From: bugzilla-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 85101] hpsa + P410 does not show connected HP SAS port expanders
Date: Wed, 24 Sep 2014 21:33:38 +0000 [thread overview]
Message-ID: <bug-85101-11613-AaLrfiEiSd@https.bugzilla.kernel.org/> (raw)
In-Reply-To: <bug-85101-11613@https.bugzilla.kernel.org/>
https://bugzilla.kernel.org/show_bug.cgi?id=85101
--- Comment #2 from linux-ide@crashplan.pro ---
In this case the hardware seems broken.
The P410 controller is only used for upgrading the HP SAS expander firmware.
This time we started with upgrading the controller firmware:
===
./ccissflash
This program consists of two phases: device discovery and device update.
No device will be updated until you answer.
Do you want to run device discovery?
(yes/no) yes
Finding hardware. This may take a few minutes.
Found 1 devices.
Do you want to upgrade the device that has older ROM?
(yes/no) yes
1 devices will be updated.
Updating: P410 Slot: 2 from [5.70] to [6.60]
Updating: P410 Slot: 2 from [5.70] to [6.60]
As part of the reboot process, you must power cycle the server and any external
array storage devices.
===
After power cycling the first three reboots were ok. Then a controller lockup
0x00130000 occurred 468 seconds after loading the hpsa module. Since then only
one boot/module loading was ok and since then the "time outs" are occurring:
===
[ 121.613269] HP HPSA Driver (v 3.4.0-1)
[ 121.613344] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 121.613447] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 121.613669] hpsa 0000:01:00.0: MSIX
[ 121.613770] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 121.613843] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 121.613909] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 121.613981] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 121.614046] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 121.614117] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 121.614182] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 121.614251] hpsa 0000:01:00.0: irq 53 for MSI/MSI-X
[ 121.634560] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 46 using DAC
[ 127.171906] scsi4 : hpsa
[ 127.174883] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 127.175961] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
[ 127.176335] scsi 4:3:0:0: Attached scsi generic sg1 type 12
[ 424.473998] HP HPSA Driver (v 3.4.0-1)
===
[ 16.127857] HP HPSA Driver (v 3.4.0-1)
[ 16.127927] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 16.128020] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 16.128231] hpsa 0000:01:00.0: MSIX
[ 16.128327] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 16.128394] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 16.128460] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 16.128524] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 16.128590] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 16.128660] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 16.128726] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 16.128791] hpsa 0000:01:00.0: irq 53 for MSI/MSI-X
[ 16.149110] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 46 using DAC
[ 34.767566] scsi4 : hpsa
[ 34.770583] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 34.771054] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 48.389920] HP HPSA Driver (v 3.4.4-1)
[ 48.389985] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 48.390059] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 48.390239] hpsa 0000:01:00.0: MSIX
[ 48.390312] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 48.390362] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 48.390453] hpsa 0000:01:00.0: Logical aborts not supported
[ 48.410617] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 53.947809] scsi host4: hpsa
[ 53.953488] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 53.953986] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 17.076307] HP HPSA Driver (v 3.4.4-1)
[ 17.076388] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 17.076483] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 17.076695] hpsa 0000:01:00.0: MSIX
[ 17.076782] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 17.076837] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 17.076942] hpsa 0000:01:00.0: Logical aborts not supported
[ 17.097108] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 33.659110] scsi host4: hpsa
[ 33.663958] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 33.664360] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
[ 33.665053] scsi 4:3:0:0: Attached scsi generic sg1 type 12
[ 485.066696] hpsa 0000:01:00.0: Controller lockup detected: 0x00130000
===
[ 49.567169] HP HPSA Driver (v 3.4.4-1)
[ 49.567251] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 49.567389] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 49.567576] hpsa 0000:01:00.0: MSIX
[ 49.567649] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 49.567705] hpsa 0000:01:00.0: irq 31 for MSI/MSI-X
[ 49.567799] hpsa 0000:01:00.0: Logical aborts not supported
[ 49.587966] hpsa 0000:01:00.0: hpsa0: <0x323a> at IRQ 30 using DAC
[ 55.125143] scsi host4: hpsa
[ 55.129439] hpsa 0000:01:00.0: RAID device c4b3t0l0 added.
[ 55.129832] scsi 4:3:0:0: RAID HP P410 6.60
PQ: 0 ANSI: 5
===
[ 38.305788] HP HPSA Driver (v 3.4.4-1)
[ 38.305854] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 38.306052] hpsa 0000:01:00.0: MSIX
[ 38.306127] hpsa 0000:01:00.0: irq 29 for MSI/MSI-X
[ 38.306179] hpsa 0000:01:00.0: irq 30 for MSI/MSI-X
[ 163.163631] hpsa 0000:01:00.0: board not ready, timed out.
===
[ 23.324890] HP HPSA Driver (v 3.4.0-1)
[ 23.324957] hpsa 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM
control
[ 23.325060] hpsa 0000:01:00.0: enabling device (0000 -> 0003)
[ 23.325281] hpsa 0000:01:00.0: MSIX
[ 23.325379] hpsa 0000:01:00.0: irq 45 for MSI/MSI-X
[ 23.325453] hpsa 0000:01:00.0: irq 46 for MSI/MSI-X
[ 23.325518] hpsa 0000:01:00.0: irq 47 for MSI/MSI-X
[ 23.325591] hpsa 0000:01:00.0: irq 48 for MSI/MSI-X
[ 23.325655] hpsa 0000:01:00.0: irq 49 for MSI/MSI-X
[ 23.325728] hpsa 0000:01:00.0: irq 50 for MSI/MSI-X
[ 23.325793] hpsa 0000:01:00.0: irq 51 for MSI/MSI-X
[ 23.325865] hpsa 0000:01:00.0: irq 52 for MSI/MSI-X
[ 148.185212] hpsa 0000:01:00.0: board not ready, timed out.
===
Right now loading the hpsa module permanently errors out with "board not ready,
timed out" and the "DS1: Diagnostics Error" LED turns Amber (=One of the server
diagnostics utilities has detected a controller error.)
Seems like a hardware issue, therefore this case can be closed.
--
You are receiving this mail because:
You are watching the assignee of the bug.
next prev parent reply other threads:[~2014-09-24 21:33 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-09-24 16:46 [Bug 85101] New: hpsa + P410 does not show connected HP SAS port expanders bugzilla-daemon
2014-09-24 18:22 ` [Bug 85101] " bugzilla-daemon
2014-09-24 21:33 ` bugzilla-daemon [this message]
2014-09-24 22:32 ` bugzilla-daemon
2014-09-25 10:48 ` bugzilla-daemon
2014-09-25 10:49 ` bugzilla-daemon
2014-09-25 14:05 ` bugzilla-daemon
2014-09-25 22:22 ` bugzilla-daemon
2014-09-25 22:35 ` bugzilla-daemon
2014-09-25 22:42 ` bugzilla-daemon
2014-10-01 21:59 ` bugzilla-daemon
2023-11-08 9:42 ` bugzilla-daemon
2025-09-18 9:57 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=bug-85101-11613-AaLrfiEiSd@https.bugzilla.kernel.org/ \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).