[PATCH AUTOSEL 5.10 027/116] tty: serial: imx: disable UCR4_OREN in .stop_rx() instead of .shutdown()

[PATCH AUTOSEL 5.10 027/116] tty: serial: imx: disable UCR4_OREN in .stop_rx() instead of .shutdown()

[Sasha Levin]

From: Fugang Duan <fugang.duan@nxp.com>

[ Upstream commit 028e083832b06fdeeb290e1e57dc1f6702c4c215 ]

The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().

Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller.  Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/imx.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 28cc328ddb6eb..93cd8ad57f385 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -508,18 +508,21 @@ static void imx_uart_stop_tx(struct uart_port *port)
 static void imx_uart_stop_rx(struct uart_port *port)
 {
 	struct imx_port *sport = (struct imx_port *)port;
-	u32 ucr1, ucr2;
+	u32 ucr1, ucr2, ucr4;
 
 	ucr1 = imx_uart_readl(sport, UCR1);
 	ucr2 = imx_uart_readl(sport, UCR2);
+	ucr4 = imx_uart_readl(sport, UCR4);
 
 	if (sport->dma_is_enabled) {
 		ucr1 &= ~(UCR1_RXDMAEN | UCR1_ATDMAEN);
 	} else {
 		ucr1 &= ~UCR1_RRDYEN;
 		ucr2 &= ~UCR2_ATEN;
+		ucr4 &= ~UCR4_OREN;
 	}
 	imx_uart_writel(sport, ucr1, UCR1);
+	imx_uart_writel(sport, ucr4, UCR4);
 
 	ucr2 &= ~UCR2_RXEN;
 	imx_uart_writel(sport, ucr2, UCR2);
@@ -1576,7 +1579,7 @@ static void imx_uart_shutdown(struct uart_port *port)
 	imx_uart_writel(sport, ucr1, UCR1);
 
 	ucr4 = imx_uart_readl(sport, UCR4);
-	ucr4 &= ~(UCR4_OREN | UCR4_TCEN);
+	ucr4 &= ~UCR4_TCEN;
 	imx_uart_writel(sport, ucr4, UCR4);
 
 	spin_unlock_irqrestore(&sport->port.lock, flags);
-- 
2.34.1

[PATCH AUTOSEL 5.10 110/116] serial: pl010: Drop CR register reset on set_termios

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 08a0c6dff91c965e39905cf200d22db989203ccb ]

pl010_set_termios() briefly resets the CR register to zero.

Where does this register write come from?

The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock.  ambauart_set_termios() also
modified that register.  To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts.  That is achieved by
writing zero to the CR register.

However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591

That rendered the CR register write obsolete.  Drop it.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/amba-pl010.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/tty/serial/amba-pl010.c b/drivers/tty/serial/amba-pl010.c
index 3284f34e9dfe1..75d61e038a775 100644
--- a/drivers/tty/serial/amba-pl010.c
+++ b/drivers/tty/serial/amba-pl010.c
@@ -448,14 +448,11 @@ pl010_set_termios(struct uart_port *port, struct ktermios *termios,
 	if ((termios->c_cflag & CREAD) == 0)
 		uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
 
-	/* first, disable everything */
 	old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
 
 	if (UART_ENABLE_MS(port, termios->c_cflag))
 		old_cr |= UART010_CR_MSIE;
 
-	writel(0, uap->port.membase + UART010_CR);
-
 	/* Set baud rate */
 	quot -= 1;
 	writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
-- 
2.34.1

[PATCH AUTOSEL 5.10 111/116] serial: core: Keep mctrl register state and cached copy in sync

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 93a770b7e16772530196674ffc79bb13fa927dc6 ]

struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state.  It also avoids a register
read to obtain the current state of output signals.

When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync.  That may cause
a subsequent register write to be incorrectly skipped.  Fix it before
it trips somebody up.

This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb

So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup().  Therefore,
a stable designation seems unnecessary.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/serial_core.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 046bedca7b8f5..55108db5b64bf 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -2414,7 +2414,8 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 		 * We probably don't need a spinlock around this, but
 		 */
 		spin_lock_irqsave(&port->lock, flags);
-		port->ops->set_mctrl(port, port->mctrl & TIOCM_DTR);
+		port->mctrl &= TIOCM_DTR;
+		port->ops->set_mctrl(port, port->mctrl);
 		spin_unlock_irqrestore(&port->lock, flags);
 
 		/*
-- 
2.34.1