From: scott worley <sworley@tht.net>
To: linux-scsi@vger.kernel.org
Subject: decoding dmesg output from aic7xxx
Date: Tue, 05 Oct 2004 08:16:09 -0400 [thread overview]
Message-ID: <41629089.4030902@tht.net> (raw)
Hi,
I have an Adaptec 39160 that has been working for the past 2 years with
a Seagate ST336938LW. I just purchased a Seagate ST336607LW and started
getting lots of messages from this new drive. It appears to be
switching between LVDS and SE mode. The new drive is on channel B of
the card and the older driver is on channel A. In the past I have used
the older drive on channel B with no problems. Also, the new driver is
connected to channel B with a unused cable that came with the card. The
other major difference is I'm running the card in a new mb, Soltek
SL-K8AN2E-GR. Had to go back to SCSI because the sata_nv driver will
not work.
The system usually will become slow to respond after being on for a
couple of hours. Once is starts responding again, the logs are full of
SCSI driver messages. Also, I am now sandwiching the new drive (in a
bag of course) between two cold bags to find out if the problem is
temperature related. This drive is a 10K rpm cheetah and does get hot.
This is my first 10k drive so I'm not sure what is normal temp.
dmesg output:
f]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
7 SCB_CONTROL[0x70]:(MK_MESSAGE|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0]
0 SCB_CONTROL[0x70]:(MK_MESSAGE|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0]
Kernel Free SCB list: 11 1 3 6 4 5 10 9 8
DevQ(0:0:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x2a 0x0 0x2 0x3b 0x75 0x6 0x0 0x0 0x10 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x2, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x3
SCSIPHASE[0x0] SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x1a]:(ENAUTOATNP|ENAUTOATNO|ENRSELI)
SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x0]
SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP)
SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) SXFRCTL0[0x80]:(DFON)
DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
STACK: 0x0 0x163 0x178 0x17
SCB count = 12
Kernel NEXTQSCB = 0
Card NEXTQSCB = 2
QINFIFO entries: 2
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 3 2 4 7 6 0 1 5 8 9 10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x70]:(MK_MESSAGE|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0]
Kernel Free SCB list: 7 11 1 3 6 4 5 10 9 8
DevQ(0:0:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x2, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x3
SCSIPHASE[0x0] SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x1a]:(ENAUTOATNP|ENAUTOATNO|ENRSELI)
SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x0]
SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP)
SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) SXFRCTL0[0x80]:(DFON)
DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
STACK: 0x0 0x163 0x178 0x17
SCB count = 12
Kernel NEXTQSCB = 2
Card NEXTQSCB = 0
QINFIFO entries: 0
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 3 2 4 7 6 0 1 5 8 9 10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
0 SCB_CONTROL[0x70]:(MK_MESSAGE|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0]
Kernel Free SCB list: 7 11 1 3 6 4 5 10 9 8
DevQ(0:0:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
scsi0:0:0:0: Attempting to queue a TARGET RESET message
CDB: 0x2a 0x0 0x2 0x3b 0x97 0xe6 0x0 0x0 0x8 0x0
scsi0:0:0:0: Command not found
aic7xxx_dev_reset returns 0x2002
scsi0:0:0:0: Attempting to queue an ABORT message
CDB: 0x0 0x0 0x0 0x0 0x0 0x0
scsi0: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State while idle, at SEQADDR 0x18
Card was paused
ACCUM = 0x2, SINDEX = 0x48, DINDEX = 0xe4, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x3
SCSIPHASE[0x0] SCSISIGI[0x0] ERROR[0x0] SCSIBUSL[0x0]
LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x1a]:(ENAUTOATNP|ENAUTOATNO|ENRSELI)
SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x0]
SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP)
SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) SXFRCTL0[0x80]:(DFON)
DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
STACK: 0x0 0x163 0x178 0x17
SCB count = 12
Kernel NEXTQSCB = 0
Card NEXTQSCB = 2
QINFIFO entries: 2
Waiting Queue entries:
Disconnected Queue entries:
QOUTFIFO entries:
Sequencer Free SCB List: 3 2 4 7 6 0 1 5 8 9 10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 28 29 30 31
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0x0] SCB_SCSIID[0x7] SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
11 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
12 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
13 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
14 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
15 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
16 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
17 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
18 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
19 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
20 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
21 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
22 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
23 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
24 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
25 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
26 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
27 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
28 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
29 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
30 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
31 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID)
SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff]
Pending list:
2 SCB_CONTROL[0x70]:(MK_MESSAGE|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0]
Kernel Free SCB list: 7 11 1 3 6 4 5 10 9 8
DevQ(0:0:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi0:0:0:0: Cmd aborted from QINFIFO
aic7xxx_abort returns 0x2002
The current dmesg with some SCSI LVD to SE mode switch messages:
This will make me look stupid, the LVD to SE mode switch is on Channel
A, the older drive. Maybe the cable on the older drive is getting old...
>896MB LOWMEM available.
found SMP MP-table at 000f55c0
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f90f0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff7b40
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: Skipping IOAPIC probe due to 'noapic' option.
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Built 1 zonelists
Kernel command line: root=/dev/sdb1 ro noapic
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2222.130 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 901828k/917504k available (1329k kernel code, 14892k reserved,
727k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4390.91 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000010
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2221.0754 MHz.
..... host bus clock speed is 201.0977 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
Freeing initrd memory: 4316k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb9b0, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc410
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc440, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 5
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:0a.1[B] -> GSI 10 (level, low) -> IRQ 10
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 4
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4316 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:0a.1[B] -> GSI 10 (level, low) -> IRQ 10
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Using anticipatory io scheduler
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: SEAGATE Model: ST336938LW Rev: 0001
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 8
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
(scsi1:A:0): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: SEAGATE Model: ST336607LW Rev: 0007
Type: Direct-Access ANSI SCSI revision: 03
scsi1:A:0:0: Tagged Queuing enabled. Depth 8
SCSI device sda: 72176567 512-byte hdwr sectors (36954 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
SGI XFS with ACLs, security attributes, realtime, large block numbers,
no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sdb1
Ending clean XFS mount for filesystem: sdb1
Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdc: DVD-ROM DDU1621, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
Capability LSM initialized
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
XFS mounting filesystem sda7
Ending clean XFS mount for filesystem: sda7
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:07.0: 3Com PCI 3c905C Tornado at 0xd000. Vers LK1.1.19
Real Time Clock Driver v1.12
input: PC Speaker
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
inserting floppy driver for 2.6.8-1-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: AGP aperture is 64M @ 0xe0000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:02.0: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 10, pci mem f890b000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 3 (level, low) -> IRQ 3
ohci_hcd 0000:00:02.1: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 3, pci mem f890d000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-1: new full speed USB device using address 2
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3
ehci_hcd 0000:00:02.2: PCI device 10de:00e8 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 3, pci mem f8934000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
usb 2-1: device not accepting address 2, error -110
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 3 (level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:06.0 to 64
ohci_hcd 0000:00:02.1: wakeup
intel8x0_measure_ac97_clock: measured 49413 usecs
intel8x0: clocking to 46813
usb 2-1: new full speed USB device using address 4
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
NFORCE3-250: port 0x0170 already claimed by ide1
usb 2-1: device not accepting address 4, error -110
usb 2-1: new full speed USB device using address 5
usb 2-1: device not accepting address 5, error -110
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11]
MMIO=[ee044000-ee0447ff] Max Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00004c0100004155]
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
NET: Registered protocol family 17
ACPI: Processor [CPU0] (supports C1)
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (0 C)
lp0: using parport0 (interrupt-driven).
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c95a0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
scsi0: Someone reset channel A
scsi0: Transceiver State Has Changed to SE mode
scsi0: Transceiver State Has Changed to LVD mode
next reply other threads:[~2004-10-05 12:15 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-10-05 12:16 scott worley [this message]
2004-10-06 17:17 ` decoding dmesg output from aic7xxx Luben Tuikov
2004-10-10 15:12 ` scott worley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=41629089.4030902@tht.net \
--to=sworley@tht.net \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).