From: bugzilla-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 151661] Adaptec 3805 prints "AAC: Host adapter dead -1" every 10 seconds but works fine anyway
Date: Fri, 12 Aug 2016 05:42:22 +0000 [thread overview]
Message-ID: <bug-151661-11613-ndEO8WtLVx@https.bugzilla.kernel.org/> (raw)
In-Reply-To: <bug-151661-11613@https.bugzilla.kernel.org/>
https://bugzilla.kernel.org/show_bug.cgi?id=151661
Chris "SKip" Mac-Stoker <chrismac@niksun.com> changed:
What |Removed |Added
----------------------------------------------------------------------------
CC| |chrismac@niksun.com
--- Comment #4 from Chris "SKip" Mac-Stoker <chrismac@niksun.com> ---
.. just created an account and wanted to post a confirmation of this bug, on a
chassis with this controller, the "AAC: Host Adapter Dead -1" did not appear at
all on an Ubuntu 14.04.1 installation (OS installed, not Live USB), but
suddenly showed up after a fresh installation of 16.04 (amd64) on the same
chassis and persists just like the OP says, every 10s. Otherwise the controller
works normally with a RAID5 4-disk array with no noticeable performance
degradation as tested with hdparm -T.
Copying here the relevant lspci -vv stub in case it helps:
---(cut here)---
02:0e.0 RAID bus controller: Adaptec AAC-RAID
Subsystem: Adaptec 3805
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e8000000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=4
Status: Dev=02:0e.0 64bit+ 133MHz+ SCD- USC- DC=bridge
DMMRBC=1024 DMOST=4 DMCRS=16 RSCEM- 266MHz- 533MHz-
Kernel driver in use: aacraid
Kernel modules: aacraid
--
You are receiving this mail because:
You are watching the assignee of the bug.
next prev parent reply other threads:[~2016-08-12 5:43 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-06 21:47 [Bug 151661] New: Adaptec 3805 prints "AAC: Host adapter dead -1" every 10 seconds but works fine anyway bugzilla-daemon
2016-08-11 15:53 ` [Bug 151661] " bugzilla-daemon
2016-08-11 15:54 ` bugzilla-daemon
2016-08-11 15:55 ` bugzilla-daemon
2016-08-12 5:42 ` bugzilla-daemon [this message]
2016-08-12 6:17 ` bugzilla-daemon
2016-08-14 22:39 ` bugzilla-daemon
2016-08-15 7:17 ` bugzilla-daemon
2016-08-17 18:43 ` bugzilla-daemon
2016-08-18 21:15 ` [Bug 151661] Adaptec 3405 " bugzilla-daemon
2016-08-22 21:52 ` bugzilla-daemon
2016-08-22 21:54 ` bugzilla-daemon
2016-08-22 21:54 ` bugzilla-daemon
2016-09-04 11:25 ` bugzilla-daemon
2016-09-14 10:09 ` bugzilla-daemon
2016-09-14 10:18 ` bugzilla-daemon
2016-09-14 10:20 ` bugzilla-daemon
2016-09-14 10:22 ` bugzilla-daemon
2016-10-03 20:45 ` bugzilla-daemon
2017-01-15 11:10 ` bugzilla-daemon
2017-02-10 9:23 ` bugzilla-daemon
2017-06-21 22:43 ` bugzilla-daemon
2018-01-06 16:02 ` bugzilla-daemon
2018-01-08 17:44 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bug-151661-11613-ndEO8WtLVx@https.bugzilla.kernel.org/ \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox