From mboxrd@z Thu Jan 1 00:00:00 1970 From: Greg Kroah-Hartman Subject: [PATCH 51/79] cris: lower the printk level in cris serial driver Date: Wed, 26 Oct 2011 14:12:56 +0200 Message-ID: <1319631204-23262-51-git-send-email-gregkh@suse.de> References: <20111026114236.GA22180@kroah.com> <1319631204-23262-1-git-send-email-gregkh@suse.de> Return-path: Received: from cantor2.suse.de ([195.135.220.15]:32813 "EHLO mx2.suse.de" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932922Ab1JZMNx (ORCPT ); Wed, 26 Oct 2011 08:13:53 -0400 In-Reply-To: <1319631204-23262-1-git-send-email-gregkh@suse.de> Sender: linux-serial-owner@vger.kernel.org List-Id: linux-serial@vger.kernel.org To: linux-serial@vger.kernel.org Cc: WANG Cong , Geert Uytterhoeven , Mikael Starvik , Jesper Nilsson , Greg Kroah-Hartman From: WANG Cong KERN_CRIT is too high, replace those KERN_CRIT with KERN_ERR or KERN_WARNING. Cc: Geert Uytterhoeven Cc: Mikael Starvik Cc: Jesper Nilsson Signed-off-by: WANG Cong Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/crisv10.c | 12 ++++++------ 1 files changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c index 58be715..a931524 100644 --- a/drivers/tty/serial/crisv10.c +++ b/drivers/tty/serial/crisv10.c @@ -1788,7 +1788,7 @@ static unsigned int handle_descr_data(struct e100_serial *info, struct etrax_recv_buffer *buffer = phys_to_virt(descr->buf) - sizeof *buffer; if (info->recv_cnt + recvl > 65536) { - printk(KERN_CRIT + printk(KERN_WARNING "%s: Too much pending incoming serial data! Dropping %u bytes.\n", __func__, recvl); return 0; } @@ -3813,13 +3813,13 @@ rs_close(struct tty_struct *tty, struct file * filp) * one, we've got real problems, since it means the * serial port won't be shutdown. */ - printk(KERN_CRIT + printk(KERN_ERR "rs_close: bad serial port count; tty->count is 1, " "info->count is %d\n", info->count); info->count = 1; } if (--info->count < 0) { - printk(KERN_CRIT "rs_close: bad serial port count for ttyS%d: %d\n", + printk(KERN_ERR "rs_close: bad serial port count for ttyS%d: %d\n", info->line, info->count); info->count = 0; } @@ -4452,7 +4452,7 @@ static int __init rs_init(void) #if defined(CONFIG_ETRAX_RS485_ON_PA) if (cris_io_interface_allocate_pins(if_serial_0, 'a', rs485_pa_bit, rs485_pa_bit)) { - printk(KERN_CRIT "ETRAX100LX serial: Could not allocate " + printk(KERN_ERR "ETRAX100LX serial: Could not allocate " "RS485 pin\n"); put_tty_driver(driver); return -EBUSY; @@ -4461,7 +4461,7 @@ static int __init rs_init(void) #if defined(CONFIG_ETRAX_RS485_ON_PORT_G) if (cris_io_interface_allocate_pins(if_serial_0, 'g', rs485_pa_bit, rs485_port_g_bit)) { - printk(KERN_CRIT "ETRAX100LX serial: Could not allocate " + printk(KERN_ERR "ETRAX100LX serial: Could not allocate " "RS485 pin\n"); put_tty_driver(driver); return -EBUSY; @@ -4494,7 +4494,7 @@ static int __init rs_init(void) if (info->enabled) { if (cris_request_io_interface(info->io_if, info->io_if_description)) { - printk(KERN_CRIT "ETRAX100LX async serial: " + printk(KERN_ERR "ETRAX100LX async serial: " "Could not allocate IO pins for " "%s, port %d\n", info->io_if_description, i); -- 1.7.7