From: Maxim Kozover <maximkoz@netvision.net.il>
To: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Stefan Kaltenbrunner <mm-mailinglist@madness.at>,
Andrew Morton <akpm@osdl.org>,
linux-kernel@vger.kernel.org, linux-scsi@vger.kernel.org
Subject: Re:Re: problems with scsi_transport_fc and qla2xxx
Date: Thu, 02 Mar 2006 19:32:48 +0300 [thread overview]
Message-ID: <957728045.20060302193248@netvision.net.il> (raw)
In-Reply-To: <20060301210802.GA7288@spe2>
Hi Andrew!
Today I tested disconnecting QLogic port.
Adapter 4 is connected via switch to a storage and 3 LUNs are seen via
the adapter.
Only 1 rport is created (for FCP Target) while in Emulex case there
were 3: (Fabric Port, Directory Server and FCP Target, FCP Initiator).
# ls /sys/class/fc_remote_ports/
rport-4:0-0
# cat /sys/class/fc_remote_ports/*/roles
FCP Target
Default dev_loss_tmo is 6 (1+5) while in Emulex case the default was 35.
After disconnecting the cable between the HBA and the switch
qla2xxx 0000:03:01.0: LOOP DOWN detected (2).
rport-4:0-0: blocked FC remote port time out: removing target and saving binding
# ls /sys/class/fc_remote_ports/
rport-4:0-0
# cat /sys/class/fc_remote_ports/*/roles
unknown
Relevant scsi devices are removed from /proc/scsi/scsi.
After reconnecting the cable
qla2xxx 0000:03:01.0: LIP reset occured (f7f7).
qla2xxx 0000:03:01.0: LOOP UP detected (2 Gbps).
# ls /sys/class/fc_remote_ports/
rport-4:0-0
# cat /sys/class/fc_remote_ports/*/roles
FCP Target
However, scsi devices don't reappear in /proc/scsi/scsi.
When I issue rescan, the command is stuck
echo - - - > /sys/class/scsi_host/host4/scan
Please advise.
Thanks,
Maxim.
I'm including /var/log/messages output:
# egrep -v 'Vendor|cron' /var/log/messages
Mar 2 19:13:49 multipath kernel: QLogic Fibre Channel HBA Driver
Mar 2 19:13:49 multipath kernel: GSI 24 sharing vector 0xE9 and IRQ 24
Mar 2 19:13:49 multipath kernel: ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 48 (level, low) -> IRQ 233
Mar 2 19:13:49 multipath kernel: qla2xxx 0000:03:01.0: Found an ISP2312, irq 233, iobase 0xffffc20000004000
Mar 2 19:13:49 multipath kernel: qla2xxx 0000:03:01.0: Configuring PCI space...
Mar 2 19:13:49 multipath kernel: qla2xxx 0000:03:01.0: Configure NVRAM parameters...
Mar 2 19:13:49 multipath kernel: qla2xxx 0000:03:01.0: Verifying loaded RISC code...
Mar 2 19:13:49 multipath kernel: qla2xxx 0000:03:01.0: Waiting for LIP to complete...
Mar 2 19:13:51 multipath kernel: qla2xxx 0000:03:01.0: LIP reset occured (f7f7).
Mar 2 19:13:51 multipath kernel: qla2xxx 0000:03:01.0: LOOP UP detected (2 Gbps).
Mar 2 19:13:51 multipath kernel: qla2xxx 0000:03:01.0: Topology - (F_Port), Host Loop address 0xffff
Mar 2 19:13:52 multipath kernel: scsi4 : qla2xxx
Mar 2 19:13:52 multipath kernel: qla2xxx 0000:03:01.0:
Mar 2 19:13:52 multipath kernel: QLogic Fibre Channel HBA Driver: 8.01.04-k
Mar 2 19:13:52 multipath kernel: QLogic QLA2340 -
Mar 2 19:13:52 multipath kernel: ISP2312: PCI-X (133 MHz) @ 0000:03:01.0 hdma-, host#=4, fw=3.03.18 IPX
Mar 2 19:13:52 multipath kernel: GSI 25 sharing vector 0x32 and IRQ 25
Mar 2 19:13:52 multipath kernel: ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 72 (level, low) -> IRQ 50
Mar 2 19:13:52 multipath kernel: qla2xxx 0000:06:01.0: Configuring PCI space...
Mar 2 19:13:52 multipath kernel: qla2xxx 0000:06:01.0: Configure NVRAM parameters...
Mar 2 19:13:52 multipath kernel: Type: Direct-Access ANSI SCSI revision: 05
Mar 2 19:13:52 multipath kernel: SCSI device sdb: 33554432 512-byte hdwr sectors (17180 MB)
Mar 2 19:13:52 multipath kernel: sdb: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdb: drive cache: write through
Mar 2 19:13:52 multipath kernel: SCSI device sdb: 33554432 512-byte hdwr sectors (17180 MB)
Mar 2 19:13:52 multipath kernel: sdb: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdb: drive cache: write through
Mar 2 19:13:52 multipath kernel: sdb: unknown partition table
Mar 2 19:13:52 multipath kernel: sd 4:0:0:0: Attached scsi disk sdb
Mar 2 19:13:52 multipath kernel: qla2xxx 0000:06:01.0: Verifying loaded RISC code...
