* [RFC/CFT] Split 8250 port table
@ 2005-06-23 10:03 Russell King
2005-06-27 10:42 ` [RFC/CFT] Split 8250 port table (part 2) Russell King
0 siblings, 1 reply; 2+ messages in thread
From: Russell King @ 2005-06-23 10:03 UTC (permalink / raw)
To: Linux Kernel List; +Cc: Linux Serial List
Here's a patch which some people may rejoice over, others may groan.
Add separate files for the different 8250 ISA-based serial boards.
Looking across all the various architectures, it seems reasonable that
we can key the availability of the configuration options for these
beasts to the bus-related symbols (iow, CONFIG_ISA). We also standardise
the base baud/uart clock rate for these boards - I'm sure that isn't
architecture specific, but is solely dependent on the crystal fitted
on the board (which should be the same no matter what type of machine
its fitted into.)
The ordering of the ports has been kept the same, provided the modules
are linked into the kernel in the link order specified.
Once this patch has been accepted, we can kill the ISA serial board
static entries in _all_ of the architecture specific serial.h files.
However, the biggest downside to this is the way platform devices with
the same name are handled - they must have a unique ID, which is
hard-coded into the structure.
There appears to be three choices in respect of this:
1. we hard-code the values as below
2. we build into the kernel another object whose sole purpose is to
provide 8250-based platform devices with unique IDs.
3. we fix the platform device layer so that it can look at the ID, and
if its an "allocate me a new number" it scans the platform device
list for the next free ID for that name.
Comments?
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250.c linux/drivers/serial/8250.c
--- orig/drivers/serial/8250.c Sun May 1 20:59:28 2005
+++ linux/drivers/serial/8250.c Wed May 4 13:18:10 2005
@@ -77,23 +77,9 @@ static unsigned int share_irqs = SERIAL8
*/
#define is_real_interrupt(irq) ((irq) != 0)
-/*
- * This converts from our new CONFIG_ symbols to the symbols
- * that asm/serial.h expects. You _NEED_ to comment out the
- * linux/config.h include contained inside asm/serial.h for
- * this to work.
- */
-#undef CONFIG_SERIAL_MANY_PORTS
-#undef CONFIG_SERIAL_DETECT_IRQ
-#undef CONFIG_SERIAL_MULTIPORT
-#undef CONFIG_HUB6
-
#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
#define CONFIG_SERIAL_DETECT_IRQ 1
#endif
-#ifdef CONFIG_SERIAL_8250_MULTIPORT
-#define CONFIG_SERIAL_MULTIPORT 1
-#endif
#ifdef CONFIG_SERIAL_8250_MANY_PORTS
#define CONFIG_SERIAL_MANY_PORTS 1
#endif
@@ -2348,10 +2334,11 @@ static int __devinit serial8250_probe(st
{
struct plat_serial8250_port *p = dev->platform_data;
struct uart_port port;
+ int ret, i;
memset(&port, 0, sizeof(struct uart_port));
- for (; p && p->flags != 0; p++) {
+ for (i = 0; p && p->flags != 0; p++, i++) {
port.iobase = p->iobase;
port.membase = p->membase;
port.irq = p->irq;
@@ -2360,10 +2347,16 @@ static int __devinit serial8250_probe(st
port.iotype = p->iotype;
port.flags = p->flags;
port.mapbase = p->mapbase;
+ port.hub6 = p->hub6;
port.dev = dev;
if (share_irqs)
port.flags |= UPF_SHARE_IRQ;
- serial8250_register_port(&port);
+ ret = serial8250_register_port(&port);
+ if (ret < 0) {
+ dev_err(dev, "unable to register port at index %d "
+ "(IO%lx MEM%lx IRQ%d): %d\n", i,
+ p->iobase, p->mapbase, p->irq, ret);
+ }
}
return 0;
}
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250_accent.c linux/drivers/serial/8250_accent.c
--- orig/drivers/serial/8250_accent.c Thu Jan 1 01:00:00 1970
+++ linux/drivers/serial/8250_accent.c Wed May 4 13:31:09 2005
@@ -0,0 +1,47 @@
+/*
+ * linux/drivers/serial/8250_accent.c
+ *
+ * Copyright (C) 2005 Russell King.
+ * Data taken from include/asm-i386/serial.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+
+#define PORT(_base,_irq) \
+ { \
+ .iobase = _base, \
+ .irq = _irq, \
+ .uartclk = 1843200, \
+ .iotype = UPIO_PORT, \
+ .flags = UPF_BOOT_AUTOCONF, \
+ }
+
+static struct plat_serial8250_port accent_data[] = {
+ PORT(0x330, 4),
+ PORT(0x338, 4),
+ { },
+};
+
+static struct platform_device accent_device = {
+ .name = "serial8250",
+ .id = 2,
+ .dev = {
+ .platform_data = accent_data,
+ },
+};
+
+static int __init accent_init(void)
+{
+ return platform_device_register(&accent_device);
+}
+
+module_init(accent_init);
+
+MODULE_AUTHOR("Russell King");
+MODULE_DESCRIPTION("8250 serial probe module for Accent Async cards");
+MODULE_LICENSE("GPL");
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250_boca.c linux/drivers/serial/8250_boca.c
--- orig/drivers/serial/8250_boca.c Thu Jan 1 01:00:00 1970
+++ linux/drivers/serial/8250_boca.c Wed May 4 13:31:09 2005
@@ -0,0 +1,61 @@
+/*
+ * linux/drivers/serial/8250_boca.c
+ *
+ * Copyright (C) 2005 Russell King.
+ * Data taken from include/asm-i386/serial.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+
+#define PORT(_base,_irq) \
+ { \
+ .iobase = _base, \
+ .irq = _irq, \
+ .uartclk = 1843200, \
+ .iotype = UPIO_PORT, \
+ .flags = UPF_BOOT_AUTOCONF, \
+ }
+
+static struct plat_serial8250_port boca_data[] = {
+ PORT(0x100, 12),
+ PORT(0x108, 12),
+ PORT(0x110, 12),
+ PORT(0x118, 12),
+ PORT(0x120, 12),
+ PORT(0x128, 12),
+ PORT(0x130, 12),
+ PORT(0x138, 12),
+ PORT(0x140, 12),
+ PORT(0x148, 12),
+ PORT(0x150, 12),
+ PORT(0x158, 12),
+ PORT(0x160, 12),
+ PORT(0x168, 12),
+ PORT(0x170, 12),
+ PORT(0x178, 12),
+ { },
+};
+
+static struct platform_device boca_device = {
+ .name = "serial8250",
+ .id = 3,
+ .dev = {
+ .platform_data = boca_data,
+ },
+};
+
+static int __init boca_init(void)
+{
+ return platform_device_register(&boca_device);
+}
+
+module_init(boca_init);
+
+MODULE_AUTHOR("Russell King");
+MODULE_DESCRIPTION("8250 serial probe module for Boca cards");
+MODULE_LICENSE("GPL");
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250_fourport.c linux/drivers/serial/8250_fourport.c
--- orig/drivers/serial/8250_fourport.c Thu Jan 1 01:00:00 1970
+++ linux/drivers/serial/8250_fourport.c Wed May 4 13:31:09 2005
@@ -0,0 +1,53 @@
+/*
+ * linux/drivers/serial/8250_fourport.c
+ *
+ * Copyright (C) 2005 Russell King.
+ * Data taken from include/asm-i386/serial.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+
+#define PORT(_base,_irq) \
+ { \
+ .iobase = _base, \
+ .irq = _irq, \
+ .uartclk = 1843200, \
+ .iotype = UPIO_PORT, \
+ .flags = UPF_BOOT_AUTOCONF | UPF_FOURPORT, \
+ }
+
+static struct plat_serial8250_port fourport_data[] = {
+ PORT(0x1a0, 9),
+ PORT(0x1a8, 9),
+ PORT(0x1b0, 9),
+ PORT(0x1b8, 9),
+ PORT(0x2a0, 5),
+ PORT(0x2a8, 5),
+ PORT(0x2b0, 5),
+ PORT(0x2b8, 5),
+ { },
+};
+
+static struct platform_device fourport_device = {
+ .name = "serial8250",
+ .id = 1,
+ .dev = {
+ .platform_data = fourport_data,
+ },
+};
+
+static int __init fourport_init(void)
+{
+ return platform_device_register(&fourport_device);
+}
+
+module_init(fourport_init);
+
+MODULE_AUTHOR("Russell King");
+MODULE_DESCRIPTION("8250 serial probe module for AST Fourport cards");
+MODULE_LICENSE("GPL");
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250_hub6.c linux/drivers/serial/8250_hub6.c
--- orig/drivers/serial/8250_hub6.c Thu Jan 1 01:00:00 1970
+++ linux/drivers/serial/8250_hub6.c Wed May 4 13:31:09 2005
@@ -0,0 +1,58 @@
+/*
+ * linux/drivers/serial/8250_hub6.c
+ *
+ * Copyright (C) 2005 Russell King.
+ * Data taken from include/asm-i386/serial.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+
+#define HUB6(card,port) \
+ { \
+ .iobase = 0x302, \
+ .irq = 3, \
+ .uartclk = 1843200, \
+ .iotype = UPIO_HUB6, \
+ .flags = UPF_BOOT_AUTOCONF, \
+ .hub6 = (card) << 6 | (port) << 3 | 1, \
+ }
+
+static struct plat_serial8250_port hub6_data[] = {
+ HUB6(0,0),
+ HUB6(0,1),
+ HUB6(0,2),
+ HUB6(0,3),
+ HUB6(0,4),
+ HUB6(0,5),
+ HUB6(1,0),
+ HUB6(1,1),
+ HUB6(1,2),
+ HUB6(1,3),
+ HUB6(1,4),
+ HUB6(1,5),
+ { },
+};
+
+static struct platform_device hub6_device = {
+ .name = "serial8250",
+ .id = 4,
+ .dev = {
+ .platform_data = hub6_data,
+ },
+};
+
+static int __init hub6_init(void)
+{
+ return platform_device_register(&hub6_device);
+}
+
+module_init(hub6_init);
+
+MODULE_AUTHOR("Russell King");
+MODULE_DESCRIPTION("8250 serial probe module for Hub6 cards");
+MODULE_LICENSE("GPL");
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/8250_mca.c linux/drivers/serial/8250_mca.c
--- orig/drivers/serial/8250_mca.c Thu Jan 1 01:00:00 1970
+++ linux/drivers/serial/8250_mca.c Wed May 4 13:31:09 2005
@@ -0,0 +1,64 @@
+/*
+ * linux/drivers/serial/8250_mca.c
+ *
+ * Copyright (C) 2005 Russell King.
+ * Data taken from include/asm-i386/serial.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/mca.h>
+#include <linux/serial_8250.h>
+
+/*
+ * FIXME: Should we be doing AUTO_IRQ here?
+ */
+#ifdef CONFIG_SERIAL_8250_DETECT_IRQ
+#define MCA_FLAGS UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ
+#else
+#define MCA_FLAGS UPF_BOOT_AUTOCONF | UPF_SKIP_TEST
+#endif
+
+#define PORT(_base,_irq) \
+ { \
+ .iobase = _base, \
+ .irq = _irq, \
+ .uartclk = 1843200, \
+ .iotype = UPIO_PORT, \
+ .flags = MCA_FLAGS, \
+ }
+
+static struct plat_serial8250_port mca_data[] = {
+ PORT(0x3220, 3),
+ PORT(0x3228, 3),
+ PORT(0x4220, 3),
+ PORT(0x4228, 3),
+ PORT(0x5220, 3),
+ PORT(0x5228, 3),
+ { },
+};
+
+static struct platform_device mca_device = {
+ .name = "serial8250",
+ .id = 5,
+ .dev = {
+ .platform_data = mca_data,
+ },
+};
+
+static int __init mca_init(void)
+{
+ if (!MCA_bus)
+ return -ENODEV;
+ return platform_device_register(&mca_device);
+}
+
+module_init(mca_init);
+
+MODULE_AUTHOR("Russell King");
+MODULE_DESCRIPTION("8250 serial probe module for MCA ports");
+MODULE_LICENSE("GPL");
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x *.orig -x *.rej -x .git orig/drivers/serial/Kconfig linux/drivers/serial/Kconfig
--- orig/drivers/serial/Kconfig Sun May 1 08:07:54 2005
+++ linux/drivers/serial/Kconfig Wed May 4 13:38:46 2005
@@ -89,11 +89,11 @@ config SERIAL_8250_NR_UARTS
int "Maximum number of non-legacy 8250/16550 serial ports"
depends on SERIAL_8250
default "4"
- ---help---
- Set this to the number of non-legacy serial ports you want
- the driver to support. This includes any ports discovered
- via ACPI or PCI enumeration and any ports that may be added
- at run-time via hot-plug.
