From mboxrd@z Thu Jan 1 00:00:00 1970 From: hermann =?iso-8859-15?q?=F6lberg?= Subject: Fwd: dmesg / MS-6380E ATX mainboard Date: Thu, 30 Jan 2003 10:47:36 +0100 Sender: linux-smp-owner@vger.kernel.org Message-ID: <200301301047.36995.oelberg@aon.at> Mime-Version: 1.0 Content-Type: Multipart/Mixed; boundary="------------Boundary-00=_CVTI552WWYEHVP9OYWID" Return-path: List-Id: To: linux-smp@vger.kernel.org --------------Boundary-00=_CVTI552WWYEHVP9OYWID Content-Type: text/plain; charset="iso-8859-15" Content-Transfer-Encoding: quoted-printable Hallo! Based on "unexpected IO-APIC, please mail to linux-smp...", I send you th= e dmesg as attachement. I'm using a MSI MS-6380E ATX mainbord. regards hermann -- mailto:oelberg@aon.at hermann =F6lberg bahnhofstr.41 6176 v=F6ls 0699-111-53930 --------------Boundary-00=_CVTI552WWYEHVP9OYWID Content-Type: text/plain; charset="iso-8859-15"; name="dmesg" Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="dmesg" Linux version 2.4.20 (root@server) (gcc version 3.2) #13 Sun Jan 26 20:27:48 CET 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data) BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000fb940 hm, page 000fb000 reserved twice. hm, page 000fc000 reserved twice. hm, page 000f6000 reserved twice. hm, page 000f7000 reserved twice. On node 0 totalpages: 262128 zone(0): 4096 pages. zone(1): 225280 pages. zone(2): 32752 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000 Processor #0 Pentium(tm) Pro APIC version 17 I/O APIC #2 Version 3 at 0xFEC00000. Processors: 1 Kernel command line: root=/dev/hda3 enableapic hdc=ide-cd hdd=ide-scsi vga=0x0317 ide_setup: hdc=ide-cd ide_setup: hdd=ide-scsi Initializing CPU#0 Detected 1666.789 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 3322.67 BogoMIPS Memory: 1032904k/1048512k available (1765k kernel code, 15220k reserved, 566k data, 132k init, 131008k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000 CPU: AMD Athlon(tm) XP 2000+ stepping 02 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000080 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-5, 2-11, 2-18, 2-19, 2-20, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 21. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 WARNING: unexpected IO-APIC, please mail to linux-smp@vger.kernel.org .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 001 01 0 0 0 0 0 1 1 51 07 001 01 0 0 0 0 0 1 1 59 08 001 01 0 0 0 0 0 1 1 61 09 001 01 0 0 0 0 0 1 1 69 0a 001 01 0 0 0 0 0 1 1 71 0b 000 00 1 0 0 0 0 0 0 00 0c 001 01 0 0 0 0 0 1 1 79 0d 001 01 0 0 0 0 0 1 1 81 0e 001 01 0 0 0 0 0 1 1 89 0f 001 01 0 0 0 0 0 1 1 91 10 001 01 1 1 0 1 0 1 1 99 11 001 01 1 1 0 1 0 1 1 A1 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 001 01 1 1 0 1 0 1 1 A9 16 001 01 1 1 0 1 0 1 1 B1 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ21 -> 0:21 IRQ22 -> 0:22 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1666.7724 MHz. ..... host bus clock speed is 266.6836 MHz. cpu: 0, clocks: 2666836, slice: 1333418 CPU0 mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Using IRQ router default [1106/3177] at 00:11.0 PCI->APIC IRQ transform: (B0,I6,P0) -> 17 PCI->APIC IRQ transform: (B0,I16,P0) -> 21 PCI->APIC IRQ transform: (B0,I16,P3) -> 21 PCI->APIC IRQ transform: (B0,I17,P0) -> 16 PCI->APIC IRQ transform: (B0,I17,P2) -> 22 PCI->APIC IRQ transform: (B0,I17,P2) -> 22 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 PCI: Via IRQ fixup for 00:11.6, from 5 to 6 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Starting kswapd allocated 32 pages and 32 bhs reserved for the highmem bounces VFS: Diskquotas version dquot_6.4.0 initialized Journalled Block Device driver loaded Installing knfsd (copyright (C) 1996 okir@monad.swb.de). parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected parport0: Printer, Lexmark International Lexmark Optra LaserPrinter vesafb: framebuffer at 0xd0000000, mapped to 0xf880d000, size 8192k vesafb: mode is 1024x768x16, linelength=2048, pages=4 vesafb: protected mode interface info at c000:7442 vesafb: scrolling: redraw vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A lp0: using parport0 (polling). lp0: console ready Real Time Clock Driver v1.10e Non-volatile memory driver v1.2 Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 89 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA hda: IC35L120AVVA07-0, ATA DISK drive hdb: ST360021A, ATA DISK drive hdc: LTN526S, ATAPI CD/DVD-ROM drive hdd: PLEXTOR CD-R PX-W4012A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 blk: queue c039d4c4, I/O limit 4095Mb (mask 0xffffffff) hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=15017/255/63, UDMA(100) blk: queue c039d600, I/O limit 4095Mb (mask 0xffffffff) hdb: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100) Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 > hdb: hdb1 hdb2 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 941M agpgart: Detected Via Apollo Pro KT266 chipset agpgart: AGP aperture is 16M @ 0xe0000000 SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: PLEXTOR Model: CD-R PX-W4012A Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 usb.c: registered new driver usbdevfs usb.c: registered new driver hub NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 138k freed VFS: Mounted root (ext2 filesystem). reiserfs: checking transaction log (device 03:03) ... Using r5 hash to sort names ReiserFS version 3.6.25 VFS: Mounted root (reiserfs filesystem) readonly. Trying to move old root to /initrd ... failed Unmounting old root Trying to free ramdisk memory ... okay Freeing unused kernel memory: 132k freed Adding Swap: 128480k swap-space (priority 42) Adding Swap: 128480k swap-space (priority 42) reiserfs: checking transaction log (device 03:06) ... Using r5 hash to sort names ReiserFS version 3.6.25 reiserfs: checking transaction log (device 03:05) ... Using r5 hash to sort names ReiserFS version 3.6.25 reiserfs: checking transaction log (device 03:07) ... Using r5 hash to sort names ReiserFS version 3.6.25 8139too Fast Ethernet driver 0.9.26 eth0: RealTek RTL8139 Fast Ethernet at 0xec00, 00:02:44:52:04:49, IRQ 17 eth0: Identified 8139 chip type 'RTL-8139C' eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1. ehci-hcd.c: 2002-May-07 USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-hcd.c: block sizes: qh 96 qtd 96 itd 128 sitd 64 hcd.c: ehci-hcd @ 00:10.3, VIA Technologies, Inc. USB 2.0 hcd.c: irq 21, pci mem f9308e00 usb.c: new USB bus registered, assigned bus number 1 ehci-dbg.c: ehci_start hcs_params 0x1202 dbg=0 cc=1 pcc=2 ordered !ppc ports=2 ehci-dbg.c: ehci_start extended capabilities at pci 104 ehci-dbg.c: ehci_start hcc_params 0x6872 caching 7 uframes 256/512/1024 ehci-hcd.c: reset 80002 cmd (park)=0 ithresh=8 period=1024 Reset HALT ehci-hcd.c: init 10001 cmd (park)=0 ithresh=1 period=1024 RUN ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0 hcd.c: 00:10.3 root hub device address 1 usb.c: kmalloc IF f76a3580, numif 1 usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1 usb.c: USB device number 1 default language ID 0x0 Manufacturer: Linux 2.4.20 ehci-hcd Product: VIA Technologies, Inc. USB 2.0 SerialNumber: 00:10.3 hub.c: USB hub found hub.c: 2 ports detected hub.c: standalone hub hub.c: ganged power switching hub.c: individual port over-current protection hub.c: Single TT hub.c: TT requires at most 8 FS bit times hub.c: Port indicators are not supported hub.c: power on to power good time: 0ms hub.c: hub controller current requirement: 0mA hub.c: port removable status: RR hub.c: local power source is good hub.c: no over-current condition exists hub.c: enabling power on all ports usb.c: hub driver claimed interface f76a3580 usb.c: kusbd: /sbin/hotplug add 1 usb-uhci.c: $Revision: 1.275 $ time 20:32:54 Jan 26 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 21 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 usb.c: kmalloc IF f76a37c0, numif 1 usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1 usb.c: USB device number 1 default language ID 0x0 Product: USB UHCI Root Hub SerialNumber: e800 hub.c: USB hub found hub.c: 2 ports detected hub.c: standalone hub hub.c: ganged power switching hub.c: global over-current protection hub.c: Port indicators are not supported hub.c: power on to power good time: 2ms hub.c: hub controller current requirement: 0mA hub.c: port removable status: RR hub.c: local power source is good hub.c: no over-current condition exists hub.c: enabling power on all ports usb.c: hub driver claimed interface f76a37c0 usb.c: kusbd: /sbin/hotplug add 1 usb-uhci.c: v1.275:USB Universal Host Controller Interface driver hub.c: port 1, portstatus 100, change 3, 12 Mb/s hub.c: port 1 connection change hub.c: port 1, portstatus 100, change 3, 12 Mb/s hub.c: port 2, portstatus 100, change 3, 12 Mb/s hub.c: port 2 connection change hub.c: port 2, portstatus 100, change 3, 12 Mb/s uhci.c: USB Universal Host Controller Interface driver v1.1 hub.c: port 1, portstatus 100, change 2, 12 Mb/s hub.c: port 1 enable change, status 100 hub.c: port 2, portstatus 100, change 2, 12 Mb/s hub.c: port 2 enable change, status 100 hdc: bad special flag: 0x03 hdc: ATAPI 52X CD-ROM drive, 120kB Cache, UDMA(33) cdrom: open failed. cdrom: open failed. cdrom: open failed. cdrom: open failed. EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended floppy0: disk absent or changed during operation end_request: I/O error, dev 02:00 (floppy), sector 2 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended --------------Boundary-00=_CVTI552WWYEHVP9OYWID--