From mboxrd@z Thu Jan 1 00:00:00 1970 From: Sasha Levin Subject: [PATCH AUTOSEL 4.19 008/101] tty: serial: cpm_uart - fix init when SMC is relocated Date: Fri, 19 Jul 2019 00:05:59 -0400 Message-ID: <20190719040732.17285-8-sashal@kernel.org> References: <20190719040732.17285-1-sashal@kernel.org> Mime-Version: 1.0 Content-Transfer-Encoding: 8bit Return-path: In-Reply-To: <20190719040732.17285-1-sashal@kernel.org> Sender: linux-kernel-owner@vger.kernel.org To: linux-kernel@vger.kernel.org, stable@vger.kernel.org Cc: Christophe Leroy , Greg Kroah-Hartman , Sasha Levin , linux-serial@vger.kernel.org List-Id: linux-serial@vger.kernel.org From: Christophe Leroy [ Upstream commit 06aaa3d066db87e8478522d910285141d44b1e58 ] SMC relocation can also be activated earlier by the bootloader, so the driver's behaviour cannot rely on selected kernel config. When the SMC is relocated, CPM_CR_INIT_TRX cannot be used. But the only thing CPM_CR_INIT_TRX does is to clear the rstate and tstate registers, so this can be done manually, even when SMC is not relocated. Signed-off-by: Christophe Leroy Fixes: 9ab921201444 ("cpm_uart: fix non-console port startup bug") Signed-off-by: Greg Kroah-Hartman Signed-off-by: Sasha Levin --- drivers/tty/serial/cpm_uart/cpm_uart_core.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-) diff --git a/drivers/tty/serial/cpm_uart/cpm_uart_core.c b/drivers/tty/serial/cpm_uart/cpm_uart_core.c index e5389591bb4f..ad40c75bb58f 100644 --- a/drivers/tty/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/tty/serial/cpm_uart/cpm_uart_core.c @@ -407,7 +407,16 @@ static int cpm_uart_startup(struct uart_port *port) clrbits16(&pinfo->sccp->scc_sccm, UART_SCCM_RX); } cpm_uart_initbd(pinfo); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + if (IS_SMC(pinfo)) { + out_be32(&pinfo->smcup->smc_rstate, 0); + out_be32(&pinfo->smcup->smc_tstate, 0); + out_be16(&pinfo->smcup->smc_rbptr, + in_be16(&pinfo->smcup->smc_rbase)); + out_be16(&pinfo->smcup->smc_tbptr, + in_be16(&pinfo->smcup->smc_tbase)); + } else { + cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); + } } /* Install interrupt handler. */ retval = request_irq(port->irq, cpm_uart_int, 0, "cpm_uart", port); @@ -861,16 +870,14 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) (u8 __iomem *)pinfo->tx_bd_base - DPRAM_BASE); /* - * In case SMC1 is being relocated... + * In case SMC is being relocated... */ -#if defined (CONFIG_I2C_SPI_SMC1_UCODE_PATCH) out_be16(&up->smc_rbptr, in_be16(&pinfo->smcup->smc_rbase)); out_be16(&up->smc_tbptr, in_be16(&pinfo->smcup->smc_tbase)); out_be32(&up->smc_rstate, 0); out_be32(&up->smc_tstate, 0); out_be16(&up->smc_brkcr, 1); /* number of break chars */ out_be16(&up->smc_brkec, 0); -#endif /* Set up the uart parameters in the * parameter ram. @@ -884,8 +891,6 @@ static void cpm_uart_init_smc(struct uart_cpm_port *pinfo) out_be16(&up->smc_brkec, 0); out_be16(&up->smc_brkcr, 1); - cpm_line_cr_cmd(pinfo, CPM_CR_INIT_TRX); - /* Set UART mode, 8 bit, no parity, one stop. * Enable receive and transmit. */ -- 2.20.1