* [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags
[not found] <1333356489-5816-1-git-send-email-govindraj.raja@ti.com>
@ 2012-04-03 13:42 ` Govindraj.R
2012-04-04 14:10 ` Jon Hunter
2012-04-05 11:12 ` Shubhrajyoti
0 siblings, 2 replies; 3+ messages in thread
From: Govindraj.R @ 2012-04-03 13:42 UTC (permalink / raw)
To: linux-omap
Cc: linux-serial, linux-arm-kernel, Govindraj.R, Jon Hunter,
Paul Walmsley, Kevin Hilman, Felipe Balbi
From: "Govindraj.R" <govindraj.raja@ti.com>
Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
---
arch/arm/mach-omap2/serial.c | 8 ---
arch/arm/plat-omap/include/plat/omap-serial.h | 1 -
drivers/tty/serial/omap-serial.c | 74 ++++++++++++++++++++++++-
3 files changed, 73 insertions(+), 10 deletions(-)
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 0cdd359..6affdd4 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -355,14 +355,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
omap_up.autosuspend_timeout = info->autosuspend_timeout;
- /* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
- if (!cpu_is_omap2420() && !cpu_is_ti816x())
- omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
-
- /* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
- if (cpu_is_omap34xx() || cpu_is_omap3630())
- omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
-
pdata = &omap_up;
pdata_size = sizeof(struct omap_uart_port_info);
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
index 9ff4444..1a52725 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -65,7 +65,6 @@ struct omap_uart_port_info {
bool dma_enabled; /* To specify DMA Mode */
unsigned int uartclk; /* UART clock rate */
upf_t flags; /* UPF_* flags */
- u32 errata;
unsigned int dma_rx_buf_size;
unsigned int dma_rx_timeout;
unsigned int autosuspend_timeout;
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 0121486..0555c96 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -44,6 +44,13 @@
#include <plat/dmtimer.h>
#include <plat/omap-serial.h>
+#define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
+
+#define OMAP_UART_REV_42 0x0402
+#define OMAP_UART_REV_46 0x0406
+#define OMAP_UART_REV_52 0x0502
+#define OMAP_UART_REV_63 0x0603
+
#define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
/* SCR register bitmasks */
@@ -53,6 +60,17 @@
#define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT 6
#define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
+/* MVR register bitmasks */
+#define OMAP_UART_MVR_SCHEME_SHIFT 30
+
+#define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
+#define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
+#define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
+
+#define OMAP_UART_MVR_MAJ_MASK 0x700
+#define OMAP_UART_MVR_MAJ_SHIFT 8
+#define OMAP_UART_MVR_MIN_MASK 0x3f
+
static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
/* Forward declaration of functions */
@@ -1346,6 +1364,59 @@ static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
return;
}
+static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
+{
+ u32 mvr, scheme;
+ u16 revision, major, minor;
+
+ mvr = serial_in(up, UART_OMAP_MVER);
+
+ /* Check revision register scheme */
+ scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
+
+ switch (scheme) {
+ case 0: /* Legacy Scheme: OMAP2/3 */
+ /* MINOR_REV[0:4], MAJOR_REV[4:7] */
+ major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
+ OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
+ minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
+ break;
+ case 1:
+ /* New Scheme: OMAP4+ */
+ /* MINOR_REV[0:5], MAJOR_REV[8:10] */
+ major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
+ OMAP_UART_MVR_MAJ_SHIFT;
+ minor = (mvr & OMAP_UART_MVR_MIN_MASK);
+ break;
+ default:
+ dev_warn(&up->pdev->dev,
+ "Unknown %s revision, defaulting to highest\n",
+ up->name);
+ /* highest possible revision */
+ major = 0xff;
+ minor = 0xff;
+ }
+
+ /* normalize revision for the driver */
+ revision = UART_BUILD_REVISION(major, minor);
+
+ switch (revision) {
+ case OMAP_UART_REV_46:
+ up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
+ UART_ERRATA_i291_DMA_FORCEIDLE);
+ break;
+ case OMAP_UART_REV_52:
+ up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
+ UART_ERRATA_i291_DMA_FORCEIDLE);
+ break;
+ case OMAP_UART_REV_63:
+ up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
+ break;
+ default:
+ break;
+ }
+}
+
static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
{
struct omap_uart_port_info *omap_up_info;
@@ -1443,7 +1514,6 @@ static int serial_omap_probe(struct platform_device *pdev)
"%d\n", DEFAULT_CLK_SPEED);
}
up->uart_dma.uart_base = mem->start;
- up->errata = omap_up_info->errata;
if (omap_up_info->dma_enabled) {
up->uart_dma.uart_dma_tx = dma_tx->start;
@@ -1473,6 +1543,8 @@ static int serial_omap_probe(struct platform_device *pdev)
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
+ omap_serial_fill_features_erratas(up);
+
ui[up->port.line] = up;
serial_omap_add_console_port(up);
--
1.7.5.4
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags
2012-04-03 13:42 ` [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags Govindraj.R
@ 2012-04-04 14:10 ` Jon Hunter
2012-04-05 11:12 ` Shubhrajyoti
1 sibling, 0 replies; 3+ messages in thread
From: Jon Hunter @ 2012-04-04 14:10 UTC (permalink / raw)
To: Govindraj.R
Cc: linux-omap, linux-serial, linux-arm-kernel, Paul Walmsley,
Kevin Hilman, Felipe Balbi
Hi Govindraj,
On 04/03/2012 08:42 AM, Govindraj.R wrote:
> From: "Govindraj.R"<govindraj.raja@ti.com>
>
> Currently the errata is populated based on cpu checks this can
> be removed and replaced with module version check of uart ip block.
> MVR reg is provided within the uart reg map use the same
> to populate the errata and thus now errata population and handling
> can be managed within the driver itself.
>
> Cc: Jon Hunter<jon-hunter@ti.com>
> Cc: Paul Walmsley<paul@pwsan.com>
> Cc: Kevin Hilman<khilman@ti.com>
> Signed-off-by: Felipe Balbi<balbi@ti.com>
> Signed-off-by: Govindraj.R<govindraj.raja@ti.com>
> ---
> arch/arm/mach-omap2/serial.c | 8 ---
> arch/arm/plat-omap/include/plat/omap-serial.h | 1 -
> drivers/tty/serial/omap-serial.c | 74 ++++++++++++++++++++++++-
> 3 files changed, 73 insertions(+), 10 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
> index 0cdd359..6affdd4 100644
> --- a/arch/arm/mach-omap2/serial.c
> +++ b/arch/arm/mach-omap2/serial.c
> @@ -355,14 +355,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
> omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
> omap_up.autosuspend_timeout = info->autosuspend_timeout;
>
> - /* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
> - if (!cpu_is_omap2420()&& !cpu_is_ti816x())
> - omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
> -
> - /* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
> - if (cpu_is_omap34xx() || cpu_is_omap3630())
> - omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
> -
> pdata =&omap_up;
> pdata_size = sizeof(struct omap_uart_port_info);
>
> diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
> index 9ff4444..1a52725 100644
> --- a/arch/arm/plat-omap/include/plat/omap-serial.h
> +++ b/arch/arm/plat-omap/include/plat/omap-serial.h
> @@ -65,7 +65,6 @@ struct omap_uart_port_info {
> bool dma_enabled; /* To specify DMA Mode */
> unsigned int uartclk; /* UART clock rate */
> upf_t flags; /* UPF_* flags */
> - u32 errata;
> unsigned int dma_rx_buf_size;
> unsigned int dma_rx_timeout;
> unsigned int autosuspend_timeout;
> diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> index 0121486..0555c96 100644
> --- a/drivers/tty/serial/omap-serial.c
> +++ b/drivers/tty/serial/omap-serial.c
> @@ -44,6 +44,13 @@
> #include<plat/dmtimer.h>
> #include<plat/omap-serial.h>
>
> +#define UART_BUILD_REVISION(x, y) (((x)<< 8) | (y))
> +
> +#define OMAP_UART_REV_42 0x0402
> +#define OMAP_UART_REV_46 0x0406
> +#define OMAP_UART_REV_52 0x0502
> +#define OMAP_UART_REV_63 0x0603
> +
> #define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
>
> /* SCR register bitmasks */
> @@ -53,6 +60,17 @@
> #define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT 6
> #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3<< 6)
>
> +/* MVR register bitmasks */
> +#define OMAP_UART_MVR_SCHEME_SHIFT 30
> +
> +#define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
> +#define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
> +#define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
> +
> +#define OMAP_UART_MVR_MAJ_MASK 0x700
> +#define OMAP_UART_MVR_MAJ_SHIFT 8
> +#define OMAP_UART_MVR_MIN_MASK 0x3f
> +
> static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
>
> /* Forward declaration of functions */
> @@ -1346,6 +1364,59 @@ static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
> return;
> }
>
> +static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
> +{
> + u32 mvr, scheme;
> + u16 revision, major, minor;
> +
> + mvr = serial_in(up, UART_OMAP_MVER);
> +
> + /* Check revision register scheme */
> + scheme = mvr>> OMAP_UART_MVR_SCHEME_SHIFT;
> +
> + switch (scheme) {
> + case 0: /* Legacy Scheme: OMAP2/3 */
> + /* MINOR_REV[0:4], MAJOR_REV[4:7] */
> + major = (mvr& OMAP_UART_LEGACY_MVR_MAJ_MASK)>>
> + OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
