* Poor write performance from Dell CERC SATA 1.5/6 controller using aacraid
@ 2006-02-07 6:44 Christopher Smith
0 siblings, 0 replies; 2+ messages in thread
From: Christopher Smith @ 2006-02-07 6:44 UTC (permalink / raw)
To: linux-scsi
I've got a PE750 with one of Dell's CERC SATA RAID controllers in it.
It has two 250G WD drives attached in a RAID1.
My problem is that the write performance is atrocious, at 10M/s, tops.
This is regardless of whether or not the card's write caching is enabled[0].
I have tried with both FC4 (2.6.15-1.1830_FC4smp, 2.6.14-1.1656_FC4smp,
2.6.11-1.1369_FC4smp) and CentOS 4.2/RHEL4 (2.6.9-22.0.1.ELsmp).
Performance is marginally worse with older kernels, at ~8M/s instead of
~10M/s.
Since I have another two drives of the same type in an identical
machine, only using the onboard SATA controller and software RAID that
easily pulls 30+M/s, I'm pretty sure it isn't slow drives. So I'm
wondering if it's an aacraid driver bug, or if these Dell CERC cards
just suck.
CS
[0] Indeed, enabling the write cache makes it worse, if anything, since
the system proceeds to dump as much data as possible to the cache, then
basically freeze (IO-wise) while the controller dumps the cache to disk,
then the cycle repeats. So I get about 10s of data transfer, then about
15 seconds of nothing (w/ 100% iowait), then 10s of data transfers, then
15s nothing, etc, etc. At least with the cache off, the 10M/s is pretty
much constant.
Bonnie++ results:
[root@localhost bonnie++-1.03a]# uname -r
2.6.15-1.1830_FC4smp
[root@localhost bonnie++-1.03a]# ./bonnie++ -d /tmp/ -u 0 -f -b -s 2050
[...]
Version 1.03 ------Sequential Output------ --Sequential Input-
--Random-
-Per Chr- --Block-- -Rewrite- -Per Chr- --Block--
--Seeks--
Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
/sec %CP
localhost.loc 2050M 8239 3 8153 2 57685 6
190.6 0
------Sequential Create------ --------Random
Create--------
-Create-- --Read--- -Delete-- -Create-- --Read---
-Delete--
files /sec %CP /sec %CP /sec %CP /sec %CP /sec %CP
/sec %CP
16 47 0 +++++ +++ 56 0 73 0 +++++ +++
60 0
localhost.localdomain,2050M,,,8239,3,8153,2,,,57685,6,190.6,0,16,47,0,+++++,+++,56,0,73,0,+++++,+++,
60,0
lspci -vv:
[root@localhost bonnie++-1.03a]# lspci -vv
00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller
Hub (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=4M]
Capabilities: [e4] Vendor Specific Information
00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor to PCI to
CSA Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe200000-fe3fffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev
02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Memory behind bridge: fe100000-fe1fffff
Prefetchable memory behind bridge:
00000000f4000000-00000000f7f00000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz-, SCD-, USC-, SCO-,
SRD- Freq=0
Status: Bus=0 Dev=28 Func=0 64bit+ 133MHz- SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=0
: Downstream: Capacity=65535, Commitment Limit=0
00:1d.0 USB Controller: Intel Corporation 6300ESB USB Universal Host
Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 201
Region 4: I/O ports at cce0 [size=32]
00:1d.1 USB Controller: Intel Corporation 6300ESB USB Universal Host
Controller (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 209
Region 4: I/O ports at ccc0 [size=32]
00:1d.4 System peripheral: Intel Corporation 6300ESB Watchdog Timer (rev 02)
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fe400400 (32-bit, non-prefetchable) [size=16]
00:1d.5 PIC: Intel Corporation 6300ESB I/O Advanced Programmable
Interrupt Controller (rev 02) (prog-if 20 [IO(X)-APIC])
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [50] PCI-X non-bridge device.
Command: DPERE- ERO- RBC=0 OST=0
Status: Bus=0 Dev=29 Func=5 64bit+ 133MHz- SCD- USC-,
DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
00:1d.7 USB Controller: Intel Corporation 6300ESB USB2 Enhanced Host
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell: Unknown device 0165
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 193
Region 0: Memory at fe400000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: 40000000-400fffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.2 IDE interface: Intel Corporation 6300ESB SATA Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fea0 [size=16]
00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 6
Region 4: I/O ports at 08c0 [size=32]
01:01.0 Ethernet controller: Intel Corporation 82547GI Gigabit Ethernet
Controller
Subsystem: Dell PowerEdge 750
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 177
Region 0: Memory at fe2e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ece0 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
02:01.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
Subsystem: Dell CERC SATA RAID 2 PCI SATA 6ch (DellCorsair)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 250ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Expansion ROM at fe100000 [disabled] [size=32K]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:02.0 Ethernet controller: Intel Corporation 82541GI/PI Gigabit
Ethernet Controller
Subsystem: Dell PowerEdge 750
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63750ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 185
Region 0: Memory at fdee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dcc0 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
DC=simple, DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
03:0e.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA])
Subsystem: Dell: Unknown device 0165
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size 10
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at fdedf000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 40000000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
^ permalink raw reply [flat|nested] 2+ messages in thread
* RE: Poor write performance from Dell CERC SATA 1.5/6 controller using aacraid
@ 2006-02-07 15:26 Salyzyn, Mark
0 siblings, 0 replies; 2+ messages in thread
From: Salyzyn, Mark @ 2006-02-07 15:26 UTC (permalink / raw)
To: Christopher Smith, linux-scsi
I am getting easily 42MB/S sustained using Adaptec's 1.1.5-2400 in SLES9
using Firmware 7330 on a Dell CERC card.
