff]
[ 0.528967] pci 0000:00:1c.2: bridge window [mem 0xdfb00000-0xdfbfffff]
[ 0.528970] pci 0000:00:1c.2: bridge window [mem 0xbdf00000-0xbe0fffff 64bit pref]
[ 0.528975] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 0.528991] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.528995] pci 0000:00:01.0: setting latency timer to 64
[ 0.529000] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.529003] pci 0000:00:1c.0: setting latency timer to 64
[ 0.529010] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.529014] pci 0000:00:1c.2: setting latency timer to 64
[ 0.529019] pci 0000:00:1e.0: setting latency timer to 64
[ 0.529022] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.529024] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.529026] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.529028] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.529030] pci_bus 0000:00: resource 8 [mem 0xbdd00000-0xfebfffff]
[ 0.529032] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.529034] pci_bus 0000:01: resource 1 [mem 0xdfd00000-0xdfefffff]
[ 0.529036] pci_bus 0000:01: resource 2 [mem 0xbdd00000-0xbddfffff pref]
[ 0.529037] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 0.529039] pci_bus 0000:02: resource 1 [mem 0xdfc00000-0xdfcfffff]
[ 0.529041] pci_bus 0000:02: resource 2 [mem 0xbe100000-0xbe3fffff pref]
[ 0.529043] pci_bus 0000:03: resource 0 [io 0xb000-0xbfff]
[ 0.529045] pci_bus 0000:03: resource 1 [mem 0xdfb00000-0xdfbfffff]
[ 0.529047] pci_bus 0000:03: resource 2 [mem 0xbdf00000-0xbe0fffff 64bit pref]
[ 0.529049] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 0.529051] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 0.529052] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.529054] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.529056] pci_bus 0000:04: resource 8 [mem 0xbdd00000-0xfebfffff]
[ 0.529084] NET: Registered protocol family 2
[ 0.529267] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.530332] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.533166] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.533568] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.533571] TCP reno registered
[ 0.533585] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.533641] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.533785] NET: Registered protocol family 1
[ 0.533802] pci 0000:00:02.0: Boot video device
[ 0.546711] PCI: CLS 4 bytes, default 64
[ 0.546773] Unpacking initramfs...
[ 0.594006] Freeing initrd memory: 3764k freed
[ 0.594812] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.594815] Placing 64MB software IO TLB between ffff8800b9cd6000 - ffff8800bdcd6000
[ 0.594817] software IO TLB at phys 0xb9cd6000 - 0xbdcd6000
[ 0.595318] audit: initializing netlink socket (disabled)
[ 0.595328] type=2000 audit(1327395304.593:1): initialized
[ 0.615299] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.654338] VFS: Disk quotas dquot_6.5.2
[ 0.654393] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.654472] msgmni has been set to 15905
[ 0.654702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.654757] io scheduler noop registered
[ 0.654758] io scheduler deadline registered
[ 0.654791] io scheduler cfq registered (default)
[ 0.654879] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.654904] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.654944] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.654974] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.655024] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.655054] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[ 0.655170] vesafb: mode is 1920x1440x32, linelength=7680, pages=0
[ 0.655171] vesafb: scrolling: redraw
[ 0.655173] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.656770] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90011800000, using 10816k, total 10816k
[ 0.723942] Console: switching to colour frame buffer device 240x90
[ 0.790914] fb0: VESA VGA frame buffer device
[ 0.790925] intel_idle: MWAIT substates: 0x20
[ 0.790927] intel_idle: does not run on family 6 model 23
[ 0.790950] ERST: Table is not found!
[ 0.790952] GHES: HEST is not enabled!
[ 0.791026] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.811509] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.020588] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.080192] Linux agpgart interface v0.103
[ 1.080270] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.113901] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 1.113902] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 1.363433] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.363572] mousedev: PS/2 mouse device common for all mice
[ 1.363642] rtc_cmos 00:04: RTC can wake from S4
[ 1.363766] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.363787] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 1.363795] cpuidle: using governor ladder
[ 1.363797] cpuidle: using governor menu
[ 1.363990] TCP cubic registered
[ 1.363993] NET: Registered protocol family 17
[ 1.364000] Registering the dns_resolver key type
[ 1.364168] PM: Hibernation image not present or could not be loaded.
[ 1.364172] registered taskstats version 1
[ 1.383140] rtc_cmos 00:04: setting system clock to 2012-01-24 08:55:05 UTC (1327395305)
[ 1.383178] Initializing network drop monitor service
[ 1.384355] Freeing unused kernel memory: 728k freed
[ 1.384478] Write protecting the kernel read-only data: 8192k
[ 1.389776] Freeing unused kernel memory: 1848k freed
[ 1.392101] Freeing unused kernel memory: 696k freed
[ 1.399139] udevd[48]: starting version 175
[ 1.422953] usbcore: registered new interface driver usbfs
[ 1.422976] usbcore: registered new interface driver hub
[ 1.427438] usbcore: registered new device driver usb
[ 1.432232] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.433277] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.433301] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.433304] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.433324] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.433360] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 1.437256] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported
[ 1.437265] SCSI subsystem initialized
[ 1.437272] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdffff000
[ 1.441152] libata version 3.00 loaded.
[ 1.450053] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.450216] hub 1-0:1.0: USB hub found
[ 1.450220] hub 1-0:1.0: 8 ports detected
[ 1.450310] ata_piix 0000:00:1f.2: version 2.13
[ 1.450337] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.450342] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.450378] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.450666] scsi0 : ata_piix
[ 1.450743] scsi1 : ata_piix
[ 1.451099] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf800 irq 14
[ 1.451101] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf808 irq 15
[ 1.451638] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.451672] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.451679] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.451682] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.451690] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.451713] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00
[ 1.451840] hub 2-0:1.0: USB hub found
[ 1.451843] hub 2-0:1.0: 2 ports detected
[ 1.451901] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.451906] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.451908] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.451914] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.451942] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00
[ 1.452049] hub 3-0:1.0: USB hub found
[ 1.452053] hub 3-0:1.0: 2 ports detected
[ 1.452106] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.452110] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.452113] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.452119] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.452145] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00
[ 1.452261] hub 4-0:1.0: USB hub found
[ 1.452268] hub 4-0:1.0: 2 ports detected
[ 1.452330] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 1.452334] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.452337] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.452343] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.452369] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00
[ 1.452483] hub 5-0:1.0: USB hub found
[ 1.452486] hub 5-0:1.0: 2 ports detected
[ 1.596683] Refined TSC clocksource calibration: 2666.615 MHz.
[ 1.596688] Switching to clocksource tsc
[ 1.611715] ata2.00: ATA-6: WDC WD2500JD-00GBB0, 02.05D02, max UDMA/100
[ 1.611719] ata2.00: 488397168 sectors, multi 16: LBA48
[ 1.611723] ata2.00: applying bridge limits
[ 1.619509] ata1.00: ATA-7: WDC WD2500YS-01SHB0, 20.06C03, max UDMA/133
[ 1.619512] ata1.00: 490234752 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.624574] ata1.00: configured for UDMA/133
[ 1.624682] scsi 0:0:0:0: Direct-Access ATA WDC WD2500YS-01S 20.0 PQ: 0 ANSI: 5
[ 1.625055] ata2.00: configured for UDMA/100
[ 1.625176] scsi 1:0:0:0: Direct-Access ATA WDC WD2500JD-00G 02.0 PQ: 0 ANSI: 5
[ 1.629489] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB)
[ 1.629534] sd 0:0:0:0: [sda] Write Protect is off
[ 1.629537] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.629558] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.629564] sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 1.629616] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.629620] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.629644] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.633360] sda: sda1 sda2 sda3 sda4
[ 1.633683] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.648677] sdb: sdb1 sdb2 sdb3 sdb4
[ 1.649076] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.912099] md: md0 stopped.
[ 1.913118] md: bind<sdb1>
[ 1.913312] md: bind<sda1>
[ 1.915357] md: raid1 personality registered for level 1
[ 1.915579] bio: create slab <bio-1> at 1
[ 1.915651] md/raid1:md0: active with 2 out of 2 mirrors
[ 1.915798] created bitmap (1 pages) for device md0
[ 1.915955] md0: bitmap initialized from disk: read 1/1 pages, set 0 of 3 bits
[ 1.933489] md0: detected capacity change from 0 to 157274112
[ 1.933994] md0: unknown partition table
[ 1.967547] md: md1 stopped.
[ 1.968573] md: bind<sdb2>
[ 1.968769] md: bind<sda2>
[ 1.969759] md/raid1:md1: active with 2 out of 2 mirrors
[ 1.969909] created bitmap (1 pages) for device md1
[ 1.970057] md1: bitmap initialized from disk: read 1/1 pages, set 0 of 240 bits
[ 2.009440] md1: detected capacity change from 0 to 16105005056
[ 2.017601] md1: unknown partition table
[ 2.045471] md: md2 stopped.
