* Re: [PATCH v3 07/33] nds32: MMU initialization
From: Greentime Hu @ 2017-12-18 11:21 UTC (permalink / raw)
To: Guo Ren
Cc: Greentime, Linux Kernel Mailing List, Arnd Bergmann, linux-arch,
Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring, netdev,
Vincent Chen, DTML, Al Viro, David Howells, Will Deacon,
Daniel Lezcano, linux-serial-u79uwXL29TY76Z2rM5mHXA,
Geert Uytterhoeven, Linus Walleij, Mark Rutland, Greg KH
In-Reply-To: <20171218090848.GA5823@gary-OptiPlex-3050>
Hi, Guo Ren:
2017-12-18 17:08 GMT+08:00 Guo Ren <ren_guo-Y+KPrCd2zL4AvxtiuMwx3w@public.gmane.org>:
> Hi Greentime,
>
> On Fri, Dec 08, 2017 at 05:11:50PM +0800, Greentime Hu wrote:
> [...]
>>
>> diff --git a/arch/nds32/mm/highmem.c b/arch/nds32/mm/highmem.c
> [...]
>> +void *kmap(struct page *page)
>> +{
>> + unsigned long vaddr;
>> + might_sleep();
>> + if (!PageHighMem(page))
>> + return page_address(page);
>> + vaddr = (unsigned long)kmap_high(page);
> Here should invalid the cpu_mmu_tlb's entry, Or invalid it in the
> set_pte().
>
> eg:
> vaddr0 = kmap(page0)
> *vaddr0 = val0 //It will cause tlb-miss, and hard-refill to MMU-tlb
> kunmap(page0)
> vaddr1 = kmap(page1) // Mostly vaddr1 = vaddr0
> val = vaddr1; //No tlb-miss and it will get page0's val not page1, because
> last expired vaddr0's entry is left in CPU-MMU-tlb.
>
Thanks.
I will add __nds32__tlbop_inv(vaddr); to invalidate this mapping
before retrun vaddr.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v4 16/36] nds32: System calls handling
From: Arnd Bergmann @ 2017-12-18 11:19 UTC (permalink / raw)
To: Greentime Hu
Cc: Greentime, Linux Kernel Mailing List, linux-arch, Thomas Gleixner,
Jason Cooper, Marc Zyngier, Rob Herring, Networking, Vincent Chen,
DTML, Al Viro, David Howells, Will Deacon, Daniel Lezcano,
linux-serial-u79uwXL29TY76Z2rM5mHXA, Geert Uytterhoeven,
Linus Walleij, Mark Rutland, Greg KH,
ren_guo-Y+KPrCd2zL4AvxtiuMwx3w, Philip
In-Reply-To: <9663cb7c21011cdb4f278c1fad081d1df296daa8.1513577007.git.green.hu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
On Mon, Dec 18, 2017 at 7:46 AM, Greentime Hu <green.hu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> new file mode 100644
> index 0000000..90da745
> --- /dev/null
> +++ b/arch/nds32/include/uapi/asm/unistd.h
> @@ -0,0 +1,12 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (C) 2005-2017 Andes Technology Corporation
> +
> +#define __ARCH_WANT_SYNC_FILE_RANGE2
> +
> +/* Use the standard ABI for syscalls */
> +#include <asm-generic/unistd.h>
> +
> +/* Additional NDS32 specific syscalls. */
> +#define __NR_cacheflush (__NR_arch_specific_syscall)
> +#define __NR__llseek __NR_llseek
> +__SYSCALL(__NR_cacheflush, sys_cacheflush)
I'm still confused by __NR__llseek here, why do you need that one?
> +SYSCALL_DEFINE6(mmap2, unsigned long, addr, unsigned long, len,
> + unsigned long, prot, unsigned long, flags,
> + unsigned long, fd, unsigned long, pgoff)
> +{
> + if (pgoff & (~PAGE_MASK >> 12))
> + return -EINVAL;
> +
> + return sys_mmap_pgoff(addr, len, prot, flags, fd,
> + pgoff >> (PAGE_SHIFT - 12));
> +}
> +
> +SYSCALL_DEFINE6(mmap, unsigned long, addr, unsigned long, len,
> + unsigned long, prot, unsigned long, flags,
> + unsigned long, fd, unsigned long, pgoff)
> +{
> + if (unlikely(pgoff & ~PAGE_MASK))
> + return -EINVAL;
> +
> + return sys_mmap_pgoff(addr, len, prot, flags, fd,
> + pgoff >> PAGE_SHIFT);
> +}
And I don't see why you define sys_mmap() in addition to sys_mmap2().
The rest of the syscall handling looks good now.
Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v4 25/36] nds32: Miscellaneous header files
From: Arnd Bergmann @ 2017-12-18 11:13 UTC (permalink / raw)
To: Greentime Hu
Cc: Greentime, Linux Kernel Mailing List, linux-arch, Thomas Gleixner,
Jason Cooper, Marc Zyngier, Rob Herring, Networking, Vincent Chen,
DTML, Al Viro, David Howells, Will Deacon, Daniel Lezcano,
linux-serial-u79uwXL29TY76Z2rM5mHXA, Geert Uytterhoeven,
Linus Walleij, Mark Rutland, Greg KH,
ren_guo-Y+KPrCd2zL4AvxtiuMwx3w, Philip
In-Reply-To: <a5dc2090640500d88aa3af2f6fe9e4c73f0634f2.1513577007.git.green.hu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
On Mon, Dec 18, 2017 at 7:46 AM, Greentime Hu <green.hu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> From: Greentime Hu <greentime-MUIXKm3Oiri1Z/+hSey0Gg@public.gmane.org>
>
> This patch introduces some miscellaneous header files.
> +static inline void __delay(unsigned long loops)
> +{
> + __asm__ __volatile__(".align 2\n"
> + "1:\n"
> + "\taddi\t%0, %0, -1\n"
> + "\tbgtz\t%0, 1b\n"
> + :"=r"(loops)
> + :"0"(loops));
> +}
> +
> +static inline void __udelay(unsigned long usecs, unsigned long lpj)
> +{
> + usecs *= (unsigned long)(((0x8000000000000000ULL / (500000 / HZ)) +
> + 0x80000000ULL) >> 32);
> + usecs = (unsigned long)(((unsigned long long)usecs * lpj) >> 32);
> + __delay(usecs);
> +}
Do you have a reliable clocksource that you can read here instead of doing the
loop? It's generally preferred to have an accurate delay if at all possible, the
delay loop calibration is only for those architectures that don't have any
way to observe how much time has passed accurately.
Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH 8/8] serdev: ttyport: do not used keyed wakeup in write_wakeup
From: Johan Hovold @ 2017-12-18 11:03 UTC (permalink / raw)
To: Greg Kroah-Hartman
Cc: Johan Hovold, Rob Herring, Jiri Slaby, linux-serial, linux-kernel
In-Reply-To: <20171215192608.GB27395@kroah.com>
On Fri, Dec 15, 2017 at 08:26:08PM +0100, Greg Kroah-Hartman wrote:
> On Wed, Nov 29, 2017 at 10:48:02AM +0100, Johan Hovold wrote:
> > On Tue, Nov 28, 2017 at 08:39:26PM +0100, Greg Kroah-Hartman wrote:
> > > On Tue, Nov 28, 2017 at 04:16:29PM +0100, Johan Hovold wrote:
> > > > On Tue, Nov 28, 2017 at 04:04:18PM +0100, Greg Kroah-Hartman wrote:
> > > > > On Fri, Nov 03, 2017 at 03:30:59PM +0100, Johan Hovold wrote:
> > > > > > Serdev does not use the file abstraction and specifically there will
> > > > > > never be anyone polling a file descriptor for POLLOUT events.
> > > > > >
> > > > > > Just use plain wake_up_interruptible() in the write_wakeup callback and
> > > > > > document why it's there.
> > > > > >
> > > > > > Signed-off-by: Johan Hovold <johan@kernel.org>
> > > > > > ---
> > > > > > drivers/tty/serdev/serdev-ttyport.c | 3 ++-
> > > > > > 1 file changed, 2 insertions(+), 1 deletion(-)
> > > > >
> > > > > This patch didn't apply, perhaps because I split this series across my
> > > > > "for-next" and "for-linus" branches?
> > > >
> > > > That's right, this one depends on patch 4/8.
> > > >
> > > > Perhaps you can take also this one through tty-linus? Or even better,
> > > > just take the whole series through tty-linus?
> > >
> > > They all didn't feel like patches to go in after -rc1, right?
> > > Documentation updates? Minor tweaks? Would you want to defend them?
> > > :)
> >
> > I agree that it's borderline, but the documentation update (patch 3/8)
> > is related to the first two bug fixes, where a negative return value
> > from a serdev driver could have triggered those bugs, so in a sense we
> > are fixing the docs.
> >
> > Patch 6 and 8 are clean ups, but the open lock clean up in patch 6 is
> > related to the close lock fix in patch 5.
> >
> > Patch 7 avoids a potential crash, albeit something that would not affect
> > any mainline drivers (as serial-core sets CLOCAL by default).
> >
> > But I'm perfectly fine with holding them off for 4.16. Perhaps you can
> > just merge back rc2 and I can resubmit the final patch which didn't
> > apply after that.
>
> I've "merged back" now, care to resend the remaining patches?
Just did so. It was just this this single patch that had not yet been
applied.
Thanks,
Johan
^ permalink raw reply
* [PATCH RESEND] serdev: ttyport: do not used keyed wakeup in write_wakeup
From: Johan Hovold @ 2017-12-18 11:00 UTC (permalink / raw)
To: Rob Herring, Greg Kroah-Hartman
Cc: Jiri Slaby, linux-serial, linux-kernel, Johan Hovold
Serdev does not use the file abstraction and specifically there will
never be anyone polling a file descriptor for POLLOUT events.
Just use plain wake_up_interruptible() in the write_wakeup callback and
document why it's there.
Signed-off-by: Johan Hovold <johan@kernel.org>
---
Here's a resend of the final patch from the series "[PATCH 0/8] serdev:
receive_buf and locking fixes", which did not apply after the series was
split over 4.15-rc and -next.
Johan
drivers/tty/serdev/serdev-ttyport.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/serdev/serdev-ttyport.c b/drivers/tty/serdev/serdev-ttyport.c
index c2629ab1bbcf..a5abb05be67d 100644
--- a/drivers/tty/serdev/serdev-ttyport.c
+++ b/drivers/tty/serdev/serdev-ttyport.c
@@ -59,7 +59,8 @@ static void ttyport_write_wakeup(struct tty_port *port)
test_bit(SERPORT_ACTIVE, &serport->flags))
serdev_controller_write_wakeup(ctrl);
- wake_up_interruptible_poll(&tty->write_wait, POLLOUT);
+ /* Wake up any tty_wait_until_sent() */
+ wake_up_interruptible(&tty->write_wait);
tty_kref_put(tty);
}
--
2.15.1
^ permalink raw reply related
* Re: [PATCH v3 07/33] nds32: MMU initialization
From: Guo Ren @ 2017-12-18 9:08 UTC (permalink / raw)
To: Greentime Hu
Cc: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg,
Vincent Chen
In-Reply-To: <0964714c3dcac46ac700085717b0f414b7978112.1512723245.git.green.hu@gmail.com>
Hi Greentime,
On Fri, Dec 08, 2017 at 05:11:50PM +0800, Greentime Hu wrote:
[...]
>
> diff --git a/arch/nds32/mm/highmem.c b/arch/nds32/mm/highmem.c
[...]
> +void *kmap(struct page *page)
> +{
> + unsigned long vaddr;
> + might_sleep();
> + if (!PageHighMem(page))
> + return page_address(page);
> + vaddr = (unsigned long)kmap_high(page);
Here should invalid the cpu_mmu_tlb's entry, Or invalid it in the
set_pte().
eg:
vaddr0 = kmap(page0)
*vaddr0 = val0 //It will cause tlb-miss, and hard-refill to MMU-tlb
kunmap(page0)
vaddr1 = kmap(page1) // Mostly vaddr1 = vaddr0
val = vaddr1; //No tlb-miss and it will get page0's val not page1, because
last expired vaddr0's entry is left in CPU-MMU-tlb.
