From mboxrd@z Thu Jan 1 00:00:00 1970 From: Simon Horman Date: Tue, 10 Mar 2015 01:14:55 +0000 Subject: Re: Can't boot kernel v4.0-rc2 on Koelsch Message-Id: <20150310011454.GA17232@verge.net.au> List-Id: References: <2263226.JPOqZgiCRj@avalon> In-Reply-To: <2263226.JPOqZgiCRj@avalon> MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 8bit To: linux-sh@vger.kernel.org Hi Hiep-san, I'd like to agree with Laurent's observation that this appears to mean that your userspace is broken / needs updating. The boards in question boot to userspace in my environment. On Mon, Mar 09, 2015 at 06:43:54PM +0900, Cao Minh Hiep wrote: > Hi Laurent-san, > Thanks for your comment, > > On 2015年03月09日 16:06, Laurent Pinchart wrote: > >Hello Hiep-san, > > > >On Monday 09 March 2015 10:07:04 Cao Minh Hiep wrote: > >>Hi Laurent-san > >> > >>I am Hiep from Jinzai Solution. > >>I'm sorry to bother you again! > >No worries. > > > >>We are testing the linux ver v4.0-rc2 on Koelsch, We can not boot the > >>kernel v4.0-rc2 on Koelsch, > >>Then we found a patch has changed as below: > >>"1f75cda ARM: shmobile: koelsch: Rename SCIF[01] serial ports to ttySC[01]" > >> > >>Please see it when you have time! > >Could you please detail your boot failure ? You might need to change your > >/etc/inittab to adjust to the serial port new name, but apart from that there > >shouldn't be any issue. I can boot my Koelsch board on 4.0-v2. > Sure, I use the rootfs of Linaro-nano 2014.09 to test v4.0-rc2. > When booting kernel with default config, bootlogs showed until these > messages appearing. > "init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: tty1 main process (1449) killed by TERM signal > init: auto-serial-console respawning too fast, stopped" > > Then, my Koelsch board stoped here.(my Lager board is the same) > (I attached the bootlogs_file) > > So, When I tried to add "console=ttySC0," into bootargs (at .dts file), i > can boot my Koelsch board without any problems. > And these are the same on Lager board. > > Thank you! > Jinso/Hiep > ====> information: > Actually, on v4.0-rc2, we have two patches related each other as below: > 79e69d1 ARM: shmobile: koelsch dts:Drop console= bootargs parameter BAD. > 1f75cda ARM: shmobile: koelsch: Rename SCIF01 serial ports to ttySC01 > > And for Lager: > 569dd56 ARM: shmobile: lager dts: Drop console= bootargs parameter > 78c11ec ARM: shmobile: lager: Rename SCIFA[01] serial ports to ttySC[01] > > There is only 79e69d1 patch on v3.19-rcX, I also had a problem with bootting > Koelsch on v3.19-rcX > (using linaro-nano 2014.09). But it was good on Yocto and > linaro-nano-2013.02 > > > > > > => bootp;bootm > sh_eth Waiting for PHY auto negotiation to complete.. done > sh_eth: 100Base/Full > BOOTP broadcast 1 > DHCP client bound to address 172.16.1.36 > Using sh_eth device > TFTP from server 172.16.1.9; our IP address is 172.16.1.36 > Filename 'Koelsch/uImage.dtb'. > Load address: 0x40007fc0 > Loading: #######################������������������������������������������������������������������������������������0 > Linux version 4.0.0-rc2 (jinso02@jinso02) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-25 > CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), crc5307d > CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache > Machine model: Koelsch > Ignoring memory block 0x200000000 - 0x240000000 > debug: ignoring loglevel setting. > Memory policy: Data cache writealloc > On node 0 totalpages: 262144 > free_area_init_node: node 0, pgdat c063fe00, node_mem_map eeff9000 > Normal zone: 1520 pages used for memmap > Normal zone: 0 pages reserved > Normal zone: 194560 pages, LIFO batch:31 > HighMem zone: 67584 pages, LIFO batch:15 > PERCPU: Embedded 8 pages/cpu @eefca000 s11456 r0 d21312 u32768 > pcpu-alloc: s11456 r0 d21312 u32768 alloc=8*4096 > pcpu-alloc: [0] 0 [0] 1 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624 > Kernel command line: ignore_loglevel rw root=/dev/nfs ip=dhcp > PID hash