From: Martin Mokrejs <mmokrejs-08dBlVkRsZWoiTQjSSYKZesEoJ4y9sgM@public.gmane.org>
To: "linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org"
<linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org,
linux-serial-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: 3.4-rc5: usbserial pl2303 attached via Texas Instruments USB3.0 chip Oopses
Date: Wed, 02 May 2012 11:57:26 +0200 [thread overview]
Message-ID: <4FA10506.7020203@fold.natur.cuni.cz> (raw)
[-- Attachment #1: Type: text/plain, Size: 11399 bytes --]
Hi,
I am trying to setup a remote serial console on my Dell Vostro 3550 laptop.
I have some USB to serial dongle which has Prolific 2303 chipset, and works.
I have statically in my kernel:
USB_SERIAL=y
USB_SERIAL_CONSOLE=y
CONFIG_USB_SERIAL_PL2303=y
The problem is that when I attach the dongle to USB3.0 controller linux crashes.
It does not happen if I attach it to EHCI controller (like shown in lsub output at
the end of this email).
I have attached a camera pciture of the stacktrace, but here are few function names
from it:
queue_work_on
queue_work
schedule_work
tty_flip_buffer_push
pl2303_process_read_urb
usb_serial_generic_read_bulk_callback
usb_hcd_giveback_urb
xhci_irq
? _raw_spin_lock_irqsave
xhci_msi_irq
handle_irq_event_percpu
? read_tsc
handle_irq_event
? ack_APIC_irq
handle_edge_irq
handle_irq
do_IRQ
common_interrupt
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
Subsystem: Dell Device 04b3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f08000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00: 86 80 2d 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 80 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
Subsystem: Dell Device 04b3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7f07000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP+
Kernel driver in use: ehci_hcd
00: 86 80 26 1c 06 00 90 02 05 20 03 0c 00 00 00 00
10: 00 70 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00
0b:00.0 USB controller: Texas Instruments Device 8241 (rev 02) (prog-if 30 [XHCI])
Subsystem: Dell Device 04b3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at f7d10000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [c0] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=2 offset=00000000
PBA: BAR=2 offset=00001000
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Device Serial Number 08-00-28-00-00-20-00-00
Kernel driver in use: xhci_hcd
00: 4c 10 41 82 06 04 10 00 02 30 03 0c 10 00 00 00
10: 04 00 d0 f7 00 00 00 00 04 00 d1 f7 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 b3 04
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
# lsusb
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 007: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 003: ID 05ca:1820 Ricoh Co., Ltd
Bus 002 Device 003: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 002 Device 004: ID 138a:0011 Validity Sensors, Inc. VFS5011 Fingerprint Reader
Bus 002 Device 005: ID 0bda:0138 Realtek Semiconductor Corp. Card reader
Bus 001 Device 008: ID 04f2:0116 Chicony Electronics Co., Ltd KU-2971/KU-0325 Keyboard
Bus 001 Device 010: ID 07b4:0105 Olympus Optical Co., Ltd Camedia C-310Z/C-700/C-750UZ/C-755/C-765UZ/C-3040/C-4000/C-5050Z/D-560/C-3020Z Zoom Camera
Bus 001 Device 009: ID 046d:c050 Logitech, Inc. RX 250 Optical Mouse
# lsusb -t
/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci_hcd/2p, 480M
|__ Port 1: Dev 2, If 0, Class=hub, Driver=hub/8p, 480M
|__ Port 2: Dev 3, If 0, Class=vend., Driver=pl2303, 12M
|__ Port 3: Dev 4, If 0, Class=vend., Driver=, 12M
|__ Port 6: Dev 5, If 0, Class=stor., Driver=usb-storage, 480M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci_hcd/2p, 480M
|__ Port 1: Dev 2, If 0, Class=hub, Driver=hub/6p, 480M
|__ Port 1: Dev 7, If 0, Class=hub, Driver=hub/4p, 480M
|__ Port 1: Dev 8, If 0, Class=HID, Driver=usbhid, 1.5M
|__ Port 2: Dev 10, If 0, Class=stor., Driver=usb-storage, 12M
|__ Port 3: Dev 9, If 0, Class=HID, Driver=usbhid, 1.5M
|__ Port 5: Dev 3, If 0, Class='bInterfaceClass 0x0e not yet handled', Driver=uvcvideo, 480M
|__ Port 5: Dev 3, If 1, Class='bInterfaceClass 0x0e not yet handled', Driver=uvcvideo, 480M
#
Bus 002 Device 003: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x067b Prolific Technology, Inc.
idProduct 0x2303 PL2303 Serial Port
bcdDevice 3.00
iManufacturer 1 Prolific Technology Inc.
iProduct 2 USB-Serial Controller
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Thanks for your help,
Martin
[-- Attachment #2: 3.4-rc5-PL2303-via-xHCI-Oops_1024px.jpg --]
[-- Type: image/jpeg, Size: 161338 bytes --]
next reply other threads:[~2012-05-02 9:57 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-05-02 9:57 Martin Mokrejs [this message]
2012-05-02 10:08 ` 3.4-rc5: usbserial pl2303 attached via Texas Instruments USB3.0 chip Oopses Oliver Neukum
2012-05-02 10:21 ` Martin Mokrejs
[not found] ` <4FA10AC6.8030809-08dBlVkRsZWoiTQjSSYKZesEoJ4y9sgM@public.gmane.org>
2012-05-02 10:22 ` Oliver Neukum
[not found] ` <201205021222.30133.oneukum-l3A5Bk7waGM@public.gmane.org>
2012-05-02 10:48 ` Martin Mokrejs
2012-05-02 12:44 ` Oliver Neukum
2012-05-02 23:46 ` Sarah Sharp
2012-05-03 9:14 ` Martin Mokrejs
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4FA10506.7020203@fold.natur.cuni.cz \
--to=mmokrejs-08dblvkrszwoitqjssykzeseoj4y9sgm@public.gmane.org \
--cc=gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org \
--cc=linux-serial-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).