* [PATCH V5 04/10] MIPS: lantiq: add serial port support
[not found] <1301470076-17279-1-git-send-email-blogic@openwrt.org>
@ 2011-03-30 7:27 ` John Crispin
2011-03-30 9:33 ` Alan Cox
0 siblings, 1 reply; 2+ messages in thread
From: John Crispin @ 2011-03-30 7:27 UTC (permalink / raw)
To: Ralf Baechle
Cc: John Crispin, Ralph Hempel, Felix Fietkau, linux-mips,
linux-serial
This patch adds the driver for the 2 serial ports found inside the Lantiq SoC family
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-serial@vger.kernel.org
---
Changes in V2
* small cleanups
* use global register access macros
* properly register memory resources
Changes in V3
* whitespace
* change __iomem void to void __iomem
* multiline comments
* use pr_* macros instead of printk
Changes in V4
* remove unused defines
* clean code that requests the interrupts
* add linux-serial to the CC list
drivers/tty/serial/Kconfig | 8 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/lantiq.c | 733 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 742 insertions(+), 0 deletions(-)
create mode 100644 drivers/tty/serial/lantiq.c
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index e1aee37..bfb346b 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1391,6 +1391,14 @@ config SERIAL_OF_PLATFORM_NWPSERIAL_CONSOLE
help
Support for Console on the NWP serial ports.
+config SERIAL_LANTIQ
+ bool "Lantiq serial driver"
+ depends on LANTIQ
+ select SERIAL_CORE
+ select SERIAL_CORE_CONSOLE
+ help
+ Support for console and UART on Lantiq SoCs.
+
config SERIAL_QE
tristate "Freescale QUICC Engine serial port support"
depends on QUICC_ENGINE
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index fee0690..3527604 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -94,3 +94,4 @@ obj-$(CONFIG_SERIAL_IFX6X60) += ifx6x60.o
obj-$(CONFIG_SERIAL_PCH_UART) += pch_uart.o
obj-$(CONFIG_SERIAL_MSM_SMD) += msm_smd_tty.o
obj-$(CONFIG_SERIAL_MXS_AUART) += mxs-auart.o
+obj-$(CONFIG_SERIAL_LANTIQ) += lantiq.o
diff --git a/drivers/tty/serial/lantiq.c b/drivers/tty/serial/lantiq.c
new file mode 100644
index 0000000..9923d3d
--- /dev/null
+++ b/drivers/tty/serial/lantiq.c
@@ -0,0 +1,733 @@
+/*
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * Copyright (C) 2004 Infineon IFAP DC COM CPE
+ * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2007 John Crispin <blogic@openwrt.org>
+ * Copyright (C) 2010 Thomas Langer, <thomas.langer@lantiq.com>
+ */
+
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+
+#include <lantiq_soc.h>
+
+#define PORT_LTQ_ASC 111
+#define MAXPORTS 2
+#define UART_DUMMY_UER_RX 1
+#define DRVNAME "ltq_asc"
+#ifdef __BIG_ENDIAN
+#define LTQ_ASC_TBUF (0x0020 + 3)
+#define LTQ_ASC_RBUF (0x0024 + 3)
+#else
+#define LTQ_ASC_TBUF 0x0020
+#define LTQ_ASC_RBUF 0x0024
+#endif
+#define LTQ_ASC_FSTAT 0x0048
+#define LTQ_ASC_WHBSTATE 0x0018
+#define LTQ_ASC_STATE 0x0014
+#define LTQ_ASC_IRNCR 0x00F8
+#define LTQ_ASC_CLC 0x0000
+#define LTQ_ASC_ID 0x0008
+#define LTQ_ASC_PISEL 0x0004
+#define LTQ_ASC_TXFCON 0x0044
+#define LTQ_ASC_RXFCON 0x0040
+#define LTQ_ASC_CON 0x0010
+#define LTQ_ASC_BG 0x0050
+#define LTQ_ASC_IRNREN 0x00F4
+
+#define ASC_IRNREN_TX 0x1
+#define ASC_IRNREN_RX 0x2
+#define ASC_IRNREN_ERR 0x4
+#define ASC_IRNREN_TX_BUF 0x8
+#define ASC_IRNCR_TIR 0x1
+#define ASC_IRNCR_RIR 0x2
+#define ASC_IRNCR_EIR 0x4
+
+#define ASCOPT_CSIZE 0x3
+#define TXFIFO_FL 1
+#define RXFIFO_FL 1
+#define ASCCLC_DISS 0x2
+#define ASCCLC_RMCMASK 0x0000FF00
+#define ASCCLC_RMCOFFSET 8
+#define ASCCON_M_8ASYNC 0x0
+#define ASCCON_M_7ASYNC 0x2
+#define ASCCON_ODD 0x00000020
+#define ASCCON_STP 0x00000080
+#define ASCCON_BRS 0x00000100
+#define ASCCON_FDE 0x00000200
+#define ASCCON_R 0x00008000
+#define ASCCON_FEN 0x00020000
+#define ASCCON_ROEN 0x00080000
+#define ASCCON_TOEN 0x00100000
+#define ASCSTATE_PE 0x00010000
+#define ASCSTATE_FE 0x00020000
+#define ASCSTATE_ROE 0x00080000
+#define ASCSTATE_ANY (ASCSTATE_ROE|ASCSTATE_PE|ASCSTATE_FE)
+#define ASCWHBSTATE_CLRREN 0x00000001
+#define ASCWHBSTATE_SETREN 0x00000002
+#define ASCWHBSTATE_CLRPE 0x00000004
+#define ASCWHBSTATE_CLRFE 0x00000008
+#define ASCWHBSTATE_CLRROE 0x00000020
+#define ASCTXFCON_TXFEN 0x0001
+#define ASCTXFCON_TXFFLU 0x0002
+#define ASCTXFCON_TXFITLMASK 0x3F00
+#define ASCTXFCON_TXFITLOFF 8
+#define ASCRXFCON_RXFEN 0x0001
+#define ASCRXFCON_RXFFLU 0x0002
+#define ASCRXFCON_RXFITLMASK 0x3F00
+#define ASCRXFCON_RXFITLOFF 8
+#define ASCFSTAT_RXFFLMASK 0x003F
+#define ASCFSTAT_TXFFLMASK 0x3F00
+#define ASCFSTAT_TXFREEMASK 0x3F000000
+#define ASCFSTAT_TXFREEOFF 24
+
+static void lqasc_tx_chars(struct uart_port *port);
+static struct ltq_uart_port *lqasc_port[MAXPORTS];
+static struct uart_driver lqasc_reg;
+
+struct ltq_uart_port {
+ struct uart_port port;
+ struct clk *clk;
+ unsigned int tx_irq;
+ unsigned int rx_irq;
+ unsigned int err_irq;
+};
+
+static inline struct
+ltq_uart_port *to_ltq_uart_port(struct uart_port *port)
+{
+ return container_of(port, struct ltq_uart_port, port);
+}
+
+static void
+lqasc_stop_tx(struct uart_port *port)
+{
+ return;
+}
+
+static void
+lqasc_start_tx(struct uart_port *port)
+{
+ unsigned long flags;
+ local_irq_save(flags);
+ lqasc_tx_chars(port);
+ local_irq_restore(flags);
+ return;
+}
+
+static void
+lqasc_stop_rx(struct uart_port *port)
+{
+ ltq_w32(ASCWHBSTATE_CLRREN, port->membase + LTQ_ASC_WHBSTATE);
+}
+
+static void
+lqasc_enable_ms(struct uart_port *port)
+{
+}
+
+static void
+lqasc_rx_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = port->state->port.tty;
+ unsigned int ch = 0, rsr = 0, fifocnt;
+
+ fifocnt =
+ ltq_r32(port->membase + LTQ_ASC_FSTAT) & ASCFSTAT_RXFFLMASK;
+ while (fifocnt--) {
+ u8 flag = TTY_NORMAL;
+ ch = ltq_r8(port->membase + LTQ_ASC_RBUF);
+ rsr = (ltq_r32(port->membase + LTQ_ASC_STATE)
+ & ASCSTATE_ANY) | UART_DUMMY_UER_RX;
+ tty_flip_buffer_push(tty);
+ port->icount.rx++;
+
+ /*
+ * Note that the error handling code is
+ * out of the main execution path
+ */
+ if (rsr & ASCSTATE_ANY) {
+ if (rsr & ASCSTATE_PE) {
+ port->icount.parity++;
+ ltq_w32_mask(0, ASCWHBSTATE_CLRPE,
+ port->membase + LTQ_ASC_WHBSTATE);
+ } else if (rsr & ASCSTATE_FE) {
+ port->icount.frame++;
+ ltq_w32_mask(0, ASCWHBSTATE_CLRFE,
+ port->membase + LTQ_ASC_WHBSTATE);
+ }
+ if (rsr & ASCSTATE_ROE) {
+ port->icount.overrun++;
+ ltq_w32_mask(0, ASCWHBSTATE_CLRROE,
+ port->membase + LTQ_ASC_WHBSTATE);
+ }
+
+ rsr &= port->read_status_mask;
+
+ if (rsr & ASCSTATE_PE)
+ flag = TTY_PARITY;
+ else if (rsr & ASCSTATE_FE)
+ flag = TTY_FRAME;
+ }
+
+ if ((rsr & port->ignore_status_mask) == 0)
+ tty_insert_flip_char(tty, ch, flag);
+
+ if (rsr & ASCSTATE_ROE)
+ /*
+ * Overrun is special, since it's reported
+ * immediately, and doesn't affect the current
+ * character
+ */
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ }
+ if (ch != 0)
+ tty_flip_buffer_push(tty);
+ return;
+}
+
+static void
+lqasc_tx_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+ if (uart_tx_stopped(port)) {
+ lqasc_stop_tx(port);
+ return;
+ }
+
+ while (((ltq_r32(port->membase + LTQ_ASC_FSTAT) &
+ ASCFSTAT_TXFREEMASK) >> ASCFSTAT_TXFREEOFF) != 0) {
+ if (port->x_char) {
+ ltq_w8(port->x_char, port->membase + LTQ_ASC_TBUF);
+ port->icount.tx++;
+ port->x_char = 0;
+ continue;
+ }
+
+ if (uart_circ_empty(xmit))
+ break;
+
+ ltq_w8(port->state->xmit.buf[port->state->xmit.tail],
+ port->membase + LTQ_ASC_TBUF);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+}
+
+static irqreturn_t
+lqasc_tx_int(int irq, void *_port)
+{
+ struct uart_port *port = (struct uart_port *)_port;
+ ltq_w32(ASC_IRNCR_TIR, port->membase + LTQ_ASC_IRNCR);
+ lqasc_start_tx(port);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t
+lqasc_err_int(int irq, void *_port)
+{
+ struct uart_port *port = (struct uart_port *)_port;
+ /* clear any pending interrupts */
+ ltq_w32_mask(0, ASCWHBSTATE_CLRPE | ASCWHBSTATE_CLRFE |
+ ASCWHBSTATE_CLRROE, port->membase + LTQ_ASC_WHBSTATE);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t
+lqasc_rx_int(int irq, void *_port)
+{
+ struct uart_port *port = (struct uart_port *)_port;
+ ltq_w32(ASC_IRNCR_RIR, port->membase + LTQ_ASC_IRNCR);
+ lqasc_rx_chars(port);
+ return IRQ_HANDLED;
+}
+
+static unsigned int
+lqasc_tx_empty(struct uart_port *port)
+{
+ int status;
+ status = ltq_r32(port->membase + LTQ_ASC_FSTAT) & ASCFSTAT_TXFFLMASK;
+ return status ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int
+lqasc_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_CAR | TIOCM_DSR;
+}
+
+static void
+lqasc_set_mctrl(struct uart_port *port, u_int mctrl)
+{
+}
+
+static void
+lqasc_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+static int
+lqasc_startup(struct uart_port *port)
+{
+ struct ltq_uart_port *ltq_port = to_ltq_uart_port(port);
+ int retval;
+
+ port->uartclk = clk_get_rate(ltq_port->clk);
+
+ ltq_w32_mask(ASCCLC_DISS | ASCCLC_RMCMASK, (1 << ASCCLC_RMCOFFSET),
+ port->membase + LTQ_ASC_CLC);
+
+ ltq_w32(0, port->membase + LTQ_ASC_PISEL);
+ ltq_w32(
+ ((TXFIFO_FL << ASCTXFCON_TXFITLOFF) & ASCTXFCON_TXFITLMASK) |
+ ASCTXFCON_TXFEN | ASCTXFCON_TXFFLU,
+ port->membase + LTQ_ASC_TXFCON);
+ ltq_w32(
+ ((RXFIFO_FL << ASCRXFCON_RXFITLOFF) & ASCRXFCON_RXFITLMASK)
+ | ASCRXFCON_RXFEN | ASCRXFCON_RXFFLU,
+ port->membase + LTQ_ASC_RXFCON);
+ /* make sure other settings are written to hardware before
+ * setting enable bits
+ */
+ wmb();
+ ltq_w32_mask(0, ASCCON_M_8ASYNC | ASCCON_FEN | ASCCON_TOEN |
+ ASCCON_ROEN, port->membase + LTQ_ASC_CON);
+
+ retval = request_irq(ltq_port->tx_irq, lqasc_tx_int,
+ IRQF_DISABLED, "asc_tx", port);
+ if (retval) {
+ pr_err("failed to request lqasc_tx_int\n");
+ return retval;
+ }
+
+ retval = request_irq(ltq_port->rx_irq, lqasc_rx_int,
+ IRQF_DISABLED, "asc_rx", port);
+ if (retval) {
+ pr_err("failed to request lqasc_rx_int\n");
+ goto err1;
+ }
+
+ retval = request_irq(ltq_port->err_irq, lqasc_err_int,
+ IRQF_DISABLED, "asc_err", port);
+ if (retval) {
+ pr_err("failed to request lqasc_err_int\n");
+ goto err2;
+ }
+
+ ltq_w32(ASC_IRNREN_RX | ASC_IRNREN_ERR | ASC_IRNREN_TX,
+ port->membase + LTQ_ASC_IRNREN);
+ return 0;
+
+err2:
+ free_irq(ltq_port->rx_irq, port);
+err1:
+ free_irq(ltq_port->tx_irq, port);
+ return retval;
+}
+
+static void
+lqasc_shutdown(struct uart_port *port)
+{
+ struct ltq_uart_port *ltq_port = to_ltq_uart_port(port);
+ free_irq(ltq_port->tx_irq, port);
+ free_irq(ltq_port->rx_irq, port);
+ free_irq(ltq_port->err_irq, port);
+
+ ltq_w32(0, port->membase + LTQ_ASC_CON);
+ ltq_w32_mask(ASCRXFCON_RXFEN, ASCRXFCON_RXFFLU,
+ port->membase + LTQ_ASC_RXFCON);
+ ltq_w32_mask(ASCTXFCON_TXFEN, ASCTXFCON_TXFFLU,
+ port->membase + LTQ_ASC_TXFCON);
+}
+
+static void
+lqasc_set_termios(struct uart_port *port,
+ struct ktermios *new, struct ktermios *old)
+{
+ unsigned int cflag;
+ unsigned int iflag;
+ unsigned int divisor;
+ unsigned int baud;
+ unsigned int con = 0;
+ unsigned long flags;
+
+ cflag = new->c_cflag;
+ iflag = new->c_iflag;
+
+ switch (cflag & CSIZE) {
+ case CS7:
+ con = ASCCON_M_7ASYNC;
+ break;
+
+ case CS5:
+ case CS6:
+ default:
+ con = ASCCON_M_8ASYNC;
+ break;
+ }
+
+ if (cflag & CSTOPB)
+ con |= ASCCON_STP;
+
+ if (cflag & PARENB) {
+ if (!(cflag & PARODD))
+ con &= ~ASCCON_ODD;
+ else
+ con |= ASCCON_ODD;
+ }
+
+ port->read_status_mask = ASCSTATE_ROE;
+ if (iflag & INPCK)
+ port->read_status_mask |= ASCSTATE_FE | ASCSTATE_PE;
+
+ port->ignore_status_mask = 0;
+ if (iflag & IGNPAR)
+ port->ignore_status_mask |= ASCSTATE_FE | ASCSTATE_PE;
+
+ if (iflag & IGNBRK) {
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (iflag & IGNPAR)
+ port->ignore_status_mask |= ASCSTATE_ROE;
+ }
+
+ if ((cflag & CREAD) == 0)
+ port->ignore_status_mask |= UART_DUMMY_UER_RX;
+
+ /* set error signals - framing, parity and overrun, enable receiver */
+ con |= ASCCON_FEN | ASCCON_TOEN | ASCCON_ROEN;
+
+ local_irq_save(flags);
+
+ /* set up CON */
+ ltq_w32_mask(0, con, port->membase + LTQ_ASC_CON);
+
+ /* Set baud rate - take a divider of 2 into account */
+ baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
+ divisor = uart_get_divisor(port, baud);
+ divisor = divisor / 2 - 1;
+
+ /* disable the baudrate generator */
+ ltq_w32_mask(ASCCON_R, 0, port->membase + LTQ_ASC_CON);
+
+ /* make sure the fractional divider is off */
+ ltq_w32_mask(ASCCON_FDE, 0, port->membase + LTQ_ASC_CON);
+
+ /* set up to use divisor of 2 */
+ ltq_w32_mask(ASCCON_BRS, 0, port->membase + LTQ_ASC_CON);
+
+ /* now we can write the new baudrate into the register */
+ ltq_w32(divisor, port->membase + LTQ_ASC_BG);
+
+ /* turn the baudrate generator back on */
+ ltq_w32_mask(0, ASCCON_R, port->membase + LTQ_ASC_CON);
+
+ /* enable rx */
+ ltq_w32(ASCWHBSTATE_SETREN, port->membase + LTQ_ASC_WHBSTATE);
+
+ local_irq_restore(flags);
+}
+
+static const char*
+lqasc_type(struct uart_port *port)
+{
+ if (port->type == PORT_LTQ_ASC)
+ return DRVNAME;
+ else
+ return NULL;
+}
+
+static void
+lqasc_release_port(struct uart_port *port)
+{
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
+}
+
+static int
+lqasc_request_port(struct uart_port *port)
+{
+ struct platform_device *pdev = to_platform_device(port->dev);
+ struct resource *res;
+ int size;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "cannot obtain I/O memory region");
+ return -ENODEV;
+ }
+ size = resource_size(res);
+
+ res = devm_request_mem_region(&pdev->dev, res->start,
+ size, dev_name(&pdev->dev));
+ if (!res) {
+ dev_err(&pdev->dev, "cannot request I/O memory region");
+ return -EBUSY;
+ }
+
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = devm_ioremap_nocache(&pdev->dev,
+ port->mapbase, size);
+ if (port->membase == NULL)
+ return -ENOMEM;
+ }
+ return 0;
+}
+
+static void
+lqasc_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_LTQ_ASC;
+ lqasc_request_port(port);
+ }
+}
+
+static int
+lqasc_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ int ret = 0;
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_LTQ_ASC)
+ ret = -EINVAL;
+ if (ser->irq < 0 || ser->irq >= NR_IRQS)
+ ret = -EINVAL;
+ if (ser->baud_base < 9600)
+ ret = -EINVAL;
+ return ret;
+}
+
+static struct uart_ops lqasc_pops = {
+ .tx_empty = lqasc_tx_empty,
+ .set_mctrl = lqasc_set_mctrl,
+ .get_mctrl = lqasc_get_mctrl,
+ .stop_tx = lqasc_stop_tx,
+ .start_tx = lqasc_start_tx,
+ .stop_rx = lqasc_stop_rx,
+ .enable_ms = lqasc_enable_ms,
+ .break_ctl = lqasc_break_ctl,
+ .startup = lqasc_startup,
+ .shutdown = lqasc_shutdown,
+ .set_termios = lqasc_set_termios,
+ .type = lqasc_type,
+ .release_port = lqasc_release_port,
+ .request_port = lqasc_request_port,
+ .config_port = lqasc_config_port,
+ .verify_port = lqasc_verify_port,
+};
+
+static void
+lqasc_console_putchar(struct uart_port *port, int ch)
+{
+ int fifofree;
+
+ if (!port->membase)
+ return;
+
+ do {
+ fifofree = (ltq_r32(port->membase + LTQ_ASC_FSTAT)
+ & ASCFSTAT_TXFREEMASK) >> ASCFSTAT_TXFREEOFF;
+ } while (fifofree == 0);
+ ltq_w8(ch, port->membase + LTQ_ASC_TBUF);
+}
+
+
+static void
+lqasc_console_write(struct console *co, const char *s, u_int count)
+{
+ struct ltq_uart_port *ltq_port;
+ struct uart_port *port;
+ unsigned long flags;
+
+ if (co->index >= MAXPORTS)
+ return;
+
+ ltq_port = lqasc_port[co->index];
+ if (!ltq_port)
+ return;
+
+ port = <q_port->port;
+
+ local_irq_save(flags);
+ uart_console_write(port, s, count, lqasc_console_putchar);
+ local_irq_restore(flags);
+}
+
+static int __init
+lqasc_console_setup(struct console *co, char *options)
+{
+ struct ltq_uart_port *ltq_port;
+ struct uart_port *port;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index >= MAXPORTS)
+ return -ENODEV;
+
+ ltq_port = lqasc_port[co->index];
+ if (!ltq_port)
+ return -ENODEV;
+
+ port = <q_port->port;
+
+ port->uartclk = clk_get_rate(ltq_port->clk);
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct console lqasc_console = {
+ .name = "ttyS",
+ .write = lqasc_console_write,
+ .device = uart_console_device,
+ .setup = lqasc_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &lqasc_reg,
+};
+
+static int __init
+lqasc_console_init(void)
+{
+ register_console(&lqasc_console);
+ return 0;
+}
+console_initcall(lqasc_console_init);
+
+static struct uart_driver lqasc_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = DRVNAME,
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = MAXPORTS,
+ .cons = &lqasc_console,
+};
+
+static int __init
+lqasc_probe(struct platform_device *pdev)
+{
+ struct ltq_uart_port *ltq_port;
+ struct uart_port *port;
+ struct resource *mmres, *irqres;
+ int tx_irq, rx_irq, err_irq;
+ struct clk *clk;
+ int ret;
+
+ mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irqres = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!mmres || !irqres)
+ return -ENODEV;
+
+ if (pdev->id >= MAXPORTS)
+ return -EBUSY;
+
+ if (lqasc_port[pdev->id] != NULL)
+ return -EBUSY;
+
+ clk = clk_get(&pdev->dev, "fpi");
+ if (IS_ERR(clk)) {
+ pr_err("failed to get fpi clk\n");
+ return -ENOENT;
+ }
+
+ tx_irq = platform_get_irq_byname(pdev, "tx");
+ rx_irq = platform_get_irq_byname(pdev, "rx");
+ err_irq = platform_get_irq_byname(pdev, "err");
+ if ((tx_irq < 0) | (rx_irq < 0) | (err_irq < 0))
+ return -ENODEV;
+
+ ltq_port = kzalloc(sizeof(struct ltq_uart_port), GFP_KERNEL);
+ if (!ltq_port)
+ return -ENOMEM;
+
+ port = <q_port->port;
+
+ port->iotype = SERIAL_IO_MEM;
+ port->flags = ASYNC_BOOT_AUTOCONF | UPF_IOREMAP;
+ port->ops = &lqasc_pops;
+ port->fifosize = 16;
+ port->type = PORT_LTQ_ASC,
+ port->line = pdev->id;
+ port->dev = &pdev->dev;
+
+ port->irq = tx_irq; /* unused, just to be backward-compatibe */
+ port->mapbase = mmres->start;
+
+ ltq_port->clk = clk;
+
+ ltq_port->tx_irq = tx_irq;
+ ltq_port->rx_irq = rx_irq;
+ ltq_port->err_irq = err_irq;
+
+ lqasc_port[pdev->id] = ltq_port;
+ platform_set_drvdata(pdev, ltq_port);
+
+ ret = uart_add_one_port(&lqasc_reg, port);
+
+ return ret;
+}
+
+static struct platform_driver lqasc_driver = {
+ .driver = {
+ .name = DRVNAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+int __init
+init_lqasc(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&lqasc_reg);
+ if (ret != 0)
+ return ret;
+
+ ret = platform_driver_probe(&lqasc_driver, lqasc_probe);
+ if (ret != 0)
+ uart_unregister_driver(&lqasc_reg);
+
+ return ret;
+}
+
+module_init(init_lqasc);
+
+MODULE_DESCRIPTION("Lantiq serial port driver");
+MODULE_LICENSE("GPL");
--
1.7.2.3
^ permalink raw reply related [flat|nested] 2+ messages in thread