From: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
To: james.bottomley@hansenpartnership.com
Cc: linux-scsi@vger.kernel.org, linux-kernel@vger.kernel.org,
matthew.gates@hp.com, stephenmcameron@gmail.com,
thenzl@redhat.com, akpm@linux-foundation.org,
mikem@beardog.cce.hp.com
Subject: [PATCH 00/17] hpsa updates for April, 2012
Date: Fri, 20 Apr 2012 10:06:11 -0500 [thread overview]
Message-ID: <20120420150349.10596.73732.stgit@beardog.cce.hp.com> (raw)
The two big changes here are adding an abort handler, and using multiple
reply queues for command completions.
Matt Bondurant (1):
hpsa: retry driver initiated commands on busy status
Matt Gates (2):
hpsa: use multiple reply queues
hpsa: refine interrupt handler locking for greater concurrency
Mike Miller (1):
hpsa: add new RAID level "1(ADM)"
Stephen M. Cameron (13):
hpsa: call pci_disable_device on driver unload
hpsa: do not skip disabled devices
hpsa: enable bus master bit after pci_enable_device
hpsa: suppress excessively chatty error messages
hpsa: do not read from controller unnecessarily in completion code
hpsa: remove unused parameter from finish_cmd
hpsa: add abort error handler function
hpsa: do aborts two ways
hpsa: factor out tail calls to next_command() in process_(non)indexed_cmd()
hpsa: factor out hpsa_free_irqs_and_disable_msix
hpsa: use new IS_ENABLED macro
hpsa: removed unused member maxQsinceinit
hpsa: dial down lockup detection during firmware flash
drivers/block/cciss.c | 2
drivers/scsi/hpsa.c | 689 +++++++++++++++++++++++++++++++++++++----------
drivers/scsi/hpsa.h | 85 ++++--
drivers/scsi/hpsa_cmd.h | 37 ++-
4 files changed, 643 insertions(+), 170 deletions(-)
--
-- steve
next reply other threads:[~2012-04-20 15:06 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-20 15:06 Stephen M. Cameron [this message]
2012-04-20 15:06 ` [PATCH 01/17] hpsa: call pci_disable_device on driver unload Stephen M. Cameron
2012-04-20 15:06 ` [PATCH 02/17] hpsa: do not skip disabled devices Stephen M. Cameron
2012-04-20 15:06 ` [PATCH 03/17] hpsa: enable bus master bit after pci_enable_device Stephen M. Cameron
2012-04-20 18:41 ` Khalid Aziz
2012-04-20 20:06 ` scameron
2012-04-20 15:06 ` [PATCH 04/17] hpsa: suppress excessively chatty error messages Stephen M. Cameron
2012-04-20 22:49 ` Shergill, Gurinder
2012-04-20 15:06 ` [PATCH 05/17] hpsa: do not read from controller unnecessarily in completion code Stephen M. Cameron
2012-04-20 15:06 ` [PATCH 06/17] hpsa: retry driver initiated commands on busy status Stephen M. Cameron
2012-04-20 22:51 ` Shergill, Gurinder
2012-04-20 15:06 ` [PATCH 07/17] hpsa: remove unused parameter from finish_cmd Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 08/17] hpsa: add abort error handler function Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 09/17] hpsa: do aborts two ways Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 10/17] hpsa: factor out tail calls to next_command() in process_(non)indexed_cmd() Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 11/17] hpsa: use multiple reply queues Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 12/17] hpsa: refine interrupt handler locking for greater concurrency Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 13/17] hpsa: factor out hpsa_free_irqs_and_disable_msix Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 14/17] hpsa: use new IS_ENABLED macro Stephen M. Cameron
2012-04-22 18:12 ` Paul Gortmaker
2012-04-23 2:20 ` Stephen Cameron
2012-04-23 13:56 ` Paul Gortmaker
2012-04-23 14:56 ` James Bottomley
2012-04-24 1:43 ` Paul Gortmaker
2012-04-24 8:25 ` James Bottomley
2012-04-24 15:15 ` Paul Gortmaker
2012-04-25 15:11 ` scameron
2012-04-20 15:07 ` [PATCH 15/17] hpsa: add new RAID level "1(ADM)" Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 16/17] hpsa: removed unused member maxQsinceinit Stephen M. Cameron
2012-04-20 15:07 ` [PATCH 17/17] hpsa: dial down lockup detection during firmware flash Stephen M. Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120420150349.10596.73732.stgit@beardog.cce.hp.com \
--to=scameron@beardog.cce.hp.com \
--cc=akpm@linux-foundation.org \
--cc=james.bottomley@hansenpartnership.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=matthew.gates@hp.com \
--cc=mikem@beardog.cce.hp.com \
--cc=stephenmcameron@gmail.com \
--cc=thenzl@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).