[ 2.046787] md: bind<sdb3>
[ 2.046989] md: bind<sda3>
[ 2.047708] md/raid1:md2: active with 2 out of 2 mirrors
[ 2.047849] created bitmap (1 pages) for device md2
[ 2.047999] md2: bitmap initialized from disk: read 1/1 pages, set 0 of 32 bits
[ 2.065307] md2: detected capacity change from 0 to 2146422784
[ 2.072142] md2: unknown partition table
[ 2.073347] usb 5-2: new full-speed USB device number 2 using uhci_hcd
[ 2.090174] md: md3 stopped.
[ 2.091207] md: bind<sdb4>
[ 2.091443] md: bind<sda4>
[ 2.092181] md/raid1:md3: active with 2 out of 2 mirrors
[ 2.092313] created bitmap (2 pages) for device md3
[ 2.092486] md3: bitmap initialized from disk: read 1/1 pages, set 0 of 3452 bits
[ 2.145827] md3: detected capacity change from 0 to 231646216192
[ 2.147324] md3: unknown partition table
[ 2.150861] device-mapper: uevent: version 1.0.3
[ 2.151094] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 2.217455] hub 5-2:1.0: USB hub found
[ 2.219406] hub 5-2:1.0: 4 ports detected
[ 2.498403] usb 5-2.1: new low-speed USB device number 3 using uhci_hcd
[ 2.555934] EXT4-fs (md1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.906779] udevd[252]: starting version 178
[ 4.071694] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 4.097435] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.097497] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 4.097516] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 4.121316] intel_rng: FWH not detected
[ 4.139224] atl1c 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.139233] atl1c 0000:03:00.0: setting latency timer to 64
[ 4.146998] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k
[ 4.147000] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[ 4.147021] e1000e 0000:02:00.0: Disabling ASPM L0s
[ 4.147033] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.147050] e1000e 0000:02:00.0: setting latency timer to 64
[ 4.147239] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 4.147244] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 4.147249] e1000e 0000:02:00.0: irq 46 for MSI/MSI-X
[ 4.163553] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 4.163682] ACPI: Power Button [PWRB]
[ 4.163743] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 4.163808] ACPI: Power Button [PWRF]
[ 4.179084] IT8718 SuperIO detected.
[ 4.179331] parport_pc 00:08: reported by Plug and Play ACPI
[ 4.179370] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 4.186219] [drm] Initialized drm 1.1.0 20060810
[ 4.194334] leds_ss4200: no LED devices found
[ 4.197386] mpt2sas version 10.100.00.00 loaded
[ 4.197501] scsi2 : Fusion MPT SAS Host
[ 4.197825] mpt2sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.197835] mpt2sas 0000:01:00.0: setting latency timer to 64
[ 4.197840] mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (8146696 kB)
[ 4.197933] mpt2sas 0000:01:00.0: irq 47 for MSI/MSI-X
[ 4.197938] mpt2sas 0000:01:00.0: irq 48 for MSI/MSI-X
[ 4.197943] mpt2sas 0000:01:00.0: irq 49 for MSI/MSI-X
[ 4.197948] mpt2sas 0000:01:00.0: irq 50 for MSI/MSI-X
[ 4.197981] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 47
[ 4.197983] mpt2sas0-msix1: PCI-MSI-X enabled: IRQ 48
[ 4.197984] mpt2sas0-msix2: PCI-MSI-X enabled: IRQ 49
[ 4.197986] mpt2sas0-msix3: PCI-MSI-X enabled: IRQ 50
[ 4.197987] mpt2sas0: iomem(0x00000000dfef0000), mapped(0xffffc900122e0000), size(65536)
[ 4.197989] mpt2sas0: ioport(0x000000000000de00), size(256)
[ 4.209983] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 4.210176] agpgart-intel 0000:00:00.0: Intel G41 Chipset
[ 4.210301] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 4.212376] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[ 4.212735] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 4.244401] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.244405] i915 0000:00:02.0: setting latency timer to 64
[ 4.251606] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1b:21:d5:65:e3
[ 4.251609] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 4.251622] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: E46981-006
[ 4.253720] atl1c 0000:03:00.0: version 1.0.1.0-NAPI
[ 4.283580] mtrr: type mismatch for c0000000,10000000 old: write-back new: write-combining
[ 4.283582] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 4.283861] i915 0000:00:02.0: irq 51 for MSI/MSI-X
[ 4.283865] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.283866] [drm] Driver supports precise vblank timestamp query.
