From mboxrd@z Thu Jan  1 00:00:00 1970
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Date: Thu, 14 Nov 2013 23:06:47 +0000
Subject: Re: [PATCH v2 2/3] ARM: shmobile: Koelsch: add Ether support
Message-Id: <2664891.LKK7X6OLFJ@avalon>
List-Id: <linux-sh.vger.kernel.org>
References: <201311150217.23563.sergei.shtylyov@cogentembedded.com>
 <201311150221.12125.sergei.shtylyov@cogentembedded.com>
In-Reply-To: <201311150221.12125.sergei.shtylyov@cogentembedded.com>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: linux-arm-kernel@lists.infradead.org

Hi Sergei,

Thank you for the patch.

On Friday 15 November 2013 02:21:11 Sergei Shtylyov wrote:
> Register Ether platform device and pin data on  the  Koelsch board.
> Register platform fixup for Micrel KSZ8041 PHY, just like on the Lager
> board.
> 
> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
> 
> ---
> Changes in version 2:
> - added *if* (IS_ENABLED(CONFIG_PHYLIB)) around phy_register_fixup_for_id()
>   call;
> - changed Ether device name to "r8a779x-ether".
> 
>  arch/arm/mach-shmobile/board-koelsch.c |   63 ++++++++++++++++++++++++++++-
>  1 file changed, 62 insertions(+), 1 deletion(-)
> 
> Index: renesas/arch/arm/mach-shmobile/board-koelsch.c
> =================================> --- renesas.orig/arch/arm/mach-shmobile/board-koelsch.c
> +++ renesas/arch/arm/mach-shmobile/board-koelsch.c
> @@ -24,14 +24,31 @@
>  #include <linux/input.h>
>  #include <linux/kernel.h>
>  #include <linux/leds.h>
> +#include <linux/phy.h>
> +#include <linux/pinctrl/machine.h>
>  #include <linux/platform_data/gpio-rcar.h>
>  #include <linux/platform_device.h>
> +#include <linux/sh_eth.h>
>  #include <mach/common.h>
> +#include <mach/irqs.h>
>  #include <mach/r8a7791.h>
>  #include <mach/rcar-gen2.h>
>  #include <asm/mach-types.h>
>  #include <asm/mach/arch.h>
> 
> +/* Ether */
> +static const struct sh_eth_plat_data ether_pdata __initconst = {
> +	.phy			= 0x1,
> +	.edmac_endian		= EDMAC_LITTLE_ENDIAN,
> +	.phy_interface		= PHY_INTERFACE_MODE_RMII,
> +	.ether_link_active_low	= 1,
> +};
> +
> +static const struct resource ether_resources[] __initconst = {
> +	DEFINE_RES_MEM(0xee700000, 0x400),
> +	DEFINE_RES_IRQ(gic_spi(162)),
> +};
> +
>  /* LEDS */
>  static struct gpio_led koelsch_leds[] = {
>  	{
> @@ -71,11 +88,29 @@ static const struct gpio_keys_platform_d
>  	.nbuttons	= ARRAY_SIZE(gpio_buttons),
>  };
> 
> +static const struct pinctrl_map koelsch_pinctrl_map[] = {
> +	/* Ether */
> +	PIN_MAP_MUX_GROUP_DEFAULT("r8a779x-ether", "pfc-r8a7791",
> +				  "eth_link", "eth"),
> +	PIN_MAP_MUX_GROUP_DEFAULT("r8a779x-ether", "pfc-r8a7791",
> +				  "eth_mdio", "eth"),
> +	PIN_MAP_MUX_GROUP_DEFAULT("r8a779x-ether", "pfc-r8a7791",
> +				  "eth_rmii", "eth"),
> +};
> +
>  static void __init koelsch_add_standard_devices(void)
>  {
>  	r8a7791_clock_init();
> +
> +	pinctrl_register_mappings(koelsch_pinctrl_map,
> +				  ARRAY_SIZE(koelsch_pinctrl_map));
>  	r8a7791_pinmux_init();
> +
>  	r8a7791_add_standard_devices();
> +	platform_device_register_resndata(&platform_bus, "r8a779x-ether", -1,
> +					  ether_resources,
> +					  ARRAY_SIZE(ether_resources),
> +					  &ether_pdata, sizeof(ether_pdata));
>  	platform_device_register_data(&platform_bus, "leds-gpio", -1,
>  				      &koelsch_leds_pdata,
>  				      sizeof(koelsch_leds_pdata));
> @@ -84,6 +119,32 @@ static void __init koelsch_add_standard_
>  				      sizeof(koelsch_keys_pdata));
>  }
> 
> +/*
> + * Ether LEDs on the Koelsch board are named LINK and ACTIVE which
> corresponds + * to non-default 01 setting of the Micrel KSZ8041 PHY control
> register 1 bits + * 14-15. We have to set them back to 01 from the default
> 00 value each time + * the PHY is reset. It's also important because the
> PHY's LED0 signal is + * connected to SoC's ETH_LINK signal and in the
> PHY's default mode it will + * bounce on and off after each packet, which
> we apparently want to avoid. + */
> +static int koelsch_ksz8041_fixup(struct phy_device *phydev)
> +{
> +	u16 phyctrl1 = phy_read(phydev, 0x1e);
> +
> +	phyctrl1 &= ~0xc000;
> +	phyctrl1 |= 0x4000;
> +	return phy_write(phydev, 0x1e, phyctrl1);
> +}
> +
> +static void __init koelsch_init(void)
> +{
> +	koelsch_add_standard_devices();
> +
> +	if (IS_ENABLED(CONFIG_PHYLIB))
> +		phy_register_fixup_for_id("r8a779x-ether-ff:01",
> +					  koelsch_ksz8041_fixup);

This is fine with board code, but will break when we'll switch to DT. Would it 
be difficult to replace board code by using the existing micrel phy driver 
(drivers/net/phy/micrel.c) which should support the ksz8041 already and 
extending it with support for register 0x1e which doesn't seem to be handled ?

> +}
> +
>  static const char * const koelsch_boards_compat_dt[] __initconst = {
>  	"renesas,koelsch",
>  	NULL,
> @@ -92,7 +153,7 @@ static const char * const koelsch_boards
>  DT_MACHINE_START(KOELSCH_DT, "koelsch")
>  	.smp		= smp_ops(r8a7791_smp_ops),
>  	.init_early	= r8a7791_init_early,
> -	.init_machine	= koelsch_add_standard_devices,
> +	.init_machine	= koelsch_init,
>  	.init_time	= rcar_gen2_timer_init,
>  	.dt_compat	= koelsch_boards_compat_dt,
>  MACHINE_END

-- 
Regards,

Laurent Pinchart