Mar 2 19:13:52 multipath kernel: Type: Direct-Access ANSI SCSI revision: 05
Mar 2 19:13:52 multipath scsi.agent[4288]: disk at /devices/pci0000:00/0000:00:02.0/0000:01:00.2/0000:03:01.0/host4/rport-4:0-0/target4:0:0/4:0:0:0
Mar 2 19:13:52 multipath kernel: SCSI device sdc: 67108864 512-byte hdwr sectors (34360 MB)
Mar 2 19:13:52 multipath kernel: sdc: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdc: drive cache: write through
Mar 2 19:13:52 multipath kernel: SCSI device sdc: 67108864 512-byte hdwr sectors (34360 MB)
Mar 2 19:13:52 multipath kernel: sdc: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdc: drive cache: write through
Mar 2 19:13:52 multipath kernel: sdc: unknown partition table
Mar 2 19:13:52 multipath kernel: sd 4:0:0:1: Attached scsi disk sdc
Mar 2 19:13:52 multipath kernel: Type: Direct-Access ANSI SCSI revision: 05
Mar 2 19:13:52 multipath kernel: sdd : very big device. try to use READ CAPACITY(16).
Mar 2 19:13:52 multipath kernel: SCSI device sdd: 9797894144 512-byte hdwr sectors (5016522 MB)
Mar 2 19:13:52 multipath kernel: sdd: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdd: drive cache: write through
Mar 2 19:13:52 multipath kernel: sdd : very big device. try to use READ CAPACITY(16).
Mar 2 19:13:52 multipath kernel: SCSI device sdd: 9797894144 512-byte hdwr sectors (5016522 MB)
Mar 2 19:13:52 multipath kernel: sdd: Write Protect is off
Mar 2 19:13:52 multipath kernel: SCSI device sdd: drive cache: write through
Mar 2 19:13:52 multipath scsi.agent[4313]: disk at /devices/pci0000:00/0000:00:02.0/0000:01:00.2/0000:03:01.0/host4/rport-4:0-0/target4:0:0/4:0:0:1
Mar 2 19:13:52 multipath kernel: sdd: unknown partition table
Mar 2 19:13:52 multipath kernel: sd 4:0:0:2: Attached scsi disk sdd
Mar 2 19:13:52 multipath scsi.agent[4331]: disk at /devices/pci0000:00/0000:00:02.0/0000:01:00.2/0000:03:01.0/host4/rport-4:0-0/target4:0:0/4:0:0:2
Mar 2 19:13:52 multipath kernel: qla2xxx 0000:06:01.0: Waiting for LIP to complete...
Mar 2 19:14:12 multipath kernel: qla2xxx 0000:06:01.0: Cable is unplugged...
Mar 2 19:14:12 multipath kernel: scsi5 : qla2xxx
Mar 2 19:14:12 multipath kernel: qla2xxx 0000:06:01.0:
Mar 2 19:14:12 multipath kernel: QLogic Fibre Channel HBA Driver: 8.01.04-k
Mar 2 19:14:12 multipath kernel: QLogic QLA2340 -
Mar 2 19:14:12 multipath kernel: ISP2312: PCI-X (133 MHz) @ 0000:06:01.0 hdma-, host#=5, fw=3.03.18 IPX
Mar 2 19:14:17 multipath kernel: qla2xxx 0000:06:01.0: Unable to retrieve host statistics (65535).
Mar 2 19:14:18 multipath last message repeated 19 times
Mar 2 19:22:02 multipath kernel: qla2xxx 0000:03:01.0: LOOP DOWN detected (2).
Mar 2 19:22:08 multipath kernel: rport-4:0-0: blocked FC remote port time out: removing target and saving binding
Mar 2 19:24:04 multipath kernel: qla2xxx 0000:03:01.0: LIP reset occured (f7f7).
Mar 2 19:24:04 multipath kernel: qla2xxx 0000:03:01.0: LOOP UP detected (2 Gbps).
next prev parent reply other threads:[~2006-03-02 17:32 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1413265398.20060227150526@netvision.net.il>
[not found] ` <978150825.20060227210552@netvision.net.il>
2006-03-01 6:14 ` problems with scsi_transport_fc and qla2xxx Andrew Morton
2006-03-01 20:25 ` Stefan Kaltenbrunner
2006-03-01 21:08 ` Andrew Vasquez
2006-03-02 16:32 ` Maxim Kozover [this message]
2006-03-02 17:38 ` Andrew Vasquez
2006-03-02 22:15 ` Maxim Kozover
2006-03-06 19:06 ` Andrew Vasquez
2006-03-06 20:00 ` Mike Snitzer
2006-03-06 20:09 ` Maxim Kozover
2006-03-06 21:28 ` Andrew Vasquez
2006-03-06 20:57 ` Maxim Kozover
2006-03-06 21:09 ` Maxim Kozover
[not found] ` <20060306232831.GS6278@andrew-vasquezs-powerbook-g4-15.local>
[not found] ` <1219491790.20060307124035@netvision.net.il>
[not found] ` <20060307172227.GE6275@andrew-vasquezs-powerbook-g4-15.local>
[not found] ` <1343850424.20060307231141@netvision.net.il>
[not found] ` <20060308080050.GF9956@andrew-vasquezs-powerbook-g4-15.local>
[not found] ` <20060308154341.GA1779@andrew-vasquezs-powerbook-g4-15.local>
[not found] ` <1502511597.20060308213247@netvision.net.il>
[not found] ` <20060310231344.GB641@andrew-vasquezs-powerbook-g4-15.local>
2006-03-11 21:10 ` Re[8]: " Maxim Kozover
2006-03-12 9:28 ` Arjan van de Ven
2006-03-12 11:46 ` Maxim Kozover
2006-03-13 23:19 ` Andrew Vasquez
2006-03-20 10:45 ` Maxim Kozover
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=957728045.20060302193248@netvision.net.il \
--to=maximkoz@netvision.net.il \
--cc=akpm@osdl.org \
--cc=andrew.vasquez@qlogic.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=mm-mailinglist@madness.at \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).