[ 4.283886] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.303700] ppdev: user-space parallel port driver
[ 4.329099] iTCO_vendor_support: vendor-support=0
[ 4.330082] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 4.330241] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[ 4.330367] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.407537] checking generic (c0000000 a90000) vs hw (c0000000 10000000)
[ 4.407540] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
[ 4.407564] Console: switching to colour dummy device 80x25
[ 4.408498] fbcon: inteldrmfb (fb0) is primary device
[ 4.440008] mpt2sas0: sending message unit reset !!
[ 4.446683] mpt2sas0: message unit reset: SUCCESS
[ 4.447175] Console: switching to colour frame buffer device 210x65
[ 4.487662] input: CHICONY USB NetVista Full Width Keyboard as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2.1/5-2.1:1.0/input/input3
[ 4.487753] generic-usb 0003:04B3:3025.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY USB NetVista Full Width Keyboard] on usb-0000:00:1d.3-2.1/input0
[ 4.487769] usbcore: registered new interface driver usbhid
[ 4.487770] usbhid: USB HID core driver
[ 4.491111] fb0: inteldrmfb frame buffer device
[ 4.491112] drm: registered panic notifier
[ 4.491160] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.590327] mpt2sas0: Allocated physical memory: size(11195 kB)
[ 4.590330] mpt2sas0: Current Controller Queue Depth(4859), Max Controller Queue Depth(5120)
[ 4.590332] mpt2sas0: Scatter Gather Elements per IO(128)
[ 4.790353] mpt2sas0: LSISAS2308: FWVersion(09.00.00.00), ChipRevision(0x01), BiosVersion(07.17.03.00)
[ 4.790356] mpt2sas0: Intel(R) RAID Controller RS25GB008
[ 4.790358] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ)
[ 4.790423] mpt2sas0: sending port enable !!
[ 4.792873] mpt2sas0: host_add: handle(0x0001), sas_addr(0x500605b003f34c80), phys(8)
[ 4.803344] mpt2sas0: port enable: SUCCESS
[ 4.814391] scsi 2:0:0:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.814397] scsi 2:0:0:0: SATA: handle(0x0009), sas_addr(0x4433221100000000), phy(0), device_name(0x4ee250019f620672)
[ 4.814400] scsi 2:0:0:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(0)
[ 4.814489] scsi 2:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.814498] scsi 2:0:0:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.820459] sd 2:0:0:0: [sdc] physical block alignment offset: 4096
[ 4.820465] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.820468] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 4.829459] scsi 2:0:1:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.829465] scsi 2:0:1:0: SATA: handle(0x000a), sas_addr(0x4433221101000000), phy(1), device_name(0x4ee250010e9c0673)
[ 4.829468] scsi 2:0:1:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(1)
[ 4.829546] scsi 2:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.829551] scsi 2:0:1:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.837538] sd 2:0:1:0: [sdd] physical block alignment offset: 4096
[ 4.837543] sd 2:0:1:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.837545] sd 2:0:1:0: [sdd] 4096-byte physical blocks
[ 4.844069] scsi 2:0:2:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.844075] scsi 2:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221102000000), phy(2), device_name(0x4ee25001c81a5bc7)
[ 4.844078] scsi 2:0:2:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(2)
[ 4.844153] scsi 2:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.844158] scsi 2:0:2:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.851179] sd 2:0:2:0: [sde] physical block alignment offset: 4096
[ 4.851184] sd 2:0:2:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.851186] sd 2:0:2:0: [sde] 4096-byte physical blocks
[ 4.851459] sd 2:0:0:0: [sdc] Write Protect is off
[ 4.851463] sd 2:0:0:0: [sdc] Mode Sense: 7f 00 00 08
[ 4.857728] scsi 2:0:3:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.857734] scsi 2:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221103000000), phy(3), device_name(0x4ee250010d1e0673)
[ 4.857737] scsi 2:0:3:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(3)
[ 4.857809] scsi 2:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.857814] scsi 2:0:3:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.858145] port-2:0: remove: sas_addr(0x4433221100000000)
[ 4.858154] port-2:0: remove: sas_addr(0x4433221100000000), phy(0)
[ 4.862435] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.862589] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.862592] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862594] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862623] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.862626] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862628] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862655] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.862902] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863127] sdc: detected capacity change from 3000592982016 to 0
[ 4.863199] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.863201] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863203] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863222] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.863223] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863226] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863251] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.863477] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863702] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 4.864690] sd 2:0:3:0: [sdf] physical block alignment offset: 4096
[ 4.864695] sd 2:0:3:0: [sdf] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.864698] sd 2:0:3:0: [sdf] 4096-byte physical blocks
[ 4.876736] sd 2:0:1:0: [sdd] Write Protect is off
[ 4.876740] sd 2:0:1:0: [sdd] Mode Sense: 7f 00 00 08
[ 4.885584] sd 2:0:2:0: [sde] Write Protect is off
[ 4.885588] sd 2:0:2:0: [sde] Mode Sense: 7f 00 00 08
[ 4.891538] sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.897125] sd 2:0:3:0: [sdf] Write Protect is off
[ 4.897129] sd 2:0:3:0: [sdf] Mode Sense: 7f 00 00 08
[ 4.900113] sd 2:0:2:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.910240] sd 2:0:3:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.974155] sdf: sdf1
[ 4.975438] sdd: sdd1
[ 4.983617] sde: sde1
[ 5.026685] sd 2:0:3:0: [sdf] Attached SCSI disk
[ 5.032538] sd 2:0:1:0: [sdd] Attached SCSI disk
[ 5.039178] sd 2:0:2:0: [sde] Attached SCSI disk
[ 5.039528] mpt2sas0: removing handle(0x0009), sas_addr(0x4433221100000000)
[ 5.039532] mpt2sas0: failure at drivers/scsi/mpt2sas/mpt2sas_transport.c:705/mpt2sas_transport_port_add()!
[ 5.121369] md: bind<sdf1>
[ 5.130454] md: bind<sdd1>
[ 5.132832] md: bind<sde1>
[ 35.097940] EXT4-fs (md1): re-mounted. Opts: (null)
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
2012-01-25 1:57 READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add Kevin Shanahan
@ 2012-01-25 5:22 ` Nandigama, Nagalakshmi
2012-01-25 8:07 ` Kevin Shanahan
0 siblings, 1 reply; 5+ messages in thread
From: Nandigama, Nagalakshmi @ 2012-01-25 5:22 UTC (permalink / raw)
To: Kevin Shanahan, linux-scsi@vger.kernel.org
[-- Attachment #1: Type: text/plain, Size: 8276 bytes --]
Kevin,
Request to apply the attached patch and test.
Regards,
Nagalakshmi
-----Original Message-----
From: linux-scsi-owner@vger.kernel.org [mailto:linux-scsi-owner@vger.kernel.org] On Behalf Of Kevin Shanahan
Sent: Wednesday, January 25, 2012 7:27 AM
To: linux-scsi@vger.kernel.org
Subject: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
Hi,
I wonder if someone can tell me what's going on with this new SAS controller. I swapped out my old Marvell based controller for a new Intel RS25GB008 and it seems that it never detects all the disks correctly (there are 4 attached to this controller).
Trying to pull out the relevant bits of dmesg (full version attached):
[ 4.197386] mpt2sas version 10.100.00.00 loaded
[ 4.197501] scsi2 : Fusion MPT SAS Host
[ 4.197825] mpt2sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.197835] mpt2sas 0000:01:00.0: setting latency timer to 64
[ 4.197840] mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (8146696 kB)
[ 4.197933] mpt2sas 0000:01:00.0: irq 47 for MSI/MSI-X
[ 4.197938] mpt2sas 0000:01:00.0: irq 48 for MSI/MSI-X
[ 4.197943] mpt2sas 0000:01:00.0: irq 49 for MSI/MSI-X
[ 4.197948] mpt2sas 0000:01:00.0: irq 50 for MSI/MSI-X
[ 4.197981] mpt2sas0-msix0: PCI-MSI-X enabled: IRQ 47
[ 4.197983] mpt2sas0-msix1: PCI-MSI-X enabled: IRQ 48
[ 4.197984] mpt2sas0-msix2: PCI-MSI-X enabled: IRQ 49
[ 4.197986] mpt2sas0-msix3: PCI-MSI-X enabled: IRQ 50
[ 4.197987] mpt2sas0: iomem(0x00000000dfef0000), mapped(0xffffc900122e0000), size(65536)
[ 4.197989] mpt2sas0: ioport(0x000000000000de00), size(256)
[ 4.440008] mpt2sas0: sending message unit reset !!
