From: Manivannan Sadhasivam <mani@kernel.org>
To: Nitin Rawat <quic_nitirawa@quicinc.com>
Cc: agross@kernel.org, andersson@kernel.org,
konrad.dybcio@linaro.org, jejb@linux.ibm.com,
martin.petersen@oracle.com, quic_cang@quicinc.com,
quic_nguyenb@quicinc.com, linux-scsi@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
Subject: Re: [PATCH V5 6/6] scsi: ufs: qcom: Handle unipro clk HW division based on scaling conditions.
Date: Mon, 28 Aug 2023 13:48:37 +0530 [thread overview]
Message-ID: <20230828081837.GH5148@thinkpad> (raw)
In-Reply-To: <20230823154413.23788-7-quic_nitirawa@quicinc.com>
On Wed, Aug 23, 2023 at 09:14:13PM +0530, Nitin Rawat wrote:
> Configure internal HW division of unipro core_clk based on scale up and
> scale down condition. This bit should be cleared before entering any
> SVS mode as per hardware specification.
>
Same comment as previous patch.
- Mani
> Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
> Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com>
> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
> ---
> drivers/ufs/host/ufs-qcom.c | 49 ++++++++++++++++++++-----------------
> drivers/ufs/host/ufs-qcom.h | 2 +-
> 2 files changed, 27 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 82cf3ac4193a..d886e28b8a2a 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -95,7 +95,8 @@ static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS];
> static void ufs_qcom_get_default_testbus_cfg(struct ufs_qcom_host *host);
> static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba,
> u32 clk_cycles,
> - u32 clk_40ns_cycles);
> + u32 clk_40ns_cycles,
> + bool scale_up);
>
> static struct ufs_qcom_host *rcdev_to_ufs_host(struct reset_controller_dev *rcd)
> {
> @@ -700,19 +701,19 @@ static int ufs_qcom_cfg_core_clk_ctrl(struct ufs_hba *hba)
>
> switch (max_freq) {
> case MHZ_403:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 403, 16);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 403, 16, true);
> break;
> case MHZ_300:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 300, 12);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 300, 12, true);
> break;
> case MHZ_201_5:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 202, 8);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 202, 8, true);
> break;
> case MHZ_150:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 150, 6);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 150, 6, true);
> break;
> case MHZ_100:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, true);
> break;
> default:
> dev_err(hba->dev, "unipro max_freq=%u entry missing\n", max_freq);
> @@ -1352,7 +1353,8 @@ static void ufs_qcom_exit(struct ufs_hba *hba)
>
> static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba,
> u32 clk_1us_cycles,
> - u32 clk_40ns_cycles)
> + u32 clk_40ns_cycles,
> + bool scale_up)
> {
> struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> u32 mask = DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK;
> @@ -1378,18 +1380,20 @@ static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba,
> core_clk_ctrl_reg &= ~(mask << offset);
> core_clk_ctrl_reg |= clk_1us_cycles << offset;
>
> - /* Clear CORE_CLK_DIV_EN */
> - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT;
> + if (scale_up)
> + core_clk_ctrl_reg |= CORE_CLK_DIV_EN_BIT;
>
> err = ufshcd_dme_set(hba,
> - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL),
> - core_clk_ctrl_reg);
> + UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL),
> + core_clk_ctrl_reg);
> + if (err)
> + return err;
> /*
> * UFS host controller V4.0.0 onwards needs to program
> * PA_VS_CORE_CLK_40NS_CYCLES attribute per programmed
> * frequency of unipro core clk of UFS host controller.
