From: Magnus Damm <magnus.damm@gmail.com>
To: linux-sh@vger.kernel.org
Subject: [PATCH 01/03] ARM: shmobile: r8a7790: SYS-DMAC prototype
Date: Tue, 03 Jun 2014 22:33:04 +0000 [thread overview]
Message-ID: <20140603223304.2193.1096.sendpatchset@w520> (raw)
From: Magnus Damm <damm+renesas@opensource.se>
Prototype code to enable part of the SYS-DMAC on r8a7790.
Written to exercise the SYS-DMAC - Not for upstream merge.
Based on the following patch by Kuninori Morimoto-san:
"Local: ARM: shmobile: r8a7790: add SYS-DMAC support"
This patch enables SYS-DMAC0 (= Low), it doesn't support
SYS-DMAC1 (= HI) today.
Because, SYS-DMAC HI/Low interrupt mapping is not
good match to SH-DMAC driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: Do not call r8a7790_register_sys_dmac()
in r8a7790_add_standard_devices() as it is already called via
r8a7790_add_dt_devices()]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[damm+renesas@opensource.se: Remove SDHI bits, also remove legacy
code path to make sure to cover only the DT reference case]
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
---
Applies to renesas-devel-v3.15-rc7-20140530
arch/arm/mach-shmobile/setup-r8a7790.c | 89 ++++++++++++++++++++++++++++----
1 file changed, 80 insertions(+), 9 deletions(-)
--- 0001/arch/arm/mach-shmobile/setup-r8a7790.c
+++ work/arch/arm/mach-shmobile/setup-r8a7790.c 2014-06-03 21:24:37.000000000 +0900
@@ -32,6 +32,84 @@
#include <mach/r8a7790.h>
#include <asm/mach/arch.h>
+#define DMAE_CHANNEL(a, b) \
+{ \
+ .offset = (a) - 0x20, \
+ .dmars = (a) - 0x20 + 0x40, \
+ .chclr_bit = (b), \
+ .chclr_offset = 0x80 - 0x20, \
+}
+
+/* Sys-DMAC */
+#define SYS_DMAC_SLAVE(_id, _bit, _addr, toffset, roffset, t, r) \
+{ \
+ .slave_id = SYS_DMAC_SLAVE_## _id ##_TX, \
+ .addr = _addr + toffset, \
+ .chcr = CHCR_TX(XMIT_SZ_## _bit ##BIT), \
+ .mid_rid = t, \
+}, { \
+ .slave_id = SYS_DMAC_SLAVE_## _id ##_RX, \
+ .addr = _addr + roffset, \
+ .chcr = CHCR_RX(XMIT_SZ_## _bit ##BIT), \
+ .mid_rid = r, \
+}
+
+static const struct sh_dmae_slave_config r8a7790_sys_dmac_slaves[] = {
+};
+
+static const struct sh_dmae_channel r8a7790_sys_dmac_channels[] = {
+ DMAE_CHANNEL(0x8000, 0),
+ DMAE_CHANNEL(0x8080, 1),
+ DMAE_CHANNEL(0x8100, 2),
+ DMAE_CHANNEL(0x8180, 3),
+ DMAE_CHANNEL(0x8200, 4),
+ DMAE_CHANNEL(0x8280, 5),
+ DMAE_CHANNEL(0x8300, 6),
+ DMAE_CHANNEL(0x8380, 7),
+ DMAE_CHANNEL(0x8400, 8),
+ DMAE_CHANNEL(0x8480, 9),
+ DMAE_CHANNEL(0x8500, 10),
+ DMAE_CHANNEL(0x8580, 11),
+ DMAE_CHANNEL(0x8600, 12),
+ DMAE_CHANNEL(0x8680, 13),
+ DMAE_CHANNEL(0x8700, 14),
+};
+
+static struct sh_dmae_pdata r8a7790_sys_dmac_platform_data = {
+ .slave = r8a7790_sys_dmac_slaves,
+ .slave_num = ARRAY_SIZE(r8a7790_sys_dmac_slaves),
+ .channel = r8a7790_sys_dmac_channels,
+ .channel_num = ARRAY_SIZE(r8a7790_sys_dmac_channels),
+ .ts_low_shift = TS_LOW_SHIFT,
+ .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
+ .ts_high_shift = TS_HI_SHIFT,
+ .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
+ .ts_shift = dma_ts_shift,
+ .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
+ .dmaor_init = DMAOR_DME,
+ .chclr_present = 1,
+ .chclr_bitwise = 1,
+};
+
+static struct resource r8a7790_sys_dmac_resources[] = {
+ /* Channel registers and DMAOR for low */
+ DEFINE_RES_MEM(0xe6700020, 0x8763 - 0x20),
+ DEFINE_RES_IRQ(gic_spi(197)),
+ DEFINE_RES_NAMED(gic_spi(200), 15, NULL, IORESOURCE_IRQ),
+
+ /*
+ * HI is not supported
+ * since IRQ has strange mapping
+ */
+};
+
+#define r8a7790_register_sys_dmac(id) \
+ platform_device_register_resndata( \
+ &platform_bus, "sh-dma-engine", 2 + id, \
+ &r8a7790_sys_dmac_resources[id * 3], 3, \
+ &r8a7790_sys_dmac_platform_data, \
+ sizeof(r8a7790_sys_dmac_platform_data))
+
/* Audio-DMAC */
#define AUDIO_DMAC_SLAVE(_id, _addr, t, r) \
{ \
@@ -59,14 +137,6 @@ static const struct sh_dmae_slave_config
AUDIO_DMAC_SLAVE(SSI9, 0xec241240, 0x13, 0x14),
};
-#define DMAE_CHANNEL(a, b) \
-{ \
- .offset = (a) - 0x20, \
- .dmars = (a) - 0x20 + 0x40, \
- .chclr_bit = (b), \
- .chclr_offset = 0x80 - 0x20, \
-}
-
static const struct sh_dmae_channel r8a7790_audio_dmac_channels[] = {
DMAE_CHANNEL(0x8000, 0),
DMAE_CHANNEL(0x8080, 1),
@@ -282,6 +352,7 @@ static struct resource cmt0_resources[]
void __init r8a7790_add_dt_devices(void)
{
r8a7790_register_cmt(0);
+ r8a7790_register_sys_dmac(0);
}
void __init r8a7790_add_standard_devices(void)
@@ -296,7 +367,7 @@ void __init r8a7790_add_standard_devices
r8a7790_register_scif(7);
r8a7790_register_scif(8);
r8a7790_register_scif(9);
- r8a7790_add_dt_devices();
+ r8a7790_register_cmt(0);
r8a7790_register_irqc(0);
r8a7790_register_thermal();
r8a7790_register_i2c(0);
reply other threads:[~2014-06-03 22:33 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140603223304.2193.1096.sendpatchset@w520 \
--to=magnus.damm@gmail.com \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).