Best Regards
Guo Ren
^ permalink raw reply
* [PATCH] tty: serial: sh-sci: Add default for number of ports for compile-testing
From: Geert Uytterhoeven @ 2017-12-18 8:50 UTC (permalink / raw)
To: Greg Kroah-Hartman, Jiri Slaby
Cc: kbuild test robot, Stephen Rothwell, linux-serial,
linux-renesas-soc, linux-kernel, Geert Uytterhoeven
When compile-testing an allmodconfig kernel for a platform without
sh-sci serial ports, the SERIAL_SH_SCI_NR_UARTS symbol of type "int"
doesn't get assigned a numerical default value, but an empty string,
leading to a build failure:
.config:3814:warning: symbol value '' invalid for SERIAL_SH_SCI_NR_UARTS
...
make[3]: *** [silentoldconfig] Error 1
Fix this by explicitly providing a default value of 2, like before.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: f6731485a51978ca ("tty: serial: sh-sci: Hide number of ports config question")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
drivers/tty/serial/Kconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 4e6dfb0a762b5807..3682fd3e960cbd64 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -766,6 +766,7 @@ config SERIAL_SH_SCI_NR_UARTS
default "3" if H8300
default "10" if SUPERH
default "18" if ARCH_RENESAS
+ default "2"
config SERIAL_SH_SCI_CONSOLE
bool "Support for console on SuperH SCI(F)" if EXPERT
--
2.7.4
^ permalink raw reply related
* Re: [PATCH 1/2] serial: stm32: add default console
From: Ludovic BARRE @ 2017-12-18 8:31 UTC (permalink / raw)
To: Greg Kroah-Hartman
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-kernel,
Rob Herring, linux-serial, Jiri Slaby, linux-arm-kernel
In-Reply-To: <20171215192517.GA27395@kroah.com>
hi Greg
Yes, the machine could be boot without console. but our
boards has a console by default. it is just to simplified the
configuration.
you can abandoned this patch, if you prefer.
BR
Ludo
On 12/15/2017 08:25 PM, Greg Kroah-Hartman wrote:
> On Fri, Dec 01, 2017 at 05:36:50PM +0100, Ludovic Barre wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch adds by default the console support
>> on stm32.
>
> Why? 'default y' should only mean "machine will not boot without this".
> And I think your machine will boot without the console, right? :)
>
> thanks,
>
> greg k-h
>
^ permalink raw reply
* [PATCH v4 36/36] dt-bindings: timer: Add andestech atcpit100 timer binding doc
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: Rick Chen, green.hu
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Rick Chen <rickchen36@gmail.com>
Add a document to describe Andestech atcpit100 timer and
binding information.
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/timer/andestech,atcpit100-timer.txt | 33 ++++++++++++++++++++
1 file changed, 33 insertions(+)
create mode 100644 Documentation/devicetree/bindings/timer/andestech,atcpit100-timer.txt
diff --git a/Documentation/devicetree/bindings/timer/andestech,atcpit100-timer.txt b/Documentation/devicetree/bindings/timer/andestech,atcpit100-timer.txt
new file mode 100644
index 0000000..4c9ea59
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/andestech,atcpit100-timer.txt
@@ -0,0 +1,33 @@
+Andestech ATCPIT100 timer
+------------------------------------------------------------------
+ATCPIT100 is a generic IP block from Andes Technology, embedded in
+Andestech AE3XX platforms and other designs.
+
+This timer is a set of compact multi-function timers, which can be
+used as pulse width modulators (PWM) as well as simple timers.
+
+It supports up to 4 PIT channels. Each PIT channel is a
+multi-function timer and provide the following usage scenarios:
+One 32-bit timer
+Two 16-bit timers
+Four 8-bit timers
+One 16-bit PWM
+One 16-bit timer and one 8-bit PWM
+Two 8-bit timer and one 8-bit PWM
+
+Required properties:
+- compatible : Should be "andestech,atcpit100"
+- reg : Address and length of the register set
+- interrupts : Reference to the timer interrupt
+- clocks : a clock to provide the tick rate for "andestech,atcpit100"
+- clock-names : should be "PCLK" for the peripheral clock source.
+
+Examples:
+
+timer0: timer@f0400000 {
+ compatible = "andestech,atcpit100";
+ reg = <0xf0400000 0x1000>;
+ interrupts = <2>;
+ clocks = <&apb>;
+ clock-names = "PCLK";
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 35/36] clocksource/drivers/atcpit100: VDSO support
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: Rick Chen, green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Rick Chen <rickchen36@gmail.com>
VDSO needs real-time cycle count to ensure the time accuracy.
Unlike others, nds32 architecture does not define clock source,
hence VDSO needs atcpit100 offering real-time cycle count
to derive the correct time.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
---
drivers/clocksource/timer-atcpit100.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/clocksource/timer-atcpit100.c b/drivers/clocksource/timer-atcpit100.c
index 0077fdb..9b2b628 100644
--- a/drivers/clocksource/timer-atcpit100.c
+++ b/drivers/clocksource/timer-atcpit100.c
@@ -29,6 +29,9 @@
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include "timer-of.h"
+#ifdef CONFIG_NDS32
+#include <asm/vdso_timer_info.h>
+#endif
/*
* Definition of register offsets
@@ -211,6 +214,17 @@ static u64 notrace atcpit100_timer_sched_read(void)
return ~readl(timer_of_base(&to) + CH1_CNT);
}
+#ifdef CONFIG_NDS32
+static void fill_vdso_need_info(struct device_node *node)
+{
+ struct resource timer_res;
+ of_address_to_resource(node, 0, &timer_res);
+ timer_info.mapping_base = (unsigned long)timer_res.start;
+ timer_info.cycle_count_down = true;
+ timer_info.cycle_count_reg_offset = CH1_CNT;
+}
+#endif
+
static int __init atcpit100_timer_init(struct device_node *node)
{
int ret;
@@ -249,6 +263,10 @@ static int __init atcpit100_timer_init(struct device_node *node)
val = readl(base + INT_EN);
writel(val | CH0INT0EN, base + INT_EN);
+#ifdef CONFIG_NDS32
+ fill_vdso_need_info(node);
+#endif
+
return ret;
}
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 34/36] clocksource/drivers/atcpit100: Add andestech atcpit100 timer
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: Rick Chen, green.hu
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Rick Chen <rickchen36@gmail.com>
ATCPIT100 is often used on the Andes architecture,
This timer provide 4 PIT channels. Each PIT channel is a
multi-function timer, can be configured as 32,16,8 bit timers
or PWM as well.
For system timer it will set channel 1 32-bit timer0 as clock
source and count downwards until underflow and restart again.
It also set channel 0 32-bit timer0 as clock event and count
downwards until condition match. It will generate an interrupt
for handling periodically.
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/clocksource/Kconfig | 7 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-atcpit100.c | 255 +++++++++++++++++++++++++++++++++
3 files changed, 263 insertions(+)
create mode 100644 drivers/clocksource/timer-atcpit100.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index cc60620..5bdf92c 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -615,4 +615,11 @@ config CLKSRC_ST_LPC
Enable this option to use the Low Power controller timer
as clocksource.
+config TIMER_ATCPIT100
+ bool "Clocksource for AE3XX platform"
+ depends on NDS32 || COMPILE_TEST
+ depends on HAS_IOMEM
+ help
+ This option enables support for the Andestech AE3XX platform timers.
+
endmenu
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 72711f1..74efe5f 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -75,3 +75,4 @@ obj-$(CONFIG_H8300_TMR16) += h8300_timer16.o
obj-$(CONFIG_H8300_TPU) += h8300_tpu.o
obj-$(CONFIG_CLKSRC_ST_LPC) += clksrc_st_lpc.o
obj-$(CONFIG_X86_NUMACHIP) += numachip.o
+obj-$(CONFIG_TIMER_ATCPIT100) += timer-atcpit100.o
diff --git a/drivers/clocksource/timer-atcpit100.c b/drivers/clocksource/timer-atcpit100.c
new file mode 100644
index 0000000..0077fdb
--- /dev/null
+++ b/drivers/clocksource/timer-atcpit100.c
@@ -0,0 +1,255 @@
+/*
+ * Andestech ATCPIT100 Timer Device Driver Implementation
+ *
+ * Copyright (C) 2017 Andes Technology Corporation
+ * Rick Chen, Andes Technology Corporation <rick@andestech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ *
+ */
+
+#include <linux/irq.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#include <linux/sched.h>
+#include <linux/sched_clock.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include "timer-of.h"
+
+/*
+ * Definition of register offsets
+ */
+
+/* ID and Revision Register */
+#define ID_REV 0x0
+
+/* Configuration Register */
+#define CFG 0x10
+
+/* Interrupt Enable Register */
+#define INT_EN 0x14
+#define CH_INT_EN(c, i) ((1<<i)<<(4*c))
+#define CH0INT0EN 0x01
+
+/* Interrupt Status Register */
+#define INT_STA 0x18
+#define CH0INT0 0x01
+
+/* Channel Enable Register */
+#define CH_EN 0x1C
+#define CH0TMR0EN 0x1
+#define CH1TMR0EN 0x10
+
+/* Channel 0 , 1 Control Register */
+#define CH0_CTL (0x20)
+#define CH1_CTL (0x20 + 0x10)
+
+/* Channel clock source , bit 3 , 0:External clock , 1:APB clock */
+#define APB_CLK BIT(3)
+
+/* Channel mode , bit 0~2 */
+#define TMR_32 0x1
+#define TMR_16 0x2
+#define TMR_8 0x3
+
+/* Channel 0 , 1 Reload Register */
+#define CH0_REL (0x24)
+#define CH1_REL (0x24 + 0x10)
+
+/* Channel 0 , 1 Counter Register */
+#define CH0_CNT (0x28)
+#define CH1_CNT (0x28 + 0x10)
+
+#define TIMER_SYNC_TICKS 3
+
+static void atcpit100_ch1_tmr0_en(void __iomem *base)
+{
+ writel(~0, base + CH1_REL);
+ writel(APB_CLK|TMR_32, base + CH1_CTL);
+}
+
+static void atcpit100_ch0_tmr0_en(void __iomem *base)
+{
+ writel(APB_CLK|TMR_32, base + CH0_CTL);
+}
+
+static void atcpit100_clkevt_time_setup(void __iomem *base, unsigned long delay)
+{
+ writel(delay, base + CH0_CNT);
+ writel(delay, base + CH0_REL);
+}
+
+static void atcpit100_timer_clear_interrupt(void __iomem *base)
+{
+ u32 val;
+
+ val = readl(base + INT_STA);
+ writel(val | CH0INT0, base + INT_STA);
+}
+
+static void atcpit100_clocksource_start(void __iomem *base)
+{
+ u32 val;
+
+ val = readl(base + CH_EN);
+ writel(val | CH1TMR0EN, base + CH_EN);
+}
+
+static void atcpit100_clkevt_time_start(void __iomem *base)
+{
+ u32 val;
+
+ val = readl(base + CH_EN);
+ writel(val | CH0TMR0EN, base + CH_EN);
+}
+
+static void atcpit100_clkevt_time_stop(void __iomem *base)
+{
+ u32 val;
+
+ atcpit100_timer_clear_interrupt(base);
+ val = readl(base + CH_EN);
+ writel(val & ~CH0TMR0EN, base + CH_EN);
+}
+
+static int atcpit100_clkevt_next_event(unsigned long evt,
+ struct clock_event_device *clkevt)
+{
+ struct timer_of *to = to_timer_of(clkevt);
+
+ writel(evt, timer_of_base(to) + CH0_REL);
+
+ return 0;
+}
+
+static int atcpit100_clkevt_set_periodic(struct clock_event_device *evt)
+{
+ struct timer_of *to = to_timer_of(evt);
+
+ atcpit100_clkevt_time_setup(timer_of_base(to), timer_of_period(to));
+ atcpit100_clkevt_time_start(timer_of_base(to));
+
+ return 0;
+}
+static int atcpit100_clkevt_shutdown(struct clock_event_device *evt)
+{
+ struct timer_of *to = to_timer_of(evt);
+
+ atcpit100_clkevt_time_stop(timer_of_base(to));
+
+ return 0;
+}
+static int atcpit100_clkevt_set_oneshot(struct clock_event_device *evt)
+{
+ struct timer_of *to = to_timer_of(evt);
+ u32 val;
+
+ writel(~0x0, timer_of_base(to) + CH0_REL);
+ val = readl(timer_of_base(to) + CH_EN);
+ writel(val | CH0TMR0EN, timer_of_base(to) + CH_EN);
+
+ return 0;
+}
+
+static irqreturn_t atcpit100_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = (struct clock_event_device *)dev_id;
+ struct timer_of *to = to_timer_of(evt);
+
+ atcpit100_timer_clear_interrupt(timer_of_base(to));
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct timer_of to = {
+ .flags = TIMER_OF_IRQ | TIMER_OF_CLOCK | TIMER_OF_BASE,
+
+ .clkevt = {
+ .name = "atcpit100_tick",
+ .rating = 300,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .set_state_shutdown = atcpit100_clkevt_shutdown,
+ .set_state_periodic = atcpit100_clkevt_set_periodic,
+ .set_state_oneshot = atcpit100_clkevt_set_oneshot,
+ .tick_resume = atcpit100_clkevt_shutdown,
+ .set_next_event = atcpit100_clkevt_next_event,
+ .cpumask = cpu_all_mask,
+ },
+
+ .of_irq = {
+ .handler = atcpit100_timer_interrupt,
+ .flags = IRQF_TIMER | IRQF_IRQPOLL,
+ },
+
+ /*
+ * FIXME: we currently only support clocking using PCLK
+ * and using EXTCLK is not supported in the driver.
+ */
+ .of_clk = {
+ .name = "PCLK",
+ }
+};
+
+static u64 notrace atcpit100_timer_sched_read(void)
+{
+ return ~readl(timer_of_base(&to) + CH1_CNT);
+}
+
+static int __init atcpit100_timer_init(struct device_node *node)
+{
+ int ret;
+ u32 val;
+ void __iomem *base;
+
+ ret = timer_of_init(node, &to);
+ if (ret)
+ return ret;
+
+ base = timer_of_base(&to);
+
+ sched_clock_register(atcpit100_timer_sched_read, 32,
+ timer_of_rate(&to));
+
+ ret = clocksource_mmio_init(base + CH1_CNT,
+ node->name, timer_of_rate(&to), 300, 32,
+ clocksource_mmio_readl_down);
+
+ if (ret) {
+ pr_err("Failed to register clocksource\n");
+ return ret;
+ }
+
+ /* clear channel 0 timer0 interrupt */
+ atcpit100_timer_clear_interrupt(base);
+
+ clockevents_config_and_register(&to.clkevt, timer_of_rate(&to),
+ TIMER_SYNC_TICKS, 0xffffffff);
+ atcpit100_ch0_tmr0_en(base);
+ atcpit100_ch1_tmr0_en(base);
+ atcpit100_clocksource_start(base);
+ atcpit100_clkevt_time_start(base);
+
+ /* Enable channel 0 timer0 interrupt */
+ val = readl(base + INT_EN);
+ writel(val | CH0INT0EN, base + INT_EN);
+
+ return ret;
+}
+
+TIMER_OF_DECLARE(atcpit100, "andestech,atcpit100", atcpit100_timer_init);
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 33/36] net: faraday add nds32 support.
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch is used to support nds32 architecture to use these faraday
mac IP.
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
drivers/net/ethernet/faraday/Kconfig | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/faraday/Kconfig b/drivers/net/ethernet/faraday/Kconfig
index 040c7f1..1bdaffc 100644
--- a/drivers/net/ethernet/faraday/Kconfig
+++ b/drivers/net/ethernet/faraday/Kconfig
@@ -5,7 +5,7 @@
config NET_VENDOR_FARADAY
bool "Faraday devices"
default y
- depends on ARM
+ depends on ARM || NDS32 || COMPILE_TEST
---help---
If you have a network (Ethernet) card belonging to this class, say Y.
@@ -18,7 +18,7 @@ if NET_VENDOR_FARADAY
config FTMAC100
tristate "Faraday FTMAC100 10/100 Ethernet support"
- depends on ARM
+ depends on ARM || NDS32 || COMPILE_TEST
select MII
---help---
This driver supports the FTMAC100 10/100 Ethernet controller
@@ -27,7 +27,7 @@ config FTMAC100
config FTGMAC100
tristate "Faraday FTGMAC100 Gigabit Ethernet support"
- depends on ARM
+ depends on ARM || NDS32 || COMPILE_TEST
select PHYLIB
---help---
This driver supports the FTGMAC100 Gigabit Ethernet controller
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 32/36] irqchip: Andestech Internal Vector Interrupt Controller driver
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Rick Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds the Andestech Internal Vector Interrupt Controller
driver. You can find the spec here. Ch4.9 of AndeStar SPA V3 Manual.
http://www.andestech.com/product.php?cls=9
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
---
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-ativic32.c | 107 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 108 insertions(+)
create mode 100644 drivers/irqchip/irq-ativic32.c
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index b842dfd..201ca9f 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -80,3 +80,4 @@ obj-$(CONFIG_ARCH_ASPEED) += irq-aspeed-vic.o irq-aspeed-i2c-ic.o
obj-$(CONFIG_STM32_EXTI) += irq-stm32-exti.o
obj-$(CONFIG_QCOM_IRQ_COMBINER) += qcom-irq-combiner.o
obj-$(CONFIG_IRQ_UNIPHIER_AIDET) += irq-uniphier-aidet.o
+obj-$(CONFIG_NDS32) += irq-ativic32.o
diff --git a/drivers/irqchip/irq-ativic32.c b/drivers/irqchip/irq-ativic32.c
new file mode 100644
index 0000000..f69a858
--- /dev/null
+++ b/drivers/irqchip/irq-ativic32.c
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/irq.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip.h>
+#include <nds32_intrinsic.h>
+
+static void ativic32_ack_irq(struct irq_data *data)
+{
+ __nds32__mtsr_dsb(BIT(data->hwirq), NDS32_SR_INT_PEND2);
+}
+
+static void ativic32_mask_irq(struct irq_data *data)
+{
+ unsigned long int_mask2 = __nds32__mfsr(NDS32_SR_INT_MASK2);
+ __nds32__mtsr_dsb(int_mask2 & (~(BIT(data->hwirq))), NDS32_SR_INT_MASK2);
+}
+
+static void ativic32_unmask_irq(struct irq_data *data)
+{
+ unsigned long int_mask2 = __nds32__mfsr(NDS32_SR_INT_MASK2);
+ __nds32__mtsr_dsb(int_mask2 | (BIT(data->hwirq)), NDS32_SR_INT_MASK2);
+}
+
+static struct irq_chip ativic32_chip = {
+ .name = "ativic32",
+ .irq_ack = ativic32_ack_irq,
+ .irq_mask = ativic32_mask_irq,
+ .irq_unmask = ativic32_unmask_irq,
+};
+
+static unsigned int __initdata nivic_map[6] = { 6, 2, 10, 16, 24, 32 };
+
+static struct irq_domain *root_domain;
+static int ativic32_irq_domain_map(struct irq_domain *id, unsigned int virq,
+ irq_hw_number_t hw)
+{
+
+ unsigned long int_trigger_type;
+ u32 type;
+ struct irq_data *irq_data;
+ int_trigger_type = __nds32__mfsr(NDS32_SR_INT_TRIGGER);
+ irq_data = irq_get_irq_data(virq);
+ if (!irq_data)
+ return -EINVAL;
+
+ if (int_trigger_type & (BIT(hw))) {
+ irq_set_chip_and_handler(virq, &ativic32_chip, handle_edge_irq);
+ type = IRQ_TYPE_EDGE_RISING;
+ } else {
+ irq_set_chip_and_handler(virq, &ativic32_chip, handle_level_irq);
+ type = IRQ_TYPE_LEVEL_HIGH;
+ }
+
+ irqd_set_trigger_type(irq_data, type);
+ return 0;
+}
+
+static struct irq_domain_ops ativic32_ops = {
+ .map = ativic32_irq_domain_map,
+ .xlate = irq_domain_xlate_onecell
+};
+
+static irq_hw_number_t get_intr_src(void)
+{
+ return ((__nds32__mfsr(NDS32_SR_ITYPE) & ITYPE_mskVECTOR) >> ITYPE_offVECTOR)
+ - NDS32_VECTOR_offINTERRUPT;
+}
+
+asmlinkage void asm_do_IRQ(struct pt_regs *regs)
+{
+ irq_hw_number_t hwirq = get_intr_src();
+ handle_domain_irq(root_domain, hwirq, regs);
+}
+
+int __init ativic32_init_irq(struct device_node *node, struct device_node *parent)
+{
+ unsigned long int_vec_base, nivic, nr_ints;
+
+ if (WARN(parent, "non-root ativic32 are not supported"))
+ return -EINVAL;
+
+ int_vec_base = __nds32__mfsr(NDS32_SR_IVB);
+
+ if (((int_vec_base & IVB_mskIVIC_VER) >> IVB_offIVIC_VER) == 0)
+ panic("Unable to use atcivic32 for this cpu.\n");
+
+ nivic = (int_vec_base & IVB_mskNIVIC) >> IVB_offNIVIC;
+ if (nivic >= ARRAY_SIZE(nivic_map))
+ panic("The number of input for ativic32 is not supported.\n");
+
+ nr_ints = nivic_map[nivic];
+
+ root_domain = irq_domain_add_linear(node, nr_ints,
+ &ativic32_ops, NULL);
+
+ if (!root_domain)
+ panic("%s: unable to create IRQ domain\n", node->full_name);
+
+ return 0;
+}
+IRQCHIP_DECLARE(ativic32, "andestech,ativic32", ativic32_init_irq);
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 31/36] dt-bindings: interrupt-controller: Andestech Internal Vector Interrupt Controller
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Rick Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds an irqchip driver document for the Andestech Internal Vector
Interrupt Controller.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../interrupt-controller/andestech,ativic32.txt | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interrupt-controller/andestech,ativic32.txt
diff --git a/Documentation/devicetree/bindings/interrupt-controller/andestech,ativic32.txt b/Documentation/devicetree/bindings/interrupt-controller/andestech,ativic32.txt
new file mode 100644
index 0000000..f4b4193
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/andestech,ativic32.txt
@@ -0,0 +1,19 @@
+* Andestech Internal Vector Interrupt Controller
+
+The Internal Vector Interrupt Controller (IVIC) is a basic interrupt controller
+suitable for a simpler SoC platform not requiring a more sophisticated and
+bigger External Vector Interrupt Controller.
+
+
+Main node required properties:
+
+- compatible : should at least contain "andestech,ativic32".
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells: 1 cells and refer to interrupt-controller/interrupts
+
+Examples:
+ intc: interrupt-controller {
+ compatible = "andestech,ativic32";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 30/36] dt-bindings: nds32 SoC Bindings
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds nds32 SoC(AE3XX and AG101P) binding documents.
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/nds32/andestech-boards | 40 ++++++++++++++++++++
1 file changed, 40 insertions(+)
create mode 100644 Documentation/devicetree/bindings/nds32/andestech-boards
diff --git a/Documentation/devicetree/bindings/nds32/andestech-boards b/Documentation/devicetree/bindings/nds32/andestech-boards
new file mode 100644
index 0000000..f5d7569
--- /dev/null
+++ b/Documentation/devicetree/bindings/nds32/andestech-boards
@@ -0,0 +1,40 @@
+Andestech(nds32) AE3XX Platform
+-----------------------------------------------------------------------------
+The AE3XX prototype demonstrates the AE3XX example platform on the FPGA. It
+is composed of one Andestech(nds32) processor and AE3XX.
+
+Required properties (in root node):
+- compatible = "andestech,ae3xx";
+
+Example:
+/dts-v1/;
+/ {
+ compatible = "andestech,ae3xx";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+};
+
+Andestech(nds32) AG101P Platform
+-----------------------------------------------------------------------------
+AG101P is a generic SoC Platform IP that works with any of Andestech(nds32)
+processors to provide a cost-effective and high performance solution for
+majority of embedded systems in variety of application domains. Users may
+simply attach their IP on one of the system buses together with certain glue
+logics to complete a SoC solution for a specific application. With
+comprehensive simulation and design environments, users may evaluate the
+system performance of their applications and track bugs of their designs
+efficiently. The optional hardware development platform further provides real
+system environment for early prototyping and software/hardware co-development.
+
+Required properties (in root node):
+ compatible = "andestech,ag101p";
+
+Example:
+/dts-v1/;
+/ {
+ compatible = "andestech,ag101p";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 29/36] dt-bindings: nds32 CPU Bindings
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen, Rick Chen, Zong Li
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds nds32 CPU binding documents.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Zong Li <zong@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/nds32/cpus.txt | 37 ++++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/nds32/cpus.txt
diff --git a/Documentation/devicetree/bindings/nds32/cpus.txt b/Documentation/devicetree/bindings/nds32/cpus.txt
new file mode 100644
index 0000000..9a52937
--- /dev/null
+++ b/Documentation/devicetree/bindings/nds32/cpus.txt
@@ -0,0 +1,37 @@
+* Andestech Processor Binding
+
+This binding specifies what properties must be available in the device tree
+representation of a Andestech Processor Core, which is the root node in the
+tree.
+
+Required properties:
+
+ - compatible:
+ Usage: required
+ Value type: <string>
+ Definition: should be one of:
+ "andestech,n13"
+ "andestech,n15"
+ "andestech,d15"
+ "andestech,n10"
+ "andestech,d10"
+ "andestech,nds32v3"
+ - device_type
+ Usage: required
+ Value type: <string>
+ Definition: must be "cpu"
+ - reg: Contains CPU index.