table entries: 4096 (order: 2, 16384 bytes) > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 1032772K/1048576K available (4636K kernel code, 205K rwdata, 1252K rodata, 272K init, 192K bss, 15804K reser) > Virtual kernel memory layout: > vector : 0xffff0000 - 0xffff1000 ( 4 kB) > fixmap : 0xffc00000 - 0xfff00000 (3072 kB) > vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) > lowmem : 0xc0000000 - 0xef800000 ( 760 MB) > pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > .text : 0xc0008000 - 0xc05c9044 (5893 kB) > .init : 0xc05ca000 - 0xc060e000 ( 272 kB) > .data : 0xc060e000 - 0xc0641720 ( 206 kB) > .bss : 0xc0641720 - 0xc06717ec ( 193 kB) > Hierarchical RCU implementation. > Additional per-CPU info printed with stalls. > RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. > RCU: Adjusting geometry for rcu_fanout_leaf, nr_cpu_ids=2 > NR_IRQS:16 nr_irqs:16 16 > Architected cp15 timer(s) running at 10.00MHz (virt). > sched_clock: 56 bits at 10MHz, resolution 100ns, wraps every 3435973836800ns > Switching to timer-based delay loop, resolution 100ns > Console: colour dummy device 80x30 > console [tty0] enabled > Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj0000) > pid_max: default: 32768 minimum: 301 > Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) > Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) > CPU: Testing write buffer coherency: ok > CPU0: update cpu_capacity 1024 > CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 > Setting up static identity map for 0x4048dba0 - 0x4048dbf8 > Unable to boot CPU1 when MD21 is set > CPU1: failed to boot: -524 > Brought up 1 CPUs > SMP: Total of 1 processors activated (20.00 BogoMIPS). > CPU: All CPU(s) started in SVC mode. > devtmpfs: initialized > VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 > pinctrl core: initialized pinctrl subsystem > NET: Registered protocol family 16 > DMA: preallocated 256 KiB pool for atomic coherent allocations > renesas_irqc e61c0000.interrupt-controller: driving 10 irqs > sh-pfc e6060000.pfc: r8a77910_pfc support registered > No ATAGs? > hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. > hw-breakpoint: maximum watchpoint size is 8 bytes. > platform regulator@0: Driver reg-fixed-voltage requests probe deferral > platform regulator@2: Driver reg-fixed-voltage requests probe deferral > platform regulator@4: Driver reg-fixed-voltage requests probe deferral > gpio-regulator regulator@1: Could not obtain regulator setting GPIOs: -517 > platform regulator@1: Driver gpio-regulator requests probe deferral > gpio-regulator regulator@3: Could not obtain regulator setting GPIOs: -517 > platform regulator@3: Driver gpio-regulator requests probe deferral > gpio-regulator regulator@5: Could not obtain regulator setting GPIOs: -517 > platform regulator@5: Driver gpio-regulator requests probe deferral > vgaarb: loaded > SCSI subsystem initialized > libata version 3.00 loaded. > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > i2c-sh_mobile e60b0000.i2c: I2C adapter 6, bus speed 100000 Hz > media: Linux media interface: v0.10 > Linux video capture interface: v2.00 > sh_cmt ffca0000.timer: ch0: used for clock events > sh_cmt ffca0000.timer: ch1: used as clock source > Advanced Linux Sound Architecture Driver Initialized. > Switched to clocksource arch_sys_counter > NET: Registered protocol family 2 > TCP established hash table entries: 8192 (order: 3, 32768 bytes) > TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > TCP: Hash tables configured (established 8192 bind 8192) > TCP: reno registered > UDP hash table entries: 512 (order: 2, 16384 bytes) > UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) > NET: Registered protocol family 1 > RPC: Registered named UNIX socket transport module. > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > PCI: CLS 0 bytes, default 64 > futex hash table entries: 512 (order: 3, 32768 bytes) > NFS: Registering the id_resolver key type > Key type id_resolver