Re: serial flow control appears broken

Re: serial flow control appears broken

[Robert Hancock]

Lee Howard wrote:
> Hello.
> 
> I have fax modems that will, in their proper behavior with certain 
> features, send up to 64 kilobytes of data to the host DTE all at once.  
> (So, the fax modem handles an incoming fax and periodically will send 
> between 256 bytes and 64 kilobytes of data in bursts.)
> 
> When the DCE-DTE (modem-to-host) communication rate is established at 
> 115200 bps data loss occurs systems using at least Linux kernels 2.6.5 
> and 2.6.18 (and probably everything in-beween and then some more).  This 
> is because the modem overflows the host's buffer.  This is evidenced in 
> kernel logging:
> 
> Jul 23 14:01:30 gollum kernel: ttyS1: 1 input overrun(s)
> Jul 23 17:09:45 gollum kernel: ttyS1: 1 input overrun(s)
> 
> Normally I would blame the modem itself for not honoring the host's flow 
> control signals.  However, I have worked with the modem manufacturer 
> closely on this matter for over three months now.  In that process they 
> have improved the responsiveness of the modem and have fixed other 
> problems, but the end result is that it truly does appear that the 
> serial tty driver is not using flow control.  Whether software flow 
> control (XON/XOFF) or hardware flow control (RTS/CTS) is used the result 
> is the same.
> 
> This is evidenced in hardware flow control by a little LED labeled "RTS" 
> that is on the external modem.  This LED lights up when pin 7 of the DB9 
> serial connection is given +12Vdc current (signalling "RTS" is on - that 
> the host can accept data).  The LED goes dark when the current is 
> removed (signalling that the host cannot accept data).  This "RTS" LED 
> never flickers at all, as it should, when receiving these bursts of data 
> - the LED stays lit as long as the serial cable is connected to the 
> host... and yet I will see those "input overrun" messages.  Thus, it 
> seems quite clear that the Linux serial tty driver is not deasserting 
> RTS as it should in hardware flow control.  (And probably the analogous 
> problem exists in software flow control, too.)
> 
> Please tell me what I can do to help you resove and/or remedy this 
> matter.  Also, please let me know if I have contacted the wrong people.  
> (I have cross-posted to linux-kernel as a catch-all.  I am not 
> subscribed to either linux-serial or linux-kernel mailing lists.  So 
> please CC me in any list responses.)
> 
> If it is of any value to know (perhaps they have common code?), the same 
> error occurs on FreeBSD 6.2 as well.   The problem does not occur on 
> Windows.  The problem does not occur on RedHat 6.0 (kernel 2.2.5).

What kind of serial port and machine is this on? From what I can see, a 
standard 16550 UART (not a special variant) just doesn't have any 
support for clearing RTS on its own when its input FIFO gets too full. 
The kernel would have to do it in that case. I'm not seeing where it 
would be controlling that automatically (as opposed to manually from the 
application with TIOCM_RTS). I'm also not sure if the UART gives the 
kernel enough information for it to even be able to control this line 
properly automatically.

That's assuming it actually is a 16550 or similar with a 16-byte FIFO at 
all, which assuming it's a non-ancient PC it should be, but who knows.

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/

Re: serial flow control appears broken

[Lee Howard]

Robert Hancock wrote:

> Lee Howard wrote:
>
>> Hello.
>>
>> I have fax modems that will, in their proper behavior with certain 
>> features, send up to 64 kilobytes of data to the host DTE all at 
>> once.  (So, the fax modem handles an incoming fax and periodically 
>> will send between 256 bytes and 64 kilobytes of data in bursts.)
>>
>> When the DCE-DTE (modem-to-host) communication rate is established at 
>> 115200 bps data loss occurs systems using at least Linux kernels 
>> 2.6.5 and 2.6.18 (and probably everything in-beween and then some 
>> more).  This is because the modem overflows the host's buffer.  This 
>> is evidenced in kernel logging:
>>
>> Jul 23 14:01:30 gollum kernel: ttyS1: 1 input overrun(s)
>> Jul 23 17:09:45 gollum kernel: ttyS1: 1 input overrun(s)
>>
>> Normally I would blame the modem itself for not honoring the host's 
>> flow control signals.  However, I have worked with the modem 
>> manufacturer closely on this matter for over three months now.  In 
>> that process they have improved the responsiveness of the modem and 
>> have fixed other problems, but the end result is that it truly does 
>> appear that the serial tty driver is not using flow control.  Whether 
>> software flow control (XON/XOFF) or hardware flow control (RTS/CTS) 
>> is used the result is the same.
>>
>> This is evidenced in hardware flow control by a little LED labeled 
>> "RTS" that is on the external modem.  This LED lights up when pin 7 
>> of the DB9 serial connection is given +12Vdc current (signalling 
>> "RTS" is on - that the host can accept data).  The LED goes dark when 
>> the current is removed (signalling that the host cannot accept 
>> data).  This "RTS" LED never flickers at all, as it should, when 
>> receiving these bursts of data - the LED stays lit as long as the 
>> serial cable is connected to the host... and yet I will see those 
>> "input overrun" messages.  Thus, it seems quite clear that the Linux 
>> serial tty driver is not deasserting RTS as it should in hardware 
>> flow control.  (And probably the analogous problem exists in software 
>> flow control, too.)
>>
>> Please tell me what I can do to help you resove and/or remedy this 
>> matter.  Also, please let me know if I have contacted the wrong 
>> people.  (I have cross-posted to linux-kernel as a catch-all.  I am 
>> not subscribed to either linux-serial or linux-kernel mailing lists.  
>> So please CC me in any list responses.)
>>
>> If it is of any value to know (perhaps they have common code?), the 
>> same error occurs on FreeBSD 6.2 as well.   The problem does not 
>> occur on Windows.  The problem does not occur on RedHat 6.0 (kernel 
>> 2.2.5).
>
>
> What kind of serial port and machine is this on? From what I can see, 
> a standard 16550 UART (not a special variant) just doesn't have any 
> support for clearing RTS on its own when its input FIFO gets too full. 
> The kernel would have to do it in that case. I'm not seeing where it 
> would be controlling that automatically (as opposed to manually from 
> the application with TIOCM_RTS). I'm also not sure if the UART gives 
> the kernel enough information for it to even be able to control this 
> line properly automatically.
>
> That's assuming it actually is a 16550 or similar with a 16-byte FIFO 
> at all, which assuming it's a non-ancient PC it should be, but who knows.


Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

It's a Shuttle HOT-661 motherboard (VIA Apollo Pro Plus mainboard 
chipset).  Both FreeBSD and Linux identify the serial chipset type as 
16550A.

If the application were to use TIOCM_RTS how would it know when to apply 
it or not?  Is there some approach that the application could take to 
manage flow control on the serial port?  What about software flow 
control?  Does the application (and not the driver) need to be managing 
the DC1/DC3 signalling on the host-side?

Thanks,

Lee.

Re: serial flow control appears broken

[Alan Cox]

> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> 
> It's a Shuttle HOT-661 motherboard (VIA Apollo Pro Plus mainboard 
> chipset).  Both FreeBSD and Linux identify the serial chipset type as 
> 16550A.

So you've got 16bytes of buffering. That ought to be enough on a modern
PC. The older kernels use quite limited internal buffers which may be a
factor, the current ones have a rewritten tty buffering layer which may
improve matters enormously.

Alan

Re: serial flow control appears broken

[Lee Howard]

Alan Cox wrote:

>>Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
>>ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>>ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
>>
>>It's a Shuttle HOT-661 motherboard (VIA Apollo Pro Plus mainboard 
>>chipset).  Both FreeBSD and Linux identify the serial chipset type as 
>>16550A.
>>    
>>
>
>So you've got 16bytes of buffering. That ought to be enough on a modern
>PC. The older kernels use quite limited internal buffers which may be a
>factor, the current ones have a rewritten tty buffering layer which may
>improve matters enormously.
>

So, does this explain why I wouldn't have a problem at 115200 bps with 
kernel 2.2.5 but why I do with 2.6.5 and 2.6.18?  Both hardware and 
software flow control work fine with 2.2.5 (meaning I don't see any 
error message and I don't have any data corruption), but neither works 
to avoid the "kernel: ttyS1: 1 input overrun(s)" and consequent data 
corruption issue in 2.6.5 nor 2.6.18.

Was there some associated application change in tty handling that needed 
to occur between the 2.2 and 2.6 kernels to properly implement flow control?

Thanks,

Lee.

Re: serial flow control appears broken

[Alan Cox]

> So, does this explain why I wouldn't have a problem at 115200 bps with 
> kernel 2.2.5 but why I do with 2.6.5 and 2.6.18?  Both hardware and 

Without a scope on the board running both 2.2 and 2.6 that would be hard
to tell.

> Was there some associated application change in tty handling that needed 
> to occur between the 2.2 and 2.6 kernels to properly implement flow control?

Can we do this in a sensible, logical diagnostic order please. You are
making assumptions that seem unwise - eg that the code didn't happen to
work in 2.2.5 even though it was not correctly setting hardware flow
control, or that the defaults set by the user space apps run with the
distribution haven't changed and thus shown up such a problem.

Also was the 2.2 and 2.6 on the same exact mainboard ?

You've verified that flow control does not seem to be getting asserted
for h/w control on the wires

Next question on the software side therefore is does the serial port have
CRTSCTS set when the problem is showing up. (stty -a </dev/ttyWhatever)

Re: serial flow control appears broken

[Lee Howard]

Alan Cox wrote:

>>So, does this explain why I wouldn't have a problem at 115200 bps with 
>>kernel 2.2.5 but why I do with 2.6.5 and 2.6.18?  Both hardware and 
>>    
>>
>
>Without a scope on the board running both 2.2 and 2.6 that would be hard
>to tell.
>  
>

I see.  Unfortunately I don't have a scope here in my office.  The modem 
manufacturer does have a scope, but they only have a system running 
2.6.  I suppose I could have them return the test system that I sent to 
them and I could reinstall it with 2.2... if you feel like that will help.

>You are
>making assumptions that seem unwise - eg that the code didn't happen to
>work in 2.2.5 even though it was not correctly setting hardware flow
>control, or that the defaults set by the user space apps run with the
>distribution haven't changed and thus shown up such a problem.
>  
>

Understood.  Please let me know the systematic approach that you would 
like me to follow in debugging this.

>Also was the 2.2 and 2.6 on the same exact mainboard ?
>  
>

Yes.  I have several hard drives with various installations on them.  I 
just plug whichever drive in that I want to use for the OS version 
installed.  So I've got a drive with RedHat 6.0 (kernel 2.2.5) and a 
separate drive with Fedora Core 2 (2.6.5).  The installation that I did 
for the manufacturer on a separate machine is Fedora Core 6 (2.6.18).

>You've verified that flow control does not seem to be getting asserted
>for h/w control on the wires
>  
>

The manufacturer has verified this with their scope.  I can ony do this 
by watching the RTS LED on the modem... which may or may not be a 
reliable way to monitor things.

>Next question on the software side therefore is does the serial port have
>CRTSCTS set when the problem is showing up. (stty -a </dev/ttyWhatever)
>

Yes.  Here's what it looks like:

# stty -F /dev/ttyS1 -a
speed 115200 baud; rows 0; columns 0; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; 
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = 
^W; lnext = ^V; flush = ^O;
min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread clocal crtscts
-ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl 
-ixon -ixoff -iuclc -ixany -imaxbel
-opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 
bs0 vt0 ff0
-isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop 
-echoprt -echoctl -echoke
#

Thanks,

Lee.

Re: serial flow control appears broken

[Tilman Schmidt]

[-- Attachment #1: Type: text/plain, Size: 1067 bytes --]

Lee Howard schrieb:
> 
> So, does this explain why I wouldn't have a problem at 115200 bps with 
> kernel 2.2.5 but why I do with 2.6.5 and 2.6.18?  Both hardware and 
> software flow control work fine with 2.2.5 (meaning I don't see any 
> error message and I don't have any data corruption), but neither works 
> to avoid the "kernel: ttyS1: 1 input overrun(s)" and consequent data 
> corruption issue in 2.6.5 nor 2.6.18.
> 
> Was there some associated application change in tty handling that needed 
> to occur between the 2.2 and 2.6 kernels to properly implement flow control?

Could this be related?

http://lkml.org/lkml/2007/7/18/245

Quote:
"I've recently found (using 2.6.21.4) that configuring a serial ports
(ST16654) which use the 8250 driver using setserial results in the
UART's FIFOs being disabled (unless you specify autoconfig)."

-- 
Tilman Schmidt                    E-Mail: tilman@imap.cc
Bonn, Germany
Diese Nachricht besteht zu 100% aus wiederverwerteten Bits.
Ungeöffnet mindestens haltbar bis: (siehe Rückseite)


[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 250 bytes --]

Re: serial flow control appears broken

[Paul Fulghum]

Tilman Schmidt wrote:
> Could this be related?
> 
> http://lkml.org/lkml/2007/7/18/245
> 
> Quote:
> "I've recently found (using 2.6.21.4) that configuring a serial ports
> (ST16654) which use the 8250 driver using setserial results in the
> UART's FIFOs being disabled (unless you specify autoconfig)."

That would make sense.

Lee's error is a hardware FIFO overrun which could occur
if the FIFO is being disabled as described in your
link (by trying to set the uart type with setserial).

Since the tty flow control is only triggered
by the line discipline in response to ldisc
buffer levels and not hardware FIFO overruns,
you would never see any flow control action
as reported by Lee.


-- 
Paul Fulghum
Microgate Systems, Ltd.

Re: serial flow control appears broken

[Lee Howard]

Paul Fulghum wrote:

> Tilman Schmidt wrote:
>
>> Could this be related?
>>
>> http://lkml.org/lkml/2007/7/18/245
>>
>> Quote:
>> "I've recently found (using 2.6.21.4) that configuring a serial ports
>> (ST16654) which use the 8250 driver using setserial results in the
>> UART's FIFOs being disabled (unless you specify autoconfig)."
>
>
> That would make sense.
>
> Lee's error is a hardware FIFO overrun which could occur
> if the FIFO is being disabled as described in your
> link (by trying to set the uart type with setserial).


I'm not using setserial on this port, myself.  If something in init is 
calling on setserial then I don't know about it.

That said, tests on the serial port from within the application show 
that xmit_fifo_size is set to 16 as it should be.

I wrote up a little test app:

    struct serial_struct serial;
    ioctl(modemFd, TIOCGSERIAL, &serial);
    printf("            type: %d\n", serial.type);
    printf("            line: %d\n", serial.line);
    printf("            line: %u\n", serial.port);
    printf("             irq: %d\n", serial.irq);
    printf("           flags: %d\n", serial.flags);
    printf("  xmit_fifo_size: %d\n", serial.xmit_fifo_size);
    printf("  custom_divisor: %d\n", serial.custom_divisor);
    printf("       baud_base: %d\n", serial.baud_base);
    printf("     close_delay: %u\n", serial.close_delay);
    printf("         io_type: 0x%X\n", serial.io_type);
    printf("reserved_char[0]: 0x%X\n", serial.reserved_char[0]);
    printf("            hub6: %d\n", serial.hub6);
    printf("    closing_wait: %u\n", serial.closing_wait);
    printf("   closing_wait2: %u\n", serial.closing_wait2);
    printf(" iomem_reg_shift: %u\n", serial.iomem_reg_shift);
    printf("       port_high: %u\n", serial.port_high);
    printf("     reserved[0]: %d\n", serial.reserved[0]);

Here's the output:

            type: 4
            line: 1
            line: 760
             irq: 3
           flags: 1358954688
  xmit_fifo_size: 16
  custom_divisor: 0
       baud_base: 115200
     close_delay: 500
         io_type: 0x0
reserved_char[0]: 0x0
            hub6: 0
    closing_wait: 30000
   closing_wait2: 0
 iomem_reg_shift: 0
       port_high: 0
     reserved[0]: 0

Thanks,

Lee.

Re: serial flow control appears broken

[Paul Fulghum]

On Fri, 2007-07-27 at 13:48 -0700, Lee Howard wrote:
> Here's the output:
> 
>             type: 4
>             line: 1
>             line: 760
>              irq: 3
>            flags: 1358954688
>   xmit_fifo_size: 16
>   custom_divisor: 0
>        baud_base: 115200

OK, the FIFO should be enabled.

What is known:

* The error is a hardware FIFO overrun.
  - observed message is in n_tty due to driver setting TTY_OVERRUN

* The RTS/CTS flow control is not involved
  - this is done only by the ldisc in response to buffer levels
  - you verified crtscts is set
  - you did not observed RTS change when 'overflow error' logged
  - you did observe RTS change when application stopped reading

So this seems to be a latency issue reading the receive
FIFO in the ISR. The current rx FIFO trigger level
should be 8 bytes (UART_FCR_R_TRIG_10) which gives the
ISR 694usec to get the data at 115200bps.

IIRC, in 2.2.X kernels this defaulted to 4 bytes
(TRIG_01) which gave a little more time to service the interrupt.

How does the data rate affect the frequency of the overrun errors?
Does 57600bps make them go away?

--
Paul

Re: serial flow control appears broken

[Lee Howard]

Paul Fulghum wrote:

>So this seems to be a latency issue reading the receive
>FIFO in the ISR. The current rx FIFO trigger level
>should be 8 bytes (UART_FCR_R_TRIG_10) which gives the
>ISR 694usec to get the data at 115200bps.
>
>IIRC, in 2.2.X kernels this defaulted to 4 bytes
>(TRIG_01) which gave a little more time to service the interrupt.
>
>How does the data rate affect the frequency of the overrun errors?
>Does 57600bps make them go away?
>  
>

The overrun error message does not occur on every instance of data 
corruption.  (I just became aware of this as I've not been paying so 
much attention to the error messages as I have been to the corrupt 
data.)  The data gets far more corrupted than the error messages would 
lead me to believe.  Since the data being sent from the fax modem to the 
host is identical (same image data) every time it's easier for me to 
measure the effect of one bitrate over another by examining the number 
of missing bytes from the data.

The image has a total of 140465 bytes.  Just now I sent it 5 times each 
at 115200, 57600, 38400, and 19200 bps.

At 115200 bps the number of bytes skipped were:  63, 5, 44, 48, and 2.

At 57600 bps the number of bytes skipped were:  0, 1, 13, 9, and 12.

At 38400 bps the number of bytes skipped were 858, 0, 0, 0, and 8.

At 19200 bps the number of bytes skipped were 0, 0, 0, 0, and 0.

Curiously, the session at 38400 bps that skipped 858 bytes... coincided, 
not just in sequence but also in precice timing within the session, with 
a small but noticeable disk load that I caused by grepping through a 
hundred session logs.  (I can't reproduce it easily, though, because of 
disk caching.)

And, perhaps this is relevant... the way that I have the fax modem 
sending the data to the host is by receiving it from another fax modem 
which is sending it.  Thus, the modem on ttyS0 is sending a fax to the 
modem on ttyS1.  Due to the error correction protocol that is performed 
between the two fax endpoints I can guarantee that the data is correct 
as it leaves the DCE.  I mention this in case there is any limitation to 
how the 8250 driver performs when two modems are being run simultaneously.

Thanks,

Lee.

Re: serial flow control appears broken

[Russell King]

On Fri, Jul 27, 2007 at 09:51:25PM -0700, Lee Howard wrote:
> Curiously, the session at 38400 bps that skipped 858 bytes... coincided, 
> not just in sequence but also in precice timing within the session, with 
> a small but noticeable disk load that I caused by grepping through a 
> hundred session logs.  (I can't reproduce it easily, though, because of 
> disk caching.)

If you have other parts of the system which run with IRQs disabled for
a significant time period, then you will get serial corruption.  That's
not the serial driver's fault - that's a problem with the other device
drivers/rest of the system.

You may be table to track down where IRQs are being held off for too long
by hooking into the 8250 interrupt handler, and when an overrun error is
reported, printk a _minimal_ message reporting the instruction pointer
obtained via get_irq_regs().

Note, however, that I don't actively maintain serial anymore.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

Re: serial flow control appears broken

[Alan Cox]

> Curiously, the session at 38400 bps that skipped 858 bytes... coincided, 
> not just in sequence but also in precice timing within the session, with 
> a small but noticeable disk load that I caused by grepping through a 
> hundred session logs.  (I can't reproduce it easily, though, because of 
> disk caching.)

Can you send me a dmesg, there are some cases when high disk load can
cause high interrupt latency in both 2.2 and 2.6 depending upon what is
configured. I don't think thats related to the main problem but it is
worth knowing about hdparm -u1

> as it leaves the DCE.  I mention this in case there is any limitation to 
> how the 8250 driver performs when two modems are being run simultaneously.

It means more load but that shouldn't matter much, and the transmit side
if under load with asynchronous traffic will not lose bytes sending.

Alan

Re: serial flow control appears broken

[Lee Howard]

[-- Attachment #1: Type: text/plain, Size: 1235 bytes --]

Alan Cox wrote:

>>Curiously, the session at 38400 bps that skipped 858 bytes... coincided, 
>>not just in sequence but also in precice timing within the session, with 
>>a small but noticeable disk load that I caused by grepping through a 
>>hundred session logs.  (I can't reproduce it easily, though, because of 
>>disk caching.)
>>    
>>
>
>Can you send me a dmesg, there are some cases when high disk load can
>cause high interrupt latency in both 2.2 and 2.6 depending upon what is
>configured.
>

I've attached dmesg output.  The os version I used yesterday to run 
those tests was Debian 4.0r0 (kernel 2.6.18-4-686).  It's still running, 
and that's where I give you this dmesg output from.

> I don't think thats related to the main problem but it is
>worth knowing about hdparm -u1
>

# hdparm -u1 /dev/hda

/dev/hda:
 setting unmaskirq to 1 (on)
 unmaskirq    =  1 (on)
#

After doing this I re-ran the 5 test sends at 115200 bps.  The number of 
lost bytes were:  0, 14, 8, 0, and 3.  Compared with yesterday's 63, 5, 
44, 48, and 2 this may indicate an improvement.  Note also that in the 
4th session where no bytes were lost there was still one element of 
corrupt data as detected by the image decoder.

Thanks,

Lee.

[-- Attachment #2: dmesg.out --]
[-- Type: text/plain, Size: 7308 bytes --]

Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 17:17:36 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000e000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
224MB LOWMEM available.
On node 0 totalpages: 57344
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 53248 pages, LIFO batch:15
DMI 2.0 present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 10000000 (gap: 0e000000:f1ff0000)
Detected 400.953 MHz processor.
Built 1 zonelists.  Total pages: 57344
Kernel command line: root=/dev/hda3 ro 
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011c9000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 219828k/229376k available (1544k kernel code, 9052k reserved, 577k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 802.59 BogoMIPS (lpj=1605193)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
CPU0: Intel Pentium II (Deschutes) stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4375k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fc0f0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc118, dseg 0xf0000
PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Firmware left 0000:00:0b.0 e100 interrupts enabled, disabling
Boot video device is 0000:01:00.0
PCI: Bridge: 0000:00:01.0
  IO window: c000-cfff
  MEM window: e4000000-e5ffffff
  PREFETCH window: e7000000-e77fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1185563327.604:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Couldn't register serial port 0000:00:0a.0: -28
Couldn't register serial port 0000:00:0c.0: -28
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
e100: eth0: e100_probe: addr 0xe7a00000, irq 10, MAC addr 00:60:B0:68:53:F4
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596a (rev 06) IDE UDMA33 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM BIGFOOT TS12.7A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LTN301, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 25075008 sectors (12838 MB) w/418KiB Cache, CHS=24876/16/63, UDMA(33)
 hda: hda1 hda2 hda3
hdc: ATAPI 32X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Adding 498004k swap on /dev/hda2.  Priority:-1 extents:1 across:498004k
EXT3 FS on hda3, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present

Re: serial flow control appears broken

[Frantisek Rysanek]

On 28 Jul 2007 at 17:39, Lee Howard wrote:
> >>Curiously, the session at 38400 bps that skipped 858 bytes... coincided, 
> >>not just in sequence but also in precice timing within the session, with 
> >>a small but noticeable disk load that I caused by grepping through a 
> >>hundred session logs.  
>
> I've attached dmesg output.
>
I'd like to summarize a few points that have appeared in this long 
thread.

Someone else has mentioned interrupt latency.
I seem to recall that the RTAI people can measure that. 
http://issaris.org/rtai/list.php
They report that some P4-class Intel chipsets (i845/865 for example) 
that are using message-signaled interrupt passing across the HubLink 
(serialized PCI) from the South Bridge to the North Bridge, exhibit 
interrupt latencies on the order of milliseconds, if the HubLink is 
loaded by some heavy PCI transfers, such as intensive disk IO. 
Reportedly this is because the interrupt messages are competing for 
the "right of the way" with the DMA-driven PCI transactions that 
carry the bulk of the disk IO payload, where a single PCI transaction 
can take that long.

Now: you've quoted a Shuttle HOT-661. That's an older chipset, i440 
class. That one was still using the traditional out-of-band interrupt 
delivery mechanism, using the INTR signal + vector reading over the 
ISA bus. Yet, come to think of that, the native PCI interconnect 
between the MCH and the PIIX4 can still present a bottleneck to IRQ 
processing. The AT PIC is located in the PIIX4 (south bridge). After 
the INTR signal, in order to access the AT-PIC (to read the vector), 
the CPU has to reach out across that PCI bus. Now if the bus is busy 
with some lengthy PCI DMA transfer, what happens to the interrupt 
delivery?
I don't know for sure, but possibly the CPU gets stalled by the north 
bridge, until the PCI DMA transfer is over. The same would be true 
about any ISA read/write, such as legacy ISA-based serial UART 
access. If anyone knows for sure, please comment on this...

I mean to say that this may be unrelated to some other driver 
disabling interrupts explicitly. The latency may occur even with 
interrupts enabled, due to the PCI bottleneck.

Based on your dmesg listing, your disk drive and chipset have settled 
on using UDMA33. The maximum disk transfer size is 128 kB. Cannot say 
how this translates to PCI transactions. If this implied that a 
single PCI transaction could be 128 kB long, that would be almost a 
millisecond at 132 MBps (PCI speed) or some 4 ms at 33 MBps (disk 
drive speed). Again, can't say for sure if this implies a stall, or 
if the data dribbles in such a way that the 33 MBps data flow is 
interleaved with other transactions (IRQ related or not).
Mr. Fulghum has quoted 694us of slack (at 115200 bps and an 
8-Byte trigger level).

I've never seen this happen, but possibly I wasn't stressing my 
machines enough :-)

Frank Rysanek

Re: serial flow control appears broken

[Ray Lee]

On 7/27/07, Lee Howard <faxguy@howardsilvan.com> wrote:
> Curiously, the session at 38400 bps that skipped 858 bytes... coincided,
> not just in sequence but also in precice timing within the session, with
> a small but noticeable disk load that I caused by grepping through a
> hundred session logs.  (I can't reproduce it easily, though, because of
> disk caching.)

`echo 1 > /proc/sys/vm/drop_caches` will clear out most (all?) of what
the kernel has cached from the drive. It's there just for this kind of
repeatability of tests...

Ray

Re: serial flow control appears broken

[Lee Howard]

Ray Lee wrote:

>On 7/27/07, Lee Howard <faxguy@howardsilvan.com> wrote:
>  
>
>>Curiously, the session at 38400 bps that skipped 858 bytes... coincided,
>>not just in sequence but also in precice timing within the session, with
>>a small but noticeable disk load that I caused by grepping through a
>>hundred session logs.  (I can't reproduce it easily, though, because of
>>disk caching.)
>>    
>>
>
>`echo 1 > /proc/sys/vm/drop_caches` will clear out most (all?) of what
>the kernel has cached from the drive. It's there just for this kind of
>repeatability of tests...
>

And in repeat tests it is quite evident that IDE disk activity is, 
indeed, at least part of the problem.  As IDE disk activity increases an 
increased amount of data coming in on the serial port goes missing.

Thanks,

Lee.

Re: serial flow control appears broken

[Paul Fulghum]

Lee Howard wrote:
> And in repeat tests it is quite evident that IDE disk activity is, 
> indeed, at least part of the problem.  As IDE disk activity increases an 
> increased amount of data coming in on the serial port goes missing.

Lee, you mentioned 2.2.x kernels did not exhibit this problem.

Was this on the same hardware you are currently testing?
Which 2.2.x version were you using?
Was the 2.2.x serial driver also identifying the UART as a 16550A?
Can you get /proc/interrupts output
from both the current setup and the 2.2.x setup?

It would be interesting to compare the interrupt
assignment and UART setup between the versions.

--
Paul

Re: serial flow control appears broken

[Lee Howard]

Paul Fulghum wrote:

> Lee Howard wrote:
>
>> And in repeat tests it is quite evident that IDE disk activity is, 
>> indeed, at least part of the problem.  As IDE disk activity increases 
>> an increased amount of data coming in on the serial port goes missing.
>
>
> Lee, you mentioned 2.2.x kernels did not exhibit this problem.
>
> Was this on the same hardware you are currently testing?


Yes it was... except for the hard drive.  I have different installs of 
different operating systems on different hard drives.  I change the hard 
drive when switching between 2.2.5 and 2.6.5.

> Which 2.2.x version were you using?


The default 2.2.5 kernel that comes with RedHat 6.0.

> Was the 2.2.x serial driver also identifying the UART as a 16550A?


Yes it does.

> Can you get /proc/interrupts output
> from both the current setup and the 2.2.x setup?


Current (2.6.5):

           CPU0
  0:   14660696          XT-PIC  timer
  1:          8          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  3:    1240314          XT-PIC  serial
  4:     778901          XT-PIC  serial
  8:          1          XT-PIC  rtc
 10:     111647          XT-PIC  eth0
 14:     221202          XT-PIC  ide0
 15:         34          XT-PIC  ide1
NMI:          0
ERR:          5

(2.2.5):

           CPU0
  0:       5908          XT-PIC  timer
  1:         88          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  8:          2          XT-PIC  rtc
 10:        38          XT-PIC  Intel EtherExpress Pro 10/100 Ethernet
 13:          1          XT-PIC fpu
 14:        36637        XT-PIC  ide0
 15:         4          XT-PIC  ide1
NMI:          0

Thanks,

Lee.

Re: serial flow control appears broken

[Paul Fulghum]

2.2.5 is using the same UART setup (trigger level of 8) as
the current code. There is no obvious difference in the
interrupt setup (same devices on the same interrupts).

So I have no helpful suggestions :-(

--
Paul

Re: serial flow control appears broken

[Paul Fulghum]

Tilman Schmidt wrote:
> Could this be related?
> 
> http://lkml.org/lkml/2007/7/18/245
> 
> Quote:
> "I've recently found (using 2.6.21.4) that configuring a serial ports
> (ST16654) which use the 8250 driver using setserial results in the
> UART's FIFOs being disabled (unless you specify autoconfig)."

That would make sense.

Lee's error is a hardware FIFO overrun which could occur
if the FIFO is being disabled as described in your
link (by trying to set the uart type with setserial).

Since the tty flow control is only triggered
by the line discipline in response to ldisc
buffer levels and not hardware FIFO overruns,
you would never see any flow control action
as reported by Lee.


-- 
Paul Fulghum
Microgate Systems, Ltd.

Re: serial flow control appears broken

[Lee Howard]

Tilman Schmidt wrote:

>Lee Howard schrieb:
>  
>
>>So, does this explain why I wouldn't have a problem at 115200 bps with 
>>kernel 2.2.5 but why I do with 2.6.5 and 2.6.18?  Both hardware and 
>>software flow control work fine with 2.2.5 (meaning I don't see any 
>>error message and I don't have any data corruption), but neither works 
>>to avoid the "kernel: ttyS1: 1 input overrun(s)" and consequent data 
>>corruption issue in 2.6.5 nor 2.6.18.
>>
>>Was there some associated application change in tty handling that needed 
>>to occur between the 2.2 and 2.6 kernels to properly implement flow control?
>>    
>>
>
>Could this be related?
>
>http://lkml.org/lkml/2007/7/18/245
>
>Quote:
>"I've recently found (using 2.6.21.4) that configuring a serial ports
>(ST16654) which use the 8250 driver using setserial results in the
>UART's FIFOs being disabled (unless you specify autoconfig)."
>  
>

I'm not running setserial on the port, myself.  But to test to see if it 
is related, I included this code in the application:

#include <linux/serial.h>
....
struct serial_struct serial;
ioctl(modemFd, TIOCGSERIAL, &serial);
traceModemOp("modem xmit_fifo_size: %u", serial.xmit_fifo_size);

And I get this resulting logging:

"MODEM modem xmit_fifo_size: 16"

So it's clear from here that the xmit_fifo_size is set correctly on this 
system.

Thanks,

Lee.

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Thu, 26 Jul 2007, Lee Howard wrote:

> If the application were to use TIOCM_RTS how would it know when to apply it or
> not?  Is there some approach that the application could take to manage flow
> control on the serial port?  What about software flow control?  Does the

 Well, an application could negate RTS when it receives a character and 
is running out of resources for further processing of incoming data.

 Smarter UARTs may be able to negate RTS themselves based on the amount of 
data in their receive FIFO.  The threshold may be configurable.

  Maciej

Re: serial flow control appears broken

[Lee Howard]

Maciej W. Rozycki wrote:

>On Thu, 26 Jul 2007, Lee Howard wrote:
>
>  
>
>>If the application were to use TIOCM_RTS how would it know when to apply it or
>>not?  Is there some approach that the application could take to manage flow
>>control on the serial port?  What about software flow control?  Does the
>>    
>>
>
> Well, an application could negate RTS when it receives a character and 
>is running out of resources for further processing of incoming data.
>
> Smarter UARTs may be able to negate RTS themselves based on the amount of 
>data in their receive FIFO.  The threshold may be configurable.
>

Okay, so let's say we've got a loop around a blocking read on the modem 
file descriptor...

  for (;;) {
      read some data from modem
      process data from modem
      if (end-of-data detected) break;
  }

Are you suggesting that the application should be using deasserting RTS 
after the read and asserting it before?

I had previously thought that the control of RTS was something that the 
serial/tty driver was supposed to do independently based on the buffer 
fill.  Was I wrong?

Thanks,

Lee.

Re: serial flow control appears broken

[Alan Cox]

> I had previously thought that the control of RTS was something that the 
> serial/tty driver was supposed to do independently based on the buffer 
> fill.  Was I wrong?

If the kernel is asked to do CRTSCTS then the kernel handles the flow
control. It uses it when the internal buffers are nearly full.

The direct access to the lines is normally only used by special drivers
such as half duplex radio modem drivers.

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Fri, 27 Jul 2007, Lee Howard wrote:

> Okay, so let's say we've got a loop around a blocking read on the modem file
> descriptor...
> 
>  for (;;) {
>      read some data from modem
>      process data from modem
>      if (end-of-data detected) break;
>  }
> 
> Are you suggesting that the application should be using deasserting RTS after
> the read and asserting it before?

 It certainly could -- you were asking how it would know. ;-)

> I had previously thought that the control of RTS was something that the
> serial/tty driver was supposed to do independently based on the buffer fill.

 The TTY line discipline driver could do that based on the amount of 
received data present in its buffer.  And it should if asked to (a brief 
look at drivers/char/n_tty.c reveals it does; obviously there may be a bug 
somewhere though).  So could e.g. the SLIP and PPP line discipline 
drivers, though the criteria might be different (apparently they do not, 
which is a shame).

 The serial drivers have nothing to do about it -- all they can do is 
pushing data upstream, to the discipline driver.  They can provide an 
interface to hardware flow control features though, if implemented by a 
given UART.

  Maciej

Re: serial flow control appears broken

[Lee Howard]

Maciej W. Rozycki wrote:

> The TTY line discipline driver could do that based on the amount of 
>received data present in its buffer.  And it should if asked to (a brief 
>look at drivers/char/n_tty.c reveals it does; obviously there may be a bug 
>somewhere though).  So could e.g. the SLIP and PPP line discipline 
>drivers, though the criteria might be different (apparently they do not, 
>which is a shame).
>
> The serial drivers have nothing to do about it -- all they can do is 
>pushing data upstream, to the discipline driver.  They can provide an 
>interface to hardware flow control features though, if implemented by a 
>given UART.
>

Thank you for this clarification.  So I should have more correctly been 
saying that "tty flow control appears broken".  Right?

