From: ray@redshift.com
To: linux-smp@vger.kernel.org
Subject: (unknown)
Subject:
Date: Sun, 15 Dec 2002 17:15:10 -0800 [thread overview]
Message-ID: <3.0.1.32.20021215171510.006d0b0c@pop.redshift.com> (raw)
1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#2.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU2: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
Booting processor 3/7 eip 2000
Initializing CPU#3
masked ExtINT on CPU#3
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4784.26 BogoMIPS
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#3.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU3: Intel(R) XEON(TM) CPU 2.40GHz stepping 04
Total of 4 processors activated (19103.65 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
cpu_sibling_map[2] = 3
cpu_sibling_map[3] = 2
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
Setting 4 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 4 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-17, 2-20, 2-23, 3-0, 3-1, 3-2,
3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 3-16,
3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23, 4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-7,
4-8, 4-9, 4-10, 4-11, 4-12, 4-13, 4-14, 4-15, 4-16, 4-17, 4-18, 4-19, 4-20,
4-21, 4-22, 4-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 24.
number of IO-APIC #4 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02008000
....... : physical APIC id: 02
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 00F 0F 0 0 0 0 0 1 1 39
02 008 08 0 0 0 0 0 1 1 31
03 00F 0F 0 0 0 0 0 1 1 41
04 00F 0F 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 00F 0F 0 0 0 0 0 1 1 51
07 00F 0F 0 0 0 0 0 1 1 59
08 00F 0F 0 0 0 0 0 1 1 61
09 00F 0F 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 00F 0F 0 0 0 0 0 1 1 71
0d 00F 0F 0 0 0 0 0 1 1 79
0e 00F 0F 0 0 0 0 0 1 1 81
0f 00F 0F 0 0 0 0 0 1 1 89
10 00F 0F 1 1 0 1 0 1 1 91
11 000 00 1 0 0 0 0 0 0 00
12 00F 0F 1 1 0 1 0 1 1 99
13 00F 0F 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 00F 0F 1 1 0 1 0 1 1 A9
16 00F 0F 1 1 0 1 0 1 1 B1
17 000 00 1 0 0 0 0 0 0 00
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 03000000
....... : arbitration: 03
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 04000000
....... : arbitration: 04
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 00F 0F 1 1 0 1 0 1 1 B9
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ54 -> 2:6
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2395.1076 MHz.
..... host bus clock speed is 99.1591 MHz.
cpu: 0, clocks: 194938, slice: 38987
CPU0<T0:194928,T1:155936,D:5,S:38987,C:194938>
cpu: 1, clocks: 194938, slice: 38987
cpu: 3, clocks: 194938, slice: 38987
cpu: 2, clocks: 194938, slice: 38987
CPU1<T0:194928,T1:116944,D:10,S:38987,C:194938>
CPU2<T0:194928,T1:77936,D:31,S:38987,C:194938>
CPU3<T0:194928,T1:38976,D:4,S:38987,C:194938>
checking TSC synchronization across CPUs: passed.
migration_task 0 on cpu=0
migration_task 1 on cpu=1
migration_task 2 on cpu=2
migration_task 3 on cpu=3
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfd8b5, last bus=4
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Discovered primary peer bus 10 [IRQ]
PCI: Discovered primary peer bus 11 [IRQ]
PCI: Discovered primary peer bus 12 [IRQ]
PCI: Using IRQ router PIIX [8086/2480] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B2,I3,P0) -> 54
PCI->APIC IRQ transform: (B4,I4,P0) -> 21
PCI->APIC IRQ transform: (B4,I5,P0) -> 22
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
speakup: initialized device: /dev/synth, node (MAJOR 10, MINOR 25)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Starting kswapd
allocated 64 pages and 64 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.5.0 initialized
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
oprofile: can't get RTC I/O Ports
block: 1024 slots per queue, batch=256
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev f9
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: No IRQ known for interrupt pin A of device 00:1f.1. Probably buggy MP table.
PIIX4: chipset revision 2
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2060-0x2067, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x2068-0x206f, BIOS settings: hdc:pio, hdd:pio
hda: WDC WD400JB-00ENA0, ATA DISK drive
hdc: CDU5211, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c0438b04, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0438b04, I/O limit 4095Mb (mask 0xffffffff)
hda: 78165360 sectors (40021 MB) w/8192KiB Cache, CHS=77545/16/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
pci_hotplug: PCI Hot Plug PCI Core version: 0.4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 129k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 240k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 12:50:27 Sep 4 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x2000, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x2020, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x2040, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,6), internal journal
Adding Swap: 2047744k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
ohci1394: pci_module_init failed
ip_tables: (C) 2000-2002 Netfilter core team
Intel(R) PRO/1000 Network Driver - version 4.3.2-k1 NAPI (020618)
Copyright (c) 1999-2002 Intel Corporation.
divert: allocating divert_blk for eth0
eth0: Intel(R) PRO/1000 Network Connection
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw@saw.sw.com.sg> and others
divert: allocating divert_blk for eth1
eth1: OEM i82557/i82558 10/100 Ethernet, 00:30:48:20:11:3E, IRQ 22.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xd0a6c714).
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
next reply other threads:[~2002-12-16 1:15 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-12-16 1:15 ray [this message]
-- strict thread matches above, loose matches on Subject: below --
2003-01-03 18:03 (unknown) root
2002-09-17 13:22 (unknown), CStoeber
2002-08-28 22:02 (unknown), Ken.Olstad
2002-08-22 16:18 (unknown) R.C.Pasianot
2002-08-14 21:29 (unknown), Paul, Eric
2002-07-17 14:25 (unknown), HABIB ABIOLA
2002-07-17 6:47 (unknown) Lord Satanus Emperor of Acheron
2002-07-08 9:43 (unknown), Casey Thompson
2002-06-19 10:08 (unknown) PATROL Quality Assurance Account
2002-05-22 23:46 (unknown) Schroettner Robert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3.0.1.32.20021215171510.006d0b0c@pop.redshift.com \
--to=ray@redshift.com \
--cc=linux-smp@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox