Re: [PATCH 0/3] Handle UART without interrupt on TEMT using em485

[Giulio Benetti <giulio.benetti@micronovasrl.com>]

Il 02/02/2021 01:02, Eric Tremblay ha scritto:
> On 2021-01-28 7:12 p.m., Giulio Benetti wrote:
>> Hi Eric,
>>
>>> Il giorno 29 gen 2021, alle ore 00:37, Eric Tremblay <etremblay@distech-controls.com> ha scritto:
>>>
>>> The series is mainly about the support of 8250 UART without TEMT
>>> interrupt. I saw that there was some development in the past but
>>> it was never merged. Since the last discussion were quite some
>>> time ago, I was not sure if I should post a v4 over the
>>> last v3 or start from scratch so I decided to post a new patch. Please
>>> advice if I should have done the reverse.
>> Please keep my and Heiko’s SoB and add your SoB too describing between [ ] what Heiko has done and what you’ve done.
>> For example:
>> SoB: Giulio
>> SoB: Heiko
>> [Heiko: ...]
>> SoB Eric
>> [Eric: improved timeout etc.]
> 
> I will add them in the next version, thanks for mentioning it.

Thank you

>>
>>> The approach is a little different from the last proposed patch which was
>>> doing using a polling at 100us. I tought that it could be really long on
>>> some fast baudrate and really not that long on slow baudrate. The current
>>> approach is to calculate the time of a bytes when the settings are changed.
>>> When we get the interrupt for the empty FIFO, it's the longer it can take
>>> to empty the shift register.
>> Good idea.
>>
>>> The other two patches are to use that features with the PORT_16550A_FSL64
>>> found on some chip like the LS1043A.
>> Do you mind to add my 8250_dw patch that was originally part of this patchset? I had to send it
>> soon, you’ve preceded me :-)
> 
> I think there was still a comment pending on that patch. I think you should resubmit
> since I think it's a bit out-of-scope for me.

Ah yes, you're correct, I will submit it then.

Best regards
-- 
Giulio Benetti
CTO

MICRONOVA SRL
Sede: Via A. Niedda 3 - 35010 Vigonza (PD)
Tel. 049/8931563 - Fax 049/8931346
Cod.Fiscale - P.IVA 02663420285
Capitale Sociale € 26.000 i.v.
Iscritta al Reg. Imprese di Padova N. 02663420285
Numero R.E.A. 258642

>>
>> Thank you
>> Best regards
>> Giulio
>>
>>> Thanks
>>>
>>> Eric Tremblay (3):
>>> serial: 8250: Handle UART without interrupt on TEMT using em485
>>> serial: 8250: add compatible for fsl,16550-FIFO64
>>> serial: 8250: remove UART_CAP_TEMT on PORT_16550A_FSL64
>>>
>>> drivers/tty/serial/8250/8250.h            |  1 +
>>> drivers/tty/serial/8250/8250_bcm2835aux.c |  2 +-
>>> drivers/tty/serial/8250/8250_of.c         |  5 ++
>>> drivers/tty/serial/8250/8250_omap.c       |  2 +-
>>> drivers/tty/serial/8250/8250_port.c       | 89 ++++++++++++++++++++++-
>>> include/linux/serial_8250.h               |  2 +
>>> 6 files changed, 98 insertions(+), 3 deletions(-)
>>>
>>> -- 
>>> 2.17.1
> 
>