I've asked the manufacturer to take a look at drivers/char/n_tty.c to 
see if they can't see anything obvious.

Thanks,

Lee.

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Fri, 27 Jul 2007, Lee Howard wrote:

> >The serial drivers have nothing to do about it -- all they can do is pushing
> >data upstream, to the discipline driver.  They can provide an interface to
> >hardware flow control features though, if implemented by a given UART.
> >
> 
> Thank you for this clarification.  So I should have more correctly been saying
> that "tty flow control appears broken".  Right?

 Probably.  It might be, as Alan suggested, that it is meant to work, but 
the latency kills it.

  Maciej

Re: serial flow control appears broken

[Robert Hancock]

Maciej W. Rozycki wrote:
> On Fri, 27 Jul 2007, Lee Howard wrote:
> 
>> Okay, so let's say we've got a loop around a blocking read on the modem file
>> descriptor...
>>
>>  for (;;) {
>>      read some data from modem
>>      process data from modem
>>      if (end-of-data detected) break;
>>  }
>>
>> Are you suggesting that the application should be using deasserting RTS after
>> the read and asserting it before?
> 
>  It certainly could -- you were asking how it would know. ;-)
> 
>> I had previously thought that the control of RTS was something that the
>> serial/tty driver was supposed to do independently based on the buffer fill.
> 
>  The TTY line discipline driver could do that based on the amount of 
> received data present in its buffer.  And it should if asked to (a brief 
> look at drivers/char/n_tty.c reveals it does; obviously there may be a bug 

Really, where? In my look through the code I haven't found any mechanism 
that would result in RTS being lowered based on TTY buffers filling up, 
at least not in the 8250 case.

In this situation, though, it appears it's not the TTY buffers that are 
filling but the UART's own buffer. I would think this must be caused by 
some kind of interrupt latency that results in not draining the FIFO in 
time.

> somewhere though).  So could e.g. the SLIP and PPP line discipline 
> drivers, though the criteria might be different (apparently they do not, 
> which is a shame).
> 
>  The serial drivers have nothing to do about it -- all they can do is 
> pushing data upstream, to the discipline driver.  They can provide an 
> interface to hardware flow control features though, if implemented by a 
> given UART.
> 
>   Maciej
> 

Re: serial flow control appears broken

[Paul Fulghum]

On Fri, 2007-07-27 at 12:22 -0600, Robert Hancock wrote:
> Maciej W. Rozycki wrote:
> >  The TTY line discipline driver could do that based on the amount of 
> > received data present in its buffer.  And it should if asked to (a brief 
> > look at drivers/char/n_tty.c reveals it does; obviously there may be a bug 
> 
> Really, where? In my look through the code I haven't found any mechanism 
> that would result in RTS being lowered based on TTY buffers filling up, 
> at least not in the 8250 case.

serial_core.c:uart_throttle()
serial_core.c:uart_unthrottle()

These are called by N_TTY in response to buffer levels.
 
--
Paul Fulghum
Microgate Systems, Ltd

Re: serial flow control appears broken

[Paul Fulghum]

On Fri, 2007-07-27 at 12:22 -0600, Robert Hancock wrote:

> In this situation, though, it appears it's not the TTY buffers that are 
> filling but the UART's own buffer. I would think this must be caused by 
> some kind of interrupt latency that results in not draining the FIFO in 
> time.

You are right, this error is output when the character flag TTY_OVERRUN
is encountered by n_tty.c which should be set by the driver
in response to a hardware FIFO overrun (not an ldisc buffer overrun).

I can't see anyplace in serial_core.c or 8250.c that sets TTY_OVERRUN.

 
--
Paul Fulghum
Microgate Systems, Ltd

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Fri, 27 Jul 2007, Paul Fulghum wrote:

> I can't see anyplace in serial_core.c or 8250.c that sets TTY_OVERRUN.

 Look for UART_LSR_OE in 8250.c -- the serial core accepts any bit that 
has been defined by the low-level driver and sets TTY_OVERRUN in 
uart_insert_char().

  Maciej

Re: serial flow control appears broken

[Paul Fulghum]

OK, I see where TTY_OVERRUN is set:
include/linux/serial_core.h:uart_insert_char()


--
Paul Fulghum
Microgate Systems, Ltd

Re: serial flow control appears broken

[Russell King]

On Fri, Jul 27, 2007 at 12:22:57PM -0600, Robert Hancock wrote:
> Maciej W. Rozycki wrote:
> > The TTY line discipline driver could do that based on the amount of 
> >received data present in its buffer.  And it should if asked to (a brief 
> >look at drivers/char/n_tty.c reveals it does; obviously there may be a bug 
> 
> Really, where? In my look through the code I haven't found any mechanism 
> that would result in RTS being lowered based on TTY buffers filling up, 
> at least not in the 8250 case.

That's something for the line discipline to decide.

> In this situation, though, it appears it's not the TTY buffers that are 
> filling but the UART's own buffer. I would think this must be caused by 
> some kind of interrupt latency that results in not draining the FIFO in 
> time.

Correct, and suggested approach to tracking down the culpret has been
mentioned in a previous email.

Also note that there's nothing the serial driver can do to detect this
condition before it occurs.  The problem occurs because the serial driver
is starved of CPU time due to other parts of the system, and the driver
has precisely zero knowledge as to when that's going to happen.

There are two possible scenarios when such starvation can occur:

1. interrupts are disabled for a long period.
2. the serial interrupt has started to run, but has been interrupted
   by _another_ interrupt which runs for a long period.

Essentially, any complex interrupt handler (such as an IDE interrupt
doing a multi-sector PIO transfer _in interrupt context_) can cause this
kind of starvation.  That's why Linux 1.x had bottom halves - so that
the time consuming work could be moved out of the interrupt handler,
thereby causing minimal the blockage of other interrupts.

Unfortunately, that kind of design has been long since forgotten.
Apparantly modern machines are fast enough that it doesn't have to be
worried about anymore...  Or are they?

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Sat, 28 Jul 2007, Russell King wrote:

> Essentially, any complex interrupt handler (such as an IDE interrupt
> doing a multi-sector PIO transfer _in interrupt context_) can cause this
> kind of starvation.  That's why Linux 1.x had bottom halves - so that
> the time consuming work could be moved out of the interrupt handler,
> thereby causing minimal the blockage of other interrupts.
> 
> Unfortunately, that kind of design has been long since forgotten.
> Apparantly modern machines are fast enough that it doesn't have to be
> worried about anymore...  Or are they?

 I would guess it is not that the machines are fast enough, but that this 
two-level processing makes things more complicated.  Enough that most 
people would not bother digging into it unless really forced.  Only 
occasional latency problems are probably not enough of a force.

  Maciej

Re: serial flow control appears broken

[Russell King]

On Mon, Jul 30, 2007 at 10:45:19AM +0100, Maciej W. Rozycki wrote:
> On Sat, 28 Jul 2007, Russell King wrote:
> 
> > Essentially, any complex interrupt handler (such as an IDE interrupt
> > doing a multi-sector PIO transfer _in interrupt context_) can cause this
> > kind of starvation.  That's why Linux 1.x had bottom halves - so that
> > the time consuming work could be moved out of the interrupt handler,
> > thereby causing minimal the blockage of other interrupts.
> > 
> > Unfortunately, that kind of design has been long since forgotten.
> > Apparantly modern machines are fast enough that it doesn't have to be
> > worried about anymore...  Or are they?
> 
>  I would guess it is not that the machines are fast enough, but that this 
> two-level processing makes things more complicated.  Enough that most 
> people would not bother digging into it unless really forced.  Only 
> occasional latency problems are probably not enough of a force.

It's a shame we don't have a way to measure IRQ latency - it would be
very useful to flag up problems.

I think the best we could do is to arrange for the timer interrupt to
complain if it's delayed by more than 1ms or so - but some architectures
already run their timers with IRQF_DISABLED as a work around some of
the latency issues.

-- 
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:

Re: serial flow control appears broken

[Mark Lord]

Maciej W. Rozycki wrote:
> On Sat, 28 Jul 2007, Russell King wrote:
> 
>> Essentially, any complex interrupt handler (such as an IDE interrupt
>> doing a multi-sector PIO transfer _in interrupt context_) can cause this
>> kind of starvation.  That's why Linux 1.x had bottom halves - so that
>> the time consuming work could be moved out of the interrupt handler,
>> thereby causing minimal the blockage of other interrupts.
>>
>> Unfortunately, that kind of design has been long since forgotten.
>> Apparantly modern machines are fast enough that it doesn't have to be
>> worried about anymore...  Or are they?
> 
>  I would guess it is not that the machines are fast enough, but that this 
> two-level processing makes things more complicated.  Enough that most 
> people would not bother digging into it unless really forced.  Only 
> occasional latency problems are probably not enough of a force.

I don't believe the speed of the machine has much to do with it,
as IDE PIO is always at pretty much the same speed (or slower)
regardless of the CPU speed.

Best case is about .120 usec per 16-bit word, but that doesn't often pan out
in practice.  More typical is something closer to 1 usec per 16-bit word.

So, for multcount=16 (very common), best case is 16 * 256 * .120 = 491 usec,
plus extra overhead for reading the IDE status register (another usec or so),
and other stuff.  Figure maybe 500usec total per interrupt for multcount=16
in the best case, or 4000usec in the worst case.