+ - clock-frequency: Contains the clock frequency for CPU, in Hz.
+
+* Examples
+
+/ {
+ cpus {
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "andestech,n13", "andestech,nds32v3";
+ reg = <0x0>;
+ clock-frequency = <60000000>
+ };
+ };
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 28/36] MAINTAINERS: Add nds32
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
MAINTAINERS | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 2f4e462..20284c8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -857,6 +857,17 @@ X: drivers/iio/*/adjd*
F: drivers/staging/iio/*/ad*
F: drivers/staging/iio/trigger/iio-trig-bfin-timer.c
+ANDES ARCHITECTURE
+M: Greentime Hu <green.hu@gmail.com>
+M: Vincent Chen <deanbo422@gmail.com>
+T: git https://github.com/andestech/linux.git
+S: Supported
+F: arch/nds32
+F: Documentation/devicetree/bindings/interrupt-controller/andestech,ativic32.txt
+F: Documentation/devicetree/bindings/nds32
+K: nds32
+N: nds32
+
ANDROID CONFIG FRAGMENTS
M: Rob Herring <robh@kernel.org>
S: Supported
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 27/36] nds32: Build infrastructure
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds Makefile, Kconfig and vmlinux.lds.S files required for building
an nds32 kernel.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/Kconfig | 108 ++++++++++++++++++++++++
arch/nds32/Kconfig.cpu | 161 ++++++++++++++++++++++++++++++++++++
arch/nds32/Makefile | 66 +++++++++++++++
arch/nds32/boot/Makefile | 15 ++++
arch/nds32/include/asm/Kbuild | 53 ++++++++++++
arch/nds32/include/uapi/asm/Kbuild | 28 +++++++
arch/nds32/kernel/Makefile | 23 ++++++
arch/nds32/kernel/vmlinux.lds.S | 57 +++++++++++++
arch/nds32/mm/Makefile | 7 ++
9 files changed, 518 insertions(+)
create mode 100644 arch/nds32/Kconfig
create mode 100644 arch/nds32/Kconfig.cpu
create mode 100644 arch/nds32/Makefile
create mode 100644 arch/nds32/boot/Makefile
create mode 100644 arch/nds32/include/asm/Kbuild
create mode 100644 arch/nds32/include/uapi/asm/Kbuild
create mode 100644 arch/nds32/kernel/Makefile
create mode 100644 arch/nds32/kernel/vmlinux.lds.S
create mode 100644 arch/nds32/mm/Makefile
diff --git a/arch/nds32/Kconfig b/arch/nds32/Kconfig
new file mode 100644
index 0000000..c83506e
--- /dev/null
+++ b/arch/nds32/Kconfig
@@ -0,0 +1,108 @@
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.txt.
+#
+
+config NDS32
+ def_bool y
+ select ARCH_HAS_RAW_COPY_USER
+ select ARCH_WANT_FRAME_POINTERS if FTRACE
+ select ARCH_WANT_IPC_PARSE_VERSION
+ select CLKSRC_MMIO
+ select CLONE_BACKWARDS
+ select COMMON_CLK
+ select TIMER_OF
+ select FRAME_POINTER
+ select GENERIC_ATOMIC64
+ select GENERIC_CPU_DEVICES
+ select GENERIC_CLOCKEVENTS
+ select GENERIC_IRQ_CHIP
+ select GENERIC_IRQ_PROBE
+ select GENERIC_IRQ_SHOW
+ select GENERIC_STRNCPY_FROM_USER
+ select GENERIC_STRNLEN_USER
+ select GENERIC_TIME_VSYSCALL
+ select HANDLE_DOMAIN_IRQ
+ select HAVE_ARCH_TRACEHOOK
+ select HAVE_DEBUG_KMEMLEAK
+ select HAVE_MEMBLOCK
+ select HAVE_REGS_AND_STACK_ACCESS_API
+ select IRQ_DOMAIN
+ select LOCKDEP_SUPPORT
+ select MODULES_USE_ELF_RELA
+ select OF
+ select OF_EARLY_FLATTREE
+ select NO_BOOTMEM
+ select NO_IOPORT_MAP
+ select RTC_LIB
+ select THREAD_INFO_IN_TASK
+ help
+ Andes(nds32) Linux support.
+
+config GENERIC_CALIBRATE_DELAY
+ def_bool n
+
+config GENERIC_CSUM
+ def_bool y
+
+config GENERIC_HWEIGHT
+ def_bool y
+
+config GENERIC_LOCKBREAK
+ def_bool y
+ depends on PREEMPT
+
+config RWSEM_GENERIC_SPINLOCK
+ def_bool y
+
+config TRACE_IRQFLAGS_SUPPORT
+ def_bool y
+
+config STACKTRACE_SUPPORT
+ def_bool y
+
+config FIX_EARLYCON_MEM
+ def_bool y
+
+config PGTABLE_LEVELS
+ default 2
+
+source "init/Kconfig"
+
+menu "System Type"
+source "arch/nds32/Kconfig.cpu"
+config NR_CPUS
+ int
+ default 1
+
+config MMU
+ def_bool y
+
+config NDS32_BUILTIN_DTB
+ string "Builtin DTB"
+ default ""
+ help
+ User can use it to specify the dts of the SoC
+endmenu
+
+menu "Kernel Features"
+source "kernel/Kconfig.preempt"
+source "mm/Kconfig"
+source "kernel/Kconfig.hz"
+endmenu
+
+menu "Executable file formats"
+source "fs/Kconfig.binfmt"
+endmenu
+
+source "net/Kconfig"
+source "drivers/Kconfig"
+source "fs/Kconfig"
+
+menu "Kernel hacking"
+source "lib/Kconfig.debug"
+endmenu
+
+source "security/Kconfig"
+source "crypto/Kconfig"
+source "lib/Kconfig"
diff --git a/arch/nds32/Kconfig.cpu b/arch/nds32/Kconfig.cpu
new file mode 100644
index 0000000..6c9fbdc
--- /dev/null
+++ b/arch/nds32/Kconfig.cpu
@@ -0,0 +1,161 @@
+comment "Processor Features"
+
+config CPU_BIG_ENDIAN
+ bool "Big endian"
+
+config CPU_LITTLE_ENDIAN
+ def_bool !CPU_BIG_ENDIAN
+
+config HWZOL
+ bool "hardware zero overhead loop support"
+ depends on CPU_D10 || CPU_D15
+ default n
+ help
+ A set of Zero-Overhead Loop mechanism is provided to reduce the
+ instruction fetch and execution overhead of loop-control instructions.
+ It will save 3 registers($LB, $LC, $LE) for context saving if say Y.
+ You don't need to save these registers if you can make sure your user
+ program doesn't use these registers.
+
+ If unsure, say N.
+
+config CPU_CACHE_ALIASING
+ bool "Aliasing cache"
+ depends on CPU_N10 || CPU_D10 || CPU_N13 || CPU_V3
+ default y
+ help
+ If this CPU is using VIPT data cache and its cache way size is larger
+ than page size, say Y. If it is using PIPT data cache, say N.
+
+ If unsure, say Y.
+
+choice
+ prompt "CPU type"
+ default CPU_V3
+config CPU_N15
+ bool "AndesCore N15"
+config CPU_N13
+ bool "AndesCore N13"
+ select CPU_CACHE_ALIASING if ANDES_PAGE_SIZE_4KB
+config CPU_N10
+ bool "AndesCore N10"
+ select CPU_CACHE_ALIASING
+config CPU_D15
+ bool "AndesCore D15"
+config CPU_D10
+ bool "AndesCore D10"
+ select CPU_CACHE_ALIASING
+config CPU_V3
+ bool "AndesCore v3 compatible"
+ select ANDES_PAGE_SIZE_8KB
+endchoice
+choice
+ prompt "Paging -- page size "
+ default ANDES_PAGE_SIZE_4KB
+config ANDES_PAGE_SIZE_4KB
+ bool "use 4KB page size"
+config ANDES_PAGE_SIZE_8KB
+ bool "use 8KB page size"
+endchoice
+
+config CPU_ICACHE_DISABLE
+ bool "Disable I-Cache"
+ help
+ Say Y here to disable the processor instruction cache. Unless
+ you have a reason not to or are unsure, say N.
+
+config CPU_DCACHE_DISABLE
+ bool "Disable D-Cache"
+ help
+ Say Y here to disable the processor data cache. Unless
+ you have a reason not to or are unsure, say N.
+
+config CPU_DCACHE_WRITETHROUGH
+ bool "Force write through D-cache"
+ depends on !CPU_DCACHE_DISABLE
+ help
+ Say Y here to use the data cache in writethrough mode. Unless you
+ specifically require this or are unsure, say N.
+
+config WBNA
+ bool "WBNA"
+ default n
+ help
+ Say Y here to enable write-back memory with no-write-allocation policy.
+
+config ALIGNMENT_TRAP
+ bool "Kernel support unaligned access handling by sw"
+ depends on PROC_FS
+ default n
+ help
+ Andes processors cannot fetch/store information which is not
+ naturally aligned on the bus, i.e., a 4 byte fetch must start at an
+ address divisible by 4. On 32-bit Andes processors, these non-aligned
+ fetch/store instructions will be emulated in software if you say
+ here, which has a severe performance impact. With an IP-only
+ configuration it is safe to say N, otherwise say Y.
+
+config HW_SUPPORT_UNALIGNMENT_ACCESS
+ bool "Kernel support unaligned access handling by hw"
+ depends on !ALIGNMENT_TRAP
+ default n
+ help
+ Andes processors load/store world/half-word instructions can access
+ unaligned memory locations without generating the Data Alignment
+ Check exceptions. With an IP-only configuration it is safe to say N,
+ otherwise say Y.
+
+config HIGHMEM
+ bool "High Memory Support"
+ depends on MMU && CPU_CACHE_NONALIASING
+ help
+ The address space of Andes processors is only 4 Gigabytes large
+ and it has to accommodate user address space, kernel address
+ space as well as some memory mapped IO. That means that, if you
+ have a large amount of physical memory and/or IO, not all of the
+ memory can be "permanently mapped" by the kernel. The physical
+ memory that is not permanently mapped is called "high memory".
+
+ Depending on the selected kernel/user memory split, minimum
+ vmalloc space and actual amount of RAM, you may not need this
+ option which should result in a slightly faster kernel.
+
+ If unsure, say N.
+
+config CACHE_L2
+ bool "Support L2 cache"
+ default y
+ help
+ Say Y here to enable L2 cache if your SoC are integrated with L2CC.
+ If unsure, say N.
+
+menu "Memory configuration"
+
+choice
+ prompt "Memory split"
+ depends on MMU
+ default VMSPLIT_3G
+ help
+ Select the desired split between kernel and user memory.
+
+ If you are not absolutely sure what you are doing, leave this
+ option alone!
+
+ config VMSPLIT_3G
+ bool "3G/1G user/kernel split"
+ config VMSPLIT_3G_OPT
+ bool "3G/1G user/kernel split (for full 1G low memory)"
+ config VMSPLIT_2G
+ bool "2G/2G user/kernel split"
+ config VMSPLIT_1G
+ bool "1G/3G user/kernel split"
+endchoice
+
+config PAGE_OFFSET
+ hex
+ default 0x40000000 if VMSPLIT_1G
+ default 0x80000000 if VMSPLIT_2G
+ default 0xB0000000 if VMSPLIT_3G_OPT
+ default 0xC0000000
+
+endmenu
diff --git a/arch/nds32/Makefile b/arch/nds32/Makefile
new file mode 100644
index 0000000..54b4de9
--- /dev/null
+++ b/arch/nds32/Makefile
@@ -0,0 +1,66 @@
+LDFLAGS_vmlinux := --no-undefined -X
+OBJCOPYFLAGS := -O binary -R .note -R .note.gnu.build-id -R .comment -S
+
+KBUILD_DEFCONFIG := defconfig
+
+comma = ,
+
+KBUILD_CFLAGS +=-mno-sched-prolog-epilog -mcmodel=large
+
+KBUILD_CFLAGS +=$(arch-y) $(tune-y)
+KBUILD_AFLAGS +=$(arch-y) $(tune-y)
+
+#Default value
+head-y := arch/nds32/kernel/head.o
+textaddr-y := $(CONFIG_PAGE_OFFSET)+0xc000
+
+TEXTADDR := $(textaddr-y)
+
+export TEXTADDR
+
+
+# If we have a machine-specific directory, then include it in the build.
+core-y += arch/nds32/kernel/ arch/nds32/mm/
+libs-y += arch/nds32/lib/
+LIBGCC_PATH := \
+ $(shell $(CC) $(KBUILD_CFLAGS) $(KCFLAGS) -print-libgcc-file-name)
+libs-y += $(LIBGCC_PATH)
+
+ifneq '$(CONFIG_NDS32_BUILTIN_DTB)' '""'
+BUILTIN_DTB := y
+else
+BUILTIN_DTB := n
+endif
+
+ifdef CONFIG_CPU_LITTLE_ENDIAN
+KBUILD_CFLAGS += -EL
+else
+KBUILD_CFLAGS += -EB
+endif
+
+boot := arch/nds32/boot
+core-$(BUILTIN_DTB) += $(boot)/dts/
+
+.PHONY: FORCE
+
+Image: vmlinux
+ $(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
+
+
+PHONY += vdso_install
+vdso_install:
+ $(Q)$(MAKE) $(build)=arch/nds32/kernel/vdso $@
+
+prepare: vdso_prepare
+vdso_prepare: prepare0
+ $(Q)$(MAKE) $(build)=arch/nds32/kernel/vdso include/generated/vdso-offsets.h
+
+CLEAN_FILES += include/asm-nds32/constants.h*
+
+# We use MRPROPER_FILES and CLEAN_FILES now
+archclean:
+ $(Q)$(MAKE) $(clean)=$(boot)
+
+define archhelp
+ echo ' Image - kernel image (arch/$(ARCH)/boot/Image)'
+endef
diff --git a/arch/nds32/boot/Makefile b/arch/nds32/boot/Makefile
new file mode 100644
index 0000000..3f9b86f
--- /dev/null
+++ b/arch/nds32/boot/Makefile
@@ -0,0 +1,15 @@
+targets := Image Image.gz
+
+$(obj)/Image: vmlinux FORCE
+ $(call if_changed,objcopy)
+
+$(obj)/Image.gz: $(obj)/Image FORCE
+ $(call if_changed,gzip)
+
+install: $(obj)/Image
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+ $(obj)/Image System.map "$(INSTALL_PATH)"
+
+zinstall: $(obj)/Image.gz
+ $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \
+ $(obj)/Image.gz System.map "$(INSTALL_PATH)"
diff --git a/arch/nds32/include/asm/Kbuild b/arch/nds32/include/asm/Kbuild
new file mode 100644
index 0000000..8046ca5
--- /dev/null
+++ b/arch/nds32/include/asm/Kbuild
@@ -0,0 +1,53 @@
+generic-y += asm-offsets.h
+generic-y += atomic.h
+generic-y += bitops.h
+generic-y += bitsperlong.h
+generic-y += bug.h
+generic-y += bugs.h
+generic-y += checksum.h
+generic-y += clkdev.h
+generic-y += cmpxchg.h
+generic-y += cmpxchg-local.h
+generic-y += cputime.h
+generic-y += device.h
+generic-y += div64.h
+generic-y += dma.h
+generic-y += emergency-restart.h
+generic-y += errno.h
+generic-y += exec.h
+generic-y += fb.h
+generic-y += fcntl.h
+generic-y += ftrace.h
+generic-y += gpio.h
+generic-y += hardirq.h
+generic-y += hw_irq.h
+generic-y += ioctl.h
+generic-y += ioctls.h
+generic-y += irq.h
+generic-y += irq_regs.h
+generic-y += irq_work.h
+generic-y += kdebug.h
+generic-y += kmap_types.h
+generic-y += kprobes.h
+generic-y += kvm_para.h
+generic-y += limits.h
+generic-y += local.h
+generic-y += mm-arch-hooks.h
+generic-y += mman.h
+generic-y += parport.h
+generic-y += pci.h
+generic-y += percpu.h
+generic-y += preempt.h
+generic-y += sections.h
+generic-y += segment.h
+generic-y += serial.h
+generic-y += shmbuf.h
+generic-y += sizes.h
+generic-y += stat.h
+generic-y += switch_to.h
+generic-y += timex.h
+generic-y += topology.h
+generic-y += trace_clock.h
+generic-y += unaligned.h
+generic-y += user.h
+generic-y += word-at-a-time.h
diff --git a/arch/nds32/include/uapi/asm/Kbuild b/arch/nds32/include/uapi/asm/Kbuild
new file mode 100644
index 0000000..c4dc909
--- /dev/null
+++ b/arch/nds32/include/uapi/asm/Kbuild
@@ -0,0 +1,28 @@
+# UAPI Header export list
+include include/uapi/asm-generic/Kbuild.asm
+
+generic-y += errno.h
+generic-y += ioctl.h
+generic-y += ioctls.h
+generic-y += ipcbuf.h
+generic-y += shmbuf.h
+generic-y += bitsperlong.h
+generic-y += fcntl.h
+generic-y += stat.h
+generic-y += mman.h
+generic-y += msgbuf.h
+generic-y += poll.h
+generic-y += posix_types.h
+generic-y += resource.h
+generic-y += sembuf.h
+generic-y += setup.h
+generic-y += siginfo.h
+generic-y += signal.h
+generic-y += socket.h
+generic-y += sockios.h
+generic-y += swab.h
+generic-y += statfs.h
+generic-y += termbits.h
+generic-y += termios.h
+generic-y += types.h
+generic-y += ucontext.h
diff --git a/arch/nds32/kernel/Makefile b/arch/nds32/kernel/Makefile
new file mode 100644
index 0000000..4279274
--- /dev/null
+++ b/arch/nds32/kernel/Makefile
@@ -0,0 +1,23 @@
+#
+# Makefile for the linux kernel.
+#
+
+CPPFLAGS_vmlinux.lds := -DTEXTADDR=$(TEXTADDR)
+AFLAGS_head.o := -DTEXTADDR=$(TEXTADDR)
+
+# Object file lists.
+
+obj-y := ex-entry.o ex-exit.o ex-scall.o irq.o \
+ process.o ptrace.o setup.o signal.o \
+ sys_nds32.o time.o traps.o cacheinfo.o \
+ dma.o syscall_table.o vdso.o
+
+obj-$(CONFIG_MODULES) += nds32_ksyms.o module.o
+obj-$(CONFIG_STACKTRACE) += stacktrace.o
+obj-$(CONFIG_OF) += devtree.o
+obj-$(CONFIG_CACHE_L2) += atl2c.o
+
+extra-y := head.o vmlinux.lds
+
+
+obj-y += vdso/
diff --git a/arch/nds32/kernel/vmlinux.lds.S b/arch/nds32/kernel/vmlinux.lds.S
new file mode 100644
index 0000000..288313b
--- /dev/null
+++ b/arch/nds32/kernel/vmlinux.lds.S
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <asm/page.h>
+#include <asm/thread_info.h>
+#include <asm/cache.h>
+#include <asm/memory.h>
+
+#define LOAD_OFFSET (PAGE_OFFSET - PHYS_OFFSET)
+#include <asm-generic/vmlinux.lds.h>
+
+OUTPUT_ARCH(nds32)
+ENTRY(_stext_lma)
+jiffies = jiffies_64;
+
+SECTIONS
+{
+ _stext_lma = TEXTADDR - LOAD_OFFSET;
+ . = TEXTADDR;
+ __init_begin = .;
+ HEAD_TEXT_SECTION
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ INIT_DATA_SECTION(16)
+ PERCPU_SECTION(L1_CACHE_BYTES)
+ __init_end = .;
+
+ . = ALIGN(PAGE_SIZE);
+ _stext = .;
+ /* Real text segment */
+ .text : AT(ADDR(.text) - LOAD_OFFSET) {
+ _text = .; /* Text and read-only data */
+ TEXT_TEXT
+ SCHED_TEXT
+ CPUIDLE_TEXT
+ LOCK_TEXT
+ KPROBES_TEXT
+ IRQENTRY_TEXT
+ *(.fixup)
+ }
+
+ _etext = .; /* End of text and rodata section */
+
+ _sdata = .;
+ RO_DATA_SECTION(PAGE_SIZE)
+ RW_DATA_SECTION(L1_CACHE_BYTES, PAGE_SIZE, THREAD_SIZE)
+ _edata = .;
+
+ EXCEPTION_TABLE(16)
+ NOTES
+ BSS_SECTION(4, 4, 4)
+ _end = .;
+
+ STABS_DEBUG
+ DWARF_DEBUG
+
+ DISCARDS
+}
diff --git a/arch/nds32/mm/Makefile b/arch/nds32/mm/Makefile
new file mode 100644
index 0000000..6b68558
--- /dev/null
+++ b/arch/nds32/mm/Makefile
@@ -0,0 +1,7 @@
+obj-y := extable.o tlb.o \
+ fault.o init.o ioremap.o mmap.o \
+ mm-nds32.o cacheflush.o proc.o
+
+obj-$(CONFIG_ALIGNMENT_TRAP) += alignment.o
+obj-$(CONFIG_HIGHMEM) += highmem.o
+CFLAGS_proc-n13.o += -fomit-frame-pointer
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 26/36] nds32: defconfig
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds nds32 defconfig.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/configs/defconfig | 108 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 108 insertions(+)
create mode 100644 arch/nds32/configs/defconfig
diff --git a/arch/nds32/configs/defconfig b/arch/nds32/configs/defconfig
new file mode 100644
index 0000000..4d79d2db
--- /dev/null
+++ b/arch/nds32/configs/defconfig
@@ -0,0 +1,108 @@
+CONFIG_CROSS_COMPILE="nds32le-linux-"
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_USER_NS=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_PROFILING=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CACHE_L2 is not set
+CONFIG_VMSPLIT_3G_OPT=y
+CONFIG_PREEMPT=y
+# CONFIG_COMPACTION is not set
+CONFIG_HZ_100=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_BLK_DEV is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_FTMAC100=y
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_RC_CORE is not set
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID_A4TECH is not set
+# CONFIG_HID_APPLE is not set
+# CONFIG_HID_BELKIN is not set
+# CONFIG_HID_CHERRY is not set
+# CONFIG_HID_CHICONY is not set
+# CONFIG_HID_CYPRESS is not set
+# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_ITE is not set
+# CONFIG_HID_KENSINGTON is not set
+# CONFIG_HID_LOGITECH is not set
+# CONFIG_HID_MICROSOFT is not set
+# CONFIG_HID_MONTEREY is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_TIMER_ATCPIT100=y
+CONFIG_GENERIC_PHY=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_EXT4_ENCRYPTION=y
+CONFIG_FUSE_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_USE_LEGACY_DNS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF4=y
+CONFIG_GDB_SCRIPTS=y
+CONFIG_READABLE_ASM=y
+CONFIG_HEADERS_CHECK=y
+CONFIG_DEBUG_SECTION_MISMATCH=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_PANIC_ON_OOPS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+CONFIG_RCU_CPU_STALL_TIMEOUT=300
+# CONFIG_CRYPTO_HW is not set
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 25/36] nds32: Miscellaneous header files
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch introduces some miscellaneous header files.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/include/asm/delay.h | 38 +++++++++++++++++++++++++++++++
arch/nds32/include/asm/linkage.h | 11 +++++++++
arch/nds32/include/uapi/asm/byteorder.h | 13 +++++++++++
3 files changed, 62 insertions(+)
create mode 100644 arch/nds32/include/asm/delay.h
create mode 100644 arch/nds32/include/asm/linkage.h
create mode 100644 arch/nds32/include/uapi/asm/byteorder.h
diff --git a/arch/nds32/include/asm/delay.h b/arch/nds32/include/asm/delay.h
new file mode 100644
index 0000000..1852a4e
--- /dev/null
+++ b/arch/nds32/include/asm/delay.h
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef __NDS32_DELAY_H__
+#define __NDS32_DELAY_H__
+
+#include <asm/param.h>
+
+static inline void __delay(unsigned long loops)
+{
+ __asm__ __volatile__(".align 2\n"
+ "1:\n"
+ "\taddi\t%0, %0, -1\n"
+ "\tbgtz\t%0, 1b\n"
+ :"=r"(loops)
+ :"0"(loops));
+}
+
+static inline void __udelay(unsigned long usecs, unsigned long lpj)
+{
+ usecs *= (unsigned long)(((0x8000000000000000ULL / (500000 / HZ)) +
+ 0x80000000ULL) >> 32);
+ usecs = (unsigned long)(((unsigned long long)usecs * lpj) >> 32);
+ __delay(usecs);
+}
+
+#define udelay(usecs) __udelay((usecs), loops_per_jiffy)
+
+/* make sure "usecs *= ..." in udelay do not overflow. */
+#if HZ >= 1000
+#define MAX_UDELAY_MS 1
+#elif HZ <= 200
+#define MAX_UDELAY_MS 5
+#else
+#define MAX_UDELAY_MS (1000 / HZ)
+#endif
+
+#endif
diff --git a/arch/nds32/include/asm/linkage.h b/arch/nds32/include/asm/linkage.h
new file mode 100644
index 0000000..e708c8b
--- /dev/null
+++ b/arch/nds32/include/asm/linkage.h
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef __ASM_LINKAGE_H
+#define __ASM_LINKAGE_H
+
+/* This file is required by include/linux/linkage.h */
+#define __ALIGN .align 2
+#define __ALIGN_STR ".align 2"
+
+#endif
diff --git a/arch/nds32/include/uapi/asm/byteorder.h b/arch/nds32/include/uapi/asm/byteorder.h
new file mode 100644
index 0000000..a23f6f3a
--- /dev/null
+++ b/arch/nds32/include/uapi/asm/byteorder.h
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef __NDS32_BYTEORDER_H__
+#define __NDS32_BYTEORDER_H__
+
+#ifdef __NDS32_EB__
+#include <linux/byteorder/big_endian.h>
+#else
+#include <linux/byteorder/little_endian.h>
+#endif
+
+#endif /* __NDS32_BYTEORDER_H__ */
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 24/36] nds32: Device tree support
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds support for device tree.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/boot/dts/Makefile | 8 +++++
arch/nds32/boot/dts/ae3xx.dts | 65 +++++++++++++++++++++++++++++++++++++++++
arch/nds32/kernel/devtree.c | 19 ++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 arch/nds32/boot/dts/Makefile
create mode 100644 arch/nds32/boot/dts/ae3xx.dts
create mode 100644 arch/nds32/kernel/devtree.c
diff --git a/arch/nds32/boot/dts/Makefile b/arch/nds32/boot/dts/Makefile
new file mode 100644
index 0000000..d31faa8
--- /dev/null
+++ b/arch/nds32/boot/dts/Makefile
@@ -0,0 +1,8 @@
+ifneq '$(CONFIG_NDS32_BUILTIN_DTB)' '""'
+BUILTIN_DTB := $(patsubst "%",%,$(CONFIG_NDS32_BUILTIN_DTB)).dtb.o
+else
+BUILTIN_DTB :=
+endif
+obj-$(CONFIG_OF) += $(BUILTIN_DTB)
+
+clean-files := *.dtb *.dtb.S
diff --git a/arch/nds32/boot/dts/ae3xx.dts b/arch/nds32/boot/dts/ae3xx.dts
new file mode 100644
index 0000000..0ef2c44
--- /dev/null
+++ b/arch/nds32/boot/dts/ae3xx.dts
@@ -0,0 +1,65 @@
+/dts-v1/;
+/ {
+ compatible = "andestech,ae3xx";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+
+ chosen {
+ stdout-path = &serial0;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "andestech,n13", "andestech,nds32v3";
+ reg = <0>;
+ clock-frequency = <60000000>;
+ };
+ };
+
+ apb: clk@0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <30000000>;
+ };
+
+
+ intc: interrupt-controller {
+ compatible = "andestech,ativic32";
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ };
+
+ serial0: serial@f0300000 {
+ compatible = "andestech,uart16550", "ns16550a";
+ reg = <0xf0300000 0x1000>;
+ interrupts = <8>;
+ clock-frequency = <14745600>;
+ reg-shift = <2>;
+ reg-offset = <32>;
+ no-loopback-test = <1>;
+ };
+
+ timer0: timer@f0400000 {
+ compatible = "andestech,atcpit100";
+ reg = <0xf0400000 0x1000>;
+ interrupts = <2>;
+ clocks = <&apb>;
+ clock-names = "PCLK";
+ };
+
+ mac0: mac@e0100000 {
+ compatible = "andestech,atmac100";
+ reg = <0xe0100000 0x1000>;
+ interrupts = <18>;
+ };
+
+};
diff --git a/arch/nds32/kernel/devtree.c b/arch/nds32/kernel/devtree.c
new file mode 100644
index 0000000..bdce0fe
--- /dev/null
+++ b/arch/nds32/kernel/devtree.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/bug.h>
+#include <linux/printk.h>
+#include <linux/of_fdt.h>
+
+void __init early_init_devtree(void *params)
+{
+ if (!params || !early_init_dt_scan(params)) {
+ pr_crit("\n"
+ "Error: invalid device tree blob at (virtual address 0x%p)\n"
+ "\nPlease check your bootloader.", params);
+
+ BUG_ON(1);
+ }
+
+ dump_stack_set_arch_desc("%s (DT)", of_flat_dt_get_machine_name());
+}
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 23/36] nds32: Generic timers support
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds support for timer.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/nds32/kernel/time.c | 11 +++++++++++
1 file changed, 11 insertions(+)
create mode 100644 arch/nds32/kernel/time.c
diff --git a/arch/nds32/kernel/time.c b/arch/nds32/kernel/time.c
new file mode 100644
index 0000000..ac9d78c
--- /dev/null
+++ b/arch/nds32/kernel/time.c
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/clocksource.h>
+#include <linux/clk-provider.h>
+
+void __init time_init(void)
+{
+ of_clk_init(NULL);
+ timer_probe();
+}
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 22/36] nds32: Loadable modules
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds support for loadable modules.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/include/asm/module.h | 11 ++
arch/nds32/kernel/module.c | 286 +++++++++++++++++++++++++++++++++++++++
2 files changed, 297 insertions(+)
create mode 100644 arch/nds32/include/asm/module.h
create mode 100644 arch/nds32/kernel/module.c
diff --git a/arch/nds32/include/asm/module.h b/arch/nds32/include/asm/module.h
new file mode 100644
index 0000000..16cf9c7
--- /dev/null
+++ b/arch/nds32/include/asm/module.h
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef _ASM_NDS32_MODULE_H
+#define _ASM_NDS32_MODULE_H
+
+#include <asm-generic/module.h>
+
+#define MODULE_ARCH_VERMAGIC "NDS32v3"
+
+#endif /* _ASM_NDS32_MODULE_H */
diff --git a/arch/nds32/kernel/module.c b/arch/nds32/kernel/module.c
new file mode 100644
index 0000000..714a6d6
--- /dev/null
+++ b/arch/nds32/kernel/module.c
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/module.h>
+#include <linux/elf.h>
+#include <linux/vmalloc.h>
+
+#include <asm/pgtable.h>
+
+void *module_alloc(unsigned long size)
+{
+ return __vmalloc_node_range(size, 1, MODULES_VADDR, MODULES_END,
+ GFP_KERNEL, PAGE_KERNEL, 0, NUMA_NO_NODE,
+ __builtin_return_address(0));
+}
+
+void module_free(struct module *module, void *region)
+{
+ vfree(region);
+}
+
+int module_frob_arch_sections(Elf_Ehdr * hdr,
+ Elf_Shdr * sechdrs,
+ char *secstrings, struct module *mod)
+{
+ return 0;
+}
+
+void do_reloc16(unsigned int val, unsigned int *loc, unsigned int val_mask,
+ unsigned int val_shift, unsigned int loc_mask,
+ unsigned int partial_in_place, unsigned int swap)
+{
+ unsigned int tmp = 0, tmp2 = 0;
+
+ __asm__ __volatile__("\tlhi.bi\t%0, [%2], 0\n"
+ "\tbeqz\t%3, 1f\n"
+ "\twsbh\t%0, %1\n"
+ "1:\n":"=r"(tmp):"0"(tmp), "r"(loc), "r"(swap)
+ );
+
+ tmp2 = tmp & loc_mask;
+ if (partial_in_place) {
+ tmp &= (!loc_mask);
+ tmp =
+ tmp2 | ((tmp + ((val & val_mask) >> val_shift)) & val_mask);
+ } else {
+ tmp = tmp2 | ((val & val_mask) >> val_shift);
+ }
+
+ __asm__ __volatile__("\tbeqz\t%3, 2f\n"
+ "\twsbh\t%0, %1\n"
+ "2:\n"
+ "\tshi.bi\t%0, [%2], 0\n":"=r"(tmp):"0"(tmp),
+ "r"(loc), "r"(swap)
+ );
+}
+
+void do_reloc32(unsigned int val, unsigned int *loc, unsigned int val_mask,
+ unsigned int val_shift, unsigned int loc_mask,
+ unsigned int partial_in_place, unsigned int swap)
+{
+ unsigned int tmp = 0, tmp2 = 0;
+
+ __asm__ __volatile__("\tlmw.bi\t%0, [%2], %0, 0\n"
+ "\tbeqz\t%3, 1f\n"
+ "\twsbh\t%0, %1\n"
+ "\trotri\t%0, %1, 16\n"
+ "1:\n":"=r"(tmp):"0"(tmp), "r"(loc), "r"(swap)
+ );
+
+ tmp2 = tmp & loc_mask;
+ if (partial_in_place) {
+ tmp &= (!loc_mask);
+ tmp =
+ tmp2 | ((tmp + ((val & val_mask) >> val_shift)) & val_mask);
+ } else {
+ tmp = tmp2 | ((val & val_mask) >> val_shift);
+ }
+
+ __asm__ __volatile__("\tbeqz\t%3, 2f\n"
+ "\twsbh\t%0, %1\n"
+ "\trotri\t%0, %1, 16\n"
+ "2:\n"
+ "\tsmw.bi\t%0, [%2], %0, 0\n":"=r"(tmp):"0"(tmp),
+ "r"(loc), "r"(swap)
+ );
+}
+
+static inline int exceed_limit(int offset, unsigned int val_mask,
+ struct module *module, Elf32_Rela * rel,
+ unsigned int relindex, unsigned int reloc_order)
+{
+ int abs_off = offset < 0 ? ~offset : offset;
+
+ if (abs_off & (~val_mask)) {
+ pr_err("\n%s: relocation type %d out of range.\n"
+ "please rebuild the kernel module with gcc option \"-Wa,-mno-small-text\".\n",
+ module->name, ELF32_R_TYPE(rel->r_info));
+ pr_err("section %d reloc %d offset 0x%x relative 0x%x.\n",
+ relindex, reloc_order, rel->r_offset, offset);
+ return true;
+ }
+ return false;
+}
+
+#ifdef __NDS32_EL__
+#define NEED_SWAP 1
+#else
+#define NEED_SWAP 0
+#endif
+
+int
+apply_relocate_add(Elf32_Shdr * sechdrs, const char *strtab,
+ unsigned int symindex, unsigned int relindex,
+ struct module *module)
+{
+ Elf32_Shdr *symsec = sechdrs + symindex;
+ Elf32_Shdr *relsec = sechdrs + relindex;
+ Elf32_Shdr *dstsec = sechdrs + relsec->sh_info;
+ Elf32_Rela *rel = (void *)relsec->sh_addr;
+ unsigned int i;
+
+ for (i = 0; i < relsec->sh_size / sizeof(Elf32_Rela); i++, rel++) {
+ Elf32_Addr *loc;
+ Elf32_Sym *sym;
+ Elf32_Addr v;
+ s32 offset;
+
+ offset = ELF32_R_SYM(rel->r_info);
+ if (offset < 0
+ || offset > (symsec->sh_size / sizeof(Elf32_Sym))) {
+ pr_err("%s: bad relocation\n", module->name);
+ pr_err("section %d reloc %d\n", relindex, i);
+ return -ENOEXEC;
+ }
+
+ sym = ((Elf32_Sym *) symsec->sh_addr) + offset;
+
+ if (rel->r_offset < 0
+ || rel->r_offset > dstsec->sh_size - sizeof(u16)) {
+ pr_err("%s: out of bounds relocation\n", module->name);
+ pr_err("section %d reloc %d offset 0x%0x size %d\n",
+ relindex, i, rel->r_offset, dstsec->sh_size);
+ return -ENOEXEC;
+ }
+
+ loc = (Elf32_Addr *) (dstsec->sh_addr + rel->r_offset);
+ v = sym->st_value + rel->r_addend;
+
+ switch (ELF32_R_TYPE(rel->r_info)) {
+ case R_NDS32_NONE:
+ case R_NDS32_INSN16:
+ case R_NDS32_LABEL:
+ case R_NDS32_LONGCALL1:
+ case R_NDS32_LONGCALL2:
+ case R_NDS32_LONGCALL3:
+ case R_NDS32_LONGCALL4:
+ case R_NDS32_LONGJUMP1:
+ case R_NDS32_LONGJUMP2:
+ case R_NDS32_LONGJUMP3:
+ case R_NDS32_9_FIXED_RELA:
+ case R_NDS32_15_FIXED_RELA:
+ case R_NDS32_17_FIXED_RELA:
+ case R_NDS32_25_FIXED_RELA:
+ case R_NDS32_LOADSTORE:
+ case R_NDS32_DWARF2_OP1_RELA:
+ case R_NDS32_DWARF2_OP2_RELA:
+ case R_NDS32_DWARF2_LEB_RELA:
+ case R_NDS32_RELA_NOP_MIX ... R_NDS32_RELA_NOP_MAX:
+ break;
+
+ case R_NDS32_32_RELA:
+ do_reloc32(v, loc, 0xffffffff, 0, 0, 0, 0);
+ break;
+
+ case R_NDS32_HI20_RELA:
+ do_reloc32(v, loc, 0xfffff000, 12, 0xfff00000, 0,
+ NEED_SWAP);
+ break;
+
+ case R_NDS32_LO12S3_RELA:
+ do_reloc32(v, loc, 0x00000fff, 3, 0xfffff000, 0,
+ NEED_SWAP);
+ break;
+
+ case R_NDS32_LO12S2_RELA:
+ do_reloc32(v, loc, 0x00000fff, 2, 0xfffff000, 0,
+ NEED_SWAP);
+ break;
+
+ case R_NDS32_LO12S1_RELA:
+ do_reloc32(v, loc, 0x00000fff, 1, 0xfffff000, 0,
+ NEED_SWAP);
+ break;
+
+ case R_NDS32_LO12S0_RELA:
+ case R_NDS32_LO12S0_ORI_RELA:
+ do_reloc32(v, loc, 0x00000fff, 0, 0xfffff000, 0,
+ NEED_SWAP);
+ break;
+
+ case R_NDS32_9_PCREL_RELA:
+ if (exceed_limit
+ ((v - (Elf32_Addr) loc), 0x000000ff, module, rel,
+ relindex, i))
+ return -ENOEXEC;
+ do_reloc16(v - (Elf32_Addr) loc, loc, 0x000001ff, 1,
+ 0xffffff00, 0, NEED_SWAP);
+ break;
+
+ case R_NDS32_15_PCREL_RELA:
+ if (exceed_limit
+ ((v - (Elf32_Addr) loc), 0x00003fff, module, rel,
+ relindex, i))
+ return -ENOEXEC;
+ do_reloc32(v - (Elf32_Addr) loc, loc, 0x00007fff, 1,
+ 0xffffc000, 0, NEED_SWAP);
+ break;
+
+ case R_NDS32_17_PCREL_RELA:
+ if (exceed_limit
+ ((v - (Elf32_Addr) loc), 0x0000ffff, module, rel,
+ relindex, i))
+ return -ENOEXEC;
+ do_reloc32(v - (Elf32_Addr) loc, loc, 0x0001ffff, 1,
+ 0xffff0000, 0, NEED_SWAP);
+ break;
+
+ case R_NDS32_25_PCREL_RELA:
+ if (exceed_limit
+ ((v - (Elf32_Addr) loc), 0x00ffffff, module, rel,
+ relindex, i))
+ return -ENOEXEC;
+ do_reloc32(v - (Elf32_Addr) loc, loc, 0x01ffffff, 1,
+ 0xff000000, 0, NEED_SWAP);
+ break;
+ case R_NDS32_WORD_9_PCREL_RELA:
+ if (exceed_limit
+ ((v - (Elf32_Addr) loc), 0x000000ff, module, rel,
+ relindex, i))
+ return -ENOEXEC;
+ do_reloc32(v - (Elf32_Addr) loc, loc, 0x000001ff, 1,
+ 0xffffff00, 0, NEED_SWAP);
+ break;
+
+ case R_NDS32_SDA15S3_RELA:
+ case R_NDS32_SDA15S2_RELA:
+ case R_NDS32_SDA15S1_RELA:
+ case R_NDS32_SDA15S0_RELA:
+ pr_err("%s: unsupported relocation type %d.\n",
+ module->name, ELF32_R_TYPE(rel->r_info));
+ pr_err
+ ("Small data section access doesn't work in the kernel space; "
+ "please rebuild the kernel module with gcc option -mcmodel=large.\n");
+ pr_err("section %d reloc %d offset 0x%x size %d\n",
+ relindex, i, rel->r_offset, dstsec->sh_size);
+ break;
+
+ default:
+ pr_err("%s: unsupported relocation type %d.\n",
+ module->name, ELF32_R_TYPE(rel->r_info));
+ pr_err("section %d reloc %d offset 0x%x size %d\n",
+ relindex, i, rel->r_offset, dstsec->sh_size);
+ }
+ }
+ return 0;
+}
+
+int
+apply_relocate(Elf32_Shdr * sechdrs, const char *strtab,
+ unsigned int symindex, unsigned int relsec,
+ struct module *module)
+{
+ return 0;
+}
+
+int
+module_finalize(const Elf32_Ehdr * hdr, const Elf_Shdr * sechdrs,
+ struct module *module)
+{
+ return 0;
+}
+
+void module_arch_cleanup(struct module *mod)
+{
+}
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 21/36] nds32: L2 cache support
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds L2 cache support.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/include/asm/l2_cache.h | 142 +++++++++++++++++++++++++++++++++++++
arch/nds32/kernel/atl2c.c | 64 +++++++++++++++++
2 files changed, 206 insertions(+)
create mode 100644 arch/nds32/include/asm/l2_cache.h
create mode 100644 arch/nds32/kernel/atl2c.c
diff --git a/arch/nds32/include/asm/l2_cache.h b/arch/nds32/include/asm/l2_cache.h
new file mode 100644
index 0000000..7706dd0
--- /dev/null
+++ b/arch/nds32/include/asm/l2_cache.h
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef L2_CACHE_H
+#define L2_CACHE_H
+
+/* CCTL_CMD_OP */
+#define L2_CA_CONF_OFF 0x0
+#define L2_IF_CONF_OFF 0x4
+#define L2CC_SETUP_OFF 0x8
+#define L2CC_PROT_OFF 0xC
+#define L2CC_CTRL_OFF 0x10
+#define L2_INT_EN_OFF 0x20
+#define L2_STA_OFF 0x24
+#define RDERR_ADDR_OFF 0x28
+#define WRERR_ADDR_OFF 0x2c
+#define EVDPTERR_ADDR_OFF 0x30
+#define IMPL3ERR_ADDR_OFF 0x34
+#define L2_CNT0_CTRL_OFF 0x40
+#define L2_EVNT_CNT0_OFF 0x44
+#define L2_CNT1_CTRL_OFF 0x48
+#define L2_EVNT_CNT1_OFF 0x4c
+#define L2_CCTL_CMD_OFF 0x60
+#define L2_CCTL_STATUS_OFF 0x64
+#define L2_LINE_TAG_OFF 0x68
+#define L2_LINE_DPT_OFF 0x70
+
+#define CCTL_CMD_L2_IX_INVAL 0x0
+#define CCTL_CMD_L2_PA_INVAL 0x1
+#define CCTL_CMD_L2_IX_WB 0x2
+#define CCTL_CMD_L2_PA_WB 0x3
+#define CCTL_CMD_L2_PA_WBINVAL 0x5
+#define CCTL_CMD_L2_SYNC 0xa
+
+/* CCTL_CMD_TYPE */
+#define CCTL_SINGLE_CMD 0
+#define CCTL_BLOCK_CMD 0x10
+#define CCTL_ALL_CMD 0x10
+
+/******************************************************************************
+ * L2_CA_CONF (Cache architecture configuration)
+ *****************************************************************************/
+#define L2_CA_CONF_offL2SET 0
+#define L2_CA_CONF_offL2WAY 4
+#define L2_CA_CONF_offL2CLSZ 8
+#define L2_CA_CONF_offL2DW 11
+#define L2_CA_CONF_offL2PT 14
+#define L2_CA_CONF_offL2VER 16
+
+#define L2_CA_CONF_mskL2SET (0xFUL << L2_CA_CONF_offL2SET)
+#define L2_CA_CONF_mskL2WAY (0xFUL << L2_CA_CONF_offL2WAY)
+#define L2_CA_CONF_mskL2CLSZ (0x7UL << L2_CA_CONF_offL2CLSZ)
+#define L2_CA_CONF_mskL2DW (0x7UL << L2_CA_CONF_offL2DW)
+#define L2_CA_CONF_mskL2PT (0x3UL << L2_CA_CONF_offL2PT)
+#define L2_CA_CONF_mskL2VER (0xFFFFUL << L2_CA_CONF_offL2VER)
+
+/******************************************************************************
+ * L2CC_SETUP (L2CC Setup register)
+ *****************************************************************************/
+#define L2CC_SETUP_offPART 0
+#define L2CC_SETUP_mskPART (0x3UL << L2CC_SETUP_offPART)
+#define L2CC_SETUP_offDDLATC 4
+#define L2CC_SETUP_mskDDLATC (0x3UL << L2CC_SETUP_offDDLATC)
+#define L2CC_SETUP_offTDLATC 8
+#define L2CC_SETUP_mskTDLATC (0x3UL << L2CC_SETUP_offTDLATC)
+
+/******************************************************************************
+ * L2CC_PROT (L2CC Protect register)
+ *****************************************************************************/
+#define L2CC_PROT_offMRWEN 31
+#define L2CC_PROT_mskMRWEN (0x1UL << L2CC_PROT_offMRWEN)
+
+/******************************************************************************
+ * L2_CCTL_STATUS_Mn (The L2CCTL command working status for Master n)
+ *****************************************************************************/
+#define L2CC_CTRL_offEN 31
+#define L2CC_CTRL_mskEN (0x1UL << L2CC_CTRL_offEN)
+
+/******************************************************************************
+ * L2_CCTL_STATUS_Mn (The L2CCTL command working status for Master n)
+ *****************************************************************************/
+#define L2_CCTL_STATUS_offCMD_COMP 31
+#define L2_CCTL_STATUS_mskCMD_COMP (0x1 << L2_CCTL_STATUS_offCMD_COMP)
+
+#ifndef __ASSEMBLY__
+extern void __iomem *atl2c_base;
+
+#include <linux/smp.h>
+#include <asm/io.h>
+#include <asm/bitfield.h>
+
+#define L2C_R_REG(offset) readl(atl2c_base + offset)
+#define L2C_W_REG(offset, value) writel(value, atl2c_base + offset)
+
+#define L2_CMD_RDY() \
+ do{;}while((L2C_R_REG(L2_CCTL_STATUS_OFF) & L2_CCTL_STATUS_mskCMD_COMP) == 0)
+
+static inline unsigned long L2_CACHE_SET(void)
+{
+ return 64 << ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2SET) >>
+ L2_CA_CONF_offL2SET);
+}
+
+static inline unsigned long L2_CACHE_WAY(void)
+{
+ return 1 +
+ ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2WAY) >>
+ L2_CA_CONF_offL2WAY);
+}
+
+static inline unsigned long L2_CACHE_LINE_SIZE(void)
+{
+
+ return 4 << ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2CLSZ) >>
+ L2_CA_CONF_offL2CLSZ);
+}
+
+static inline unsigned long GET_L2CC_CTRL_CPU(unsigned long cpu)
+{
+ if (cpu == smp_processor_id())
+ return L2C_R_REG(L2CC_CTRL_OFF);
+ return L2C_R_REG(L2CC_CTRL_OFF + (cpu << 8));
+}
+
+static inline void SET_L2CC_CTRL_CPU(unsigned long cpu, unsigned long val)
+{
+ if (cpu == smp_processor_id())
+ L2C_W_REG(L2CC_CTRL_OFF, val);
+ else
+ L2C_W_REG(L2CC_CTRL_OFF + (cpu << 8), val);
+}
+
+static inline unsigned long GET_L2CC_STATUS_CPU(unsigned long cpu)
+{
+ if (cpu == smp_processor_id())
+ return L2C_R_REG(L2_CCTL_STATUS_OFF);
+ return L2C_R_REG(L2_CCTL_STATUS_OFF + (cpu << 8));
+}
+
+#endif
+
+#endif
diff --git a/arch/nds32/kernel/atl2c.c b/arch/nds32/kernel/atl2c.c
new file mode 100644
index 0000000..0c6d031
--- /dev/null
+++ b/arch/nds32/kernel/atl2c.c
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/compiler.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <asm/l2_cache.h>
+
+void __iomem *atl2c_base;
+static const struct of_device_id atl2c_ids[] __initconst = {
+ {.compatible = "andestech,atl2c",}
+};
+
+static int __init atl2c_of_init(void)
+{
+ struct device_node *np;
+ struct resource res;
+ unsigned long tmp = 0;
+ unsigned long l2set, l2way, l2clsz;
+
+ if (!(__nds32__mfsr(NDS32_SR_MSC_CFG) & MSC_CFG_mskL2C))
+ return -ENODEV;
+
+ np = of_find_matching_node(NULL, atl2c_ids);
+ if (!np)
+ return -ENODEV;
+
+ if (of_address_to_resource(np, 0, &res))
+ return -ENODEV;
+
+ atl2c_base = ioremap(res.start, resource_size(&res));
+ if (!atl2c_base)
+ return -ENOMEM;
+
+ l2set =
+ 64 << ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2SET) >>
+ L2_CA_CONF_offL2SET);
+ l2way =
+ 1 +
+ ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2WAY) >>
+ L2_CA_CONF_offL2WAY);
+ l2clsz =
+ 4 << ((L2C_R_REG(L2_CA_CONF_OFF) & L2_CA_CONF_mskL2CLSZ) >>
+ L2_CA_CONF_offL2CLSZ);
+ pr_info("L2:%luKB/%luS/%luW/%luB\n",
+ l2set * l2way * l2clsz / 1024, l2set, l2way, l2clsz);
+
+ tmp = L2C_R_REG(L2CC_PROT_OFF);
+ tmp &= ~L2CC_PROT_mskMRWEN;
+ L2C_W_REG(L2CC_PROT_OFF, tmp);
+
+ tmp = L2C_R_REG(L2CC_SETUP_OFF);
+ tmp &= ~L2CC_SETUP_mskPART;
+ L2C_W_REG(L2CC_SETUP_OFF, tmp);
+
+ tmp = L2C_R_REG(L2CC_CTRL_OFF);
+ tmp |= L2CC_CTRL_mskEN;
+ L2C_W_REG(L2CC_CTRL_OFF, tmp);
+
+ return 0;
+}
+
+subsys_initcall(atl2c_of_init);
--
1.7.9.5
^ permalink raw reply related
* [PATCH v4 20/36] nds32: Debugging support
From: Greentime Hu @ 2017-12-18 6:46 UTC (permalink / raw)
To: greentime, linux-kernel, arnd, linux-arch, tglx, jason,
marc.zyngier, robh+dt, netdev, deanbo422, devicetree, viro,
dhowells, will.deacon, daniel.lezcano, linux-serial,
geert.uytterhoeven, linus.walleij, mark.rutland, greg, ren_guo,
pombredanne
Cc: green.hu, Vincent Chen
In-Reply-To: <cover.1513577007.git.green.hu@gmail.com>
From: Greentime Hu <greentime@andestech.com>
This patch adds ptrace support.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
---
arch/nds32/include/uapi/asm/ptrace.h | 25 +++
arch/nds32/kernel/ptrace.c | 311 ++++++++++++++++++++++++++++++++++
2 files changed, 336 insertions(+)
create mode 100644 arch/nds32/include/uapi/asm/ptrace.h
create mode 100644 arch/nds32/kernel/ptrace.c
diff --git a/arch/nds32/include/uapi/asm/ptrace.h b/arch/nds32/include/uapi/asm/ptrace.h
new file mode 100644
index 0000000..358c99e
--- /dev/null
+++ b/arch/nds32/include/uapi/asm/ptrace.h
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#ifndef __UAPI_ASM_NDS32_PTRACE_H
+#define __UAPI_ASM_NDS32_PTRACE_H
+
+#ifndef __ASSEMBLY__
+
+/*
+ * User structures for general purpose register.
+ */
+struct user_pt_regs {
+ long uregs[26];
+ long fp;
+ long gp;
+ long lp;
+ long sp;
+ long ipc;
+ long lb;
+ long le;
+ long lc;
+ long syscallno;
+};
+#endif
+#endif
diff --git a/arch/nds32/kernel/ptrace.c b/arch/nds32/kernel/ptrace.c
new file mode 100644
index 0000000..0e18564
--- /dev/null
+++ b/arch/nds32/kernel/ptrace.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2005-2017 Andes Technology Corporation
+
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/smp.h>
+#include <linux/ptrace.h>
+#include <linux/user.h>
+#include <linux/security.h>
+#include <linux/init.h>
+#include <linux/uaccess.h>
+#include <linux/regset.h>
+#include <linux/tracehook.h>
+#include <linux/elf.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/pgtable.h>
+
+enum nds32_regset {
+ REGSET_GPR,
+};
+
+static int gpr_get(struct task_struct *target,
+ const struct user_regset *regset,
+ unsigned int pos, unsigned int count,
+ void *kbuf, void __user * ubuf)
+{
+ struct user_pt_regs *uregs = &task_pt_regs(target)->user_regs;
+ return user_regset_copyout(&pos, &count, &kbuf, &ubuf, uregs, 0, -1);
+}
+
+static int gpr_set(struct task_struct *target, const struct user_regset *regset,
+ unsigned int pos, unsigned int count,
+ const void *kbuf, const void __user * ubuf)
+{
+ int err;
+ struct user_pt_regs newregs = task_pt_regs(target)->user_regs;
+
+ err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &newregs, 0, -1);
+ if (err)
+ return err;
+
+ task_pt_regs(target)->user_regs = newregs;
+ return 0;
+}
+
+static const struct user_regset nds32_regsets[] = {
+ [REGSET_GPR] = {
+ .core_note_type = NT_PRSTATUS,
+ .n = sizeof(struct user_pt_regs) / sizeof(u32),
+ .size = sizeof(u32),
+ .align = sizeof(u32),
+ .get = gpr_get,
+ .set = gpr_set}
+};
+
+static const struct user_regset_view nds32_user_view = {
+ .name = "nds32",.e_machine = EM_NDS32,
+ .regsets = nds32_regsets,.n = ARRAY_SIZE(nds32_regsets)
+};
+
+const struct user_regset_view *task_user_regset_view(struct task_struct *task)
+{
+ return &nds32_user_view;
+}
+
+/* get_user_reg()
+ *
+ * This routine will get a word off of the processes privileged stack.
+ * the offset is how far from the base addr as stored in the THREAD.
+ * this routine assumes that all the privileged stacks are in our
+ * data space.
+ */
+static inline unsigned int get_user_reg(struct task_struct *task, int offset)
+{
+ return task_pt_regs(task)->uregs[offset];
+}
+
+/* put_user_reg()
+ *
+ * this routine will put a word on the processes privileged stack.
+ * the offset is how far from the base addr as stored in the THREAD.
+ * this routine assumes that all the privileged stacks are in our
+ * data space.
+ */
+static inline int put_user_reg(struct task_struct *task, int offset, long data)
+{
+ struct pt_regs newregs, *regs = task_pt_regs(task);
+ int ret = -EINVAL;
+
+ newregs = *regs;
+ newregs.uregs[offset] = data;
+
+ if (valid_user_regs(&newregs)) {
+ regs->uregs[offset] = data;
+ ret = 0;
+ }
+
+ return ret;
+}
+
+/*
+ * Called by kernel/ptrace.c when detaching..
+ *
+ * Make sure the single step bit is not set.
+ */
+void ptrace_disable(struct task_struct *child)
+{
+ user_disable_single_step(child);
+}
+
+static void fill_sigtrap_info(struct task_struct *tsk,
+ struct pt_regs *regs,
+ int error_code, int si_code, struct siginfo *info)
+{
+ tsk->thread.trap_no = ENTRY_DEBUG_RELATED;
+ tsk->thread.error_code = error_code;
+
+ memset(info, 0, sizeof(*info));
+ info->si_signo = SIGTRAP;
+ info->si_code = si_code;
+ info->si_addr = (void __user *)instruction_pointer(regs);
+}
+
+void user_single_step_siginfo(struct task_struct *tsk,
+ struct pt_regs *regs, struct siginfo *info)
+{
+ fill_sigtrap_info(tsk, regs, 0, TRAP_BRKPT, info);
+}
+
+/*
+ * Handle hitting a breakpoint.
+ */
+void send_sigtrap(struct task_struct *tsk, struct pt_regs *regs,
+ int error_code, int si_code)
+{
+ struct siginfo info;
+
+ fill_sigtrap_info(tsk, regs, error_code, TRAP_BRKPT, &info);
+ /* Send us the fake SIGTRAP */
+ force_sig_info(SIGTRAP, &info, tsk);
+}
+
+/* ptrace_read_user()
+ *
+ * Read the word at offset "off" into the "struct user". We
+ * actually access the pt_regs stored on the kernel stack.
+ */
+static int
+ptrace_read_user(struct task_struct *tsk, unsigned long off,
+ unsigned long __user * ret)
+{
+ unsigned long tmp = 0;
+
+ if (off < sizeof(struct pt_regs)) {
+ if (off & 3)
+ return -EIO;
+ tmp = get_user_reg(tsk, off >> 2);
+ return put_user(tmp, ret);
+ } else
+ return -EIO;
+}
+
+/* ptrace_write_user()
+ *
+ * Write the word at offset "off" into "struct user". We
+ * actually access the pt_regs stored on the kernel stack.
+ */
+static int
+ptrace_write_user(struct task_struct *tsk, unsigned long off, unsigned long val)
+{
+ if (off < sizeof(struct pt_regs)) {
+ if (off & 3)
+ return -EIO;
+ return put_user_reg(tsk, off >> 2, val);
+ } else
+ return -EIO;
+}
+
+/* ptrace_getregs()
+ *
+ * Get all user integer registers.
+ */
+static int ptrace_getregs(struct task_struct *tsk, void __user * uregs)
+{
+ struct pt_regs *regs = task_pt_regs(tsk);
+
+ return copy_to_user(uregs, regs, sizeof(struct pt_regs)) ? -EFAULT : 0;
+}
+
+/* ptrace_setregs()
+ *
+ * Set all user integer registers.
+ */
+static int ptrace_setregs(struct task_struct *tsk, void __user * uregs)
+{
+ struct pt_regs newregs;
+ int ret;
+
+ ret = -EFAULT;
+ if (copy_from_user(&newregs, uregs, sizeof(struct pt_regs)) == 0) {
+ struct pt_regs *regs = task_pt_regs(tsk);
+
+ ret = -EINVAL;
+ if (valid_user_regs(&newregs)) {
+ *regs = newregs;
+ ret = 0;
+ }
+ }
+
+ return ret;
+}
+
+/* ptrace_getfpregs()
+ *
+ * Get the child FPU state.
+ */
+static int ptrace_getfpregs(struct task_struct *tsk, void __user * ufpregs)
+{
+ return -EFAULT;
+}
+
+/*
+ * Set the child FPU state.
+ */
+static int ptrace_setfpregs(struct task_struct *tsk, void __user * ufpregs)
+{
+ return -EFAULT;
+}
+
+/* do_ptrace()
+ *
+ * Provide ptrace defined service.
+ */
+long arch_ptrace(struct task_struct *child, long request, unsigned long addr,
+ unsigned long data)
+{
+ int ret;
+
+ switch (request) {
+ case PTRACE_PEEKUSR:
+ ret =
+ ptrace_read_user(child, addr, (unsigned long __user *)data);
+ break;
+
+ case PTRACE_POKEUSR:
+ ret = ptrace_write_user(child, addr, data);
+ break;
+
+ case PTRACE_GETREGS:
+ ret = ptrace_getregs(child, (void __user *)data);
+ break;
+
+ case PTRACE_SETREGS:
+ ret = ptrace_setregs(child, (void __user *)data);
+ break;
+
+ case PTRACE_GETFPREGS:
+ ret = ptrace_getfpregs(child, (void __user *)data);
+ break;
+
+ case PTRACE_SETFPREGS:
+ ret = ptrace_setfpregs(child, (void __user *)data);
+ break;
+
+ default:
+ ret = ptrace_request(child, request, addr, data);
+ break;
+ }
+
+ return ret;
+}
+
+void user_enable_single_step(struct task_struct *child)
+{
+ struct pt_regs *regs;
+ regs = task_pt_regs(child);
+ regs->ipsw |= PSW_mskHSS;
+ set_tsk_thread_flag(child, TIF_SINGLESTEP);
+}
+
+void user_disable_single_step(struct task_struct *child)
+{
+ struct pt_regs *regs;
+ regs = task_pt_regs(child);
+ regs->ipsw &= ~PSW_mskHSS;
+ clear_tsk_thread_flag(child, TIF_SINGLESTEP);
+}
+
+/* sys_trace()
+ *
+ * syscall trace handler.
+ */
+
+asmlinkage int syscall_trace_enter(int syscall, struct pt_regs *regs)
+{
+ if (test_thread_flag(TIF_SYSCALL_TRACE)) {
+ if (tracehook_report_syscall_entry(regs))
+ return -1;
+ }
+ return syscall;
+}
+
+asmlinkage void syscall_trace_leave(struct pt_regs *regs)
+{
+ int step = test_thread_flag(TIF_SINGLESTEP);
+ if (step || test_thread_flag(TIF_SYSCALL_TRACE))
+ tracehook_report_syscall_exit(regs, step);
+
+}
--
1.7.9.5
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox