Re: [PATCH v8 10/11] tty: serial: Add Nuvoton ma35d1 serial driver support

[Jacky Huang <ychuang570808@gmail.com>]

On 2023/4/25 下午 06:38, Christophe JAILLET wrote:
> Le 25/04/2023 à 12:24, Jacky Huang a écrit :
>> From: Jacky Huang <ychuang3@nuvoton.com>
>>
>> This adds UART and console driver for Nuvoton ma35d1 Soc.
>> It supports full-duplex communication, FIFO control, and
>> hardware flow control.
>>
>> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
>> ---
>>   drivers/tty/serial/Kconfig         |  18 +
>>   drivers/tty/serial/Makefile        |   1 +
>>   drivers/tty/serial/ma35d1_serial.c | 781 +++++++++++++++++++++++++++++
>>   3 files changed, 800 insertions(+)
>>   create mode 100644 drivers/tty/serial/ma35d1_serial.c
>>
>
> [...]
>
>> +static int ma35d1serial_probe(struct platform_device *pdev)
>> +{
>> +    struct resource *res_mem;
>> +    struct uart_ma35d1_port *up;
>> +    int ret = 0;
>> +    struct clk *clk;
>> +    int err;
>> +
>> +    if (pdev->dev.of_node) {
>> +        ret = of_alias_get_id(pdev->dev.of_node, "serial");
>> +        if (ret < 0) {
>> +            dev_err(&pdev->dev, "failed to get alias/pdev id, errno 
>> %d\n", ret);
>> +            return ret;
>> +        }
>> +    }
>> +    up = &ma35d1serial_ports[ret];
>> +    up->port.line = ret;
>> +    res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +    if (!res_mem)
>> +        return -ENODEV;
>> +
>> +    up->port.iobase = res_mem->start;
>> +    up->port.membase = devm_ioremap(&pdev->dev, up->port.iobase, 
>> UART_REG_SIZE);
>> +    up->port.ops = &ma35d1serial_ops;
>> +
>> +    spin_lock_init(&up->port.lock);
>> +
>> +    clk = of_clk_get(pdev->dev.of_node, 0);
>
> Does this...
>
>> +    if (IS_ERR(clk)) {
>> +        err = PTR_ERR(clk);
>> +        dev_err(&pdev->dev, "failed to get core clk: %d\n", err);
>> +        return -ENOENT;
>> +    }
>> +
>> +    err = clk_prepare_enable(clk);
>
> ... and this be undone in the remove function?
>
> CJ
>

I will add clk_disable_unprepare() in the remove function.

>> +    if (err)
>> +        return -ENOENT;
>> +
>> +    if (up->port.line != 0)
>> +        up->port.uartclk = clk_get_rate(clk);
>> +
>> +    ret = platform_get_irq(pdev, 0);
>> +    if (ret < 0)
>> +        return ret;
>> +    up->port.irq = ret;
>> +    up->port.dev = &pdev->dev;
>> +    up->port.flags = UPF_BOOT_AUTOCONF;
>> +
>> +    platform_set_drvdata(pdev, up);
>> +
>> +    return uart_add_one_port(&ma35d1serial_reg, &up->port);
>> +}
>
> [...]
>

Best Regards,
Jacky Huang