registered > Key type id_legacy registered > nfs4filelayout_init: NFSv4 File Layout Driver Registering... > nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... > bounce: pool size: 64 pages > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) > io scheduler noop registered > io scheduler deadline registered > io scheduler cfq registered (default) > gpio_rcar e6050000.gpio: driving 32 GPIOs > gpio_rcar e6051000.gpio: driving 32 GPIOs > gpio_rcar e6052000.gpio: driving 32 GPIOs > gpio_rcar e6053000.gpio: driving 32 GPIOs > gpio_rcar e6054000.gpio: driving 32 GPIOs > gpio_rcar e6055000.gpio: driving 32 GPIOs > gpio_rcar e6055400.gpio: driving 32 GPIOs > gpio_rcar e6055800.gpio: driving 26 GPIOs > pci-rcar-gen2 ee090000.pci: PCI: bus0 revision 11 > pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00 > pci_bus 0000:00: root bus resource [io 0xee080000-0xee0810ff] > pci_bus 0000:00: root bus resource [mem 0xee080000-0xee0810ff] > pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] > pci 0000:00:00.0: [1033:0000] type 00 class 0x060000 > pci 0000:00:00.0: reg 0x10: [mem 0xee090800-0xee090bff] > pci 0000:00:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref] > pci 0000:00:01.0: [1033:0035] type 00 class 0x0c0310 > pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00000fff] > pci 0000:00:01.0: supports D1 D2 > pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot > pci 0000:00:02.0: [1033:00e0] type 00 class 0x0c0320 > pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x000000ff] > pci 0000:00:02.0: supports D1 D2 > pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot > PCI: bus0: Fast back to back transfers disabled > pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 > pci 0000:00:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed > pci 0000:00:01.0: Can't enable PCI device, BIOS handoff failed. > pci 0000:00:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed > pci 0000:00:02.0: Can't enable PCI device, BIOS handoff failed. > pci 0000:00:01.0: BAR 0: assigned [mem 0xee080000-0xee080fff] > pci 0000:00:02.0: BAR 0: assigned [mem 0xee081000-0xee0810ff] > pci-rcar-gen2 ee0d0000.pci: PCI: bus0 revision 11 > pci-rcar-gen2 ee0d0000.pci: PCI host bridge to bus 0001:01 > pci_bus 0001:01: root bus resource [io 0xee0c0000-0xee0c10ff] > pci_bus 0001:01: root bus resource [mem 0xee0c0000-0xee0c10ff] > pci_bus 0001:01: No busn resource found for root bus, will use [bus 01-ff] > pci 0001:01:00.0: [1033:0000] type 00 class 0x060000 > pci 0001:01:00.0: reg 0x10: [mem 0xee0d0800-0xee0d0bff] > pci 0001:01:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref] > pci 0001:01:01.0: [1033:0035] type 00 class 0x0c0310 > pci 0001:01:01.0: reg 0x10: [mem 0x00000000-0x00000fff] > pci 0001:01:01.0: supports D1 D2 > pci 0001:01:01.0: PME# supported from D0 D1 D2 D3hot > pci 0001:01:02.0: [1033:00e0] type 00 class 0x0c0320 > pci 0001:01:02.0: reg 0x10: [mem 0x00000000-0x000000ff] > pci 0001:01:02.0: supports D1 D2 > pci 0001:01:02.0: PME# supported from D0 D1 D2 D3hot > PCI: bus1: Fast back to back transfers disabled > pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 > pci 0001:01:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed > pci 0001:01:01.0: Can't enable PCI device, BIOS handoff failed. > pci 0001:01:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed > pci 0001:01:02.0: Can't enable PCI device, BIOS handoff failed. > pci 0001:01:01.0: BAR 0: assigned [mem 0xee0c0000-0xee0c0fff] > pci 0001:01:02.0: BAR 0: assigned [mem 0xee0c1000-0xee0c10ff] > rcar-pcie fe000000.pcie: PCIe link down > Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled > SuperH (H)SCI(F) driver initialized > e6e60000.serial: ttySC0 at MMIO 0xe6e60000 (irq = 107, base_baud = 0) is a scif > console [ttySC0] enabled > e6e68000.serial: ttySC1 at MMIO 0xe6e68000 (irq = 108, base_baud = 0) is a scif > [drm] Initialized drm 1.1.0 20060810 > rcar-du feb00000.display: error: no encoder could be initialized > rcar-du feb00000.display: failed to initialize DRM/KMS > rcar-du: probe of feb00000.display failed with error -22 > scsi host0: sata_rcar > ata1: SATA max UDMA/133 irq 110 > renesas_spi e6b10000.spi: DMA available > m25p80 spi0.0: s25fl512s (65536 Kbytes) > 3 ofpart partitions found on MTD device spi0.0 > Creating 3 MTD partitions on "spi0.0": > 0x000000000000-0x000000080000 : "loader" > 0x000000080000-0x000000600000 : "user" > 0x000000600000-0x000004000000 : "flash" > renesas_spi e6b10000.spi: probed > spi_sh_msiof e6e20000.spi: DMA available > libphy: sh_mii: probed > sh-eth ee700000.ethernet eth0: Base address at 0xee700000, 2e:09:0a:00:75:df, IRQ 109. > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > ehci-pci: EHCI PCI platform driver > ehci-pci 0000:00:02.0: enabling device (0140 -> 0142) > ehci-pci 0000:00:02.0: EHCI Host Controller > ehci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1 > ehci-pci 0000:00:02.0: irq 120, io mem 0xee081000 > ehci-pci 0000:00:02.0: USB 2.0 started, EHCI 1.00 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > ehci-pci 0001:01:02.0: enabling device (0140 -> 0142) > ehci-pci 0001:01:02.0: EHCI Host Controller > ehci-pci 0001:01:02.0: new USB bus registered, assigned bus number 2 > ehci-pci 0001:01:02.0: irq 121, io mem 0xee0c1000 > ehci-pci 0001:01:02.0: USB 2.0 started, EHCI 1.00 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > ohci-pci: OHCI PCI platform driver > ohci-pci 0000:00:01.0: enabling device (0140 -> 0142) > ohci-pci 0000:00:01.0: OHCI PCI host controller > ohci-pci 0000:00:01.0: new USB bus registered, assigned bus number 3 > ohci-pci 0000:00:01.0: irq 120, io mem 0xee080000 > ohci-pci 0000:00:01.0: init err (00002edf 0000) > ohci-pci 0000:00:01.0: can't start > ohci-pci 0000:00:01.0: startup error -75 > ohci-pci 0000:00:01.0: USB bus 3 deregistered > ohci-pci 0000:00:01.0: init 0000:00:01.0 fail, -75 > ohci-pci: probe of 0000:00:01.0 failed with error -75 > ohci-pci 0001:01:01.0: enabling device (0140 -> 0142) > ohci-pci 0001:01:01.0: OHCI PCI host controller > ohci-pci 0001:01:01.0: new USB bus registered, assigned bus number 3 > ohci-pci 0001:01:01.0: irq 121, io mem 0xee0c0000 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 1 port detected > sh-pfc e6060000.pfc: pin GP_7_23 already requested by ee090000.pci; cannot claim for e6590000.usb > sh-pfc e6060000.pfc: pin-247 (e6590000.usb) status -22 > sh-pfc e6060000.pfc: could not request pin 247 (GP_7_23) from group usb0 on device sh-pfc > renesas_usbhs e6590000.usb: Error applying setting, reverse things back > renesas_usbhs e6590000.usb: gadget probed > renesas_usbhs e6590000.usb: platform init failed. > renesas_usbhs e6590000.usb: probe failed > mousedev: PS/2 mouse device common for all mice > i2c /dev entries driver > at24 2-0050: 256 byte 24c02 EEPROM, writable, 16 bytes/write > i2c-rcar e6530000.i2c: probed > adv7180 2-0020: chip found @ 0x20 (e6530000.i2c) > ata1: link resume succeeded after 1 retries > soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0 > ------------[ cut here ]------------ > WARNING: CPU: 0 PID: 1 at drivers/base/devres.c:887 devm_kfree+0x30/0x40() > CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc2 #33 > Hardware name: Generic R8A7791 (Flattened Device Tree) > Backtrace: > [] (dump_backtrace) from [] (show_stack+0x18/0x1c) > r7:c058aadd r6:ee82f9c0 r5:00000009 r4:00000000 > [] (show_stack) from [] (dump_stack+0x78/0x94) > [] (dump_stack) from [] (warn_slowpath_common+0x88/0xb4) > r5:00000009 r4:00000000 > [] (warn_slowpath_common) from [] (warn_slowpath_null+0x24/0x2c) > r9:eeb0daa8 r8:eefe0398 r7:eeaaf810 r6:eeaafc20 r5:fffffffa r4:eeb0da90 > [] (warn_slowpath_null) from [] (devm_kfree+0x30/0x40) > [] (devm_kfree) from [] (soc_of_bind.isra.14+0x194/0x1d4) > [] (soc_of_bind.isra.14) from [] (soc_camera_host_register+0x208/0x31c) > r9:00000070 r8:eefe7384 r7:ee960210 r6:00000000 r5:eefe7000 r4:eeaafc20 > [] (soc_camera_host_register) from [] (rcar_vin_probe+0x1f8/0x23c) > r9:00000070 r8:ee960200 r7:00000008 r6:ee960210 r5:eeaafc10 r4:c0635470 > [] (rcar_vin_probe) from [] (platform_drv_probe+0x50/0xa0) > r10:00000000 r9:c063527c r8:00000000 r7:c0664e40 r6:c063527c r5:ee960210 > r4:ffffffef > [] (platform_drv_probe) from [] (driver_probe_device+0xc4/0x208) > r7:c0664e40 r6:c0664e34 r5:00000000 r4:ee960210 > [] (driver_probe_device) from [] (__driver_attach+0x70/0x94) > r9:c0641740 r8:00000000 r7:c062db60 r6:c063527c r5:ee960244 r4:ee960210 > [] (__driver_attach) from [] (bus_for_each_dev+0x74/0x98) > r7:c062db60 r6:c0257028 r5:c063527c r4:00000000 > [] (bus_for_each_dev) from [] (driver_attach+0x20/0x28) > r6:eea25000 r5:00000000 r4:c063527c > [] (driver_attach) from [] (bus_add_driver+0xdc/0x1c4) > [] (bus_add_driver) from [] (driver_register+0xa4/0xe8) > r7:c0600400 r6:c0600400 r5:c05e73a4 r4:c063527c > [] (driver_register) from [] (__platform_driver_register+0x50/0x64) > r5:c05e73a4 r4:ee0d9680 > [] (__platform_driver_register) from [] (rcar_vin_driver_init+0x18/0x20) > [] (rcar_vin_driver_init) from [] (do_one_initcall+0x10c/0x1bc) > [] (do_one_initcall) from [] (kernel_init_freeable+0x118/0x1e0) > r8:c0641740 r7:c0608f60 r6:c0600c2c r5:000000ad r4:00000006 > [] (kernel_init_freeable) from [] (kernel_init+0x14/0xec) > r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c048700c r4:c0641740 > [] (kernel_init) from [] (ret_from_fork+0x14/0x34) > r5:c048700c r4:00000000 > ---[ end trace f0b41a6645a18806 ]--- > rcar_vin e6ef1000.video: group probe failed: -6 > ata1: SATA link down (SStatus 0 SControl 300) > rcar_thermal e61f0000.thermal: 1 sensor probed > Driver 'mmcblk' needs updating - please use bus_type methods > sh_mobile_sdhi ee100000.sd: Got CD GPIO > sh_mobile_sdhi ee100000.sd: Got WP GPIO > platform ee100000.sd: Driver sh_mobile_sdhi requests probe deferral > sh_mobile_sdhi ee140000.sd: Got CD GPIO > sh_mobile_sdhi ee140000.sd: Got WP GPIO > platform ee140000.sd: Driver sh_mobile_sdhi requests probe deferral > sh_mobile_sdhi ee160000.sd: Got CD GPIO > platform ee160000.sd: Driver sh_mobile_sdhi requests probe deferral > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > platform sound: Driver asoc-simple-card requests probe deferral > rcar_sound ec500000.rcar_sound: can't get dma channel > rcar_sound ec500000.rcar_sound: src[2] (Gen2) failed > rcar_sound ec500000.rcar_sound: ssi[0] fallback to PIO mode > rcar_sound ec500000.rcar_sound: can't get dma channel > rcar_sound ec500000.rcar_sound: src[3] (Gen2) failed > rcar_sound ec500000.rcar_sound: ssi[1] fallback to PIO mode > rcar_sound ec500000.rcar_sound: probed > TCP: cubic registered > NET: Registered protocol family 10 > sit: IPv6 over IPv4 tunneling driver > NET: Registered protocol family 17 > Key type dns_resolver registered > Registering SWP/SWPB emulation handler > sh_mobile_sdhi ee100000.sd: Got CD GPIO > sh_mobile_sdhi ee100000.sd: Got WP GPIO > sh_mobile_sdhi ee100000.sd: mmc0 base at 0xee100000 clock rate 97 MHz > sh_mobile_sdhi ee140000.sd: Got CD GPIO > sh_mobile_sdhi ee140000.sd: Got WP GPIO > sh_mobile_sdhi ee140000.sd: mmc1 base at 0xee140000 clock rate 97 MHz > sh_mobile_sdhi ee160000.sd: Got CD GPIO > sh_mobile_sdhi ee160000.sd: mmc2 base at 0xee160000 clock rate 97 MHz > asoc-simple-card sound: ak4642-hifi <-> ec500000.rcar_sound mapping ok > input: keyboard as /devices/platform/keyboard/input/input0 > drivers/rtc/hctosys.c: unable to open rtc device (rtc0) > sh-eth ee700000.ethernet eth0: attached PHY 1 (IRQ 375) to driver Micrel KSZ8041RNLI > Sending DHCP requests .. > sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx > ., OK > IP-Config: Got DHCP answer from 172.16.1.9, my address is 172.16.1.36 > IP-Config: Complete: > device=eth0, hwaddr.:09:0a:00:75:df, ipaddr2.16.1.36, mask%5.255.255.0, gw2.16.1.9 > host2.16.1.36, domain=, nis-domain=(none) > bootserver2.16.1.9, rootserver2.16.1.9, rootpath> nameserver02.16.1.30, nameserver12.16.1.40, nameserver2=8.8.8.8 > SDHI2 