> + minor = (mvr& OMAP_UART_LEGACY_MVR_MIN_MASK);
> + break;
> + case 1:
> + /* New Scheme: OMAP4+ */
> + /* MINOR_REV[0:5], MAJOR_REV[8:10] */
> + major = (mvr& OMAP_UART_MVR_MAJ_MASK)>>
> + OMAP_UART_MVR_MAJ_SHIFT;
> + minor = (mvr& OMAP_UART_MVR_MIN_MASK);
> + break;
> + default:
> + dev_warn(&up->pdev->dev,
> + "Unknown %s revision, defaulting to highest\n",
> + up->name);
> + /* highest possible revision */
> + major = 0xff;
> + minor = 0xff;
> + }
> +
> + /* normalize revision for the driver */
> + revision = UART_BUILD_REVISION(major, minor);
> +
> + switch (revision) {
> + case OMAP_UART_REV_46:
> + up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
> + UART_ERRATA_i291_DMA_FORCEIDLE);
> + break;
> + case OMAP_UART_REV_52:
> + up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
> + UART_ERRATA_i291_DMA_FORCEIDLE);
> + break;
> + case OMAP_UART_REV_63:
> + up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
> + break;
> + default:
> + break;
> + }
> +}
> +
> static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
> {
> struct omap_uart_port_info *omap_up_info;
> @@ -1443,7 +1514,6 @@ static int serial_omap_probe(struct platform_device *pdev)
> "%d\n", DEFAULT_CLK_SPEED);
> }
> up->uart_dma.uart_base = mem->start;
> - up->errata = omap_up_info->errata;
>
> if (omap_up_info->dma_enabled) {
> up->uart_dma.uart_dma_tx = dma_tx->start;
> @@ -1473,6 +1543,8 @@ static int serial_omap_probe(struct platform_device *pdev)
> pm_runtime_enable(&pdev->dev);
> pm_runtime_get_sync(&pdev->dev);
>
> + omap_serial_fill_features_erratas(up);
> +
> ui[up->port.line] = up;
> serial_omap_add_console_port(up);
>
Thanks!
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Cheers
Jon
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags
2012-04-03 13:42 ` [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags Govindraj.R
2012-04-04 14:10 ` Jon Hunter
@ 2012-04-05 11:12 ` Shubhrajyoti
1 sibling, 0 replies; 3+ messages in thread
From: Shubhrajyoti @ 2012-04-05 11:12 UTC (permalink / raw)
To: Govindraj.R
Cc: linux-omap, linux-serial, linux-arm-kernel, Jon Hunter,
Paul Walmsley, Kevin Hilman, Felipe Balbi
Hi Govind,
On Tuesday 03 April 2012 07:12 PM, Govindraj.R wrote:
> From: "Govindraj.R" <govindraj.raja@ti.com>
>
> Currently the errata is populated based on cpu checks this can
> be removed and replaced with module version check of uart ip block.
> MVR reg is provided within the uart reg map use the same
> to populate the errata and thus now errata population and handling
> can be managed within the driver itself.
>
> Cc: Jon Hunter <jon-hunter@ti.com>
> Cc: Paul Walmsley <paul@pwsan.com>
> Cc: Kevin Hilman <khilman@ti.com>
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
> ---
> arch/arm/mach-omap2/serial.c | 8 ---
> arch/arm/plat-omap/include/plat/omap-serial.h | 1 -
> drivers/tty/serial/omap-serial.c | 74 ++++++++++++++++++++++++-
> 3 files changed, 73 insertions(+), 10 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
> index 0cdd359..6affdd4 100644
> --- a/arch/arm/mach-omap2/serial.c
> +++ b/arch/arm/mach-omap2/serial.c
> @@ -355,14 +355,6 @@ void __init omap_serial_init_port(struct omap_board_data *bdata,
> omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
> omap_up.autosuspend_timeout = info->autosuspend_timeout;
>
> - /* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
> - if (!cpu_is_omap2420() && !cpu_is_ti816x())
> - omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
> -
> - /* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
> - if (cpu_is_omap34xx() || cpu_is_omap3630())
34xx is true for 3630 also thanks for fixing the unneeded oring.
:-)
> - omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
> -
> pdata = &omap_up;
> pdata_size = sizeof(struct omap_uart_port_info);
>
> diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
> index 9ff4444..1a52725 100644
> --- a/arch/arm/plat-omap/include/plat/omap-serial.h
> +++ b/arch/arm/plat-omap/include/plat/omap-serial.h
> @@ -65,7 +65,6 @@ struct omap_uart_port_info {
> bool dma_enabled; /* To specify DMA Mode */
> unsigned int uartclk; /* UART clock rate */
> upf_t flags; /* UPF_* flags */
> - u32 errata;
> unsigned int dma_rx_buf_size;
> unsigned int dma_rx_timeout;
> unsigned int autosuspend_timeout;
> diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> index 0121486..0555c96 100644
> --- a/drivers/tty/serial/omap-serial.c
> +++ b/drivers/tty/serial/omap-serial.c
> @@ -44,6 +44,13 @@
> #include <plat/dmtimer.h>
> #include <plat/omap-serial.h>
>
> +#define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
> +
> +#define OMAP_UART_REV_42 0x0402
> +#define OMAP_UART_REV_46 0x0406
> +#define OMAP_UART_REV_52 0x0502
> +#define OMAP_UART_REV_63 0x0603
Maybe a comment can be added or the #define changed to reflect
the processor also so that it is easy to map.
A dev_info print could be added so that the bootup logs(probe) could
tell what ip rev is booted is running.
Feel free to ignore such trivial comments.
> +
> #define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
>
> /* SCR register bitmasks */
> @@ -53,6 +60,17 @@
> #define OMAP_UART_FCR_RX_FIFO_TRIG_SHIFT 6
> #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
>
> +/* MVR register bitmasks */
> +#define OMAP_UART_MVR_SCHEME_SHIFT 30
> +
> +#define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
> +#define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
> +#define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
> +
> +#define OMAP_UART_MVR_MAJ_MASK 0x700
> +#define OMAP_UART_MVR_MAJ_SHIFT 8
> +#define OMAP_UART_MVR_MIN_MASK 0x3f
> +
> static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
>
> /* Forward declaration of functions */
> @@ -1346,6 +1364,59 @@ static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
> return;
> }
>
> +static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
> +{
> + u32 mvr, scheme;
> + u16 revision, major, minor;
> +
> + mvr = serial_in(up, UART_OMAP_MVER);
> +
> + /* Check revision register scheme */
> + scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
> +
> + switch (scheme) {
> + case 0: /* Legacy Scheme: OMAP2/3 */
> + /* MINOR_REV[0:4], MAJOR_REV[4:7] */
> + major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
> + OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
> + minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
> + break;
> + case 1:
> + /* New Scheme: OMAP4+ */
> + /* MINOR_REV[0:5], MAJOR_REV[8:10] */
> + major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
> + OMAP_UART_MVR_MAJ_SHIFT;
> + minor = (mvr & OMAP_UART_MVR_MIN_MASK);
> + break;
> + default:
> + dev_warn(&up->pdev->dev,
> + "Unknown %s revision, defaulting to highest\n",
> + up->name);
> + /* highest possible revision */
> + major = 0xff;
> + minor = 0xff;
> + }
> +
> + /* normalize revision for the driver */
> + revision = UART_BUILD_REVISION(major, minor);
> +
> + switch (revision) {
> + case OMAP_UART_REV_46:
> + up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
> + UART_ERRATA_i291_DMA_FORCEIDLE);
> + break;
> + case OMAP_UART_REV_52:
> + up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
> + UART_ERRATA_i291_DMA_FORCEIDLE);
> + break;
> + case OMAP_UART_REV_63:
> + up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
> + break;
> + default:
> + break;
> + }
> +}
> +
> static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
> {
> struct omap_uart_port_info *omap_up_info;
> @@ -1443,7 +1514,6 @@ static int serial_omap_probe(struct platform_device *pdev)
> "%d\n", DEFAULT_CLK_SPEED);
> }
> up->uart_dma.uart_base = mem->start;
> - up->errata = omap_up_info->errata;
>
> if (omap_up_info->dma_enabled) {
> up->uart_dma.uart_dma_tx = dma_tx->start;
> @@ -1473,6 +1543,8 @@ static int serial_omap_probe(struct platform_device *pdev)
> pm_runtime_enable(&pdev->dev);
> pm_runtime_get_sync(&pdev->dev);
>
> + omap_serial_fill_features_erratas(up);
Nit : errata ( it is the prural of erratum)
> +
> ui[up->port.line] = up;
> serial_omap_add_console_port(up);
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2012-04-05 11:12 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1333356489-5816-1-git-send-email-govindraj.raja@ti.com>
2012-04-03 13:42 ` [PATCH v3] OMAP2+: UART: Remove cpu checks for populating errata flags Govindraj.R
2012-04-04 14:10 ` Jon Hunter
2012-04-05 11:12 ` Shubhrajyoti
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).