From mboxrd@z Thu Jan 1 00:00:00 1970 From: Cao Minh Hiep Date: Tue, 10 Mar 2015 01:53:45 +0000 Subject: Re: Can't boot kernel v4.0-rc2 on Koelsch Message-Id: <54FE4EA9.3070901@jinso.co.jp> List-Id: References: <2263226.JPOqZgiCRj@avalon> In-Reply-To: <2263226.JPOqZgiCRj@avalon> MIME-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 8bit To: linux-sh@vger.kernel.org Hi Simon-san, Cc: Laurent-san, Thank for your comments, On 2015年03月10日 10:14, Simon Horman wrote: > Hi Hiep-san, > > I'd like to agree with Laurent's observation that this appears > to mean that your userspace is broken / needs updating. The boards > in question boot to userspace in my environment. Thanks, I will re-check and update my userspace. By the way, could you please tell me your type of userspace and version that you are using? Thank you. Jinso/Hiep > On Mon, Mar 09, 2015 at 06:43:54PM +0900, Cao Minh Hiep wrote: >> Hi Laurent-san, >> Thanks for your comment, >> >> On 2015年03月09日 16:06, Laurent Pinchart wrote: >>> Hello Hiep-san, >>> >>> On Monday 09 March 2015 10:07:04 Cao Minh Hiep wrote: >>>> Hi Laurent-san >>>> >>>> I am Hiep from Jinzai Solution. >>>> I'm sorry to bother you again! >>> No worries. >>> >>>> We are testing the linux ver v4.0-rc2 on Koelsch, We can not boot the >>>> kernel v4.0-rc2 on Koelsch, >>>> Then we found a patch has changed as below: >>>> "1f75cda ARM: shmobile: koelsch: Rename SCIF[01] serial ports to ttySC[01]" >>>> >>>> Please see it when you have time! >>> Could you please detail your boot failure ? You might need to change your >>> /etc/inittab to adjust to the serial port new name, but apart from that there >>> shouldn't be any issue. I can boot my Koelsch board on 4.0-v2. >> Sure, I use the rootfs of Linaro-nano 2014.09 to test v4.0-rc2. >> When booting kernel with default config, bootlogs showed until these >> messages appearing. >> "init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: tty1 main process (1449) killed by TERM signal >> init: auto-serial-console respawning too fast, stopped" >> >> Then, my Koelsch board stoped here.(my Lager board is the same) >> (I attached the bootlogs_file) >> >> So, When I tried to add "console=ttySC0," into bootargs (at .dts file), i >> can boot my Koelsch board without any problems. >> And these are the same on Lager board. >> >> Thank you! >> Jinso/Hiep >> ====>> information: >> Actually, on v4.0-rc2, we have two patches related each other as below: >> 79e69d1 ARM: shmobile: koelsch dts:Drop console= bootargs parameter BAD. >> 1f75cda ARM: shmobile: koelsch: Rename SCIF01 serial ports to ttySC01 >> >> And for Lager: >> 569dd56 ARM: shmobile: lager dts: Drop console= bootargs parameter >> 78c11ec ARM: shmobile: lager: Rename SCIFA[01] serial ports to ttySC[01] >> >> There is only 79e69d1 patch on v3.19-rcX, I also had a problem with bootting >> Koelsch on v3.19-rcX >> (using linaro-nano 2014.09). But it was good on Yocto and >> linaro-nano-2013.02 >> >> >> >> >> >> => bootp;bootm >> sh_eth Waiting for PHY auto negotiation to complete.. done >> sh_eth: 100Base/Full >> BOOTP broadcast 1 >> DHCP client bound to address 172.16.1.36 >> Using sh_eth device >> TFTP from server 172.16.1.9; our IP address is 172.16.1.36 >> Filename 'Koelsch/uImage.dtb'. >> Load address: 0x40007fc0 >> Loading: #######################������������������������������������������������������������������������������������0 >> Linux version 4.0.0-rc2 (jinso02@jinso02) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-25 >> CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), crc5307d >> CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache >> Machine model: Koelsch >> Ignoring memory block 0x200000000 - 0x240000000 >> debug: ignoring loglevel setting. >> Memory policy: Data cache writealloc >> On node 0 totalpages: 262144 >> free_area_init_node: node 0, pgdat c063fe00, node_mem_map eeff9000 >> Normal zone: 1520 pages used for memmap >> Normal zone: 0 pages reserved >> Normal zone: 194560 pages, LIFO batch:31 >> HighMem zone: 67584 pages, LIFO batch:15 >> PERCPU: Embedded 8 pages/cpu @eefca000 s11456 r0 d21312 u32768 >> pcpu-alloc: s11456 r0 d21312 u32768 alloc=8*4096 >> pcpu-alloc: [0] 0 [0] 1 >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624 >> Kernel command line: ignore_loglevel rw root=/dev/nfs ip=dhcp >> PID hash table entries: 4096 (order: 2, 16384 bytes) >> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) >> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) >> Memory: 1032772K/1048576K available (4636K kernel code, 205K rwdata, 1252K rodata, 272K init, 192K bss, 15804K reser) >> Virtual kernel memory layout: >> vector : 0xffff0000 - 0xffff1000 ( 4 kB) >> fixmap : 0xffc00000 - 0xfff00000 (3072 kB) >> vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) >> lowmem : 0xc0000000 - 0xef800000 ( 760 MB) >> pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) >> .text : 0xc0008000 - 0xc05c9044 (5893 kB) >> .init : 0xc05ca000 - 0xc060e000 ( 272 kB) >> .data : 0xc060e000 - 0xc0641720 ( 206 kB) >> .bss : 0xc0641720 - 0xc06717ec ( 193 kB) >> Hierarchical RCU implementation. >> Additional per-CPU info printed with stalls. >> RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. >> RCU: Adjusting geometry for rcu_fanout_leaf, nr_cpu_ids=2 >> NR_IRQS:16 nr_irqs:16 16 >> Architected cp15 timer(s) running at 10.00MHz (virt). >> sched_clock: 56 bits at 10MHz, resolution 100ns, wraps every 3435973836800ns >> Switching to timer-based delay loop, resolution 100ns >> Console: colour dummy device 80x30 >> console [tty0] enabled >> Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj0000) >> pid_max: default: 32768 minimum: 301 >> Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) >> Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) >> CPU: Testing write buffer coherency: ok >> CPU0: update cpu_capacity 1024 >> CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 >> Setting up static identity map for 0x4048dba0 - 0x4048dbf8 >> Unable to boot CPU1 when MD21 is set >> CPU1: failed to boot: -524 >> Brought up 1 CPUs >> SMP: Total of 1 processors activated (20.00 BogoMIPS). >> CPU: All CPU(s) started in SVC mode. >> devtmpfs: initialized >> VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 >> pinctrl core: initialized pinctrl subsystem >> NET: Registered protocol family 16 >> DMA: preallocated 256 KiB pool for atomic coherent allocations >> renesas_irqc e61c0000.interrupt-controller: driving 10 irqs >> sh-pfc e6060000.pfc: r8a77910_pfc support registered >> No ATAGs? >> hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. >> hw-breakpoint: maximum watchpoint size is 8 bytes. >> platform regulator@0: Driver reg-fixed-voltage requests probe deferral >> platform regulator@2: Driver reg-fixed-voltage requests probe deferral >> platform regulator@4: Driver reg-fixed-voltage requests probe deferral >> gpio-regulator regulator@1: Could not obtain regulator setting GPIOs: -517 >> platform regulator@1: Driver gpio-regulator requests probe deferral >> gpio-regulator regulator@3: Could not obtain regulator setting GPIOs: -517 >> platform regulator@3: Driver gpio-regulator requests probe deferral >> gpio-regulator regulator@5: Could not obtain regulator setting GPIOs: -517 >> platform regulator@5: Driver gpio-regulator requests probe deferral >> vgaarb: loaded >> SCSI subsystem initialized >> libata version 3.00 loaded. >> usbcore: registered new interface driver usbfs >> usbcore: registered new interface driver hub >> usbcore: registered new device driver usb >> i2c-sh_mobile e60b0000.i2c: I2C adapter 6, bus speed 100000 Hz >> media: Linux media interface: v0.10 >> Linux video capture interface: v2.00 >> sh_cmt ffca0000.timer: ch0: used for clock events >> sh_cmt ffca0000.timer: ch1: used as clock source >> Advanced Linux Sound Architecture Driver Initialized. >> Switched to clocksource arch_sys_counter >> NET: Registered protocol family 2 >> TCP established hash table entries: 8192 (order: 3, 32768 bytes) >> TCP bind hash table entries: 8192 (order: 4, 65536 bytes) >> TCP: Hash tables configured (established 8192 bind 8192) >> TCP: reno registered >> UDP hash table entries: 512 (order: 2, 16384 bytes) >> UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) >> NET: Registered protocol family 1 >> RPC: Registered named UNIX socket transport module. >> RPC: Registered udp transport module. >> RPC: Registered tcp transport module. >> RPC: Registered tcp NFSv4.1 backchannel transport module. >> PCI: CLS 0 bytes, default 64 >> futex hash table entries: 512 (order: 3, 32768 bytes) >> NFS: Registering the id_resolver key type >> Key type id_resolver registered >> Key type id_legacy registered >> nfs4filelayout_init: NFSv4 File Layout Driver Registering... >> nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... >> bounce: pool size: 64 pages >> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) >> io scheduler noop registered >> io scheduler deadline registered >> io scheduler cfq registered (default) >> gpio_rcar e6050000.gpio: driving 32 GPIOs >> gpio_rcar e6051000.gpio: driving 32 GPIOs >> gpio_rcar e6052000.gpio: driving 32 GPIOs >> gpio_rcar e6053000.gpio: driving 32 GPIOs >> gpio_rcar e6054000.gpio: driving 32 GPIOs >> gpio_rcar e6055000.gpio: driving 32 GPIOs >> gpio_rcar e6055400.gpio: driving 32 GPIOs >> gpio_rcar e6055800.gpio: driving 26 GPIOs >> pci-rcar-gen2 ee090000.pci: PCI: bus0 revision 11 >> pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00 >> pci_bus 0000:00: root bus resource [io 0xee080000-0xee0810ff] >> pci_bus 0000:00: root bus resource [mem 0xee080000-0xee0810ff] >> pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] >> pci 0000:00:00.0: [1033:0000] type 00 class 0x060000 >> pci 0000:00:00.0: reg 0x10: [mem 0xee090800-0xee090bff] >> pci 0000:00:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref] >> pci 0000:00:01.0: [1033:0035] type 00 class 0x0c0310 >> pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00000fff] >> pci 0000:00:01.0: supports D1 D2 >> pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot >> pci 0000:00:02.0: [1033:00e0] type 00 class 0x0c0320 >> pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x000000ff] >> pci 0000:00:02.0: supports D1 D2 >> pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot >> PCI: bus0: Fast back to back transfers disabled >> pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 >> pci 0000:00:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed >> pci 0000:00:01.0: Can't enable PCI device, BIOS handoff failed. >> pci 0000:00:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed >> pci 0000:00:02.0: Can't enable PCI device, BIOS handoff failed. >> pci 0000:00:01.0: BAR 0: assigned [mem 0xee080000-0xee080fff] >> pci 0000:00:02.0: BAR 0: assigned [mem 0xee081000-0xee0810ff] >> pci-rcar-gen2 ee0d0000.pci: PCI: bus0 revision 11 >> pci-rcar-gen2 ee0d0000.pci: PCI host bridge to bus 0001:01 >> pci_bus 0001:01: root bus resource [io 0xee0c0000-0xee0c10ff] >> pci_bus 0001:01: root bus resource [mem 0xee0c0000-0xee0c10ff] >> pci_bus 0001:01: No busn resource found for root bus, will use [bus 01-ff] >> pci 0001:01:00.0: [1033:0000] type 00 class 0x060000 >> pci 0001:01:00.0: reg 0x10: [mem 0xee0d0800-0xee0d0bff] >> pci 0001:01:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref] >> pci 0001:01:01.0: [1033:0035] type 00 class 0x0c0310 >> pci 0001:01:01.0: reg 0x10: [mem 0x00000000-0x00000fff] >> pci 0001:01:01.0: supports D1 D2 >> pci 0001:01:01.0: PME# supported from D0 D1 D2 D3hot >> pci 0001:01:02.0: [1033:00e0] type 00 class 0x0c0320 >> pci 0001:01:02.0: reg 0x10: [mem 0x00000000-0x000000ff] >> pci 0001:01:02.0: supports D1 D2 >> pci 0001:01:02.0: PME# supported from D0 D1 D2 D3hot >> PCI: bus1: Fast back to back transfers disabled >> pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 >> pci 0001:01:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed >> pci 0001:01:01.0: Can't enable PCI device, BIOS handoff failed. >> pci 0001:01:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed >> pci 0001:01:02.0: Can't enable PCI device, BIOS handoff failed. >> pci 0001:01:01.0: BAR 0: assigned [mem 0xee0c0000-0xee0c0fff] >> pci 0001:01:02.0: BAR 0: assigned [mem 0xee0c1000-0xee0c10ff] >> rcar-pcie fe000000.pcie: PCIe link down >> Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled >> SuperH (H)SCI(F) driver initialized >> e6e60000.serial: ttySC0 at MMIO 0xe6e60000 (irq = 107, base_baud = 0) is a scif >> console [ttySC0] enabled >> e6e68000.serial: ttySC1 at MMIO 0xe6e68000 (irq = 108, base_baud = 0) is a scif >> [drm] Initialized drm 1.1.0 20060810 >> rcar-du feb00000.display: error: no encoder could be initialized >> rcar-du feb00000.display: failed to initialize DRM/KMS >> rcar-du: probe of feb00000.display failed with error -22 >> scsi host0: sata_rcar >> ata1: SATA max UDMA/133 irq 110 >> renesas_spi e6b10000.spi: DMA available >> m25p80 spi0.0: s25fl512s (65536 Kbytes) >> 3 ofpart partitions found on MTD device spi0.0 >> Creating 3 MTD partitions on "spi0.0": >> 0x000000000000-0x000000080000 : "loader" >> 0x000000080000-0x000000600000 : "user" >> 0x000000600000-0x000004000000 : "flash" >> renesas_spi e6b10000.spi: probed >> spi_sh_msiof e6e20000.spi: DMA available >> libphy: sh_mii: probed >> sh-eth ee700000.ethernet eth0: Base address at 0xee700000, 2e:09:0a:00:75:df, IRQ 109. >> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> ehci-pci: EHCI PCI platform driver >> ehci-pci 0000:00:02.0: enabling device (0140 -> 0142) >> ehci-pci 0000:00:02.0: EHCI Host Controller >> ehci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1 >> ehci-pci 0000:00:02.0: irq 120, io mem 0xee081000 >> ehci-pci 0000:00:02.0: USB 2.0 started, EHCI 1.00 >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 1 port detected >> ehci-pci 0001:01:02.0: enabling device (0140 -> 0142) >> ehci-pci 0001:01:02.0: EHCI Host Controller >> ehci-pci 0001:01:02.0: new USB bus registered, assigned bus number 2 >> ehci-pci 0001:01:02.0: irq 121, io mem 0xee0c1000 >> ehci-pci 0001:01:02.0: USB 2.0 started, EHCI 1.00 >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 1 port detected >> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver >> ohci-pci: OHCI PCI platform driver >> ohci-pci 0000:00:01.0: enabling device (0140 -> 0142) >> ohci-pci 0000:00:01.0: OHCI PCI host controller >> ohci-pci 0000:00:01.0: new USB bus registered, assigned bus number 3 >> ohci-pci 0000:00:01.0: irq 120, io mem 0xee080000 >> ohci-pci 0000:00:01.0: init err (00002edf 0000) >> ohci-pci 0000:00:01.0: can't start >> ohci-pci 0000:00:01.0: startup error -75 >> ohci-pci 0000:00:01.0: USB bus 3 deregistered >> ohci-pci 0000:00:01.0: init 0000:00:01.0 fail, -75 >> ohci-pci: probe of 0000:00:01.0 failed with error -75 >> ohci-pci 0001:01:01.0: enabling device (0140 -> 0142) >> ohci-pci 0001:01:01.0: OHCI PCI host controller >> ohci-pci 0001:01:01.0: new USB bus registered, assigned bus number 3 >> ohci-pci 0001:01:01.0: irq 121, io mem 0xee0c0000 >> hub 3-0:1.0: USB hub found >> hub 3-0:1.0: 1 port detected >> sh-pfc e6060000.pfc: pin GP_7_23 already requested by ee090000.pci; cannot claim for e6590000.usb >> sh-pfc e6060000.pfc: pin-247 (e6590000.usb) status -22 >> sh-pfc e6060000.pfc: could not request pin 247 (GP_7_23) from group usb0 on device sh-pfc >> renesas_usbhs e6590000.usb: Error applying setting, reverse things back >> renesas_usbhs e6590000.usb: gadget probed >> renesas_usbhs e6590000.usb: platform init failed. >> renesas_usbhs e6590000.usb: probe failed >> mousedev: PS/2 mouse device common for all mice >> i2c /dev entries driver >> at24 2-0050: 256 byte 24c02 EEPROM, writable, 16 bytes/write >> i2c-rcar e6530000.i2c: probed >> adv7180 2-0020: chip found @ 0x20 (e6530000.i2c) >> ata1: link resume succeeded after 1 retries >> soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0 >> ------------[ cut here ]------------ >> WARNING: CPU: 0 PID: 1 at drivers/base/devres.c:887 devm_kfree+0x30/0x40() >> CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc2 #33 >> Hardware name: Generic R8A7791 (Flattened Device Tree) >> Backtrace: >> [] (dump_backtrace) from [] (show_stack+0x18/0x1c) >> r7:c058aadd r6:ee82f9c0 r5:00000009 r4:00000000 >> [] (show_stack) from [] (dump_stack+0x78/0x94) >> [] (dump_stack) from [] (warn_slowpath_common+0x88/0xb4) >> r5:00000009 r4:00000000 >> [] (warn_slowpath_common) from [] (warn_slowpath_null+0x24/0x2c) >> r9:eeb0daa8 r8:eefe0398 r7:eeaaf810 r6:eeaafc20 r5:fffffffa r4:eeb0da90 >> [] (warn_slowpath_null) from [] (devm_kfree+0x30/0x40) >> [] (devm_kfree) from [] (soc_of_bind.isra.14+0x194/0x1d4) >> [] (soc_of_bind.isra.14) from [] (soc_camera_host_register+0x208/0x31c) >> r9:00000070 r8:eefe7384 r7:ee960210 r6:00000000 r5:eefe7000 r4:eeaafc20 >> [] (soc_camera_host_register) from [] (rcar_vin_probe+0x1f8/0x23c) >> r9:00000070 r8:ee960200 r7:00000008 r6:ee960210 r5:eeaafc10 r4:c0635470 >> [] (rcar_vin_probe) from [] (platform_drv_probe+0x50/0xa0) >> r10:00000000 r9:c063527c r8:00000000 r7:c0664e40 r6:c063527c r5:ee960210 >> r4:ffffffef >> [] (platform_drv_probe) from [] (driver_probe_device+0xc4/0x208) >> r7:c0664e40 r6:c0664e34 r5:00000000 r4:ee960210 >> [] (driver_probe_device) from [] (__driver_attach+0x70/0x94) >> r9:c0641740 r8:00000000 r7:c062db60 r6:c063527c r5:ee960244 r4:ee960210 >> [] (__driver_attach) from [] (bus_for_each_dev+0x74/0x98) >> r7:c062db60 r6:c0257028 r5:c063527c r4:00000000 >> [] (bus_for_each_dev) from [] (driver_attach+0x20/0x28) >> r6:eea25000 r5:00000000 r4:c063527c >> [] (driver_attach) from [] (bus_add_driver+0xdc/0x1c4) >> [] (bus_add_driver) from [] (driver_register+0xa4/0xe8) >> r7:c0600400 r6:c0600400 r5:c05e73a4 r4:c063527c >> [] (driver_register) from [] (__platform_driver_register+0x50/0x64) >> r5:c05e73a4 r4:ee0d9680 >> [] (__platform_driver_register) from [] (rcar_vin_driver_init+0x18/0x20) >> [] (rcar_vin_driver_init) from [] (do_one_initcall+0x10c/0x1bc) >> [] (do_one_initcall) from [] (kernel_init_freeable+0x118/0x1e0) >> r8:c0641740 r7:c0608f60 r6:c0600c2c r5:000000ad r4:00000006 >> [] (kernel_init_freeable) from [] (kernel_init+0x14/0xec) >> r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c048700c r4:c0641740 >> [] (kernel_init) from [] (ret_from_fork+0x14/0x34) >> r5:c048700c r4:00000000 >> ---[ end trace f0b41a6645a18806 ]--- >> rcar_vin e6ef1000.video: group probe failed: -6 >> ata1: SATA link down (SStatus 0 SControl 300) >> rcar_thermal e61f0000.thermal: 1 sensor probed >> Driver 'mmcblk' needs updating - please use bus_type methods >> sh_mobile_sdhi ee100000.sd: Got CD GPIO >> sh_mobile_sdhi ee100000.sd: Got WP GPIO >> platform ee100000.sd: Driver sh_mobile_sdhi requests probe deferral >> sh_mobile_sdhi ee140000.sd: Got CD GPIO >> sh_mobile_sdhi ee140000.sd: Got WP GPIO >> platform ee140000.sd: Driver sh_mobile_sdhi requests probe deferral >> sh_mobile_sdhi ee160000.sd: Got CD GPIO >> platform ee160000.sd: Driver sh_mobile_sdhi requests probe deferral >> usbcore: registered new interface driver usbhid >> usbhid: USB HID core driver >> platform sound: Driver asoc-simple-card requests probe deferral >> rcar_sound ec500000.rcar_sound: can't get dma channel >> rcar_sound ec500000.rcar_sound: src[2] (Gen2) failed >> rcar_sound ec500000.rcar_sound: ssi[0] fallback to PIO mode >> rcar_sound ec500000.rcar_sound: can't get dma channel >> rcar_sound ec500000.rcar_sound: src[3] (Gen2) failed >> rcar_sound ec500000.rcar_sound: ssi[1] fallback to PIO mode >> rcar_sound ec500000.rcar_sound: probed >> TCP: cubic registered >> NET: Registered protocol family 10 >> sit: IPv6 over IPv4 tunneling driver >> NET: Registered protocol family 17 >> Key type dns_resolver registered >> Registering SWP/SWPB emulation handler >> sh_mobile_sdhi ee100000.sd: Got CD GPIO >> sh_mobile_sdhi ee100000.sd: Got WP GPIO >> sh_mobile_sdhi ee100000.sd: mmc0 base at 0xee100000 clock rate 97 MHz >> sh_mobile_sdhi ee140000.sd: Got CD GPIO >> sh_mobile_sdhi ee140000.sd: Got WP GPIO >> sh_mobile_sdhi ee140000.sd: mmc1 base at 0xee140000 clock rate 97 MHz >> sh_mobile_sdhi ee160000.sd: Got CD GPIO >> sh_mobile_sdhi ee160000.sd: mmc2 base at 0xee160000 clock rate 97 MHz >> asoc-simple-card sound: ak4642-hifi <-> ec500000.rcar_sound mapping ok >> input: keyboard as /devices/platform/keyboard/input/input0 >> drivers/rtc/hctosys.c: unable to open rtc device (rtc0) >> sh-eth ee700000.ethernet eth0: attached PHY 1 (IRQ 375) to driver Micrel KSZ8041RNLI >> Sending DHCP requests .. >> sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx >> ., OK >> IP-Config: Got DHCP answer from 172.16.1.9, my address is 172.16.1.36 >> IP-Config: Complete: >> device=eth0, hwaddr.:09:0a:00:75:df, ipaddr2.16.1.36, mask%5.255.255.0, gw2.16.1.9 >> host2.16.1.36, domain=, nis-domain=(none) >> bootserver2.16.1.9, rootserver2.16.1.9, rootpath>> nameserver02.16.1.30, nameserver12.16.1.40, nameserver2=8.8.8.8 >> SDHI2 VccQ: disabling >> SDHI1 VccQ: disabling >> SDHI0 VccQ: disabling >> SDHI2 Vcc: disabling >> SDHI1 Vcc: disabling >> SDHI0 Vcc: disabling >> ALSA device list: >> #0: rsnd-dai.0-ak4642-hifi >> VFS: Mounted root (nfs filesystem) on device 0:13. >> devtmpfs: mounted >> Freeing unused kernel memory: 272K (c05ca000 - c060e000) >> Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory >> random: init urandom read with 46 bits of entropy available >> init: plymouth-upstart-bridge main process (790) terminated with status 1 >> init: plymouth-upstart-bridge main process ended, respawning >> init: plymouth-upstart-bridge