[PATCH v2 1/2] dt-bindings: serial: lpuart: add ls1028a compatibility

[PATCH v2 1/2] dt-bindings: serial: lpuart: add ls1028a compatibility

[Michael Walle]

Add the LS1028A SoC compatibility string to the lpuart devicetree
bindings documentation.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
---
changes since v1:
 - add changelog text

 .../devicetree/bindings/serial/fsl-lpuart.txt          | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
index c904e2e68332..e7448b92dd9d 100644
--- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt
@@ -6,6 +6,8 @@ Required properties:
     on Vybrid vf610 SoC with 8-bit register organization
   - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated
     on LS1021A SoC with 32-bit big-endian register organization
+  - "fsl,ls1028a-lpuart" for lpuart compatible with the one integrated
+    on LS1028A SoC with 32-bit little-endian register organization
   - "fsl,imx7ulp-lpuart" for lpuart compatible with the one integrated
     on i.MX7ULP SoC with 32-bit little-endian register organization
   - "fsl,imx8qxp-lpuart" for lpuart compatible with the one integrated
@@ -15,10 +17,10 @@ Required properties:
 - reg : Address and length of the register set for the device
 - interrupts : Should contain uart interrupt
 - clocks : phandle + clock specifier pairs, one for each entry in clock-names
-- clock-names : For vf610/ls1021a/imx7ulp, "ipg" clock is for uart bus/baud
-  clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used to access
-  lpuart controller registers, it also requires "baud" clock for module to
-  receive/transmit data.
+- clock-names : For vf610/ls1021a/ls1028a/imx7ulp, "ipg" clock is for uart
+  bus/baud clock. For imx8qxp lpuart, "ipg" clock is bus clock that is used
+  to access lpuart controller registers, it also requires "baud" clock for
+  module to receive/transmit data.
 
 Optional properties:
 - dmas: A list of two dma specifiers, one for each entry in dma-names.
-- 
2.20.1

[PATCH v2 2/2] arm64: dts: ls1028a: add missing LPUART nodes

[Michael Walle]

The LS1028A has six LPUART controllers. Add the nodes.

This was tested on a custom board.

Signed-off-by: Michael Walle <michael@walle.cc>
---
changes since v1:
 - none

 .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 73 +++++++++++++++++++
 1 file changed, 73 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 41c9633293fb..b152fa90cf5c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -372,6 +372,79 @@
 			status = "disabled";
 		};
 
+
+		lpuart0: serial@2260000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2260000 0x0 0x1000>;
+			interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 32>,
+			       <&edma0 1 33>;
+			status = "disabled";
+		};
+
+		lpuart1: serial@2270000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2270000 0x0 0x1000>;
+			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 30>,
+			       <&edma0 1 31>;
+			status = "disabled";
+		};
+
+		lpuart2: serial@2280000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2280000 0x0 0x1000>;
+			interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 28>,
+			       <&edma0 1 29>;
+			status = "disabled";
+		};
+
+		lpuart3: serial@2290000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x2290000 0x0 0x1000>;
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 26>,
+			       <&edma0 1 27>;
+			status = "disabled";
+		};
+
+		lpuart4: serial@22a0000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x22a0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 24>,
+			       <&edma0 1 25>;
+			status = "disabled";
+		};
+
+		lpuart5: serial@22b0000 {
+			compatible = "fsl,ls1028a-lpuart";
+			reg = <0x0 0x22b0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen 4 1>;
+			clock-names = "ipg";
+			dma-names = "rx","tx";
+			dmas = <&edma0 1 22>,
+			       <&edma0 1 23>;
+			status = "disabled";
+		};
+
 		edma0: dma-controller@22c0000 {
 			#dma-cells = <2>;
 			compatible = "fsl,ls1028a-edma";
-- 
2.20.1