At 115200bps, we get a byte every 86 usec or so.  Assuming the UART FIFO
is set to interrupt (warn) us at 12/16 full, we have 4*86 = 344 usec to
respond and de-assert RTS.  Less than that in practice.

Conclusion:  using IDE multisector PIO is not a good idea with high speed
serial transfers happening, since we cannot respond quickly enough.

It might be possible to set the buffer underrun threshold lower in the UART (?).

All that said, I doubt that his system is using IDE PIO in the first place.
Dunno how long IDE DMA interrupts take, but it's probably in the 20-50 usec range.

Re: serial flow control appears broken

[Robert Hancock]

Mark Lord wrote:
> I don't believe the speed of the machine has much to do with it,
> as IDE PIO is always at pretty much the same speed (or slower)
> regardless of the CPU speed.
> 
> Best case is about .120 usec per 16-bit word, but that doesn't often pan 
> out
> in practice.  More typical is something closer to 1 usec per 16-bit word.
> 
> So, for multcount=16 (very common), best case is 16 * 256 * .120 = 491 
> usec,
> plus extra overhead for reading the IDE status register (another usec or 
> so),
> and other stuff.  Figure maybe 500usec total per interrupt for multcount=16
> in the best case, or 4000usec in the worst case.
> 
> At 115200bps, we get a byte every 86 usec or so.  Assuming the UART FIFO
> is set to interrupt (warn) us at 12/16 full, we have 4*86 = 344 usec to
> respond and de-assert RTS.  Less than that in practice.
> 
> Conclusion:  using IDE multisector PIO is not a good idea with high speed
> serial transfers happening, since we cannot respond quickly enough.
> 
> It might be possible to set the buffer underrun threshold lower in the 
> UART (?).
> 
> All that said, I doubt that his system is using IDE PIO in the first place.
> Dunno how long IDE DMA interrupts take, but it's probably in the 20-50 
> usec range.

I think that PIO transfers only have to be done with interrupts disabled 
on really old, evil controllers (without unmask set). I don't think 
libata ever disables interrupts during transfers(?)

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/

Re: serial flow control appears broken

[Mark Lord]

Robert Hancock wrote:
> Mark Lord wrote:
>> I don't believe the speed of the machine has much to do with it,
>> as IDE PIO is always at pretty much the same speed (or slower)
>> regardless of the CPU speed.
>>
>> Best case is about .120 usec per 16-bit word, but that doesn't often 
>> pan out
>> in practice.  More typical is something closer to 1 usec per 16-bit word.
>>
>> So, for multcount=16 (very common), best case is 16 * 256 * .120 = 491 
>> usec,
>> plus extra overhead for reading the IDE status register (another usec 
>> or so),
>> and other stuff.  Figure maybe 500usec total per interrupt for 
>> multcount=16
>> in the best case, or 4000usec in the worst case.
>>
>> At 115200bps, we get a byte every 86 usec or so.  Assuming the UART FIFO
>> is set to interrupt (warn) us at 12/16 full, we have 4*86 = 344 usec to
>> respond and de-assert RTS.  Less than that in practice.
>>
>> Conclusion:  using IDE multisector PIO is not a good idea with high speed
>> serial transfers happening, since we cannot respond quickly enough.
>>
>> It might be possible to set the buffer underrun threshold lower in the 
>> UART (?).
>>
>> All that said, I doubt that his system is using IDE PIO in the first 
>> place.
>> Dunno how long IDE DMA interrupts take, but it's probably in the 20-50 
>> usec range.
> 
> I think that PIO transfers only have to be done with interrupts disabled 
> on really old, evil controllers (without unmask set). I don't think 
> libata ever disables interrupts during transfers(?)

That's what "hdparm -u1" (or -u0) controls.

But it doesn't matter a whit here.  The problem is that the IDE interrupt
handling can take a long time, regardless of whether it unmasks IRQs or not.
And if that IDE interrupt interrupts a serial interrupt, then the serial
stuff won't get handled until the IDE stuff completes.  Thus the problem.

The "fix" could be to have the serial IRQ handler never unmask interrupts,
but that's a bit unsociable to others.  The IDE stuff really needs to not
do so much during the actual IRQ handler.

Ingo's RT patches would probably fix all of this.
 

Re: serial flow control appears broken

[Robert Hancock]

Mark Lord wrote:
>> I think that PIO transfers only have to be done with interrupts 
>> disabled on really old, evil controllers (without unmask set). I don't 
>> think libata ever disables interrupts during transfers(?)
> 
> That's what "hdparm -u1" (or -u0) controls.
> 
> But it doesn't matter a whit here.  The problem is that the IDE interrupt
> handling can take a long time, regardless of whether it unmasks IRQs or 
> not.
> And if that IDE interrupt interrupts a serial interrupt, then the serial
> stuff won't get handled until the IDE stuff completes.  Thus the problem.
> 
> The "fix" could be to have the serial IRQ handler never unmask interrupts,
> but that's a bit unsociable to others.  The IDE stuff really needs to not
> do so much during the actual IRQ handler.
> 
> Ingo's RT patches would probably fix all of this.

libata also doesn't do the actual PIO transfer from the interrupt 
handler like old IDE does, either, and it only disables interrupts for 
the transfer if it's transferring to/from high memory..

-- 
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from hancockr@nospamshaw.ca
Home Page: http://www.roberthancock.com/

Re: serial flow control appears broken

[Alan Cox]

> That's what "hdparm -u1" (or -u0) controls.

Only some of the time.

> Ingo's RT patches would probably fix all of this.

The worst case IDE times we've seen for executing a single indivisible
un-interruptible I/O cycle with a drive are around 1mS. Thats a hardware
limit.

Alan

Re: serial flow control appears broken

[Lee Howard]

Mark Lord wrote:

> The "fix" could be to have the serial IRQ handler never unmask 
> interrupts,
> but that's a bit unsociable to others.  The IDE stuff really needs to not
> do so much during the actual IRQ handler.
>
> Ingo's RT patches would probably fix all of this.


I did a Fedora 7 installation and installed Ingo's kernel from here:

http://people.redhat.com/mingo/realtime-preempt/yum-testing/yum/i686/kernel-rt-2.6.21-0182.rt11cfsv17.i686.rpm

Even then, the problem still occurs, unfortunately.

Thanks,

Lee.

Re: serial flow control appears broken

[Alan Cox]

> I think that PIO transfers only have to be done with interrupts disabled 
> on really old, evil controllers (without unmask set). I don't think 
> libata ever disables interrupts during transfers(?)

Currently libata PIO is mostly done in the IRQ path. Albert Lee was doing
some work on that but its actually very hard to fix without doing polled
PIO.

Re: serial flow control appears broken

[Robert Hancock]

Alan Cox wrote:
>> I think that PIO transfers only have to be done with interrupts disabled 
>> on really old, evil controllers (without unmask set). I don't think 
>> libata ever disables interrupts during transfers(?)
> 
> Currently libata PIO is mostly done in the IRQ path. Albert Lee was doing
> some work on that but its actually very hard to fix without doing polled
> PIO.

Ah, right. Misread the code.

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Thu, 2 Aug 2007, Alan Cox wrote:

> Currently libata PIO is mostly done in the IRQ path. Albert Lee was doing
> some work on that but its actually very hard to fix without doing polled
> PIO.

 Hmm, when the drive signals it is ready for a PIO data transfer can't 
just the interrupt handler mask the originating interrupt and post a 
softirq to handle the case?  That should be rather straightforward.

  Maciej

Re: serial flow control appears broken

[Maciej W. Rozycki]

On Fri, 27 Jul 2007, Robert Hancock wrote:

> > The TTY line discipline driver could do that based on the amount of received
> > data present in its buffer.  And it should if asked to (a brief look at
> > drivers/char/n_tty.c reveals it does; obviously there may be a bug 
> 
> Really, where? In my look through the code I haven't found any mechanism that
> would result in RTS being lowered based on TTY buffers filling up, at least
> not in the 8250 case.

 Look for calls to ->throttle() and ->unthrottle().  XON and XOFF might be 
used instead as a result of these calls though, depending on terminal 
settings.

> In this situation, though, it appears it's not the TTY buffers that are
> filling but the UART's own buffer. I would think this must be caused by some
> kind of interrupt latency that results in not draining the FIFO in time.

 Well, the UART only has its FIFO which is rather small, so automatic flow 
control would be useful.  Though, admittedly, tty_insert_flip_char() might 
return some kind of a status related to how much space is left in the 
receive buffer which would indicate that there is a lag in data stream 
processing -- which in turn may relate to the system being loaded, so that 
the receive ISR could decide whether to negate RTS itself for the less 
capable UARTs (i.e. ones with no autoflow and a tiny or no FIFO).

  Maciej

Re: serial flow control appears broken

[Lee Howard]

Maciej W. Rozycki wrote:

>On Fri, 27 Jul 2007, Lee Howard wrote:
>
>  
>
>>Okay, so let's say we've got a loop around a blocking read on the modem file
>>descriptor...
>>
>> for (;;) {
>>     read some data from modem
>>     process data from modem
>>     if (end-of-data detected) break;
>> }
>>
>>Are you suggesting that the application should be using deasserting RTS after
>>the read and asserting it before?
>>    
>>
>
> It certainly could -- you were asking how it would know. ;-)
>

So, to test... I put this in the application before every read:

    int flags;
    ioctl(modemFd, TIOCMGET, &flags);
    flags |= TIOCM_RTS;
    ioctl(modemFd, TIOCMSET, &flags);

and this after:

    int flags;
    ioctl(modemFd, TIOCMGET, &flags);
    flags &= ~TIOCM_RTS;
    ioctl(modemFd, TIOCMSET, &flags);

Now I can see the RTS light blink on the modem (and during heavy 
communication it merely "dims" depending on the amount of delay in the 
processing.

However, it does not help.  Data still goes missing.

Thanks,

Lee.

serial flow control appears broken

[Lee Howard]

Hello.

I have fax modems that will, in their proper behavior with certain 
features, send up to 64 kilobytes of data to the host DTE all at once.  
(So, the fax modem handles an incoming fax and periodically will send 
between 256 bytes and 64 kilobytes of data in bursts.)

When the DCE-DTE (modem-to-host) communication rate is established at 
115200 bps data loss occurs systems using at least Linux kernels 2.6.5 
and 2.6.18 (and probably everything in-beween and then some more).  This 
is because the modem overflows the host's buffer.  This is evidenced in 
kernel logging:

Jul 23 14:01:30 gollum kernel: ttyS1: 1 input overrun(s)
Jul 23 17:09:45 gollum kernel: ttyS1: 1 input overrun(s)

Normally I would blame the modem itself for not honoring the host's flow 
control signals.  However, I have worked with the modem manufacturer 
closely on this matter for over three months now.  In that process they 
have improved the responsiveness of the modem and have fixed other 
problems, but the end result is that it truly does appear that the 
serial tty driver is not using flow control.  Whether software flow 
control (XON/XOFF) or hardware flow control (RTS/CTS) is used the result 
is the same.

This is evidenced in hardware flow control by a little LED labeled "RTS" 
that is on the external modem.  This LED lights up when pin 7 of the DB9 
serial connection is given +12Vdc current (signalling "RTS" is on - that 
the host can accept data).  The LED goes dark when the current is 
removed (signalling that the host cannot accept data).  This "RTS" LED 
never flickers at all, as it should, when receiving these bursts of data 
- the LED stays lit as long as the serial cable is connected to the 
host... and yet I will see those "input overrun" messages.  Thus, it 
seems quite clear that the Linux serial tty driver is not deasserting 
RTS as it should in hardware flow control.  (And probably the analogous 
problem exists in software flow control, too.)

Please tell me what I can do to help you resove and/or remedy this 
matter.  Also, please let me know if I have contacted the wrong people.  
(I have cross-posted to linux-kernel as a catch-all.  I am not 
subscribed to either linux-serial or linux-kernel mailing lists.  So 
please CC me in any list responses.)

If it is of any value to know (perhaps they have common code?), the same 
error occurs on FreeBSD 6.2 as well.   The problem does not occur on 
Windows.  The problem does not occur on RedHat 6.0 (kernel 2.2.5).

Thanks,

Lee.

Re: serial flow control appears broken

[Uwe Kleine-König]

Hello,

> This is evidenced in hardware flow control by a little LED labeled "RTS" 
> that is on the external modem.  This LED lights up when pin 7 of the DB9 
> serial connection is given +12Vdc current (signalling "RTS" is on - that 
> the host can accept data).  The LED goes dark when the current is 
> removed (signalling that the host cannot accept data).  This "RTS" LED 
> never flickers at all, as it should, when receiving these bursts of data 
> - the LED stays lit as long as the serial cable is connected to the 
> host... and yet I will see those "input overrun" messages.  Thus, it 
> seems quite clear that the Linux serial tty driver is not deasserting 
> RTS as it should in hardware flow control.  (And probably the analogous 
> problem exists in software flow control, too.)
I don't know the relevant timings for problem, but just to be sure that
your prerequisites are correct:  How did you check that the LED stays
lit all the time?  Just from looking might not be accurate.  You might
want to mesure the signal with an oscilloscope.

Just my 0.02¢
Uwe

-- 
Uwe Kleine-König

fib where fib = 0 : 1 : zipWith (+) fib (tail fib)
-
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: serial flow control appears broken

[Lee Howard]

Uwe Kleine-König wrote:

>Hello,
>
>  
>
>>This is evidenced in hardware flow control by a little LED labeled "RTS" 
>>that is on the external modem.  This LED lights up when pin 7 of the DB9 
>>serial connection is given +12Vdc current (signalling "RTS" is on - that 
>>the host can accept data).  The LED goes dark when the current is 
>>removed (signalling that the host cannot accept data).  This "RTS" LED 
>>never flickers at all, as it should, when receiving these bursts of data 
>>- the LED stays lit as long as the serial cable is connected to the 
>>host... and yet I will see those "input overrun" messages.  Thus, it 
>>seems quite clear that the Linux serial tty driver is not deasserting 
>>RTS as it should in hardware flow control.  (And probably the analogous 
>>problem exists in software flow control, too.)
>>    
>>
>I don't know the relevant timings for problem, but just to be sure that
>your prerequisites are correct:  How did you check that the LED stays
>lit all the time?  Just from looking might not be accurate.  You might
>want to mesure the signal with an oscilloscope.
>

The manufacturer is using a scope to look for RTS and they're not seeing 
it, either.  I just use my eyes to look at the LED, but I can see the 
CTS, DTR, DCD, RD, and TD lights blink, flicker, or dim... (and TD, RD, 
and CTS tend to go on and off rather quickly).

All of that said... even though I don't see RTS flicker or blink or dim 
when using kernel 2.2.5 (RedHat 6.0) I don't have any problems using 
115200 bps DTE-DCE communication rate.

Thanks,

Lee.
-
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: serial flow control appears broken

[Alan Cox]

> The manufacturer is using a scope to look for RTS and they're not seeing 
> it, either.  I just use my eyes to look at the LED, but I can see the 
> CTS, DTR, DCD, RD, and TD lights blink, flicker, or dim... (and TD, RD, 
> and CTS tend to go on and off rather quickly).

And you have

1.	The port set up correctly for flow control options in the
kernel ?
2.	Verified that the board vendor remembered to wire it ?

Re: serial flow control appears broken

[Lee Howard]

Alan Cox wrote:

>>The manufacturer is using a scope to look for RTS and they're not seeing 
>>it, either.  I just use my eyes to look at the LED, but I can see the 
>>CTS, DTR, DCD, RD, and TD lights blink, flicker, or dim... (and TD, RD, 
>>and CTS tend to go on and off rather quickly).
>>    
>>
>
>And you have
>
>1.	The port set up correctly for flow control options in the
>kernel ?
>  
>

I suppose that you mean that the application has properly set up the 
port using termios/tcsetattr/ioctl and the like... rather than if the 
kernel build/config options were set to permit flow control (I know of 
no relevant flow-control-enabling kernel build options).  Using hardware 
flow control this is what stty tells me about the port set up done by 
the application:

# stty -F /dev/ttyS1 -a
speed 115200 baud; rows 0; columns 0; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; 
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = 
^W; lnext = ^V; flush = ^O;
min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread clocal crtscts
-ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl 
-ixon -ixoff -iuclc -ixany -imaxbel
-opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 
bs0 vt0 ff0
-isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop 
-echoprt -echoctl -echoke
#

Using software flow control this is what stty tells me about the port 
set up done by the application:

# stty -F /dev/ttyS1 -a
speed 115200 baud; rows 0; columns 0; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; 
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = 
^W; lnext = ^V; flush = ^O;
min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread clocal -crtscts
-ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl ixon 
ixoff -iuclc -ixany -imaxbel
-opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 
bs0 vt0 ff0
-isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop 
-echoprt -echoctl -echoke
#

They seem correct to me, but I am certainly willing to be wrong.

>2.	Verified that the board vendor remembered to wire it ?
>

I don't know how to verify directly that the board manufacturer wired 
the serial port correctly.  I've tested this on two different 
motherboards made several years apart (but, yes, both were made by the 
same manufacturer).  However, when using RedHat 6.0 (kernel 2.2.5) I 
have no problems with data corruption occurring in the data coming from 
the DCE.  So that tells me that *something* was working before that 
isn't working now... and I'm trying to determine what the difference 
is... whether it be a problem in modern kernels or whether it be 
something that the application (HylaFAX) is not doing to accomodate 
whatever changes occurred in modern kernels.

A quick google on "input overrun(s)" may lend some credence (although, 
certainly this is not in any way conclusive) that I'm not the only one 
who may be seeking a solution on this matter.

  http://www.google.com/search?hl=en&q=%2B%22input+overrun%28s%29%22

Thanks,

Lee.

Re: serial flow control appears broken

[Alan Cox]

> -parenb -parodd cs8 -hupcl -cstopb cread clocal crtscts

Ok so crtscts is set, but you have clocal set too. That shouldn't matter

> Using software flow control this is what stty tells me about the port 
> set up done by the application:

This also looks fine

> They seem correct to me, but I am certainly willing to be wrong.

clocal set as well is unusual but if I remember the spec right then
clocal would not interfere with rts/cts handshake and certainly not with
xon/xoff

Looks correct, two boards so its unlikely both didnt wire it.

> A quick google on "input overrun(s)" may lend some credence (although, 
> certainly this is not in any way conclusive) that I'm not the only one 
> who may be seeking a solution on this matter.
> 
>   http://www.google.com/search?hl=en&q=%2B%22input+overrun%28s%29%22

Those look different on the whole - there are two reasons you'll get an
input overrun with a 16x50 UART. The first is because we ran out of
buffers to empty the chip, in which case we would have asserted flow
control in software. The second is if we cannot keep up and fail to empty
the on chip FIFO within the required time (about 1mS)

As the flow control is driven by software on most 16x50 chips (there are
a couple of exceptions) if we fail to empty the fifo fast enough then any
flow control will be asserted too late to save the day.

If you stop the application and do the following

	cat /dev/ttywhatever
	^Z
	[stopped]

(so you are asking the OS to buffer data but not ever reading it)

and then fire data at it does the flow control eventually occur ?

Alan

Re: serial flow control appears broken

[Lee Howard]

Alan Cox wrote:

>As the flow control is driven by software on most 16x50 chips (there are
>a couple of exceptions) if we fail to empty the fifo fast enough then any
>flow control will be asserted too late to save the day.
>
>If you stop the application and do the following
>
>	cat /dev/ttywhatever
>	^Z
>	[stopped]
>
>(so you are asking the OS to buffer data but not ever reading it)
>
>and then fire data at it does the flow control eventually occur ?
>

Yes it does appear to.  I told the application to simply sleep(300) at 
the appropriate moment, and I watched the application and when it began 
the sleep I ran:

  cat /dev/ttyS1
  (lots of "garbage" began spewing forth)
  ^Z
  (about 2 or 3 seconds and the RTS light goes dark)

Thanks,

Lee.

RE: serial flow control appears broken

[Tosoni]

Trivial check:

Did you set the CRTSCTS flag in the c_cflag parameter to tcsetattr() in your
linux application code ? Or in the corresponding ioctl(..., TCSETA,...) call
?


> -----Original Message-----
> From: linux-serial-owner@vger.kernel.org
> [mailto:linux-serial-owner@vger.kernel.org]On Behalf Of Lee Howard
> Sent: Thursday, July 26, 2007 3:53 AM
> To: linux-serial@vger.kernel.org; tytso@mit.edu; rmk@arm.linux.org.uk;
> linux-kernel@vger.kernel.org
> Subject: serial flow control appears broken
>
>
> Hello.
>
> I have fax modems that will, in their proper behavior with certain
> features, send up to 64 kilobytes of data to the host DTE all
> at once.
> (So, the fax modem handles an incoming fax and periodically will send
> between 256 bytes and 64 kilobytes of data in bursts.)
>
> When the DCE-DTE (modem-to-host) communication rate is established at
> 115200 bps data loss occurs systems using at least Linux
> kernels 2.6.5
> and 2.6.18 (and probably everything in-beween and then some
> more).  This
> is because the modem overflows the host's buffer.  This is
> evidenced in
> kernel logging:
>
> Jul 23 14:01:30 gollum kernel: ttyS1: 1 input overrun(s)
> Jul 23 17:09:45 gollum kernel: ttyS1: 1 input overrun(s)
>
> Normally I would blame the modem itself for not honoring the
> host's flow
> control signals.  However, I have worked with the modem manufacturer
> closely on this matter for over three months now.  In that
> process they
> have improved the responsiveness of the modem and have fixed other
> problems, but the end result is that it truly does appear that the
> serial tty driver is not using flow control.  Whether software flow
> control (XON/XOFF) or hardware flow control (RTS/CTS) is used
> the result
> is the same.
>
> This is evidenced in hardware flow control by a little LED
> labeled "RTS"
> that is on the external modem.  This LED lights up when pin 7
> of the DB9
> serial connection is given +12Vdc current (signalling "RTS"
> is on - that
> the host can accept data).  The LED goes dark when the current is
> removed (signalling that the host cannot accept data).  This
> "RTS" LED
> never flickers at all, as it should, when receiving these
> bursts of data
> - the LED stays lit as long as the serial cable is connected to the
> host... and yet I will see those "input overrun" messages.  Thus, it
> seems quite clear that the Linux serial tty driver is not deasserting
> RTS as it should in hardware flow control.  (And probably the
> analogous
> problem exists in software flow control, too.)
>
> Please tell me what I can do to help you resove and/or remedy this
> matter.  Also, please let me know if I have contacted the
> wrong people.
> (I have cross-posted to linux-kernel as a catch-all.  I am not
> subscribed to either linux-serial or linux-kernel mailing lists.  So
> please CC me in any list responses.)
>
> If it is of any value to know (perhaps they have common
> code?), the same
> error occurs on FreeBSD 6.2 as well.   The problem does not occur on
> Windows.  The problem does not occur on RedHat 6.0 (kernel 2.2.5).
>
> Thanks,
>
> Lee.
>
> -
> To unsubscribe from this list: send the line "unsubscribe
> linux-serial" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>

Re: serial flow control appears broken

[Lee Howard]

Yes, CRTSCTS is set.  Here is what stty says...

# stty -F /dev/ttyS1 -a
speed 115200 baud; rows 0; columns 0; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; 
eol2 = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = 
^W; lnext = ^V; flush = ^O;
min = 1; time = 0;
-parenb -parodd cs8 -hupcl -cstopb cread clocal crtscts
-ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr -icrnl 
-ixon -ixoff -iuclc -ixany -imaxbel
-opost -olcuc -ocrnl -onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 
bs0 vt0 ff0
-isig -icanon -iexten -echo -echoe -echok -echonl -noflsh -xcase -tostop 
-echoprt -echoctl -echoke
#

Thanks,

Lee.


Tosoni wrote:

>Trivial check:
>
>Did you set the CRTSCTS flag in the c_cflag parameter to tcsetattr() in your
>linux application code ? Or in the corresponding ioctl(..., TCSETA,...) call
>?
>
>
>  
>
>>-----Original Message-----
>>From: linux-serial-owner@vger.kernel.org
>>[mailto:linux-serial-owner@vger.kernel.org]On Behalf Of Lee Howard
>>Sent: Thursday, July 26, 2007 3:53 AM
>>To: linux-serial@vger.kernel.org; tytso@mit.edu; rmk@arm.linux.org.uk;
>>linux-kernel@vger.kernel.org
>>Subject: serial flow control appears broken
>>
>>
>>Hello.
>>
>>I have fax modems that will, in their proper behavior with certain
>>features, send up to 64 kilobytes of data to the host DTE all
>>at once.
>>(So, the fax modem handles an incoming fax and periodically will send
>>between 256 bytes and 64 kilobytes of data in bursts.)
>>
>>When the DCE-DTE (modem-to-host) communication rate is established at
>>115200 bps data loss occurs systems using at least Linux
>>kernels 2.6.5
>>and 2.6.18 (and probably everything in-beween and then some
>>more).  This
>>is because the modem overflows the host's buffer.  This is
>>evidenced in
>>kernel logging:
>>
>>Jul 23 14:01:30 gollum kernel: ttyS1: 1 input overrun(s)
>>Jul 23 17:09:45 gollum kernel: ttyS1: 1 input overrun(s)
>>
>>Normally I would blame the modem itself for not honoring the
>>host's flow
>>control signals.  However, I have worked with the modem manufacturer
>>closely on this matter for over three months now.  In that
>>process they
>>have improved the responsiveness of the modem and have fixed other
>>problems, but the end result is that it truly does appear that the
>>serial tty driver is not using flow control.  Whether software flow
>>control (XON/XOFF) or hardware flow control (RTS/CTS) is used
>>the result
>>is the same.
>>
>>This is evidenced in hardware flow control by a little LED
>>labeled "RTS"
>>that is on the external modem.  This LED lights up when pin 7
>>of the DB9
>>serial connection is given +12Vdc current (signalling "RTS"
>>is on - that
>>the host can accept data).  The LED goes dark when the current is
>>removed (signalling that the host cannot accept data).  This
>>"RTS" LED
>>never flickers at all, as it should, when receiving these
>>bursts of data
>>- the LED stays lit as long as the serial cable is connected to the
>>host... and yet I will see those "input overrun" messages.  Thus, it
>>seems quite clear that the Linux serial tty driver is not deasserting
>>RTS as it should in hardware flow control.  (And probably the
>>analogous
>>problem exists in software flow control, too.)
>>
>>Please tell me what I can do to help you resove and/or remedy this
>>matter.  Also, please let me know if I have contacted the
>>wrong people.
>>(I have cross-posted to linux-kernel as a catch-all.  I am not
>>subscribed to either linux-serial or linux-kernel mailing lists.  So
>>please CC me in any list responses.)
>>
>>If it is of any value to know (perhaps they have common
>>code?), the same
>>error occurs on FreeBSD 6.2 as well.   The problem does not occur on
>>Windows.  The problem does not occur on RedHat 6.0 (kernel 2.2.5).
>>
>>Thanks,
>>
>>Lee.
>>
>>-
>>To unsubscribe from this list: send the line "unsubscribe
>>linux-serial" in
>>the body of a message to majordomo@vger.kernel.org
>>More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>
>>    
>>
>
>
>  
>