[PATCH AUTOSEL 5.6 077/149] scsi: lpfc: Fix RQ buffer leakage when no IOCBs available

[PATCH AUTOSEL 5.6 077/149] scsi: lpfc: Fix RQ buffer leakage when no IOCBs available

[Sasha Levin]

From: James Smart <jsmart2021@gmail.com>

[ Upstream commit 39c4f1a965a9244c3ba60695e8ff8da065ec6ac4 ]

The driver is occasionally seeing the following SLI Port error, requiring
reset and reinit:

 Port Status Event: ... error 1=0x52004a01, error 2=0x218

The failure means an RQ timeout. That is, the adapter had received
asynchronous receive frames, ran out of buffer slots to place the frames,
and the driver did not replenish the buffer slots before a timeout
occurred. The driver should not be so slow in replenishing buffers that a
timeout can occur.

When the driver received all the frames of a sequence, it allocates an IOCB
to put the frames in. In a situation where there was no IOCB available for
the frame of a sequence, the RQ buffer corresponding to the first frame of
the sequence was not returned to the FW. Eventually, with enough traffic
encountering the situation, the timeout occurred.

Fix by releasing the buffer back to firmware whenever there is no IOCB for
the first frame.

[mkp: typo]

Link: https://lore.kernel.org/r/20200128002312.16346-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/lpfc/lpfc_sli.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/scsi/lpfc/lpfc_sli.c b/drivers/scsi/lpfc/lpfc_sli.c
index 64002b0cb02d4..ab6f58bc80a48 100644
--- a/drivers/scsi/lpfc/lpfc_sli.c
+++ b/drivers/scsi/lpfc/lpfc_sli.c
@@ -17950,6 +17950,10 @@ lpfc_prep_seq(struct lpfc_vport *vport, struct hbq_dmabuf *seq_dmabuf)
 			list_add_tail(&iocbq->list, &first_iocbq->list);
 		}
 	}
+	/* Free the sequence's header buffer */
+	if (!first_iocbq)
+		lpfc_in_buf_free(vport->phba, &seq_dmabuf->dbuf);
+
 	return first_iocbq;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 5.6 092/149] scsi: qla2xxx: Handle NVME status iocb correctly

[Sasha Levin]

From: Arun Easi <aeasi@marvell.com>

[ Upstream commit 3d582b34992ba2fe4065f01019f0c08d12916faa ]

Certain state flags bit combinations are not checked and not handled
correctly. Plus, do not log a normal underrun situation where there is
no frame drop.

Link: https://lore.kernel.org/r/20200226224022.24518-17-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_isr.c | 47 ++++++++++++++++++++++++++++------
 1 file changed, 39 insertions(+), 8 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c
index e40705d38cea7..afaf9d483cd29 100644
--- a/drivers/scsi/qla2xxx/qla_isr.c
+++ b/drivers/scsi/qla2xxx/qla_isr.c
@@ -1910,6 +1910,7 @@ static void qla24xx_nvme_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
 	struct nvmefc_fcp_req *fd;
 	uint16_t        ret = QLA_SUCCESS;
 	uint16_t	comp_status = le16_to_cpu(sts->comp_status);
+	int		logit = 0;
 
 	iocb = &sp->u.iocb_cmd;
 	fcport = sp->fcport;
@@ -1920,6 +1921,12 @@ static void qla24xx_nvme_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
 	if (unlikely(iocb->u.nvme.aen_op))
 		atomic_dec(&sp->vha->hw->nvme_active_aen_cnt);
 
