[PATCH 0/4] serial: Patches for OCTEON CPU support (version 2).

[PATCH 0/4] serial: Patches for OCTEON CPU support (version 2).

[David Daney]

The previous patch set was Signed-off-by: Andrew Morton and added to
the -mm tree, however comments from Shinya Kuribayashi prompted me to
make some improvements.

The first three patches are unchanged from the previous set (I hope it
is not a breach of etiquette to include them again).  The forth which
allows uart bug types to be statically specified is completely
removed.  And the fifth (now forth) is simplified and now only adds a
uart type for the OCTEON uart.

And as I previously said:
Since these are the only non-mips specific patches required for OCTEON
cpu support, it is necessary to get these Signed-off-by before the
full OCTEON patch set can proceed.


Four patches to follow.

Thanks,

David Daney (4):
   8250: Don't clobber spinlocks.
   8250: Serial driver changes to support future Cavium OCTEON serial
     patches.
   Serial: Allow port type to be specified when calling
     serial8250_register_port.
   Serial: UART driver changes for Cavium OCTEON.

  drivers/serial/8250.c        |  225 
+++++++++++++++++++++++++++++++-----------
  drivers/serial/serial_core.c |    7 +-
  include/linux/serial_8250.h  |    3 +
  include/linux/serial_core.h  |    7 +-
  4 files changed, 179 insertions(+), 63 deletions(-)

[PATCH 1/4] 8250: Don't clobber spinlocks.

[David Daney]

In serial8250_isa_init_ports(), the port's lock is initialized.  We
should not overwrite it.  In early_serial_setup(), only copy in the
fields we need.  Since the early console code only uses a subset of
the fields, these are sufficient.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
 drivers/serial/8250.c |   15 +++++++++++++--
 1 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 303272a..8e28750 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -2752,12 +2752,23 @@ static struct uart_driver serial8250_reg = {
  */
 int __init early_serial_setup(struct uart_port *port)
 {
+	struct uart_port *p;
+
 	if (port->line >= ARRAY_SIZE(serial8250_ports))
 		return -ENODEV;
 
 	serial8250_isa_init_ports();
-	serial8250_ports[port->line].port	= *port;
-	serial8250_ports[port->line].port.ops	= &serial8250_pops;
+	p = &serial8250_ports[port->line].port;
+	p->iobase       = port->iobase;
+	p->membase      = port->membase;
+	p->irq          = port->irq;
+	p->uartclk      = port->uartclk;
+	p->fifosize     = port->fifosize;
+	p->regshift     = port->regshift;
+	p->iotype       = port->iotype;
+	p->flags        = port->flags;
+	p->mapbase      = port->mapbase;
+	p->private_data = port->private_data;
 	return 0;
 }
 
-- 
1.5.6.5

Re: [PATCH 1/4] 8250: Don't clobber spinlocks.

[Alan Cox]

On Mon,  1 Dec 2008 15:49:25 -0800
David Daney <ddaney@caviumnetworks.com> wrote:

> In serial8250_isa_init_ports(), the port's lock is initialized.  We
> should not overwrite it.  In early_serial_setup(), only copy in the
> fields we need.  Since the early console code only uses a subset of
> the fields, these are sufficient.

> -	serial8250_ports[port->line].port.ops	= &serial8250_pops;

You seem to drop the assignment of port.ops ?

Re: [PATCH 1/4] 8250: Don't clobber spinlocks.

[David Daney]

Alan Cox wrote:
> On Mon,  1 Dec 2008 15:49:25 -0800
> David Daney <ddaney@caviumnetworks.com> wrote:
> 
>> In serial8250_isa_init_ports(), the port's lock is initialized.  We
>> should not overwrite it.  In early_serial_setup(), only copy in the
>> fields we need.  Since the early console code only uses a subset of
>> the fields, these are sufficient.
> 
>> -	serial8250_ports[port->line].port.ops	= &serial8250_pops;
> 
> You seem to drop the assignment of port.ops ?
> 

The port.ops are initialized in the preceding call to 
serial8250_isa_init_ports(), we don't have to set it again as we are no 
longer clobbering it with a full structure assignment.

Perhaps the patch commentary should be adjusted to mention this.

