linux-serial.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Akash Asthana <akashast@codeaurora.org>
To: gregkh@linuxfoundation.org
Cc: linux-arm-msm@vger.kernel.org, linux-serial@vger.kernel.org,
	mgautam@codeaurora.org, bjorn.andersson@linaro.org,
	swboyd@chromium.org, Akash Asthana <akashast@codeaurora.org>
Subject: [PATCH V2 2/2] tty: serial: qcom_geni_serial: Wakeup over UART RX
Date: Thu, 10 Oct 2019 15:16:43 +0530	[thread overview]
Message-ID: <1570700803-17566-1-git-send-email-akashast@codeaurora.org> (raw)

Add system wakeup capability over UART RX line for wakeup capable UART.
When system is suspended, RX line act as an interrupt to wakeup system
for any communication requests from peer.

Signed-off-by: Akash Asthana <akashast@codeaurora.org>
---
Changes in v2:
 - Split v1 patch in two.
 - Address review comments v1 patch.

 drivers/tty/serial/qcom_geni_serial.c | 44 ++++++++++++++++++++++++++++++++++-
 1 file changed, 43 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 5180cd8..ff63728 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -14,6 +14,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/qcom-geni-se.h>
 #include <linux/serial.h>
 #include <linux/serial_core.h>
@@ -116,6 +117,7 @@ struct qcom_geni_serial_port {
 	bool brk;
 
 	unsigned int tx_remaining;
+	int wakeup_irq;
 };
 
 static const struct uart_ops qcom_geni_console_pops;
@@ -755,6 +757,15 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
 		uart_write_wakeup(uport);
 }
 
+static irqreturn_t qcom_geni_serial_wakeup_isr(int isr, void *dev)
+{
+	struct uart_port *uport = dev;
+
+	pm_wakeup_event(uport->dev, 2000);
+
+	return IRQ_HANDLED;
+}
+
 static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
 {
 	u32 m_irq_en;
@@ -1306,6 +1317,29 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	if (!console) {
+		port->wakeup_irq = platform_get_irq(pdev, 1);
+		if (port->wakeup_irq < 0) {
+			dev_err(&pdev->dev, "Failed to get wakeup IRQ %d\n",
+					port->wakeup_irq);
+		} else {
+			irq_set_status_flags(port->wakeup_irq, IRQ_NOAUTOEN);
+			ret = devm_request_irq(uport->dev, port->wakeup_irq,
+				qcom_geni_serial_wakeup_isr,
+				IRQF_TRIGGER_FALLING, "uart_wakeup", uport);
+			if (ret) {
+				dev_err(uport->dev, "Failed to register wakeup IRQ ret %d\n",
+						ret);
+				return ret;
+			}
+
+			device_init_wakeup(&pdev->dev, true);
+			ret = dev_pm_set_wake_irq(&pdev->dev, port->wakeup_irq);
+			if (unlikely(ret))
+				dev_err(uport->dev, "%s:Failed to set IRQ wake:%d\n",
+						__func__, ret);
+		}
+	}
 	uport->private_data = drv;
 	platform_set_drvdata(pdev, port);
 	port->handle_rx = console ? handle_rx_console : handle_rx_uart;
@@ -1328,7 +1362,12 @@ static int __maybe_unused qcom_geni_serial_sys_suspend(struct device *dev)
 	struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
 	struct uart_port *uport = &port->uport;
 
-	return uart_suspend_port(uport->private_data, uport);
+	uart_suspend_port(uport->private_data, uport);
+
+	if (port->wakeup_irq > 0)
+		enable_irq(port->wakeup_irq);
+
+	return 0;
 }
 
 static int __maybe_unused qcom_geni_serial_sys_resume(struct device *dev)
@@ -1336,6 +1375,9 @@ static int __maybe_unused qcom_geni_serial_sys_resume(struct device *dev)
 	struct qcom_geni_serial_port *port = dev_get_drvdata(dev);
 	struct uart_port *uport = &port->uport;
 
+	if (port->wakeup_irq > 0)
+		disable_irq(port->wakeup_irq);
+
 	return uart_resume_port(uport->private_data, uport);
 }
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project


             reply	other threads:[~2019-10-10  9:47 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-10  9:46 Akash Asthana [this message]
2019-10-10 14:25 ` [PATCH V2 2/2] tty: serial: qcom_geni_serial: Wakeup over UART RX Stephen Boyd
2019-10-11  9:48   ` Akash Asthana
2019-10-15 20:10     ` Stephen Boyd
2019-10-17 11:10       ` Akash Asthana
2019-10-28 15:00         ` Stephen Boyd
2019-11-05  9:56           ` Akash Asthana

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1570700803-17566-1-git-send-email-akashast@codeaurora.org \
    --to=akashast@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-serial@vger.kernel.org \
    --cc=mgautam@codeaurora.org \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).