Re: [PATCH v5 2/4] soc: qcom: ice: Add OPP-based clock scaling support for ICE

[Abhinaba Rakshit <abhinaba.rakshit@oss.qualcomm.com>]

On Mon, Feb 16, 2026 at 01:18:57PM +0100, Konrad Dybcio wrote:
> On 2/13/26 8:02 AM, Abhinaba Rakshit wrote:
> > On Thu, Feb 12, 2026 at 12:30:00PM +0100, Konrad Dybcio wrote:
> >> On 2/11/26 10:47 AM, Abhinaba Rakshit wrote:
> >>> Register optional operation-points-v2 table for ICE device
> >>> and aquire its minimum and maximum frequency during ICE
> >>> device probe.
> 
> [...]
> 
> >>> +	if (!ice->has_opp)
> >>> +		return -EOPNOTSUPP;
> >>> +
> >>> +	/* Clamp the freq to max if target_freq is beyond supported frequencies */
> >>> +	if (ice->max_freq && target_freq >= ice->max_freq) {
> >>> +		ice_freq = ice->max_freq;
> >>> +		goto scale_clock;
> >>> +	}
> >>> +
> >>> +	/* Clamp the freq to min if target_freq is below supported frequencies */
> >>> +	if (ice->min_freq && target_freq <= ice->min_freq) {
> >>> +		ice_freq = ice->min_freq;
> >>> +		goto scale_clock;
> >>> +	}
> >>
> >> The OPP framework won't let you overclock the ICE if this is what these checks
> >> are about. Plus the clk framework will perform rounding for you too
> > 
> > Right, maybe I can just add a check for 0 freq just to ensure the export API is
> > not miss used.
> > Something shown below:
> > 
> > if (!target_freq)
> >     return -EINVAL;
> > 
> > However, my main concern was for the corner cases, where:
> > (target_freq > max && ROUND_CEIL)
> > and
> > (target_freq < min && ROUND_FLOOR)
> > In both the cases, the OPP APIs will fail and the clock remains unchanged.
> 
> I would argue that's expected behavior, if the requested rate can not
> be achieved, the "set_rate"-like function should fail
> 
> > Hence, I added the checks to make the API as generic/robust as possible.
> 
> AFAICT we generally set storage_ctrl_rate == ice_clk_rate with some slight
> play, but the latter never goes above the FMAX of the former
> 
> For the second case, I'm not sure it's valid. For "find lowest rate" I would
> expect find_freq_*ceil*(rate=0). For other cases of scale-down I would expect
> that we want to keep the clock at >= (or ideally == )storage_ctrl_clk anyway
> so I'm not sure _floor() is useful

Clear, I guess, the idea is to ensure ice-clk <= storage-clk in case of scale_up
and ice-clk >= storage-clk in case of scale_down.

Best would be to use, _floor for scale_up and _ceil for scale_down.
 
> > 
> > Please let me know, your thoughts.
> > 
> >>> +
> >>> +	switch (flags) {
> >>
> >> Are you going to use these flags? Currently they're dead code
> > 
> > I agree, currently they are not used.
> > However, since its an export API, I want to keep the rounding FLAGS
> > support as it a common to have rounding flags in clock scaling APIs,
> > and to support any future use-cases as well.
> 
> I think you have a bit of a misconception - yes, this is an export API and
> should be designed with the consumers in mind, but then it's consumed by
> in-tree modules only ("what's not on the list doesn't exist"), so it's actually
> generally *discouraged* (with varying levels of emphasis) to add any code that
> is not immediately useful, as these functions can be updated at any point in
> time down the line

Sure, understood
Will make sure to update in next patchset and make use of rounding flags.

Abhinaba Rakshit