David Daney

[PATCH 2/4] 8250: Serial driver changes to support future Cavium OCTEON serial patches.

[David Daney]

In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions.  Compatible
I/O functions are added for existing iotypeS.

An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.

The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
 drivers/serial/8250.c       |  194 ++++++++++++++++++++++++++++++-------------
 include/linux/serial_8250.h |    2 +
 include/linux/serial_core.h |    2 +
 3 files changed, 140 insertions(+), 58 deletions(-)

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 8e28750..849af9d 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -303,16 +303,16 @@ static const u8 au_io_out_map[] = {
 };
 
 /* sane hardware needs no mapping */
-static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+static inline int map_8250_in_reg(struct uart_port *p, int offset)
 {
-	if (up->port.iotype != UPIO_AU)
+	if (p->iotype != UPIO_AU)
 		return offset;
 	return au_io_in_map[offset];
 }
 
-static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+static inline int map_8250_out_reg(struct uart_port *p, int offset)
 {
-	if (up->port.iotype != UPIO_AU)
+	if (p->iotype != UPIO_AU)
 		return offset;
 	return au_io_out_map[offset];
 }
@@ -341,16 +341,16 @@ static const u8
 		[UART_SCR]	= 0x2c
 	};
 
-static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+static inline int map_8250_in_reg(struct uart_port *p, int offset)
 {
-	if (up->port.iotype != UPIO_RM9000)
+	if (p->iotype != UPIO_RM9000)
 		return offset;
 	return regmap_in[offset];
 }
 
-static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+static inline int map_8250_out_reg(struct uart_port *p, int offset)
 {
-	if (up->port.iotype != UPIO_RM9000)
+	if (p->iotype != UPIO_RM9000)
 		return offset;
 	return regmap_out[offset];
 }
@@ -363,108 +363,170 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
 
 #endif
 
-static unsigned int serial_in(struct uart_8250_port *up, int offset)
+static unsigned int hub6_serial_in(struct uart_port *p, int offset)
 {
-	unsigned int tmp;
-	offset = map_8250_in_reg(up, offset) << up->port.regshift;
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	outb(p->hub6 - 1 + offset, p->iobase);
+	return inb(p->iobase + 1);
+}
 
-	switch (up->port.iotype) {
-	case UPIO_HUB6:
-		outb(up->port.hub6 - 1 + offset, up->port.iobase);
-		return inb(up->port.iobase + 1);
+static void hub6_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	outb(p->hub6 - 1 + offset, p->iobase);
+	outb(value, p->iobase + 1);
+}
 
-	case UPIO_MEM:
-	case UPIO_DWAPB:
-		return readb(up->port.membase + offset);
+static unsigned int mem_serial_in(struct uart_port *p, int offset)
+{
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	return readb(p->membase + offset);
+}
 
-	case UPIO_RM9000:
-	case UPIO_MEM32:
-		return readl(up->port.membase + offset);
+static void mem_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	writeb(value, p->membase + offset);
+}
+
+static void mem32_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	writel(value, p->membase + offset);
+}
+
+static unsigned int mem32_serial_in(struct uart_port *p, int offset)
+{
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	return readl(p->membase + offset);
+}
 
 #ifdef CONFIG_SERIAL_8250_AU1X00
-	case UPIO_AU:
-		return __raw_readl(up->port.membase + offset);
+static unsigned int au_serial_in(struct uart_port *p, int offset)
+{
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	return __raw_readl(p->membase + offset);
+}
+
+static void au_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	__raw_writel(value, p->membase + offset);
+}
 #endif
 
-	case UPIO_TSI:
-		if (offset == UART_IIR) {
-			tmp = readl(up->port.membase + (UART_IIR & ~3));
-			return (tmp >> 16) & 0xff; /* UART_IIR % 4 == 2 */
-		} else
-			return readb(up->port.membase + offset);
+static unsigned int tsi_serial_in(struct uart_port *p, int offset)
+{
+	unsigned int tmp;
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	if (offset == UART_IIR) {
+		tmp = readl(p->membase + (UART_IIR & ~3));
+		return (tmp >> 16) & 0xff; /* UART_IIR % 4 == 2 */
+	} else
+		return readb(p->membase + offset);
+}
 
-	default:
-		return inb(up->port.iobase + offset);
-	}
+static void tsi_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	if (!((offset == UART_IER) && (value & UART_IER_UUE)))
+		writeb(value, p->membase + offset);
 }
 
-static void
-serial_out(struct uart_8250_port *up, int offset, int value)
+static void dwapb_serial_out(struct uart_port *p, int offset, int value)
 {
-	/* Save the offset before it's remapped */
 	int save_offset = offset;
-	offset = map_8250_out_reg(up, offset) << up->port.regshift;
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	/* Save the LCR value so it can be re-written when a
+	 * Busy Detect interrupt occurs. */
+	if (save_offset == UART_LCR) {
+		struct uart_8250_port *up = (struct uart_8250_port *)p;
+		up->lcr = value;
+	}
+	writeb(value, p->membase + offset);
+	/* Read the IER to ensure any interrupt is cleared before
+	 * returning from ISR. */
+	if (save_offset == UART_TX || save_offset == UART_IER)
+		value = p->serial_in(p, UART_IER);
+}
 
-	switch (up->port.iotype) {
+static unsigned int io_serial_in(struct uart_port *p, int offset)
+{
+	offset = map_8250_in_reg(p, offset) << p->regshift;
+	return inb(p->iobase + offset);
+}
+
+static void io_serial_out(struct uart_port *p, int offset, int value)
+{
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	outb(value, p->iobase + offset);
+}
+
+static void set_io_from_upio(struct uart_port *p)
+{
+	switch (p->iotype) {
 	case UPIO_HUB6:
-		outb(up->port.hub6 - 1 + offset, up->port.iobase);
-		outb(value, up->port.iobase + 1);
+		p->serial_in = hub6_serial_in;
+		p->serial_out = hub6_serial_out;
 		break;
 
 	case UPIO_MEM:
-		writeb(value, up->port.membase + offset);
+		p->serial_in = mem_serial_in;
+		p->serial_out = mem_serial_out;
 		break;
 
 	case UPIO_RM9000:
 	case UPIO_MEM32:
-		writel(value, up->port.membase + offset);
+		p->serial_in = mem32_serial_in;
+		p->serial_out = mem32_serial_out;
 		break;
 
 #ifdef CONFIG_SERIAL_8250_AU1X00
 	case UPIO_AU:
-		__raw_writel(value, up->port.membase + offset);
+		p->serial_in = au_serial_in;
+		p->serial_out = au_serial_out;
 		break;
 #endif
 	case UPIO_TSI:
-		if (!((offset == UART_IER) && (value & UART_IER_UUE)))
-			writeb(value, up->port.membase + offset);
+		p->serial_in = tsi_serial_in;
+		p->serial_out = tsi_serial_out;
 		break;
 
 	case UPIO_DWAPB:
-		/* Save the LCR value so it can be re-written when a
-		 * Busy Detect interrupt occurs. */
-		if (save_offset == UART_LCR)
-			up->lcr = value;
-		writeb(value, up->port.membase + offset);
-		/* Read the IER to ensure any interrupt is cleared before
-		 * returning from ISR. */
-		if (save_offset == UART_TX || save_offset == UART_IER)
-			value = serial_in(up, UART_IER);
+		p->serial_in = mem_serial_in;
+		p->serial_out = dwapb_serial_out;
 		break;
 
 	default:
-		outb(value, up->port.iobase + offset);
+		p->serial_in = io_serial_in;
+		p->serial_out = io_serial_out;
+		break;
 	}
 }
 
 static void
 serial_out_sync(struct uart_8250_port *up, int offset, int value)
 {
-	switch (up->port.iotype) {
+	struct uart_port *p = &up->port;
+	switch (p->iotype) {
 	case UPIO_MEM:
 	case UPIO_MEM32:
 #ifdef CONFIG_SERIAL_8250_AU1X00
 	case UPIO_AU:
 #endif
 	case UPIO_DWAPB:
-		serial_out(up, offset, value);
-		serial_in(up, UART_LCR);	/* safe, no side-effects */
+		p->serial_out(p, offset, value);
+		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
 		break;
 	default:
-		serial_out(up, offset, value);
+		p->serial_out(p, offset, value);
 	}
 }
 