+ help
+ Set this to the number of serial ports you want the driver
+ to support. This includes any ports discovered via ACPI or
+ PCI enumeration and any ports that may be added at run-time
+ via hot-plug, or any ISA multi-port serial cards.
config SERIAL_8250_EXTENDED
bool "Extended 8250/16550 serial driver options"
@@ -141,31 +141,74 @@ config SERIAL_8250_DETECT_IRQ
If unsure, say N.
-config SERIAL_8250_MULTIPORT
- bool "Support special multiport boards"
- depends on SERIAL_8250_EXTENDED
- help
- Some multiport serial ports have special ports which are used to
- signal when there are any serial ports on the board which need
- servicing. Say Y here to enable the serial driver to take advantage
- of those special I/O ports.
-
config SERIAL_8250_RSA
bool "Support RSA serial ports"
depends on SERIAL_8250_EXTENDED
help
::: To be written :::
-comment "Non-8250 serial port support"
+#
+# Multi-port serial cards
+#
+
+config SERIAL_8250_FOURPORT
+ tristate "Support Fourport cards"
+ depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
+ help
+ Say Y here if you have an AST FourPort serial board.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_fourport.
+
+config SERIAL_8250_ACCENT
+ tristate "Support Accent cards"
+ depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
+ help
+ Say Y here if you have an Accent Async serial board.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_accent.
+
+
+config SERIAL_8250_BOCA
+ tristate "Support Boca cards"
+ depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
+ help
+ Say Y here if you have a Boca serial board. Please read the Boca
+ mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto>
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_boca.
+
+
+config SERIAL_8250_HUB6
+ tristate "Support Hub6 cards"
+ depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
+ help
+ Say Y here if you have a HUB6 serial board.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_hub6.
+
+config SERIAL_8250_MCA
+ tristate "Support 8250-type ports on MCA buses"
+ depends on SERIAL_8250 != n && MCA
+ help
+ Say Y here if you have a MCA serial ports.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_mca.
config SERIAL_8250_ACORN
tristate "Acorn expansion card serial port support"
- depends on ARM && ARCH_ACORN && SERIAL_8250
+ depends on ARCH_ACORN && SERIAL_8250
help
If you have an Atomwide Serial card or Serial Port card for an Acorn
system, say Y to this option. The driver can handle 1, 2, or 3 port
cards. If unsure, say N.
+comment "Non-8250 serial port support"
+
config SERIAL_AMBA_PL010
tristate "ARM AMBA PL010 serial port support"
depends on ARM_AMBA
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x '*.orig' -x '*.rej' -x .git -N orig/drivers/serial/Makefile linux/drivers/serial/Makefile
--- orig/drivers/serial/Makefile Sun May 1 08:07:54 2005
+++ linux/drivers/serial/Makefile Wed May 4 11:23:11 2005
@@ -17,6 +17,11 @@ obj-$(CONFIG_SERIAL_8250) += 8250.o $(se
obj-$(CONFIG_SERIAL_8250_CS) += serial_cs.o
obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
obj-$(CONFIG_SERIAL_8250_CONSOLE) += 8250_early.o
+obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o
+obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o
+obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o
+obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
diff -up -x BitKeeper -x ChangeSet -x SCCS -x _xlk -x *.orig -x *.rej -x .git orig/include/linux/serial_8250.h linux/include/linux/serial_8250.h
--- orig/include/linux/serial_8250.h Sun May 1 08:11:18 2005
+++ linux/include/linux/serial_8250.h Wed May 4 12:31:24 2005
@@ -22,6 +22,7 @@ struct plat_serial8250_port {
unsigned int uartclk; /* UART clock rate */
unsigned char regshift; /* register shift */
unsigned char iotype; /* UPIO_* */
+ unsigned char hub6;
unsigned int flags; /* UPF_* flags */
};
--
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 Serial core
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [RFC/CFT] Split 8250 port table (part 2)
2005-06-23 10:03 [RFC/CFT] Split 8250 port table Russell King
@ 2005-06-27 10:42 ` Russell King
0 siblings, 0 replies; 2+ messages in thread
From: Russell King @ 2005-06-27 10:42 UTC (permalink / raw)
To: Linux Kernel List, Linux Serial List
On Thu, Jun 23, 2005 at 11:03:37AM +0100, Russell King wrote:
> Add separate files for the different 8250 ISA-based serial boards.
Ok, I've now committed this to my git tree. Here's the second part
to this.
What this change means is that you must set SERIAL_8250_NR_UARTS to
the total number of 8250-based UARTs you want to support, not the
number of _extra_ ports. Hopefully, I've correctly updated those
defconfig files which have been impacted by this change.
The only ports which remain in asm-*/serial.h are the platform specific
entries. These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c
Index: arch/parisc/configs/712_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/712_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/712_defconfig (mode:100644)
@@ -506,7 +506,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/a500_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/a500_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/a500_defconfig (mode:100644)
@@ -662,7 +662,7 @@
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_CS=m
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/b180_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/b180_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/b180_defconfig (mode:100644)
@@ -514,7 +514,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/configs/c3000_defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/configs/c3000_defconfig (mode:100644)
+++ uncommitted/arch/parisc/configs/c3000_defconfig (mode:100644)
@@ -661,7 +661,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: arch/parisc/defconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/arch/parisc/defconfig (mode:100644)
+++ uncommitted/arch/parisc/defconfig (mode:100644)
@@ -517,7 +517,7 @@
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
Index: drivers/serial/8250.c
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/drivers/serial/8250.c (mode:100644)
+++ uncommitted/drivers/serial/8250.c (mode:100644)
@@ -105,7 +105,7 @@
SERIAL_PORT_DFNS /* defined in asm/serial.h */
};
-#define UART_NR (ARRAY_SIZE(old_serial_port) + CONFIG_SERIAL_8250_NR_UARTS)
+#define UART_NR CONFIG_SERIAL_8250_NR_UARTS
#ifdef CONFIG_SERIAL_8250_RSA
Index: drivers/serial/Kconfig
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/drivers/serial/Kconfig (mode:100644)
+++ uncommitted/drivers/serial/Kconfig (mode:100644)
@@ -86,7 +86,7 @@
namespace, say Y here. If unsure, say N.
config SERIAL_8250_NR_UARTS
- int "Maximum number of non-legacy 8250/16550 serial ports"
+ int "Maximum number of 8250/16550 serial ports"
depends on SERIAL_8250
default "4"
help
Index: include/asm-alpha/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-alpha/serial.h (mode:100644)
+++ uncommitted/include/asm-alpha/serial.h (mode:100644)
@@ -22,54 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#endif
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
Index: include/asm-arm26/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-arm26/serial.h (mode:100644)
+++ uncommitted/include/asm-arm26/serial.h (mode:100644)
@@ -30,34 +30,16 @@
#if defined(CONFIG_ARCH_A5K)
/* UART CLK PORT IRQ FLAGS */
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
{ 0, BASE_BAUD, 0x3F8, 10, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 10, STD_COM_FLAGS }, /* ttyS1 */
#else
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
{ 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS1 */
#endif
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS2 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS3 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS13 */
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
-
#endif
Index: include/asm-i386/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-i386/serial.h (mode:100644)
+++ uncommitted/include/asm-i386/serial.h (mode:100644)
@@ -22,109 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#ifdef CONFIG_MCA
-#define MCA_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
-#else
-#define MCA_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
-
Index: include/asm-m68k/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-m68k/serial.h (mode:100644)
+++ uncommitted/include/asm-m68k/serial.h (mode:100644)
@@ -26,54 +26,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#endif
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS
Index: include/asm-mips/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-mips/serial.h (mode:100644)
+++ uncommitted/include/asm-mips/serial.h (mode:100644)
@@ -29,32 +29,6 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#define RS_TABLE_SIZE 64
-#else
-#define RS_TABLE_SIZE
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
#ifdef CONFIG_MACH_JAZZ
#include <asm/jazz.h>
@@ -240,66 +214,10 @@
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else /* CONFIG_SERIAL_MANY_PORTS */
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif /* CONFIG_SERIAL_MANY_PORTS */
-
#else /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
#define STD_SERIAL_PORT_DEFNS
-#define EXTRA_SERIAL_PORT_DEFNS
#endif /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
#ifdef CONFIG_MOMENCO_JAGUAR_ATX
/* Ordinary NS16552 duart with a 20MHz crystal. */
#define JAGUAR_ATX_UART_CLK 20000000
@@ -427,8 +345,6 @@
COBALT_SERIAL_PORT_DEFNS \
DDB5477_SERIAL_PORT_DEFNS \
EV96100_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
IP32_SERIAL_PORT_DEFNS \
ITE_SERIAL_PORT_DEFNS \
IVR_SERIAL_PORT_DEFNS \
Index: include/asm-parisc/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-parisc/serial.h (mode:100644)
+++ uncommitted/include/asm-parisc/serial.h (mode:100644)
@@ -19,18 +19,4 @@
* A500 w/ PCI serial cards: 5 + 4 * card ~= 17
*/
-#define STD_SERIAL_PORT_DEFNS \
- { 0, }, /* ttyS0 */ \
- { 0, }, /* ttyS1 */ \
- { 0, }, /* ttyS2 */ \
- { 0, }, /* ttyS3 */ \
- { 0, }, /* ttyS4 */ \
- { 0, }, /* ttyS5 */ \
- { 0, }, /* ttyS6 */ \
- { 0, }, /* ttyS7 */ \
- { 0, }, /* ttyS8 */
-
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS
-
+#define SERIAL_PORT_DFNS
Index: include/asm-ppc/pc_serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-ppc/pc_serial.h (mode:100644)
+++ uncommitted/include/asm-ppc/pc_serial.h (mode:100644)
@@ -35,93 +35,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS
Index: include/asm-sh/bigsur/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/bigsur/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/bigsur/serial.h (mode:100644)
@@ -14,13 +14,10 @@
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */
-
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-sh/ec3104/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/ec3104/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/ec3104/serial.h (mode:100644)
@@ -10,13 +10,11 @@
* it's got the keyboard controller behind it so we can't really use it
* (without moving the keyboard driver to userspace, which doesn't sound
* like a very good idea) */
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x11C00, EC3104_IRQBASE+7, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x12000, EC3104_IRQBASE+8, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x12400, EC3104_IRQBASE+9, STD_COM_FLAGS }, /* ttyS2 */
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-sh/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh/serial.h (mode:100644)
+++ uncommitted/include/asm-sh/serial.h (mode:100644)
@@ -29,20 +29,18 @@
#ifdef CONFIG_HD64465
#include <asm/hd64465.h>
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */
#else
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */
#endif
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
#endif
#endif /* _ASM_SERIAL_H */
Index: include/asm-sh64/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-sh64/serial.h (mode:100644)
+++ uncommitted/include/asm-sh64/serial.h (mode:100644)
@@ -20,13 +20,11 @@
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
/* XXX: This should be moved ino irq.h */
#define irq_cannonicalize(x) (x)
Index: include/asm-x86_64/serial.h
===================================================================
--- 61f26f0bd348c6ddac8b3b1105e00fa790ea3ea6/include/asm-x86_64/serial.h (mode:100644)
+++ uncommitted/include/asm-x86_64/serial.h (mode:100644)
@@ -22,109 +22,9 @@
#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
#endif
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
+#define SERIAL_PORT_DFNS \
/* UART CLK PORT IRQ FLAGS */ \
{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
{ 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
{ 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
-#endif
-
-#ifdef CONFIG_MCA
-#define MCA_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
- { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
-#else
-#define MCA_SERIAL_PORT_DFNS
-#endif
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
-
--
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 Serial core
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2005-06-27 10:42 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-06-23 10:03 [RFC/CFT] Split 8250 port table Russell King
2005-06-27 10:42 ` [RFC/CFT] Split 8250 port table (part 2) Russell King
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).