From: Don Brace <don.brace@pmcs.com>
To: scott.teel@pmcs.com, Kevin.Barnett@pmcs.com,
scott.benesh@pmcs.com, james.bottomley@parallels.com,
hch@infradead.org, Justin.Lindley@pmcs.com, elliott@hpe.com
Cc: linux-scsi@vger.kernel.org
Subject: [PATCH 19/21] hpsa: enhance device messages
Date: Sat, 24 Oct 2015 14:54:22 -0500 [thread overview]
Message-ID: <20151024195422.17127.55326.stgit@brunhilda> (raw)
In-Reply-To: <20151024193306.17127.7819.stgit@brunhilda>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
---
drivers/scsi/hpsa.c | 46 +++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 41 insertions(+), 5 deletions(-)
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index dfe5c21..1841b5a 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -607,7 +607,7 @@ static inline int is_logical_dev_addr_mode(unsigned char scsi3addr[])
}
static const char * const raid_label[] = { "0", "4", "1(+0)", "5", "5+1", "6",
- "1(+0)ADM", "UNKNOWN"
+ "1(+0)ADM", "UNKNOWN", "PHYS DRV"
};
#define HPSA_RAID_0 0
#define HPSA_RAID_4 1
@@ -616,7 +616,8 @@ static const char * const raid_label[] = { "0", "4", "1(+0)", "5", "5+1", "6",
#define HPSA_RAID_51 4
#define HPSA_RAID_6 5 /* also used for RAID 60 */
#define HPSA_RAID_ADM 6 /* also used for RAID 1+0 ADM */
-#define RAID_UNKNOWN (ARRAY_SIZE(raid_label) - 1)
+#define RAID_UNKNOWN (ARRAY_SIZE(raid_label) - 2)
+#define PHYSICAL_DRIVE (ARRAY_SIZE(raid_label) - 1)
static inline bool is_logical_device(struct hpsa_scsi_dev_t *device)
{
@@ -1142,19 +1143,54 @@ static int hpsa_find_target_lun(struct ctlr_info *h,
static inline void hpsa_show_dev_msg(const char *level, struct ctlr_info *h,
struct hpsa_scsi_dev_t *dev, char *description)
{
+#define LABEL_SIZE 15
+ char label[LABEL_SIZE];
+
+ switch (dev->devtype) {
+ case TYPE_RAID:
+ snprintf(label, LABEL_SIZE, "controller");
+ break;
+ case TYPE_ENCLOSURE:
+ snprintf(label, LABEL_SIZE, "enclosure");
+ break;
+ case TYPE_DISK:
+ if (dev->external)
+ snprintf(label, LABEL_SIZE, "external");
+ else if (!is_logical_dev_addr_mode(dev->scsi3addr))
+ snprintf(label, LABEL_SIZE, "%s",
+ raid_label[PHYSICAL_DRIVE]);
+ else
+ snprintf(label, LABEL_SIZE, "RAID-%s",
+ dev->raid_level > RAID_UNKNOWN ? "?" :
+ raid_label[dev->raid_level]);
+ break;
+ case TYPE_ROM:
+ snprintf(label, LABEL_SIZE, "rom");
+ break;
+ case TYPE_TAPE:
+ snprintf(label, LABEL_SIZE, "tape");
+ break;
+ case TYPE_MEDIUM_CHANGER:
+ snprintf(label, LABEL_SIZE, "changer");
+ break;
+ default:
+ snprintf(label, LABEL_SIZE, "UNKNOWN");
+ break;
+ }
+
+ "scsi %d:%d:%d:%d: %s %s %.8s %.16s %s SSDSmartPathCap%c En%c Exp=%d\n",
if (dev == NULL)
return;
dev_warn(&h->pdev->dev,
- "scsi %d:%d:%d:%d: %s %s %.8s %.16s RAID-%s SSDSmartPathCap%c En%c Exp=%d\n",
+ "scsi %d:%d:%d:%d: %s %s %.8s %.16s %s SSDSmartPathCap%c En%c Exp=%d\n",
h->scsi_host->host_no, dev->bus, dev->target, dev->lun,
description,
dev->devtype >= 0 ?
scsi_device_type(dev->devtype) : "unknown",
dev->vendor,
dev->model,
- dev->raid_level > RAID_UNKNOWN ?