+#define serial_in(up, offset)		\
+	(up->port.serial_in(&(up)->port, (offset)))
+#define serial_out(up, offset, value)	\
+	(up->port.serial_out(&(up)->port, (offset), (value)))
 /*
  * We used to support using pause I/O for certain machines.  We
  * haven't supported this for a while, but just in case it's badly
@@ -2576,6 +2638,7 @@ static void __init serial8250_isa_init_ports(void)
 		up->port.membase  = old_serial_port[i].iomem_base;
 		up->port.iotype   = old_serial_port[i].io_type;
 		up->port.regshift = old_serial_port[i].iomem_reg_shift;
+		set_io_from_upio(&up->port);
 		if (share_irqs)
 			up->port.flags |= UPF_SHARE_IRQ;
 	}
@@ -2769,6 +2832,13 @@ int __init early_serial_setup(struct uart_port *port)
 	p->flags        = port->flags;
 	p->mapbase      = port->mapbase;
 	p->private_data = port->private_data;
+
+	set_io_from_upio(p);
+	if (port->serial_in)
+		p->serial_in = port->serial_in;
+	if (port->serial_out)
+		p->serial_out = port->serial_out;
+
 	return 0;
 }
 
@@ -2833,6 +2903,8 @@ static int __devinit serial8250_probe(struct platform_device *dev)
 		port.mapbase		= p->mapbase;
 		port.hub6		= p->hub6;
 		port.private_data	= p->private_data;
+		port.serial_in		= p->serial_in;
+		port.serial_out		= p->serial_out;
 		port.dev		= &dev->dev;
 		if (share_irqs)
 			port.flags |= UPF_SHARE_IRQ;
@@ -2986,6 +3058,12 @@ int serial8250_register_port(struct uart_port *port)
 		uart->port.private_data = port->private_data;
 		if (port->dev)
 			uart->port.dev = port->dev;
+		set_io_from_upio(&uart->port);
+		/* Possibly override default I/O functions.  */
+		if (port->serial_in)
+			uart->port.serial_in = port->serial_in;
+		if (port->serial_out)
+			uart->port.serial_out = port->serial_out;
 
 		ret = uart_add_one_port(&serial8250_reg, &uart->port);
 		if (ret == 0)
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 3d37c94..77d83d9 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -28,6 +28,8 @@ struct plat_serial8250_port {
 	unsigned char	iotype;		/* UPIO_* */
 	unsigned char	hub6;
 	upf_t		flags;		/* UPF_* flags */
+	unsigned int	(*serial_in)(struct uart_port *, int);
+	void		(*serial_out)(struct uart_port *, int, int);
 };
 
 /*
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 4e4f127..2d22c67 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -246,6 +246,8 @@ struct uart_port {
 	spinlock_t		lock;			/* port lock */
 	unsigned long		iobase;			/* in/out[bwl] */
 	unsigned char __iomem	*membase;		/* read/write[bwl] */
+	unsigned int		(*serial_in)(struct uart_port *, int);
+	void			(*serial_out)(struct uart_port *, int, int);
 	unsigned int		irq;			/* irq number */
 	unsigned int		uartclk;		/* base uart clock */
 	unsigned int		fifosize;		/* tx fifo size */
-- 
1.5.6.5

[PATCH 3/4] Serial: Allow port type to be specified when calling serial8250_register_port.

[David Daney]

Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed.  For this case the UARTs properties
are just copied out of the uart_config entry.

This allows us to keep SOC specific 8250 probe code out of 8250.c.  In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.

The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
 drivers/serial/8250.c        |    9 +++++++++
 drivers/serial/serial_core.c |    7 +++++--
 include/linux/serial_8250.h  |    1 +
 include/linux/serial_core.h  |    2 ++
 4 files changed, 17 insertions(+), 2 deletions(-)

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 849af9d..3ae4974 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -2903,6 +2903,7 @@ static int __devinit serial8250_probe(struct platform_device *dev)
 		port.mapbase		= p->mapbase;
 		port.hub6		= p->hub6;
 		port.private_data	= p->private_data;
+		port.type		= p->type;
 		port.serial_in		= p->serial_in;
 		port.serial_out		= p->serial_out;
 		port.dev		= &dev->dev;
@@ -3058,6 +3059,14 @@ int serial8250_register_port(struct uart_port *port)
 		uart->port.private_data = port->private_data;
 		if (port->dev)
 			uart->port.dev = port->dev;
+
+		if (port->flags & UPF_FIXED_TYPE) {
+			uart->port.type = port->type;
+			uart->port.fifosize = uart_config[port->type].fifo_size;
+			uart->capabilities = uart_config[port->type].flags;
+			uart->tx_loadsz = uart_config[port->type].tx_loadsz;
+		}
+
 		set_io_from_upio(&uart->port);
 		/* Possibly override default I/O functions.  */
 		if (port->serial_in)
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index 874786a..7fef45e 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2198,11 +2198,14 @@ uart_configure_port(struct uart_driver *drv, struct uart_state *state,
 	 * Now do the auto configuration stuff.  Note that config_port
 	 * is expected to claim the resources and map the port for us.
 	 */
-	flags = UART_CONFIG_TYPE;
+	flags = 0;
 	if (port->flags & UPF_AUTO_IRQ)
 		flags |= UART_CONFIG_IRQ;
 	if (port->flags & UPF_BOOT_AUTOCONF) {
-		port->type = PORT_UNKNOWN;
+		if (!(port->flags & UPF_FIXED_TYPE)) {
+			port->type = PORT_UNKNOWN;
+			flags |= UART_CONFIG_TYPE;
+		}
 		port->ops->config_port(port, flags);
 	}
 
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 77d83d9..d4d2a78 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -28,6 +28,7 @@ struct plat_serial8250_port {
 	unsigned char	iotype;		/* UPIO_* */
 	unsigned char	hub6;
 	upf_t		flags;		/* UPF_* flags */
+	unsigned int	type;		/* If UPF_FIXED_TYPE */
 	unsigned int	(*serial_in)(struct uart_port *, int);
 	void		(*serial_out)(struct uart_port *, int, int);
 };
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 2d22c67..b9e7756 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -293,6 +293,8 @@ struct uart_port {
 #define UPF_MAGIC_MULTIPLIER	((__force upf_t) (1 << 16))
 #define UPF_CONS_FLOW		((__force upf_t) (1 << 23))
 #define UPF_SHARE_IRQ		((__force upf_t) (1 << 24))
+/* The exact UART type is known and should not be probed.  */
+#define UPF_FIXED_TYPE		((__force upf_t) (1 << 27))
 #define UPF_BOOT_AUTOCONF	((__force upf_t) (1 << 28))
 #define UPF_FIXED_PORT		((__force upf_t) (1 << 29))
 #define UPF_DEAD		((__force upf_t) (1 << 30))
-- 
1.5.6.5

[PATCH 4/4] Serial: UART driver changes for Cavium OCTEON.

[David Daney]

Cavium UART implementation is not covered by existing uart_configS.
Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
platform device registration code.

Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
---
 drivers/serial/8250.c       |    7 +++++++
 include/linux/serial_core.h |    3 ++-
 2 files changed, 9 insertions(+), 1 deletions(-)

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 3ae4974..daa0056 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -279,6 +279,13 @@ static const struct serial8250_config uart_config[] = {
 		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_OCTEON] = {
+		.name		= "OCTEON",
+		.fifo_size	= 64,
+		.tx_loadsz	= 64,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+		.flags		= UART_CAP_FIFO,
+	},
 };
 
 #if defined (CONFIG_SERIAL_8250_AU1X00)
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index b9e7756..fd772b5 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -40,7 +40,8 @@
 #define PORT_NS16550A	14
 #define PORT_XSCALE	15
 #define PORT_RM9000	16	/* PMC-Sierra RM9xxx internal UART */
-#define PORT_MAX_8250	16	/* max port ID */
+#define PORT_OCTEON	17	/* Cavium OCTEON internal UART */
+#define PORT_MAX_8250	17	/* max port ID */
 
 /*
  * ARM specific type numbers.  These are not currently guaranteed
-- 
1.5.6.5

Re: [PATCH 4/4] Serial: UART driver changes for Cavium OCTEON.

[Alan Cox]

On Mon,  1 Dec 2008 15:49:28 -0800
David Daney <ddaney@caviumnetworks.com> wrote:

> Cavium UART implementation is not covered by existing uart_configS.
> Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
> platform device registration code.

All 4 queued