> */
> - if (!err && (host->hw_ver.major >= 4)) {
> + if (host->hw_ver.major >= 4) {
> if (clk_40ns_cycles > PA_VS_CORE_CLK_40NS_CYCLES_MASK)
> return -EINVAL;
>
> @@ -1442,22 +1446,21 @@ static int ufs_qcom_clk_scale_down_pre_change(struct ufs_hba *hba)
> {
> struct ufs_qcom_host *host = ufshcd_get_variant(hba);
> int err;
> - u32 core_clk_ctrl_reg;
> + u32 reg;
>
> if (!ufs_qcom_cap_qunipro(host))
> return 0;
>
> - err = ufshcd_dme_get(hba,
> - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL),
> - &core_clk_ctrl_reg);
> + err = ufshcd_dme_get(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), ®);
> + if (err)
> + return err;
>
> /* make sure CORE_CLK_DIV_EN is cleared */
> - if (!err &&
> - (core_clk_ctrl_reg & DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT)) {
> - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT;
> + if (reg & CORE_CLK_DIV_EN_BIT) {
> + reg &= ~CORE_CLK_DIV_EN_BIT;
> err = ufshcd_dme_set(hba,
> UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL),
> - core_clk_ctrl_reg);
> + reg);
> }
>
> return err;
> @@ -1488,13 +1491,13 @@ static int ufs_qcom_clk_scale_down_post_change(struct ufs_hba *hba)
> }
> switch (curr_freq) {
> case MHZ_37_5:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 38, 2);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 38, 2, false);
> break;
> case MHZ_75:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 75, 3);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 75, 3, false);
> break;
> case MHZ_100:
> - err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4);
> + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, false);
> break;
> default:
> err = -EINVAL;
> diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h
> index 56550fd36c4e..6e8eb4bb9247 100644
> --- a/drivers/ufs/host/ufs-qcom.h
> +++ b/drivers/ufs/host/ufs-qcom.h
> @@ -140,7 +140,7 @@ enum {
> /* bit and mask definitions for DME_VS_CORE_CLK_CTRL attribute */
> #define MAX_CORE_CLK_1US_CYCLES_MASK_V4 0xFFF
> #define MAX_CORE_CLK_1US_CYCLES_OFFSET_V4 0x10
> -#define DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT BIT(8)
> +#define CORE_CLK_DIV_EN_BIT BIT(8)
> #define DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK 0xFF
> #define PA_VS_CORE_CLK_40NS_CYCLES 0x9007
> #define PA_VS_CORE_CLK_40NS_CYCLES_MASK 0x3F
> --
> 2.17.1
>
--
மணிவண்ணன் சதாசிவம்
next prev parent reply other threads:[~2023-08-28 8:20 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-23 15:44 [PATCH V5 0/6] scsi: ufs: qcom: Align programming sequence as per HW spec Nitin Rawat
2023-08-23 15:44 ` [PATCH V5 1/6] scsi: ufs: qcom: Update offset for core_clk_1us_cycles Nitin Rawat
2023-08-28 7:38 ` Manivannan Sadhasivam
2023-08-30 17:37 ` Nitin Rawat
2023-08-23 15:44 ` [PATCH V5 2/6] scsi: ufs: qcom: Configure PA_VS_CORE_CLK_40NS_CYCLES for Unipro core clk Nitin Rawat
2023-08-28 7:40 ` Manivannan Sadhasivam
2023-08-30 17:37 ` Nitin Rawat
2023-08-23 15:44 ` [PATCH V5 3/6] scsi: ufs: qcom: Add multiple frequency support for unipro clk attributes Nitin Rawat
2023-08-28 8:05 ` Manivannan Sadhasivam
2023-08-28 8:13 ` Manivannan Sadhasivam
2023-08-23 15:44 ` [PATCH V5 4/6] scsi: ufs: qcom: Align unipro clk attributes as per Hardware specification Nitin Rawat
2023-08-28 8:08 ` Manivannan Sadhasivam
2023-08-31 9:11 ` Nitin Rawat
2023-08-23 15:44 ` [PATCH V5 5/6] scsi: ufs: qcom: Refactor ufs_qcom_cfg_timers function Nitin Rawat
2023-08-28 8:17 ` Manivannan Sadhasivam
2023-08-31 9:18 ` Nitin Rawat
2023-08-23 15:44 ` [PATCH V5 6/6] scsi: ufs: qcom: Handle unipro clk HW division based on scaling conditions Nitin Rawat
2023-08-28 8:18 ` Manivannan Sadhasivam [this message]
2023-08-25 21:44 ` [PATCH V5 0/6] scsi: ufs: qcom: Align programming sequence as per HW spec Martin K. Petersen
2023-08-28 12:59 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230828081837.GH5148@thinkpad \
--to=mani@kernel.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=jejb@linux.ibm.com \
--cc=konrad.dybcio@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=martin.petersen@oracle.com \
--cc=quic_cang@quicinc.com \
--cc=quic_narepall@quicinc.com \
--cc=quic_nguyenb@quicinc.com \
--cc=quic_nitirawa@quicinc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox