* Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34
@ 2016-12-14 12:07 Vasiliy Tolstov
2016-12-14 12:22 ` Johannes Thumshirn
2016-12-14 12:48 ` Greg KH
0 siblings, 2 replies; 5+ messages in thread
From: Vasiliy Tolstov @ 2016-12-14 12:07 UTC (permalink / raw)
To: linux-kernel; +Cc: stable, linux-scsi
Hi! I have stable problems with all Samsung SSD drivers like PM863 and
EVO 850 Pro.
Time after time scsi bus reset link with messages:
[ 2477.973617] ata1: exception Emask 0x50 SAct 0x0 SErr 0x4090800
action 0xe frozen
[ 2477.975036] ata1: irq_stat 0x00400040, connection status changed
[ 2477.976396] ata1: SError: { HostInt PHYRdyChg 10B8B DevExch }
[ 2477.977766] ata1: hard resetting link
[ 2478.701015] ata1: SATA link down (SStatus 0 SControl 300)
[ 2483.700924] ata1: hard resetting link
[ 2484.020924] ata1: SATA link down (SStatus 0 SControl 300)
[ 2484.022257] ata1: limiting SATA link speed to 1.5 Gbps
[ 2489.020766] ata1: hard resetting link
[ 2489.340828] ata1: SATA link down (SStatus 0 SControl 310)
[ 2489.342158] ata1.00: disabled
[ 2489.343452] ata1: EH complete
[ 2489.344806] ata1.00: detaching (SCSI 0:0:0:0)
[ 2489.347434] sd 0:0:0:0: [sda] Stopping disk
[ 2489.348605] sd 0:0:0:0: [sda] Start/Stop Unit failed: Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 3457.586929] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000
action 0xe frozen
[ 3457.588224] ata1: irq_stat 0x00000040, connection status changed
[ 3457.589453] ata1: SError: { CommWake DevExch }
[ 3457.590679] ata1: hard resetting link
[ 3458.312616] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3461.139831] ata1.00: ATA-9: SAMSUNG MZ7LM1T9HCJM-0E003, GXT3003Q,
max UDMA/133
[ 3461.141027] ata1.00: 3750748848 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 3461.142882] ata1.00: configured for UDMA/133
[ 3461.144004] ata1: EH complete
[ 3461.145545] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZ7LM1T9 003Q
PQ: 0 ANSI: 5
[ 3461.147069] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3461.147082] sd 0:0:0:0: [sda] 3750748848 512-byte logical blocks:
(1.92 TB/1.75 TiB)
[ 3461.147649] sd 0:0:0:0: [sda] Write Protect is off
[ 3461.147652] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3461.147849] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 3461.152457] sd 0:0:0:0: [sda] Attached SCSI removable disk
I'm try to remove drive and add it again message not appears may be
one hour or more. I'm try different servers from HP and Supermicro and
error is present. Also i'm try various disk from this series and
nothing changed.
If i have massive workload like writing to ext4 fs on this ssd drivers
i get corrupted ext4 journal and readonly fs.
My kernel version is 4.4.34
May be some Samsung engineers presented in this mailing list and ca
help to solve this errors? Or for server i need only Intel SSD (yes if
i use intel ssd this error not happening, this is not intel
advertising)
--
Vasiliy Tolstov,
e-mail: v.tolstov@selfip.ru
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34
2016-12-14 12:07 Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34 Vasiliy Tolstov
@ 2016-12-14 12:22 ` Johannes Thumshirn
2016-12-14 20:19 ` Vasiliy Tolstov
2016-12-14 12:48 ` Greg KH
1 sibling, 1 reply; 5+ messages in thread
From: Johannes Thumshirn @ 2016-12-14 12:22 UTC (permalink / raw)
To: Vasiliy Tolstov; +Cc: linux-kernel, stable, linux-scsi
On Wed, Dec 14, 2016 at 03:07:48PM +0300, Vasiliy Tolstov wrote:
> Hi! I have stable problems with all Samsung SSD drivers like PM863 and
> EVO 850 Pro.
>
> Time after time scsi bus reset link with messages:
> [ 2477.973617] ata1: exception Emask 0x50 SAct 0x0 SErr 0x4090800
> action 0xe frozen
> [ 2477.975036] ata1: irq_stat 0x00400040, connection status changed
> [ 2477.976396] ata1: SError: { HostInt PHYRdyChg 10B8B DevExch }
Random shot in the dark, have you tried changing the cable?
HostInt: HBA Internal error
PHYRdyChg: PhyRdy signal changed state
10B8B: 10b to 8b decoding error occurred
DevExch: Device presence has changed
This could indicate a problem with the cabling and/or connectors.
Byte,
Johannes
--
Johannes Thumshirn Storage
jthumshirn@suse.de +49 911 74053 689
SUSE LINUX GmbH, Maxfeldstr. 5, 90409 Nürnberg
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)
Key fingerprint = EC38 9CAB C2C4 F25D 8600 D0D0 0393 969D 2D76 0850
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34
2016-12-14 12:22 ` Johannes Thumshirn
@ 2016-12-14 20:19 ` Vasiliy Tolstov
0 siblings, 0 replies; 5+ messages in thread
From: Vasiliy Tolstov @ 2016-12-14 20:19 UTC (permalink / raw)
To: Johannes Thumshirn; +Cc: linux-kernel, stable, linux-scsi
2016-12-14 15:22 GMT+03:00 Johannes Thumshirn <jthumshirn@suse.de>:
> Random shot in the dark, have you tried changing the cable?
> HostInt: HBA Internal error
> PHYRdyChg: PhyRdy signal changed state
> 10B8B: 10b to 8b decoding error occurred
> DevExch: Device presence has changed
>
> This could indicate a problem with the cabling and/or connectors.
This can happening, but i don't have cables - all disk attached to
motherboard via internal drive bay. And also - ssd is new and this
problem persists across many servers.
--
Vasiliy Tolstov,
e-mail: v.tolstov@selfip.ru
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34
2016-12-14 12:07 Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34 Vasiliy Tolstov
2016-12-14 12:22 ` Johannes Thumshirn
@ 2016-12-14 12:48 ` Greg KH
2016-12-14 20:20 ` Vasiliy Tolstov
1 sibling, 1 reply; 5+ messages in thread
From: Greg KH @ 2016-12-14 12:48 UTC (permalink / raw)
To: Vasiliy Tolstov; +Cc: linux-kernel, stable, linux-scsi
On Wed, Dec 14, 2016 at 03:07:48PM +0300, Vasiliy Tolstov wrote:
> Hi! I have stable problems with all Samsung SSD drivers like PM863 and
> EVO 850 Pro.
>
> Time after time scsi bus reset link with messages:
> [ 2477.973617] ata1: exception Emask 0x50 SAct 0x0 SErr 0x4090800
> action 0xe frozen
> [ 2477.975036] ata1: irq_stat 0x00400040, connection status changed
> [ 2477.976396] ata1: SError: { HostInt PHYRdyChg 10B8B DevExch }
> [ 2477.977766] ata1: hard resetting link
> [ 2478.701015] ata1: SATA link down (SStatus 0 SControl 300)
> [ 2483.700924] ata1: hard resetting link
> [ 2484.020924] ata1: SATA link down (SStatus 0 SControl 300)
> [ 2484.022257] ata1: limiting SATA link speed to 1.5 Gbps
> [ 2489.020766] ata1: hard resetting link
> [ 2489.340828] ata1: SATA link down (SStatus 0 SControl 310)
> [ 2489.342158] ata1.00: disabled
> [ 2489.343452] ata1: EH complete
> [ 2489.344806] ata1.00: detaching (SCSI 0:0:0:0)
> [ 2489.347434] sd 0:0:0:0: [sda] Stopping disk
> [ 2489.348605] sd 0:0:0:0: [sda] Start/Stop Unit failed: Result:
> hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [ 3457.586929] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000
> action 0xe frozen
> [ 3457.588224] ata1: irq_stat 0x00000040, connection status changed
> [ 3457.589453] ata1: SError: { CommWake DevExch }
> [ 3457.590679] ata1: hard resetting link
> [ 3458.312616] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 3461.139831] ata1.00: ATA-9: SAMSUNG MZ7LM1T9HCJM-0E003, GXT3003Q,
> max UDMA/133
> [ 3461.141027] ata1.00: 3750748848 sectors, multi 16: LBA48 NCQ (depth
> 31/32), AA
> [ 3461.142882] ata1.00: configured for UDMA/133
> [ 3461.144004] ata1: EH complete
> [ 3461.145545] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZ7LM1T9 003Q
> PQ: 0 ANSI: 5
> [ 3461.147069] sd 0:0:0:0: Attached scsi generic sg0 type 0
> [ 3461.147082] sd 0:0:0:0: [sda] 3750748848 512-byte logical blocks:
> (1.92 TB/1.75 TiB)
> [ 3461.147649] sd 0:0:0:0: [sda] Write Protect is off
> [ 3461.147652] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 3461.147849] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 3461.152457] sd 0:0:0:0: [sda] Attached SCSI removable disk
>
> I'm try to remove drive and add it again message not appears may be
> one hour or more. I'm try different servers from HP and Supermicro and
> error is present. Also i'm try various disk from this series and
> nothing changed.
>
> If i have massive workload like writing to ext4 fs on this ssd drivers
> i get corrupted ext4 journal and readonly fs.
>
> My kernel version is 4.4.34
> May be some Samsung engineers presented in this mailing list and ca
> help to solve this errors? Or for server i need only Intel SSD (yes if
> i use intel ssd this error not happening, this is not intel
> advertising)
Do you also have problems with this on the 4.9 kernel release? We can't
add any changes to 4.4 that is not already made in 4.9.
thanks,
greg k-h
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-12-14 20:20 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-12-14 12:07 Samsung SSD 1.92TB PM863 Enterprise 2.5" SATA3 errors withc stable 4.4.34 Vasiliy Tolstov
2016-12-14 12:22 ` Johannes Thumshirn
2016-12-14 20:19 ` Vasiliy Tolstov
2016-12-14 12:48 ` Greg KH
2016-12-14 20:20 ` Vasiliy Tolstov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).