+	if (unlikely(comp_status != CS_COMPLETE))
+		logit = 1;
+
+	fd->transferred_length = fd->payload_length -
+	    le32_to_cpu(sts->residual_len);
+
 	/*
 	 * State flags: Bit 6 and 0.
 	 * If 0 is set, we don't care about 6.
@@ -1930,8 +1937,20 @@ static void qla24xx_nvme_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
 	 */
 	if (!(state_flags & (SF_FCP_RSP_DMA | SF_NVME_ERSP))) {
 		iocb->u.nvme.rsp_pyld_len = 0;
-	} else if ((state_flags & SF_FCP_RSP_DMA)) {
+	} else if ((state_flags & (SF_FCP_RSP_DMA | SF_NVME_ERSP)) ==
+			(SF_FCP_RSP_DMA | SF_NVME_ERSP)) {
+		/* Response already DMA'd to fd->rspaddr. */
 		iocb->u.nvme.rsp_pyld_len = le16_to_cpu(sts->nvme_rsp_pyld_len);
+	} else if ((state_flags & SF_FCP_RSP_DMA)) {
+		/*
+		 * Non-zero value in first 12 bytes of NVMe_RSP IU, treat this
+		 * as an error.
+		 */
+		iocb->u.nvme.rsp_pyld_len = 0;
+		fd->transferred_length = 0;
+		ql_dbg(ql_dbg_io, fcport->vha, 0x307a,
+			"Unexpected values in NVMe_RSP IU.\n");
+		logit = 1;
 	} else if (state_flags & SF_NVME_ERSP) {
 		uint32_t *inbuf, *outbuf;
 		uint16_t iter;
@@ -1954,16 +1973,28 @@ static void qla24xx_nvme_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
 		iter = iocb->u.nvme.rsp_pyld_len >> 2;
 		for (; iter; iter--)
 			*outbuf++ = swab32(*inbuf++);
-	} else { /* unhandled case */
-	    ql_log(ql_log_warn, fcport->vha, 0x503a,
-		"NVME-%s error. Unhandled state_flags of %x\n",
-		sp->name, state_flags);
 	}
 
-	fd->transferred_length = fd->payload_length -
-	    le32_to_cpu(sts->residual_len);
+	if (state_flags & SF_NVME_ERSP) {
+		struct nvme_fc_ersp_iu *rsp_iu = fd->rspaddr;
+		u32 tgt_xfer_len;
 
-	if (unlikely(comp_status != CS_COMPLETE))
+		tgt_xfer_len = be32_to_cpu(rsp_iu->xfrd_len);
+		if (fd->transferred_length != tgt_xfer_len) {
+			ql_dbg(ql_dbg_io, fcport->vha, 0x3079,
+				"Dropped frame(s) detected (sent/rcvd=%u/%u).\n",
+				tgt_xfer_len, fd->transferred_length);
+			logit = 1;
+		} else if (comp_status == CS_DATA_UNDERRUN) {
+			/*
+			 * Do not log if this is just an underflow and there
+			 * is no data loss.
+			 */
+			logit = 0;
+		}
+	}
+
+	if (unlikely(logit))
 		ql_log(ql_log_warn, fcport->vha, 0x5060,
 		   "NVME-%s ERR Handling - hdl=%x status(%x) tr_len:%x resid=%x  ox_id=%x\n",
 		   sp->name, sp->handle, comp_status,
-- 
2.20.1

[PATCH AUTOSEL 5.6 099/149] scsi: aacraid: Disabling TM path and only processing IOP reset

[Sasha Levin]

From: Sagar Biradar <Sagar.Biradar@microchip.com>

[ Upstream commit bef18d308a2215eff8c3411a23d7f34604ce56c3 ]

Fixes the occasional adapter panic when sg_reset is issued with -d, -t, -b
and -H flags.  Removal of command type HBA_IU_TYPE_SCSI_TM_REQ in
aac_hba_send since iu_type, request_id and fib_flags are not populated.
Device and target reset handlers are made to send TMF commands only when
reset_state is 0.

Link: https://lore.kernel.org/r/1581553771-25796-1-git-send-email-Sagar.Biradar@microchip.com
Reviewed-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/aacraid/commsup.c |  2 +-
 drivers/scsi/aacraid/linit.c   | 34 +++++++++++++++++++++++++---------
 2 files changed, 26 insertions(+), 10 deletions(-)

