[PATCH 1/2] serial:blackfin: Put TX IRQ in individual platform resource.

[PATCH 1/2] serial:blackfin: Put TX IRQ in individual platform resource.

[Sonic Zhang]

From: Sonic Zhang <sonic.zhang@analog.com>

Serial TX IRQ is not RX IRQ plus 1 in some blackfin chips.
Give individual platform resources to both TX and RX irqs.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
---
 drivers/tty/serial/bfin_uart.c |   35 +++++++++++++++++++++--------------
 1 files changed, 21 insertions(+), 14 deletions(-)

diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index e08bc04..b907a2a 100644
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -667,17 +667,17 @@ static int bfin_serial_startup(struct uart_port *port)
 		kgdboc_break_enabled = 0;
 	else {
 # endif
-	if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
+	if (request_irq(uart->rx_irq, bfin_serial_rx_int, IRQF_DISABLED,
 	     "BFIN_UART_RX", uart)) {
 		printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
 		return -EBUSY;
 	}
 
 	if (request_irq
-	    (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
+	    (uart->port.tx_irq, bfin_serial_tx_int, IRQF_DISABLED,
 	     "BFIN_UART_TX", uart)) {
 		printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
-		free_irq(uart->port.irq, uart);
+		free_irq(uart->rx_irq, uart);
 		return -EBUSY;
 	}
 
@@ -692,7 +692,7 @@ static int bfin_serial_startup(struct uart_port *port)
 		 */
 		unsigned uart_dma_ch_rx, uart_dma_ch_tx;
 
-		switch (uart->port.irq) {
+		switch (uart->rx_irq) {
 		case IRQ_UART3_RX:
 			uart_dma_ch_rx = CH_UART3_RX;
 			uart_dma_ch_tx = CH_UART3_TX;
@@ -709,16 +709,16 @@ static int bfin_serial_startup(struct uart_port *port)
 		if (uart_dma_ch_rx &&
 			request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
 			printk(KERN_NOTICE"Fail to attach UART interrupt\n");
-			free_irq(uart->port.irq, uart);
-			free_irq(uart->port.irq + 1, uart);
+			free_irq(uart->rx_irq, uart);
+			free_irq(uart->tx_irq, uart);
 			return -EBUSY;
 		}
 		if (uart_dma_ch_tx &&
 			request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
 			printk(KERN_NOTICE "Fail to attach UART interrupt\n");
 			free_dma(uart_dma_ch_rx);
-			free_irq(uart->port.irq, uart);
-			free_irq(uart->port.irq + 1, uart);
+			free_irq(uart->rx_irq, uart);
+			free_irq(uart->tx_irq, uart);
 			return -EBUSY;
 		}
 	}
@@ -785,8 +785,8 @@ static void bfin_serial_shutdown(struct uart_port *port)
 		break;
 	};
 #endif
-	free_irq(uart->port.irq, uart);
-	free_irq(uart->port.irq+1, uart);
+	free_irq(uart->rx_irq, uart);
+	free_irq(uart->tx_irq, uart);
 #endif
 
 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
@@ -1319,14 +1319,21 @@ static int bfin_serial_probe(struct platform_device *pdev)
 		}
 		uart->port.mapbase = res->start;
 
-		uart->port.irq = platform_get_irq(pdev, 0);
-		if (uart->port.irq < 0) {
-			dev_err(&pdev->dev, "No uart RX/TX IRQ specified\n");
+		uart->tx_irq = platform_get_irq(pdev, 0);
+		if (uart->tx_irq < 0) {
+			dev_err(&pdev->dev, "No uart TX IRQ specified\n");
 			ret = -ENOENT;
 			goto out_error_unmap;
 		}
 
-		uart->status_irq = platform_get_irq(pdev, 1);
+		uart->rx_irq = platform_get_irq(pdev, 1);
+		if (uart->rx_irq < 0) {
+			dev_err(&pdev->dev, "No uart RX IRQ specified\n");
+			ret = -ENOENT;
+			goto out_error_unmap;
+		}
+
+		uart->status_irq = platform_get_irq(pdev, 2);
 		if (uart->status_irq < 0) {
 			dev_err(&pdev->dev, "No uart status IRQ specified\n");
 			ret = -ENOENT;
-- 
1.7.0.4