- "RAID-?" : raid_label[dev->raid_level],
+ label,
dev->offload_config ? '+' : '-',
dev->offload_enabled ? '+' : '-',
dev->expose_device);
next prev parent reply other threads:[~2015-10-24 19:58 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-24 19:52 [PATCH 00/21] hpsa updates Don Brace
2015-10-24 19:52 ` [PATCH 01/21] hpsa: correct calls to dev_printk Don Brace
2015-10-26 12:52 ` Tomas Henzl
2015-10-26 13:41 ` Don Brace
2015-10-24 19:52 ` [PATCH 02/21] hpsa: allow driver requested rescans Don Brace
2015-10-26 14:36 ` Tomas Henzl
2015-10-24 19:52 ` [PATCH 03/21] hpsa: abandon rescans on memory alloaction failures Don Brace
2015-10-26 14:24 ` Tomas Henzl
2015-10-26 14:29 ` Don Brace
2015-10-26 14:32 ` Tomas Henzl
2015-10-26 14:36 ` Tomas Henzl
2015-10-24 19:52 ` [PATCH 04/21] hpsa: correct transfer length for 6 byte read/write commands Don Brace
2015-10-26 14:37 ` Tomas Henzl
2015-10-24 19:52 ` [PATCH 05/21] hpsa: fix hpsa_adjust_hpsa_scsi_table Don Brace
2015-10-26 14:55 ` Tomas Henzl
2015-10-26 15:22 ` Don Brace
2015-10-24 19:53 ` [PATCH 06/21] hpsa: fix physical target reset Don Brace
2015-10-24 19:53 ` [PATCH 07/21] hpsa: correct check for non-disk devices Don Brace
2015-10-24 19:53 ` [PATCH 08/21] hpsa: correct ioaccel2 sg chain len Don Brace
2015-10-24 19:53 ` [PATCH 09/21] hpsa: simplify check for device exposure Don Brace
2015-10-24 19:53 ` [PATCH 10/21] hpsa: simplify update scsi devices Don Brace
2015-10-24 19:53 ` [PATCH 11/21] hpsa: add function is_logical_device Don Brace
2015-10-24 19:53 ` [PATCH 12/21] hpsa: enhance hpsa_get_device_id Don Brace
2015-10-24 19:53 ` [PATCH 13/21] hpsa: refactor hpsa_figure_bus_target_lun Don Brace
2015-10-24 19:53 ` [PATCH 14/21] hpsa: move scsi_add_device and scsi_remove_device calls to new function Don Brace
2015-10-24 19:53 ` [PATCH 15/21] External array LUNs must use target and lun numbers assigned by the Don Brace
2015-10-24 19:54 ` [PATCH 16/21] hpsa: eliminate fake lun0 enclosures Don Brace
2015-10-24 19:54 ` [PATCH 17/21] hpsa: add discovery polling for PT RAID devices Don Brace
2015-10-24 19:54 ` [PATCH 18/21] hpsa: disable report lun data caching Don Brace
2015-10-24 19:54 ` Don Brace [this message]
2015-10-24 20:19 ` [PATCH 19/21] hpsa: enhance device messages kbuild test robot
2015-10-26 13:36 ` Don Brace
2015-10-24 19:54 ` [PATCH 20/21] hpsa: add in sas transport class Don Brace
2015-10-24 19:54 ` [PATCH 21/21] hpsa: bump the driver version Don Brace
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151024195422.17127.55326.stgit@brunhilda \
--to=don.brace@pmcs.com \
--cc=Justin.Lindley@pmcs.com \
--cc=Kevin.Barnett@pmcs.com \
--cc=elliott@hpe.com \
--cc=hch@infradead.org \
--cc=james.bottomley@parallels.com \
--cc=linux-scsi@vger.kernel.org \
--cc=scott.benesh@pmcs.com \
--cc=scott.teel@pmcs.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).