Make sure you have the latest Firmware for the card and the drives.
Technical support has aacraid driver binary packaging 1.1.5-2409 on the
web site, or I can send you 1.1.5-2418 sources for you to update on your
own.
Sincerely -- Mark Salyzyn
> -----Original Message-----
> From: linux-scsi-owner@vger.kernel.org
> [mailto:linux-scsi-owner@vger.kernel.org] On Behalf Of
> Christopher Smith
> Sent: Tuesday, February 07, 2006 1:44 AM
> To: linux-scsi@vger.kernel.org
> Subject: Poor write performance from Dell CERC SATA 1.5/6
> controller using aacraid
>
>
> I've got a PE750 with one of Dell's CERC SATA RAID controllers in it.
> It has two 250G WD drives attached in a RAID1.
>
> My problem is that the write performance is atrocious, at
> 10M/s, tops.
> This is regardless of whether or not the card's write caching
> is enabled[0].
>
> I have tried with both FC4 (2.6.15-1.1830_FC4smp,
> 2.6.14-1.1656_FC4smp,
> 2.6.11-1.1369_FC4smp) and CentOS 4.2/RHEL4 (2.6.9-22.0.1.ELsmp).
> Performance is marginally worse with older kernels, at ~8M/s
> instead of
> ~10M/s.
>
> Since I have another two drives of the same type in an identical
> machine, only using the onboard SATA controller and software
> RAID that
> easily pulls 30+M/s, I'm pretty sure it isn't slow drives. So I'm
> wondering if it's an aacraid driver bug, or if these Dell CERC cards
> just suck.
>
> CS
>
> [0] Indeed, enabling the write cache makes it worse, if
> anything, since
> the system proceeds to dump as much data as possible to the
> cache, then
> basically freeze (IO-wise) while the controller dumps the
> cache to disk,
> then the cycle repeats. So I get about 10s of data transfer,
> then about
> 15 seconds of nothing (w/ 100% iowait), then 10s of data
> transfers, then
> 15s nothing, etc, etc. At least with the cache off, the
> 10M/s is pretty
> much constant.
>
>
> Bonnie++ results:
> [root@localhost bonnie++-1.03a]# uname -r
> 2.6.15-1.1830_FC4smp
> [root@localhost bonnie++-1.03a]# ./bonnie++ -d /tmp/ -u 0 -f
> -b -s 2050
> [...]
> Version 1.03 ------Sequential Output------ --Sequential Input-
> --Random-
> -Per Chr- --Block-- -Rewrite- -Per Chr-
> --Block--
> --Seeks--
> Machine Size K/sec %CP K/sec %CP K/sec %CP K/sec %CP K/sec %CP
> /sec %CP
> localhost.loc 2050M 8239 3 8153 2 57685 6
> 190.6 0
> ------Sequential Create------ --------Random
> Create--------
> -Create-- --Read--- -Delete-- -Create--
> --Read---
> -Delete--
> files /sec %CP /sec %CP /sec %CP /sec %CP
> /sec %CP
> /sec %CP
> 16 47 0 +++++ +++ 56 0 73 0
> +++++ +++
> 60 0
> localhost.localdomain,2050M,,,8239,3,8153,2,,,57685,6,190.6,0,
> 16,47,0,+++++,+++,56,0,73,0,+++++,+++,
>
> 60,0
>
> lspci -vv:
> [root@localhost bonnie++-1.03a]# lspci -vv
> 00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller
> Hub (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f8000000 (32-bit, prefetchable) [size=4M]
> Capabilities: [e4] Vendor Specific Information
>
> 00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor
> to PCI to
> CSA Bridge (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
> DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: fe200000-fe3fffff
> Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X
> Bridge (rev
> 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
> DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, Cache Line Size 10
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> Memory behind bridge: fe100000-fe1fffff
> Prefetchable memory behind bridge:
> 00000000f4000000-00000000f7f00000
> Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [50] PCI-X bridge device.