diff --git a/drivers/scsi/aacraid/commsup.c b/drivers/scsi/aacraid/commsup.c
index 5a8a999606ea3..5118bee865b39 100644
--- a/drivers/scsi/aacraid/commsup.c
+++ b/drivers/scsi/aacraid/commsup.c
@@ -729,7 +729,7 @@ int aac_hba_send(u8 command, struct fib *fibptr, fib_callback callback,
 		hbacmd->request_id =
 			cpu_to_le32((((u32)(fibptr - dev->fibs)) << 2) + 1);
 		fibptr->flags |= FIB_CONTEXT_FLAG_SCSI_CMD;
-	} else if (command != HBA_IU_TYPE_SCSI_TM_REQ)
+	} else
 		return -EINVAL;
 
 
diff --git a/drivers/scsi/aacraid/linit.c b/drivers/scsi/aacraid/linit.c
index ee6bc2f9b80ad..9130e038c45fb 100644
--- a/drivers/scsi/aacraid/linit.c
+++ b/drivers/scsi/aacraid/linit.c
@@ -731,7 +731,11 @@ static int aac_eh_abort(struct scsi_cmnd* cmd)
 		status = aac_hba_send(HBA_IU_TYPE_SCSI_TM_REQ, fib,
 				  (fib_callback) aac_hba_callback,
 				  (void *) cmd);
-
+		if (status != -EINPROGRESS) {
+			aac_fib_complete(fib);
+			aac_fib_free(fib);
+			return ret;
+		}
 		/* Wait up to 15 secs for completion */
 		for (count = 0; count < 15; ++count) {
 			if (cmd->SCp.sent_command) {
@@ -910,11 +914,11 @@ static int aac_eh_dev_reset(struct scsi_cmnd *cmd)
 
 	info = &aac->hba_map[bus][cid];
 
-	if (info->devtype != AAC_DEVTYPE_NATIVE_RAW &&
-	    info->reset_state > 0)
+	if (!(info->devtype == AAC_DEVTYPE_NATIVE_RAW &&
+	 !(info->reset_state > 0)))
 		return FAILED;
 
-	pr_err("%s: Host adapter reset request. SCSI hang ?\n",
+	pr_err("%s: Host device reset request. SCSI hang ?\n",
 	       AAC_DRIVERNAME);
 
 	fib = aac_fib_alloc(aac);
@@ -929,7 +933,12 @@ static int aac_eh_dev_reset(struct scsi_cmnd *cmd)
 	status = aac_hba_send(command, fib,
 			      (fib_callback) aac_tmf_callback,
 			      (void *) info);
-
+	if (status != -EINPROGRESS) {
+		info->reset_state = 0;
+		aac_fib_complete(fib);
+		aac_fib_free(fib);
+		return ret;
+	}
 	/* Wait up to 15 seconds for completion */
 	for (count = 0; count < 15; ++count) {
 		if (info->reset_state == 0) {
@@ -968,11 +977,11 @@ static int aac_eh_target_reset(struct scsi_cmnd *cmd)
 
 	info = &aac->hba_map[bus][cid];
 
-	if (info->devtype != AAC_DEVTYPE_NATIVE_RAW &&
-	    info->reset_state > 0)
+	if (!(info->devtype == AAC_DEVTYPE_NATIVE_RAW &&
+	 !(info->reset_state > 0)))
 		return FAILED;
 
-	pr_err("%s: Host adapter reset request. SCSI hang ?\n",
+	pr_err("%s: Host target reset request. SCSI hang ?\n",
 	       AAC_DRIVERNAME);
 
 	fib = aac_fib_alloc(aac);
@@ -989,6 +998,13 @@ static int aac_eh_target_reset(struct scsi_cmnd *cmd)
 			      (fib_callback) aac_tmf_callback,
 			      (void *) info);
 
+	if (status != -EINPROGRESS) {
+		info->reset_state = 0;
+		aac_fib_complete(fib);
+		aac_fib_free(fib);
+		return ret;
+	}
+
 	/* Wait up to 15 seconds for completion */
 	for (count = 0; count < 15; ++count) {
 		if (info->reset_state <= 0) {
@@ -1041,7 +1057,7 @@ static int aac_eh_bus_reset(struct scsi_cmnd* cmd)
 		}
 	}
 
-	pr_err("%s: Host adapter reset request. SCSI hang ?\n", AAC_DRIVERNAME);
+	pr_err("%s: Host bus reset request. SCSI hang ?\n", AAC_DRIVERNAME);
 
 	/*
 	 * Check the health of the controller
-- 
2.20.1

[PATCH AUTOSEL 5.6 100/149] scsi: core: avoid repetitive logging of device offline messages

[Sasha Levin]

From: "Ewan D. Milne" <emilne@redhat.com>

[ Upstream commit b0962c53bde9a485c8ebc401fa1dbe821a76bc3e ]

Large queues of I/O to offline devices that are eventually submitted when
devices are unblocked result in a many repeated "rejecting I/O to offline
device" messages.  These messages can fill up the dmesg buffer in crash
dumps so no useful prior messages remain.  In addition, if a serial console
is used, the flood of messages can cause a hard lockup in the console code.

Introduce a flag indicating the message has already been logged for the
device, and reset the flag when scsi_device_set_state() changes the device
state.

Link: https://lore.kernel.org/r/20200311143930.20674-1-emilne@redhat.com
Reviewed-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/scsi_lib.c    | 8 ++++++--
 include/scsi/scsi_device.h | 3 +++
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index 610ee41fa54cb..a45e7289dbbe7 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -1240,8 +1240,11 @@ scsi_prep_state_check(struct scsi_device *sdev, struct request *req)
 		 * commands.  The device must be brought online
 		 * before trying any recovery commands.
 		 */
-		sdev_printk(KERN_ERR, sdev,
-			    "rejecting I/O to offline device\n");
+		if (!sdev->offline_already) {
+			sdev->offline_already = true;
+			sdev_printk(KERN_ERR, sdev,
+				    "rejecting I/O to offline device\n");
+		}
 		return BLK_STS_IOERR;
 	case SDEV_DEL:
 		/*
@@ -2340,6 +2343,7 @@ scsi_device_set_state(struct scsi_device *sdev, enum scsi_device_state state)
 		break;
 
 	}
+	sdev->offline_already = false;
 	sdev->sdev_state = state;
 	return 0;
 
diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h
index f8312a3e5b429..cd9656ff3c43c 100644
--- a/include/scsi/scsi_device.h
+++ b/include/scsi/scsi_device.h
@@ -204,6 +204,9 @@ struct scsi_device {
 	unsigned unmap_limit_for_ws:1;	/* Use the UNMAP limit for WRITE SAME */
 	unsigned rpm_autosuspend:1;	/* Enable runtime autosuspend at device
 					 * creation time */
+
+	bool offline_already;		/* Device offline message logged */
+
 	atomic_t disk_events_disable_depth; /* disable depth for disk events */
 
 	DECLARE_BITMAP(supported_events, SDEV_EVT_MAXBITS); /* supported events */
-- 
2.20.1

[PATCH AUTOSEL 5.6 121/149] scsi: qla2xxx: Return appropriate failure through BSG Interface

[Sasha Levin]

From: Michael Hernandez <mhernandez@marvell.com>

[ Upstream commit 1b81e7f3019d632a707e07927e946ffbbc102910 ]

This patch ensures flash updates API calls return possible failure
status through BSG interface to the application.

Link: https://lore.kernel.org/r/20200226224022.24518-7-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_bsg.c |  9 +++++++--
 drivers/scsi/qla2xxx/qla_sup.c | 13 ++++++++-----
 2 files changed, 15 insertions(+), 7 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_bsg.c b/drivers/scsi/qla2xxx/qla_bsg.c
index d7169e43f5e18..d6f814aa94aba 100644
--- a/drivers/scsi/qla2xxx/qla_bsg.c
+++ b/drivers/scsi/qla2xxx/qla_bsg.c
@@ -1506,10 +1506,15 @@ qla2x00_update_optrom(struct bsg_job *bsg_job)
 	    bsg_job->request_payload.sg_cnt, ha->optrom_buffer,
 	    ha->optrom_region_size);
 
-	ha->isp_ops->write_optrom(vha, ha->optrom_buffer,
+	rval = ha->isp_ops->write_optrom(vha, ha->optrom_buffer,
 	    ha->optrom_region_start, ha->optrom_region_size);
 
-	bsg_reply->result = DID_OK;
+	if (rval) {
+		bsg_reply->result = -EINVAL;
+		rval = -EINVAL;
+	} else {
+		bsg_reply->result = DID_OK;
+	}
 	vfree(ha->optrom_buffer);
 	ha->optrom_buffer = NULL;
 	ha->optrom_state = QLA_SWAITING;
diff --git a/drivers/scsi/qla2xxx/qla_sup.c b/drivers/scsi/qla2xxx/qla_sup.c
index 76a38bf86cbc3..3da79ee1d88e4 100644
--- a/drivers/scsi/qla2xxx/qla_sup.c
+++ b/drivers/scsi/qla2xxx/qla_sup.c
@@ -2683,7 +2683,7 @@ qla28xx_write_flash_data(scsi_qla_host_t *vha, uint32_t *dwptr, uint32_t faddr,
 	uint32_t sec_mask, rest_addr, fdata;
 	void *optrom = NULL;
 	dma_addr_t optrom_dma;
-	int rval;
+	int rval, ret;
 	struct secure_flash_update_block *sfub;
 	dma_addr_t sfub_dma;
 	uint32_t offset = faddr << 2;
@@ -2939,11 +2939,12 @@ qla28xx_write_flash_data(scsi_qla_host_t *vha, uint32_t *dwptr, uint32_t faddr,
 write_protect:
 	ql_log(ql_log_warn + ql_dbg_verbose, vha, 0x7095,
 	    "Protect flash...\n");
-	rval = qla24xx_protect_flash(vha);
-	if (rval) {
+	ret = qla24xx_protect_flash(vha);
+	if (ret) {
 		qla81xx_fac_semaphore_access(vha, FAC_SEMAPHORE_UNLOCK);
 		ql_log(ql_log_warn, vha, 0x7099,
 		    "Failed protect flash\n");
+		rval = QLA_COMMAND_ERROR;
 	}
 
 	if (reset_to_rom == true) {
@@ -2951,10 +2952,12 @@ qla28xx_write_flash_data(scsi_qla_host_t *vha, uint32_t *dwptr, uint32_t faddr,
 		set_bit(ISP_ABORT_NEEDED, &vha->dpc_flags);
 		qla2xxx_wake_dpc(vha);
 
-		rval = qla2x00_wait_for_hba_online(vha);
-		if (rval != QLA_SUCCESS)
+		ret = qla2x00_wait_for_hba_online(vha);
+		if (ret != QLA_SUCCESS) {
 			ql_log(ql_log_warn, vha, 0xffff,
 			    "Adapter did not come out of reset\n");
+			rval = QLA_COMMAND_ERROR;
+		}
 	}
 
 done:
-- 
2.20.1

[PATCH AUTOSEL 5.6 123/149] scsi: qla2xxx: fix FW resource count values

[Sasha Levin]

From: Quinn Tran <qutran@marvell.com>

[ Upstream commit ce1ee122e0f048fc67c1259489f0802a28049bfd ]

This patch fixes issue where current and original exchanges count
were swapped for intiator and targets.

Also fix IOCB count for current and original which were swapped.

Link: https://lore.kernel.org/r/20200226224022.24518-9-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_dfs.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_dfs.c b/drivers/scsi/qla2xxx/qla_dfs.c
index 0a6fb359f4d5e..e62b2115235e1 100644
--- a/drivers/scsi/qla2xxx/qla_dfs.c
+++ b/drivers/scsi/qla2xxx/qla_dfs.c
@@ -134,11 +134,11 @@ qla_dfs_fw_resource_cnt_show(struct seq_file *s, void *unused)
 	} else {
 		seq_puts(s, "FW Resource count\n\n");
 		seq_printf(s, "Original TGT exchg count[%d]\n", mb[1]);
-		seq_printf(s, "current TGT exchg count[%d]\n", mb[2]);
-		seq_printf(s, "original Initiator Exchange count[%d]\n", mb[3]);
-		seq_printf(s, "Current Initiator Exchange count[%d]\n", mb[6]);
-		seq_printf(s, "Original IOCB count[%d]\n", mb[7]);
-		seq_printf(s, "Current IOCB count[%d]\n", mb[10]);
+		seq_printf(s, "Current TGT exchg count[%d]\n", mb[2]);
+		seq_printf(s, "Current Initiator Exchange count[%d]\n", mb[3]);
+		seq_printf(s, "Original Initiator Exchange count[%d]\n", mb[6]);
+		seq_printf(s, "Current IOCB count[%d]\n", mb[7]);
+		seq_printf(s, "Original IOCB count[%d]\n", mb[10]);
 		seq_printf(s, "MAX VP count[%d]\n", mb[11]);
 		seq_printf(s, "MAX FCF count[%d]\n", mb[12]);
 		seq_printf(s, "Current free pageable XCB buffer cnt[%d]\n",
@@ -149,7 +149,6 @@ qla_dfs_fw_resource_cnt_show(struct seq_file *s, void *unused)
 		    mb[22]);
 		seq_printf(s, "Original Target fast XCB buffer cnt[%d]\n",
 		    mb[23]);
-
 	}
 
 	return 0;
-- 
2.20.1

[PATCH AUTOSEL 5.6 126/149] scsi: qla2xxx: Add fixes for mailbox command

[Sasha Levin]

From: Himanshu Madhani <hmadhani@marvell.com>

[ Upstream commit 345f574dac85276d1471492c6e90c57e3f90a4f3 ]

This patch fixes:

- qla2x00_issue_iocb_timeout will now return if chip is down

- only check for sp->qpair in abort handling

Link: https://lore.kernel.org/r/20200212214436.25532-24-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_mbx.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c
index 9e09964f5c0e4..f0846ce0c4da4 100644
--- a/drivers/scsi/qla2xxx/qla_mbx.c
+++ b/drivers/scsi/qla2xxx/qla_mbx.c
@@ -1405,6 +1405,9 @@ qla2x00_issue_iocb_timeout(scsi_qla_host_t *vha, void *buffer,
 	mbx_cmd_t	mc;
 	mbx_cmd_t	*mcp = &mc;
 
+	if (qla2x00_chip_is_down(vha))
+		return QLA_INVALID_COMMAND;
+
 	ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1038,
 	    "Entered %s.\n", __func__);
 
@@ -1475,7 +1478,7 @@ qla2x00_abort_command(srb_t *sp)
 	ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x103b,
 	    "Entered %s.\n", __func__);
 
-	if (vha->flags.qpairs_available && sp->qpair)
+	if (sp->qpair)
 		req = sp->qpair->req;
 	else
 		req = vha->req;
-- 
2.20.1

[PATCH AUTOSEL 5.6 127/149] scsi: qla2xxx: Fix control flags for login/logout IOCB

[Sasha Levin]

From: Himanshu Madhani <hmadhani@marvell.com>

[ Upstream commit 419ae5fe73e50084fa794934fb62fab34f564b7c ]

This patch fixes control flag options for login/logout IOCB.

Link: https://lore.kernel.org/r/20200212214436.25532-23-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_iocb.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_iocb.c b/drivers/scsi/qla2xxx/qla_iocb.c
index 47bf60a9490a0..86881d68af19b 100644
--- a/drivers/scsi/qla2xxx/qla_iocb.c
+++ b/drivers/scsi/qla2xxx/qla_iocb.c
@@ -2362,6 +2362,8 @@ qla24xx_login_iocb(srb_t *sp, struct logio_entry_24xx *logio)
 	struct srb_iocb *lio = &sp->u.iocb_cmd;
 
 	logio->entry_type = LOGINOUT_PORT_IOCB_TYPE;
+	logio->control_flags = cpu_to_le16(LCF_COMMAND_PLOGI);
+
 	if (lio->u.logio.flags & SRB_LOGIN_PRLI_ONLY) {
 		logio->control_flags = cpu_to_le16(LCF_COMMAND_PRLI);
 	} else {
@@ -2939,7 +2941,6 @@ qla24xx_els_dcmd2_iocb(scsi_qla_host_t *vha, int els_opcode,
 	sp->fcport = fcport;
 
 	elsio->timeout = qla2x00_els_dcmd2_iocb_timeout;
-	init_completion(&elsio->u.els_plogi.comp);
 	if (wait)
 		sp->flags = SRB_WAKEUP_ON_COMP;
 
