messages from 2026-10-15 12:44:49 to 2026-10-17 10:49:14 UTC [more...]
[PATCH v4 0/4] rust: serdev: Refactor
2026-10-17 10:49 UTC (12+ messages)
` [PATCH v4 1/4] tty: serdev: Add mutex lock
` [PATCH v4 2/4] tty: serdev: Export functions to pause receive_buf callback calls
` [PATCH v4 3/4] rust: serdev: Replace `active` mutex with receive pause
` [PATCH v4 4/4] rust: serdev: Simplify callbacks
[PATCH v2 0/2] serial: amba-pl011: fix RS485 state on enable and reconfiguration
2026-10-17 9:07 UTC (6+ messages)
` [PATCH v2 1/2] serial: amba-pl011: finish a transmission still running when RS485 is enabled
` [PATCH v2 2/2] serial: amba-pl011: keep RS485 transmission running on reconfiguration
[PATCH 0/2] serial: sifive: fix two init ordering bugs in probe
2026-10-17 7:51 UTC (5+ messages)
` [PATCH 1/2] serial: sifive: fix NULL pointer dereference in probe IRQ window
` [PATCH 2/2] serial: sifive: avoid division by zero in the clock notifier
[tty:tty-next] BUILD SUCCESS WITH UNVERIFIED WARNING 1184f87e2790e8af9be3116f608d2e86b4792d7d
2026-10-17 4:32 UTC
[PATCH] MIPS: SGI-IP27: print the NMI dump on an nbcon console
2026-10-16 21:45 UTC (5+ messages)
[PATCH 1/2] tty: serial: remove hub6 multiport support
2026-10-16 18:28 UTC (14+ messages)
` [PATCH 2/2] [v2] serial: 8250: remove obsolete and broken PORT_RSA support
[PATCH RESEND v4] ACPI: SPCR: Support UART clock frequency field
2026-10-16 18:17 UTC (2+ messages)
[PATCH v2 0/7] vt: Simplify console-blanking interface
2026-10-16 10:38 UTC (15+ messages)
` [PATCH v2 1/7] vt: Add con_unblank callback to struct consw
` [PATCH v2 2/7] dummycon: Implement struct consw.con_unblank
` [PATCH v2 3/7] fbcon: "
` [PATCH v2 4/7] newport_con: "
` [PATCH v2 5/7] sticon: "
` [PATCH v2 6/7] vgacon: "
` [PATCH v2 7/7] vt: Remove old-style con_blank
[PATCH 00/11] Add NVIDIA LSTP USB adapter drivers
2026-10-16 9:28 UTC (13+ messages)
` [PATCH 10/11] tty: Add NVIDIA LSTP UART driver
[PATCH 0/2] serial: amba-pl011: fix RS485 state on enable and reconfiguration
2026-10-16 7:54 UTC (5+ messages)
` [PATCH 1/2] serial: amba-pl011: finish a transmission still running when RS485 is enabled
` [PATCH 2/2] serial: amba-pl011: keep RS485 transmission running on reconfiguration
[PATCH v2] tty: sysrq: reset the per-device key state when reparsing reset_seq
2026-10-16 7:19 UTC (2+ messages)
[PATCH] Input: sysrq - reset the per-device key state when reparsing reset_seq
2026-10-16 5:38 UTC (4+ messages)
[PATCH 0/5] serial: mcf: add devicetree support
2026-10-15 22:39 UTC (11+ messages)
` [PATCH 4/5] dt-bindings: serial: create binding for mcf-uart
[PATCH v6 00/10] ARM: Add support for Cortina Systems CS75xx and Securifi Almond+
2026-10-15 20:02 UTC (3+ messages)
` [PATCH v6 03/10] dt-bindings: arm: cpus: Add Cortina Systems CS7542 enable method
[PATCH 0/4] tty: serial: qcom_geni_serial: Add GPI DMA support
2026-10-15 17:06 UTC (7+ messages)
` [PATCH 1/4] dmaengine: qcom: gpi: Add UART transfer support
` [PATCH 4/4] tty: serial: qcom_geni_serial: Add GPI DMA support
[PATCH v8 0/2] serial: core: fix baud rate fallback loop and baud_base overflow
2026-10-15 15:34 UTC (3+ messages)
` [PATCH v8 2/2] serial: core: reject baud_base values that overflow port->uartclk in uart_set_info()
[PATCH] serial: imx: keep the CPU out of deep idle while an RS485 port is open
2026-10-15 15:24 UTC (3+ messages)
[PATCH v3 0/8] soc: qcom: geni: Derive SE clock configuration from OPP table on SA8255P
2026-10-15 13:24 UTC (17+ messages)
` [PATCH v3 1/8] soc: qcom: geni-se: Populate clk_perf_tbl with SE source clock frequencies from perf OPP table
` [PATCH v3 2/8] soc: qcom: geni-se: Add helper to set SE clock rate via OPP
` [PATCH v3 3/8] soc: qcom: geni-se: Remove OPP rate reset from resource deactivation
` [PATCH v3 4/8] serial: qcom-geni: Use geni_se_set_rate() for source clock configuration
` [PATCH v3 5/8] spi: qcom-geni: Use geni_se_set_rate() for setting source clock frequency
` [PATCH v3 6/8] i2c: qcom-geni: Vote for SE clock rate using OPP
` [PATCH v3 7/8] i2c: qcom-geni: Use common GENI resource initialization helper
` [PATCH v3 8/8] i2c: qcom-geni: Use geni_se_set_rate() for setting source clock frequency
page: | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox