From: Arnd Hannemann <arnd@arndnet.de>
To: linux-mmc@vger.kernel.org
Cc: linux-sh@vger.kernel.org, g.liakhovetski@gmx.de,
Arnd Hannemann <arnd@arndnet.de>
Subject: [PATCH 2/4] ARM: mach-shmobile: sh7372 Enable SDIO IRQs
Date: Mon, 06 Dec 2010 17:35:40 +0000 [thread overview]
Message-ID: <1291656942-18100-2-git-send-email-arnd@arndnet.de> (raw)
In-Reply-To: <1291656942-18100-1-git-send-email-arnd@arndnet.de>
This patch enables the interrupt generation for SDIO IRQs
of the sdhi controllers of the soc. To make sure interrupts
are handled announce the MMC_CAP_SDIO_IRQ capability
on AP4EVB. Tested with a b43-based SDIO wireless card.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
---
arch/arm/mach-shmobile/board-ap4evb.c | 3 ++-
arch/arm/mach-shmobile/intc-sh7372.c | 4 ++--
2 files changed, 4 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c
index 16eba07..5763b0d 100644
--- a/arch/arm/mach-shmobile/board-ap4evb.c
+++ b/arch/arm/mach-shmobile/board-ap4evb.c
@@ -310,6 +310,7 @@ static u64 sdhi0_dma_mask = DMA_BIT_MASK(32);
static struct sh_mobile_sdhi_info sdhi0_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
+ .tmio_caps = MMC_CAP_SDIO_IRQ,
};
static struct resource sdhi0_resources[] = {
@@ -344,7 +345,7 @@ static struct sh_mobile_sdhi_info sdhi1_info = {
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
.tmio_ocr_mask = MMC_VDD_165_195,
.tmio_flags = TMIO_MMC_WRPROTECT_DISABLE,
- .tmio_caps = MMC_CAP_NEEDS_POLL,
+ .tmio_caps = MMC_CAP_NEEDS_POLL | MMC_CAP_SDIO_IRQ,
.get_cd = slot_cn7_get_cd,
};
diff --git a/arch/arm/mach-shmobile/intc-sh7372.c b/arch/arm/mach-shmobile/intc-sh7372.c
index 30b2f40..f78a1ea 100644
--- a/arch/arm/mach-shmobile/intc-sh7372.c
+++ b/arch/arm/mach-shmobile/intc-sh7372.c
@@ -230,10 +230,10 @@ static struct intc_mask_reg intca_mask_registers[] __initdata = {
{ SCIFB, SCIFA5, SCIFA4, MSIOF1,
0, 0, MSIOF2, 0 } },
{ 0xe694009c, 0xe69400dc, 8, /* IMR7A / IMCR7A */
- { DISABLED, DISABLED, ENABLED, ENABLED,
+ { DISABLED, ENABLED, ENABLED, ENABLED,
FLCTL_FLTREQ1I, FLCTL_FLTREQ0I, FLCTL_FLTENDI, FLCTL_FLSTEI } },
{ 0xe69400a0, 0xe69400e0, 8, /* IMR8A / IMCR8A */
- { 0, DISABLED, ENABLED, ENABLED,
+ { 0, ENABLED, ENABLED, ENABLED,
TTI20, USBHSDMAC0_USHDMI, 0, 0 } },
{ 0xe69400a4, 0xe69400e4, 8, /* IMR9A / IMCR9A */
{ CMT1_CMT13, CMT1_CMT12, CMT1_CMT11, CMT1_CMT10,
--
1.7.0.4
next prev parent reply other threads:[~2010-12-06 17:35 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-06 17:35 [PATCH 1/4] mmc: tmio: Implement SDIO IRQ Arnd Hannemann
2010-12-06 17:35 ` Arnd Hannemann [this message]
2010-12-06 17:35 ` [PATCH 3/4] sh: sh7724 Enable SDIO IRQs Arnd Hannemann
2010-12-06 17:35 ` [PATCH 4/4] [RFC] sh: sh7722 " Arnd Hannemann
2010-12-07 5:39 ` [PATCH 1/4] mmc: tmio: Implement SDIO IRQ Magnus Damm
2010-12-07 12:22 ` Arnd Hannemann
2010-12-07 14:37 ` Magnus Damm
2010-12-07 15:08 ` Arnd Hannemann
2010-12-14 15:44 ` Magnus Damm
2010-12-20 3:58 ` Magnus Damm
2010-12-20 15:51 ` Arnd Hannemann
2010-12-20 15:53 ` [PATCH 0/6 v2] mmc: tmio: Add SDIO IRQ support Arnd Hannemann
2010-12-22 13:54 ` Magnus Damm
2010-12-23 10:45 ` [PATCH] [RFC] sh: sh7723 / ap325rxa enable SDIO IRQs Arnd Hannemann
2010-12-28 10:01 ` Magnus Damm
2010-12-20 15:53 ` [PATCH 1/6 v2] mmc: tmio: implement SDIO IRQ Arnd Hannemann
2010-12-20 15:53 ` [PATCH 2/6 v2] mfd: sh_mobile_sdhi: activate SDIO IRQ for tmio_mmc Arnd Hannemann
2010-12-24 11:03 ` [PATCH 2/6 v2] mfd: sh_mobile_sdhi: activate SDIO IRQ for Samuel Ortiz
2010-12-20 15:53 ` [PATCH 3/6 v2] mmc: tmio: disable IRQs early in remove Arnd Hannemann
2010-12-20 15:53 ` [PATCH 4/6 v2] ARM: mach-shmobile: sh7372 Enable SDIO IRQs Arnd Hannemann
2010-12-20 15:53 ` [PATCH 5/6 v2] sh: sh7724 " Arnd Hannemann
2010-12-20 15:53 ` [PATCH 6/6 v2] [RFC] sh: sh7722 " Arnd Hannemann
2010-12-23 10:42 ` [PATCH 6/6 v3] " Arnd Hannemann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1291656942-18100-2-git-send-email-arnd@arndnet.de \
--to=arnd@arndnet.de \
--cc=g.liakhovetski@gmx.de \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).