From: Christopher Smith <csmith@nighthawkrad.net>
To: linux-scsi@vger.kernel.org
Subject: Poor write performance from Dell CERC SATA 1.5/6 controller using aacraid
Date: Tue, 07 Feb 2006 17:44:00 +1100 [thread overview]
Message-ID: <43E841B0.6080705@nighthawkrad.net> (raw)
I've got a PE750 with one of Dell's CERC SATA RAID controllers in it.
It has two 250G WD drives attached in a RAID1.
My problem is that the write performance is atrocious, at 10M/s, tops.
This is regardless of whether or not the card's write caching is enabled[0].
I have tried with both FC4 (2.6.15-1.1830_FC4smp, 2.6.14-1.1656_FC4smp,
2.6.11-1.1369_FC4smp) and CentOS 4.2/RHEL4 (2.6.9-22.0.1.ELsmp).
Performance is marginally worse with older kernels, at ~8M/s instead of
~10M/s.
Since I have another two drives of the same type in an identical
machine, only using the onboard SATA controller and software RAID that
easily pulls 30+M/s, I'm pretty sure it isn't slow drives. So I'm
wondering if it's an aacraid driver bug, or if these Dell CERC cards
just suck.
CS
[0] Indeed, enabling the write cache makes it worse, if anything, since
the system proceeds to dump as much data as possible to the cache, then
basically freeze (IO-wise) while the controller dumps the cache to disk,
then the cycle repeats. So I get about 10s of data transfer, then about
15 seconds of nothing (w/ 100% iowait), then 10s of data transfers, then
15s nothing, etc, etc. At least with the cache off, the 10M/s is pretty
much constant.
Bonnie++ results:
[root@localhost bonnie++-1.03a]# uname -r
2.6.15-1.1830_FC4smp
[root@localhost bonnie++-1.03a]# ./bonnie++ -d /tmp/ -u 0 -f -b -s 2050
[...]
Version 1.03 ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
localhost.loc 2050M 8239 3 8153 2 57685 6
190.6 0
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 47 0 +++++ +++ 56 0 73 0 +++++ +++
60 0
localhost.localdomain,2050M,,,8239,3,8153,2,,,57685,6,190.6,0,16,47,0,+++++,+++,56,0,73,0,+++++,+++,
60,0
lspci -vv:
[root@localhost bonnie++-1.03a]# lspci -vv
00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller
Hub (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=4M]
Capabilities: [e4] Vendor Specific Information
00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor to PCI to
CSA Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe200000-fe3fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Memory behind bridge: fe100000-fe1fffff
Prefetchable memory behind bridge:
00000000f4000000-00000000f7f00000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz-, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=0 Dev=28 Func=0 64bit+ 133MHz- SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=0
: Downstream: Capacity=65535, Commitment Limit=0
00:1d.0 USB Controller: Intel Corporation 6300ESB USB Universal Host
Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 201
Region 4: I/O ports at cce0 [size=32]
00:1d.1 USB Controller: Intel Corporation 6300ESB USB Universal Host
Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 209
Region 4: I/O ports at ccc0 [size=32]
00:1d.4 System peripheral: Intel Corporation 6300ESB Watchdog Timer (rev 02)
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fe400400 (32-bit, non-prefetchable) [size=16]
00:1d.5 PIC: Intel Corporation 6300ESB I/O Advanced Programmable
Interrupt Controller (rev 02) (prog-if 20 [IO(X)-APIC])
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=0 Dev=29 Func=5 64bit+ 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:1d.7 USB Controller: Intel Corporation 6300ESB USB2 Enhanced Host
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 193
Region 0: Memory at fe400000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: 40000000-400fffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.2 IDE interface: Intel Corporation 6300ESB SATA Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fea0 [size=16]
00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 6
Region 4: I/O ports at 08c0 [size=32]
01:01.0 Ethernet controller: Intel Corporation 82547GI Gigabit Ethernet
Controller
Subsystem: Dell PowerEdge 750
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: Memory at fe2e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ece0 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
02:01.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
Subsystem: Dell CERC SATA RAID 2 PCI SATA 6ch (DellCorsair)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 250ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Expansion ROM at fe100000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:02.0 Ethernet controller: Intel Corporation 82541GI/PI Gigabit
Ethernet Controller
Subsystem: Dell PowerEdge 750
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 185
Region 0: Memory at fdee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dcc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
03:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 10
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at fdedf000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 40000000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next reply other threads:[~2006-02-07 6:44 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-02-07 6:44 Christopher Smith [this message]
-- strict thread matches above, loose matches on Subject: below --
2006-02-07 15:26 Poor write performance from Dell CERC SATA 1.5/6 controller using aacraid Salyzyn, Mark
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43E841B0.6080705@nighthawkrad.net \
--to=csmith@nighthawkrad.net \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).