[ 4.446683] mpt2sas0: message unit reset: SUCCESS
[ 4.590327] mpt2sas0: Allocated physical memory: size(11195 kB)
[ 4.590330] mpt2sas0: Current Controller Queue Depth(4859), Max Controller Queue Depth(5120)
[ 4.590332] mpt2sas0: Scatter Gather Elements per IO(128)
[ 4.790353] mpt2sas0: LSISAS2308: FWVersion(09.00.00.00), ChipRevision(0x01), BiosVersion(07.17.03.00)
[ 4.790356] mpt2sas0: Intel(R) RAID Controller RS25GB008
[ 4.790358] mpt2sas0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set Full,NCQ)
[ 4.790423] mpt2sas0: sending port enable !!
[ 4.792873] mpt2sas0: host_add: handle(0x0001), sas_addr(0x500605b003f34c80), phys(8)
[ 4.803344] mpt2sas0: port enable: SUCCESS
[ 4.814391] scsi 2:0:0:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.814397] scsi 2:0:0:0: SATA: handle(0x0009), sas_addr(0x4433221100000000), phy(0), device_name(0x4ee250019f620672)
[ 4.814400] scsi 2:0:0:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(0)
[ 4.814489] scsi 2:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.814498] scsi 2:0:0:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.820459] sd 2:0:0:0: [sdc] physical block alignment offset: 4096
[ 4.820465] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.820468] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 4.829459] scsi 2:0:1:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.829465] scsi 2:0:1:0: SATA: handle(0x000a), sas_addr(0x4433221101000000), phy(1), device_name(0x4ee250010e9c0673)
[ 4.829468] scsi 2:0:1:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(1)
[ 4.829546] scsi 2:0:1:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.829551] scsi 2:0:1:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.837538] sd 2:0:1:0: [sdd] physical block alignment offset: 4096
[ 4.837543] sd 2:0:1:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.837545] sd 2:0:1:0: [sdd] 4096-byte physical blocks
[ 4.844069] scsi 2:0:2:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.844075] scsi 2:0:2:0: SATA: handle(0x000b), sas_addr(0x4433221102000000), phy(2), device_name(0x4ee25001c81a5bc7)
[ 4.844078] scsi 2:0:2:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(2)
[ 4.844153] scsi 2:0:2:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.844158] scsi 2:0:2:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.851179] sd 2:0:2:0: [sde] physical block alignment offset: 4096
[ 4.851184] sd 2:0:2:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.851186] sd 2:0:2:0: [sde] 4096-byte physical blocks
[ 4.851459] sd 2:0:0:0: [sdc] Write Protect is off
[ 4.851463] sd 2:0:0:0: [sdc] Mode Sense: 7f 00 00 08
[ 4.857728] scsi 2:0:3:0: Direct-Access ATA WDC WD30EZRX-00A 0A80 PQ: 0 ANSI: 5
[ 4.857734] scsi 2:0:3:0: SATA: handle(0x000c), sas_addr(0x4433221103000000), phy(3), device_name(0x4ee250010d1e0673)
[ 4.857737] scsi 2:0:3:0: SATA: enclosure_logical_id(0x500605b003f34c80), slot(3)
[ 4.857809] scsi 2:0:3:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 4.857814] scsi 2:0:3:0: qdepth(32), tagged(1), simple(0), ordered(0), scsi_level(6), cmd_que(1)
[ 4.858145] port-2:0: remove: sas_addr(0x4433221100000000)
[ 4.858154] port-2:0: remove: sas_addr(0x4433221100000000), phy(0)
[ 4.862435] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.862589] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.862592] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862594] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862623] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.862626] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.862628] sd 2:0:0:0: [sdc] Sense not available.
[ 4.862655] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.862902] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863127] sdc: detected capacity change from 3000592982016 to 0
[ 4.863199] sd 2:0:0:0: [sdc] READ CAPACITY(16) failed
[ 4.863201] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863203] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863222] sd 2:0:0:0: [sdc] READ CAPACITY failed
[ 4.863223] sd 2:0:0:0: [sdc] Result: hostbyte=0x01 driverbyte=0x00
[ 4.863226] sd 2:0:0:0: [sdc] Sense not available.
[ 4.863251] sd 2:0:0:0: [sdc] Asking for cache data failed
[ 4.863477] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[ 4.863702] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 4.864690] sd 2:0:3:0: [sdf] physical block alignment offset: 4096
[ 4.864695] sd 2:0:3:0: [sdf] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 4.864698] sd 2:0:3:0: [sdf] 4096-byte physical blocks
[ 4.876736] sd 2:0:1:0: [sdd] Write Protect is off
[ 4.876740] sd 2:0:1:0: [sdd] Mode Sense: 7f 00 00 08
[ 4.885584] sd 2:0:2:0: [sde] Write Protect is off
[ 4.885588] sd 2:0:2:0: [sde] Mode Sense: 7f 00 00 08
[ 4.891538] sd 2:0:1:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.897125] sd 2:0:3:0: [sdf] Write Protect is off
[ 4.897129] sd 2:0:3:0: [sdf] Mode Sense: 7f 00 00 08
[ 4.900113] sd 2:0:2:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.910240] sd 2:0:3:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.974155] sdf: sdf1
[ 4.975438] sdd: sdd1
[ 4.983617] sde: sde1
[ 5.026685] sd 2:0:3:0: [sdf] Attached SCSI disk
[ 5.032538] sd 2:0:1:0: [sdd] Attached SCSI disk
[ 5.039178] sd 2:0:2:0: [sde] Attached SCSI disk
[ 5.039528] mpt2sas0: removing handle(0x0009), sas_addr(0x4433221100000000)
[ 5.039532] mpt2sas0: failure at drivers/scsi/mpt2sas/mpt2sas_transport.c:705/mpt2sas_transport_port_add()!
Usually if I hot-unplug and re-plug the disk in question it will be detected properly, but next reboot I have the same problem again.
Does anything there point towards a hardware/software problem? I notice there's a newer RS25GB008 bios available, though I'll need to source a UEFI board in order to install it.
Thanks,
Kevin.
[-- Attachment #2: scsi-misc-2[1].6.git-2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45.patch --]
[-- Type: application/octet-stream, Size: 3221 bytes --]
From 2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45 Mon Sep 17 00:00:00 2001
From: "nagalakshmi.nandigama@lsi.com" <nagalakshmi.nandigama@lsi.com>
Date: Tue, 13 Dec 2011 09:29:15 +0530
Subject: [PATCH] [SCSI] mpt2sas: Removed redundant calling of
_scsih_probe_devices() from _scsih_probe
Removed redundant calling of _scsih_probe_devices() from _scsih_probe as
it is getting called from _scsih_scan_finished.
Also moved the function scsi_scan_host(shost) to get called after the
volumes on warp drive are reported to the OS. Otherwise by the time
the (ioc->hide_drives) flags is set, the volumes on warp drive
are reported to the OS already.
Also modified the initialization of reply queues only in case of driver load
time in the function _base_make_ioc_operational().
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
---
drivers/scsi/mpt2sas/mpt2sas_base.c | 20 +++++++-------------
drivers/scsi/mpt2sas/mpt2sas_scsih.c | 3 +--
2 files changed, 8 insertions(+), 15 deletions(-)
diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index 4819181..0b2c955 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -4099,7 +4099,8 @@ _base_make_ioc_operational(struct MPT2SAS_ADAPTER *ioc, int sleep_flag)
ioc->reply_free[i] = cpu_to_le32(reply_address);
/* initialize reply queues */
- _base_assign_reply_queues(ioc);
+ if (ioc->is_driver_loading)
+ _base_assign_reply_queues(ioc);
/* initialize Reply Post Free Queue */
reply_post_free = (long)ioc->reply_post_free;
@@ -4147,24 +4148,17 @@ _base_make_ioc_operational(struct MPT2SAS_ADAPTER *ioc, int sleep_flag)
if (ioc->is_driver_loading) {
-
-
-
- ioc->wait_for_discovery_to_complete =
- _base_determine_wait_on_discovery(ioc);
- return r; /* scan_start and scan_finished support */
- }
-
-
- if (ioc->wait_for_discovery_to_complete && ioc->is_warpdrive) {
- if (ioc->manu_pg10.OEMIdentifier == 0x80) {
+ if (ioc->is_warpdrive && ioc->manu_pg10.OEMIdentifier
+ == 0x80) {
hide_flag = (u8) (ioc->manu_pg10.OEMSpecificFlags0 &
MFG_PAGE10_HIDE_SSDS_MASK);
if (hide_flag != MFG_PAGE10_HIDE_SSDS_MASK)
ioc->mfg_pg10_hide_flag = hide_flag;
}
+ ioc->wait_for_discovery_to_complete =
+ _base_determine_wait_on_discovery(ioc);
+ return r; /* scan_start and scan_finished support */
}
-
r = _base_send_port_enable(ioc, sleep_flag);
if (r)
return r;
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 8cd4ebb..193e33e 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -8039,7 +8039,6 @@ _scsih_probe(struct pci_dev *pdev, const struct pci_device_id *id)
goto out_attach_fail;
}
- scsi_scan_host(shost);
if (ioc->is_warpdrive) {
if (ioc->mfg_pg10_hide_flag == MFG_PAGE10_EXPOSE_ALL_DISKS)
ioc->hide_drives = 0;
@@ -8053,8 +8052,8 @@ _scsih_probe(struct pci_dev *pdev, const struct pci_device_id *id)
}
} else
ioc->hide_drives = 0;
+ scsi_scan_host(shost);
- _scsih_probe_devices(ioc);
return 0;
out_attach_fail:
--
1.7.6.5
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
2012-01-25 5:22 ` Nandigama, Nagalakshmi
@ 2012-01-25 8:07 ` Kevin Shanahan
2012-01-28 5:02 ` Kevin Shanahan
0 siblings, 1 reply; 5+ messages in thread
From: Kevin Shanahan @ 2012-01-25 8:07 UTC (permalink / raw)
To: Nandigama, Nagalakshmi; +Cc: linux-scsi@vger.kernel.org
On Wed, Jan 25, 2012 at 10:52:34AM +0530, Nandigama, Nagalakshmi wrote:
> Request to apply the attached patch and test.
> scsi-misc-2[1].6.git-2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45.patch
Great, that fixes the issue!
Cheers,
Kevin.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
2012-01-25 8:07 ` Kevin Shanahan
@ 2012-01-28 5:02 ` Kevin Shanahan
2012-01-30 6:20 ` Nandigama, Nagalakshmi
0 siblings, 1 reply; 5+ messages in thread
From: Kevin Shanahan @ 2012-01-28 5:02 UTC (permalink / raw)
To: Nandigama, Nagalakshmi; +Cc: linux-scsi@vger.kernel.org, stable
On Wed, Jan 25, 2012 at 06:37:28PM +1030, Kevin Shanahan wrote:
> On Wed, Jan 25, 2012 at 10:52:34AM +0530, Nandigama, Nagalakshmi wrote:
> > Request to apply the attached patch and test.
> > scsi-misc-2[1].6.git-2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45.patch
>
> Great, that fixes the issue!
Any chance this patch can go into 3.2.3?
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45
Makes my Intel/LSI SAS controller usable, working great on top of
3.2.1 for several days now.
Thanks,
Kevin.
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
2012-01-28 5:02 ` Kevin Shanahan
@ 2012-01-30 6:20 ` Nandigama, Nagalakshmi
0 siblings, 0 replies; 5+ messages in thread
From: Nandigama, Nagalakshmi @ 2012-01-30 6:20 UTC (permalink / raw)
To: Kevin Shanahan; +Cc: linux-scsi@vger.kernel.org, stable@vger.kernel.org
Ok. Posted this patch to stable kernel today.
Regards,
Nagalakshmi
-----Original Message-----
From: Kevin Shanahan [mailto:kmshanah@disenchant.net]
Sent: Saturday, January 28, 2012 10:32 AM
To: Nandigama, Nagalakshmi
Cc: linux-scsi@vger.kernel.org; stable@vger.kernel.org
Subject: Re: READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add
On Wed, Jan 25, 2012 at 06:37:28PM +1030, Kevin Shanahan wrote:
> On Wed, Jan 25, 2012 at 10:52:34AM +0530, Nandigama, Nagalakshmi wrote:
> > Request to apply the attached patch and test.
> > scsi-misc-2[1].6.git-2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45.patch
>
> Great, that fixes the issue!
Any chance this patch can go into 3.2.3?
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=2cb6fc8c014b9b00c4487a79b8f6ed0da4121f45
Makes my Intel/LSI SAS controller usable, working great on top of
3.2.1 for several days now.
Thanks,
Kevin.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-01-30 6:20 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-01-25 1:57 READ CAPACITY(16) failed, failure in mpt2sas_transport_port_add Kevin Shanahan
2012-01-25 5:22 ` Nandigama, Nagalakshmi
2012-01-25 8:07 ` Kevin Shanahan
2012-01-28 5:02 ` Kevin Shanahan
2012-01-30 6:20 ` Nandigama, Nagalakshmi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).