> Secondary Status: 64bit+, 133MHz-, SCD-, USC-, SCO-,
> SRD- Freq=0
> Status: Bus=0 Dev=28 Func=0 64bit+ 133MHz-
> SCD- USC-,
> SCO-, SRD-
> : Upstream: Capacity=65535, Commitment Limit=0
> : Downstream: Capacity=65535, Commitment Limit=0
>
> 00:1d.0 USB Controller: Intel Corporation 6300ESB USB Universal Host
> Controller (rev 02) (prog-if 00 [UHCI])
> Subsystem: Dell: Unknown device 0165
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 201
> Region 4: I/O ports at cce0 [size=32]
>
> 00:1d.1 USB Controller: Intel Corporation 6300ESB USB Universal Host
> Controller (rev 02) (prog-if 00 [UHCI])
> Subsystem: Dell: Unknown device 0165
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 209
> Region 4: I/O ports at ccc0 [size=32]
>
> 00:1d.4 System peripheral: Intel Corporation 6300ESB Watchdog
> Timer (rev 02)
> Subsystem: Dell: Unknown device 0165
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at fe400400 (32-bit,
> non-prefetchable) [size=16]
>
> 00:1d.5 PIC: Intel Corporation 6300ESB I/O Advanced Programmable
> Interrupt Controller (rev 02) (prog-if 20 [IO(X)-APIC])
> Subsystem: Dell: Unknown device 0165
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
> DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Capabilities: [50] PCI-X non-bridge device.
> Command: DPERE- ERO- RBC=0 OST=0
> Status: Bus=0 Dev=29 Func=5 64bit+ 133MHz-
> SCD- USC-,
> DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
>
> 00:1d.7 USB Controller: Intel Corporation 6300ESB USB2 Enhanced Host
> Controller (rev 02) (prog-if 20 [EHCI])
> Subsystem: Dell: Unknown device 0165
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 193
> Region 0: Memory at fe400000 (32-bit,
> non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Debug port
>
> 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev
> 0a) (prog-if
> 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
> DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fc000000-fdffffff
> Prefetchable memory behind bridge: 40000000-400fffff
> Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface
> Controller
> (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.2 IDE interface: Intel Corporation 6300ESB SATA Storage
> Controller
> (rev 02) (prog-if 8a [Master SecP PriP])
> Subsystem: Dell: Unknown device 0165
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 0
> Region 0: I/O ports at <unassigned>
> Region 1: I/O ports at <unassigned>
> Region 2: I/O ports at <unassigned>
> Region 3: I/O ports at <unassigned>
> Region 4: I/O ports at fea0 [size=16]
>
> 00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
> Subsystem: Dell: Unknown device 0165
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 6
> Region 4: I/O ports at 08c0 [size=32]
>
> 01:01.0 Ethernet controller: Intel Corporation 82547GI
> Gigabit Ethernet
> Controller
> Subsystem: Dell PowerEdge 750
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (63750ns min), Cache Line Size 10
> Interrupt: pin A routed to IRQ 177
> Region 0: Memory at fe2e0000 (32-bit,
> non-prefetchable) [size=128K]
> Region 2: I/O ports at ece0 [size=32]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
>
> 02:01.0 RAID bus controller: Adaptec AAC-RAID (rev 01)
> Subsystem: Dell CERC SATA RAID 2 PCI SATA 6ch (DellCorsair)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr-
> DEVSEL=slow >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (250ns min, 250ns max), Cache Line Size 10
> Interrupt: pin A routed to IRQ 169
> Region 0: Memory at f4000000 (32-bit, prefetchable)
> [size=64M]
> Expansion ROM at fe100000 [disabled] [size=32K]
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 03:02.0 Ethernet controller: Intel Corporation 82541GI/PI Gigabit
> Ethernet Controller
> Subsystem: Dell PowerEdge 750
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (63750ns min), Cache Line Size 10
> Interrupt: pin A routed to IRQ 185
> Region 0: Memory at fdee0000 (32-bit,
> non-prefetchable) [size=128K]
> Region 2: I/O ports at dcc0 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [e4] PCI-X non-bridge device.
> Command: DPERE- ERO+ RBC=0 OST=0
> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
> DC=simple, DMMRBC=2, DMOST=0, DMCRS=0, RSCEM-
>
> 03:0e.0 VGA compatible controller: ATI Technologies Inc Rage
> XL (rev 27)
> (prog-if 00 [VGA])
> Subsystem: Dell: Unknown device 0165
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+
> ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), Cache Line Size 10
> Region 0: Memory at fc000000 (32-bit,
> non-prefetchable) [size=16M]
> Region 1: I/O ports at d800 [size=256]
> Region 2: Memory at fdedf000 (32-bit,
> non-prefetchable) [size=4K]
> [virtual] Expansion ROM at 40000000 [disabled] [size=128K]
> Capabilities: [5c] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> -
> To unsubscribe from this list: send the line "unsubscribe
> linux-scsi" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2006-02-07 15:26 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-02-07 6:44 Poor write performance from Dell CERC SATA 1.5/6 controller using aacraid Christopher Smith
-- strict thread matches above, loose matches on Subject: below --
2006-02-07 15:26 Salyzyn, Mark
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).