VccQ: disabling > SDHI1 VccQ: disabling > SDHI0 VccQ: disabling > SDHI2 Vcc: disabling > SDHI1 Vcc: disabling > SDHI0 Vcc: disabling > ALSA device list: > #0: rsnd-dai.0-ak4642-hifi > VFS: Mounted root (nfs filesystem) on device 0:13. > devtmpfs: mounted > Freeing unused kernel memory: 272K (c05ca000 - c060e000) > Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory > random: init urandom read with 46 bits of entropy available > init: plymouth-upstart-bridge main process (790) terminated with status 1 > init: plymouth-upstart-bridge main process ended, respawning > init: plymouth-upstart-bridge main process (799) terminated with status 1 > init: plymouth-upstart-bridge main process ended, respawning > random: nonblocking pool is initialized > systemd-udevd[888]: starting version 204 > Unable to boot CPU1 when MD21 is set > CPU1: failed to boot: -524 > init: udev-fallback-graphics main process (1404) terminated with status 1 > * Stopping Send an event to indicate plymouth is up[ OK ] > * Starting Mount filesystems on boot[ OK ] > * Starting Signal sysvinit that the rootfs is mounted[ OK ] > * Starting Populate /dev filesystem[ OK ] > * Stopping Populate /dev filesystem[ OK ] > * Starting Clean /tmp directory[ OK ] > * Stopping Clean /tmp directory[ OK ] > * Starting Populate and link to /run filesystem[ OK ] > * Stopping Populate and link to /run filesystem[ OK ] > * Stopping Track if upstart is running in a container[ OK ] > * Starting set console keymap[ OK ] > * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] > * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] > * Starting Bridge udev events into upstart[ OK ] > * Starting Signal sysvinit that local filesystems are mounted[ OK ] > * Starting Signal sysvinit that remote filesystems are mounted[ OK ] > * Starting device node and kernel event manager[ OK ] > * Stopping set console keymap[ OK ] > * Starting flush early job output to logs[ OK ] > * Stopping Mount filesystems on boot[ OK ] > * Stopping flush early job output to logs[ OK ] > * Starting load modules from /etc/modules[ OK ] > * Starting cold plug devices[ OK ] > * Starting log initial device creation[ OK ] > * Stopping load modules from /etc/modules[ OK ] > * Starting system logging daemon[ OK ] > * Stopping cold plug devices[ OK ] > * Stopping log initial device creation[ OK ] > * Starting load fallback graphics devices[ OK ] > * Starting configure network device security[ OK ] > * Starting load fallback graphics devices[fail] > * Starting save udev log and update rules[ OK ] > * Starting set console font[ OK ] > * Stopping set console font[ OK ] > * Starting userspace bootsplash[ OK ] > * Starting configure network device security[ OK ] > * Stopping userspace bootsplash[ OK ] > * Starting Send an event to indicate plymouth is up[ OK ] > * Starting configure network device[ OK ] > * Stopping Send an event to indicate plymouth is up[ OK ] > * Stopping save udev log and update rules[ OK ] > * Starting System V initialisation compatibility[ OK ] > * Starting configure virtual network devices[ OK ] > * Starting configure network device security[ OK ] > * Starting configure network device security[ OK ] > * Stopping System V initialisation compatibility[ OK ] > * Starting configure network device[ OK ] > init: alsa-restore main process (1546) terminated with status 99 > * Starting System V runlevel compatibility[ OK ] > * Starting regular background program processing daemon[ OK ] > * Starting save kernel messages[ OK ] > * Stopping System V runlevel compatibility[ OK ] > init: auto-serial-console main process ended, respawning > * Starting configure network device[ OK ] > * Starting OpenSSH server[ OK ] > init: plymouth-upstart-bridge main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: tty1 main process (1592) killed by TERM signal > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console main process ended, respawning > init: auto-serial-console respawning too fast, stopped > >