@@ -2949,7 +2950,7 @@ qla24xx_els_dcmd2_iocb(scsi_qla_host_t *vha, int els_opcode,
 	elsio->u.els_plogi.tx_size = elsio->u.els_plogi.rx_size = DMA_POOL_SIZE;
 
 	ptr = elsio->u.els_plogi.els_plogi_pyld =
-	    dma_alloc_coherent(&ha->pdev->dev, DMA_POOL_SIZE,
+	    dma_alloc_coherent(&ha->pdev->dev, elsio->u.els_plogi.tx_size,
 		&elsio->u.els_plogi.els_plogi_pyld_dma, GFP_KERNEL);
 
 	if (!elsio->u.els_plogi.els_plogi_pyld) {
@@ -2958,7 +2959,7 @@ qla24xx_els_dcmd2_iocb(scsi_qla_host_t *vha, int els_opcode,
 	}
 
 	resp_ptr = elsio->u.els_plogi.els_resp_pyld =
-	    dma_alloc_coherent(&ha->pdev->dev, DMA_POOL_SIZE,
+	    dma_alloc_coherent(&ha->pdev->dev, elsio->u.els_plogi.rx_size,
 		&elsio->u.els_plogi.els_resp_pyld_dma, GFP_KERNEL);
 
 	if (!elsio->u.els_plogi.els_resp_pyld) {
@@ -2982,6 +2983,7 @@ qla24xx_els_dcmd2_iocb(scsi_qla_host_t *vha, int els_opcode,
 	    (uint8_t *)elsio->u.els_plogi.els_plogi_pyld,
 	    sizeof(*elsio->u.els_plogi.els_plogi_pyld));
 
+	init_completion(&elsio->u.els_plogi.comp);
 	rval = qla2x00_start_sp(sp);
 	if (rval != QLA_SUCCESS) {
 		rval = QLA_FUNCTION_FAILED;
-- 
2.20.1

[PATCH AUTOSEL 5.6 128/149] scsi: qla2xxx: Fix qla2x00_echo_test() based on ISP type

[Sasha Levin]

From: Joe Carnuccio <joe.carnuccio@cavium.com>

[ Upstream commit 83cfd3dc002fc730387a1ec5fa0d4097cc31ee9f ]

Ths patch fixes MBX in-direction for setting right bits for
qla2x00_echo_test()

Link: https://lore.kernel.org/r/20200212214436.25532-19-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_mbx.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c
index f0846ce0c4da4..0e8426e1e1149 100644
--- a/drivers/scsi/qla2xxx/qla_mbx.c
+++ b/drivers/scsi/qla2xxx/qla_mbx.c
@@ -5173,10 +5173,11 @@ qla2x00_echo_test(scsi_qla_host_t *vha, struct msg_echo_lb *mreq,
 		mcp->out_mb |= MBX_2;
 
 	mcp->in_mb = MBX_0;
-	if (IS_QLA24XX_TYPE(ha) || IS_QLA25XX(ha) ||
-	    IS_CNA_CAPABLE(ha) || IS_QLA2031(ha))
+	if (IS_CNA_CAPABLE(ha) || IS_QLA24XX_TYPE(ha) || IS_QLA25XX(ha) ||
+	    IS_QLA2031(ha) || IS_QLA27XX(ha) || IS_QLA28XX(ha))
 		mcp->in_mb |= MBX_1;
-	if (IS_CNA_CAPABLE(ha) || IS_QLA2031(ha))
+	if (IS_CNA_CAPABLE(ha) || IS_QLA2031(ha) || IS_QLA27XX(ha) ||
+	    IS_QLA28XX(ha))
 		mcp->in_mb |= MBX_3;
 
 	mcp->tov = MBX_TOV_SECONDS;
-- 
2.20.1

[PATCH AUTOSEL 5.6 129/149] scsi: ufs: Fix ufshcd_hold() caused scheduling while atomic

[Sasha Levin]

From: Can Guo <cang@codeaurora.org>

[ Upstream commit c63d6099a7959ecc919b2549dc6b71f53521f819 ]

The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.

Fixes: f2a785ac2312 ("scsi: ufshcd: Fix race between clk scaling and ungate work")
Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/ufs/ufshcd.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 2d705694636c2..682f85f800d0f 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -1518,6 +1518,11 @@ int ufshcd_hold(struct ufs_hba *hba, bool async)
 		 */
 		if (ufshcd_can_hibern8_during_gating(hba) &&
 		    ufshcd_is_link_hibern8(hba)) {
+			if (async) {
+				rc = -EAGAIN;
+				hba->clk_gating.active_reqs--;
+				break;
+			}
 			spin_unlock_irqrestore(hba->host->host_lock, flags);
 			flush_work(&hba->clk_gating.ungate_work);
 			spin_lock_irqsave(hba->host->host_lock, flags);
-- 
2.20.1

[PATCH AUTOSEL 5.6 131/149] scsi: ufs: ufs-mediatek: ensure UniPro is not powered down before linkup

[Sasha Levin]

From: Stanley Chu <stanley.chu@mediatek.com>

[ Upstream commit 7742ca797aa79f280853ffd3e7d2e2af3cd317a5 ]

MediaTek Chipsets can enter proprietary UniPro low-power mode during
suspend while link is in hibern8 state. Make sure leaving low-power mode
before every link startup to prevent lockup in any possible error recovery
path.

At the same time, re-factor related funcitons to improve code readability.

Link: https://lore.kernel.org/r/20200129105251.12466-2-stanley.chu@mediatek.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/ufs/ufs-mediatek.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/scsi/ufs/ufs-mediatek.c b/drivers/scsi/ufs/ufs-mediatek.c
index 53eae5fe2ade2..7ac838cc15d16 100644
--- a/drivers/scsi/ufs/ufs-mediatek.c
+++ b/drivers/scsi/ufs/ufs-mediatek.c
@@ -30,6 +30,11 @@
 #define ufs_mtk_device_reset_ctrl(high, res) \
 	ufs_mtk_smc(UFS_MTK_SIP_DEVICE_RESET, high, res)
 
+#define ufs_mtk_unipro_powerdown(hba, powerdown) \
+	ufshcd_dme_set(hba, \
+		       UIC_ARG_MIB_SEL(VS_UNIPROPOWERDOWNCONTROL, 0), \
+		       powerdown)
+
 static void ufs_mtk_cfg_unipro_cg(struct ufs_hba *hba, bool enable)
 {
 	u32 tmp;
@@ -290,6 +295,8 @@ static int ufs_mtk_pre_link(struct ufs_hba *hba)
 	int ret;
 	u32 tmp;
 
+	ufs_mtk_unipro_powerdown(hba, 0);
+
 	/* disable deep stall */
 	ret = ufshcd_dme_get(hba, UIC_ARG_MIB(VS_SAVEPOWERCONTROL), &tmp);
 	if (ret)
@@ -390,9 +397,7 @@ static int ufs_mtk_link_set_hpm(struct ufs_hba *hba)
 	if (err)
 		return err;
 
-	err = ufshcd_dme_set(hba,
-			     UIC_ARG_MIB_SEL(VS_UNIPROPOWERDOWNCONTROL, 0),
-			     0);
+	err = ufs_mtk_unipro_powerdown(hba, 0);
 	if (err)
 		return err;
 
@@ -413,14 +418,10 @@ static int ufs_mtk_link_set_lpm(struct ufs_hba *hba)
 {
 	int err;
 
-	err = ufshcd_dme_set(hba,
-			     UIC_ARG_MIB_SEL(VS_UNIPROPOWERDOWNCONTROL, 0),
-			     1);
+	err = ufs_mtk_unipro_powerdown(hba, 1);
 	if (err) {
 		/* Resume UniPro state for following error recovery */
-		ufshcd_dme_set(hba,
-			       UIC_ARG_MIB_SEL(VS_UNIPROPOWERDOWNCONTROL, 0),
-			       0);
+		ufs_mtk_unipro_powerdown(hba, 0);
 		return err;
 	}
 
-- 
2.20.1