main process (799) terminated with status 1 >> init: plymouth-upstart-bridge main process ended, respawning >> random: nonblocking pool is initialized >> systemd-udevd[888]: starting version 204 >> Unable to boot CPU1 when MD21 is set >> CPU1: failed to boot: -524 >> init: udev-fallback-graphics main process (1404) terminated with status 1 >> * Stopping Send an event to indicate plymouth is up[ OK ] >> * Starting Mount filesystems on boot[ OK ] >> * Starting Signal sysvinit that the rootfs is mounted[ OK ] >> * Starting Populate /dev filesystem[ OK ] >> * Stopping Populate /dev filesystem[ OK ] >> * Starting Clean /tmp directory[ OK ] >> * Stopping Clean /tmp directory[ OK ] >> * Starting Populate and link to /run filesystem[ OK ] >> * Stopping Populate and link to /run filesystem[ OK ] >> * Stopping Track if upstart is running in a container[ OK ] >> * Starting set console keymap[ OK ] >> * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] >> * Starting Signal sysvinit that virtual filesystems are mounted[ OK ] >> * Starting Bridge udev events into upstart[ OK ] >> * Starting Signal sysvinit that local filesystems are mounted[ OK ] >> * Starting Signal sysvinit that remote filesystems are mounted[ OK ] >> * Starting device node and kernel event manager[ OK ] >> * Stopping set console keymap[ OK ] >> * Starting flush early job output to logs[ OK ] >> * Stopping Mount filesystems on boot[ OK ] >> * Stopping flush early job output to logs[ OK ] >> * Starting load modules from /etc/modules[ OK ] >> * Starting cold plug devices[ OK ] >> * Starting log initial device creation[ OK ] >> * Stopping load modules from /etc/modules[ OK ] >> * Starting system logging daemon[ OK ] >> * Stopping cold plug devices[ OK ] >> * Stopping log initial device creation[ OK ] >> * Starting load fallback graphics devices[ OK ] >> * Starting configure network device security[ OK ] >> * Starting load fallback graphics devices[fail] >> * Starting save udev log and update rules[ OK ] >> * Starting set console font[ OK ] >> * Stopping set console font[ OK ] >> * Starting userspace bootsplash[ OK ] >> * Starting configure network device security[ OK ] >> * Stopping userspace bootsplash[ OK ] >> * Starting Send an event to indicate plymouth is up[ OK ] >> * Starting configure network device[ OK ] >> * Stopping Send an event to indicate plymouth is up[ OK ] >> * Stopping save udev log and update rules[ OK ] >> * Starting System V initialisation compatibility[ OK ] >> * Starting configure virtual network devices[ OK ] >> * Starting configure network device security[ OK ] >> * Starting configure network device security[ OK ] >> * Stopping System V initialisation compatibility[ OK ] >> * Starting configure network device[ OK ] >> init: alsa-restore main process (1546) terminated with status 99 >> * Starting System V runlevel compatibility[ OK ] >> * Starting regular background program processing daemon[ OK ] >> * Starting save kernel messages[ OK ] >> * Stopping System V runlevel compatibility[ OK ] >> init: auto-serial-console main process ended, respawning >> * Starting configure network device[ OK ] >> * Starting OpenSSH server[ OK ] >> init: plymouth-upstart-bridge main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: tty1 main process (1592) killed by TERM signal >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console main process ended, respawning >> init: auto-serial-console respawning too fast, stopped >> >> > -- > To unsubscribe from this list: send the line "unsubscribe linux-sh" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > >