From mboxrd@z Thu Jan 1 00:00:00 1970 From: Geert Uytterhoeven Date: Thu, 22 May 2014 18:07:35 +0000 Subject: [PATCH] spi: rspi: Round up division to avoid slave overclocking Message-Id: <1400782055-19609-1-git-send-email-geert+renesas@glider.be> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: Mark Brown , Simon Horman Cc: linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-sh-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Geert Uytterhoeven The calculation of the bit rate divider used a standard C division, which rounds down the quotient. This may lead to a higher bitrate than requested. Round up to avoid this. E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75 MHz. After this patch it's driven at a safe 24.375 MHz. Signed-off-by: Geert Uytterhoeven --- Simon: I think you want this in renesas-backports. drivers/spi/spi-rspi.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 1fb0ad213324..5639f9529e0b 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -266,7 +266,8 @@ static int rspi_set_config_register(struct rspi_data *rspi, int access_size) rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ - spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz) - 1; + spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), + 2 * rspi->max_speed_hz) - 1; rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); /* Disable dummy transmission, set 16-bit word access, 1 frame */ @@ -302,7 +303,8 @@ static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size) rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ - spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz) - 1; + spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), + 2 * rspi->max_speed_hz) - 1; rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); /* Disable dummy transmission, set byte access */ @@ -335,7 +337,7 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size) rspi_write8(rspi, rspi->sppcr, RSPI_SPPCR); /* Sets transfer bit rate */ - spbr = clk_get_rate(rspi->clk) / (2 * rspi->max_speed_hz); + spbr = DIV_ROUND_UP(clk_get_rate(rspi->clk), 2 * rspi->max_speed_hz); rspi_write8(rspi, clamp(spbr, 0, 255), RSPI_SPBR); /* Disable dummy transmission, set byte access */ -- 1.9.1